Device Tree properties ranges and dma-ranges describe address mappings
required when moving between buses. Ensure this translation happens when
mapping MMIO addresses for DMA accesses.
This commit replaces another downstream commit that no longer applies as
of 6.18:
dma-direct: take dma-ranges/offsets into account in resource mapping
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The non-pi5 variant of tc358743 needs to update the compatible of
csi0 rather than csi1 if the cam0 override is used, otherwise it
gets loaded in Media Controller mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Remove the need for the user to know the limitations of this PWM
implementation by adjusting configuration requests to be the closest
acceptable value. Add a get_state method so that the actual values can
be queried.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
EMMC clock speeds are based around divisions of 52Mhz, not the 50MHz
used by SD. As such, relax the "full speed" check (intended to stop
any overclock whenever an operation has to be retried) so that any
requested speed of 50MHz or higher will be overclocked.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
EMMC clock speeds are based around divisions of 52Mhz, not the 50MHz
used by SD. As such, relax the "full speed" check (intended to stop
any overclock whenever an operation has to be retried) so that any
requested speed of 50MHz or higher will be overclocked.
See: https://github.com/raspberrypi/linux/issues/7120
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Switch the power management in the imx708 device driver to use auto-
suspend with a 5s timeout.
This improves mode switching time that avoids additional regulator
switch-on delays and common register I2C writes.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The new concept of MMIO DMA addresses is used to indicate things with
fixed addresses - hardware registers, not movable pages. As such it is
reasonable to bypass the SWIOTLB mapping logic, but not any CPU<->DMA
address translation that has been configured by Device Tree. Doing so
will break any drives using (possibly indirectly) dma_map_resource
for register addresses where ther is a non-identity mapping between
CPU and DMA addresses. A good example of this is the SDHOST MMC
interface on BCM283x SoCs.
Fix the bug by reinstating the phys_to_dma call in the MMIO code path.
N.B. The upstream SDHOST driver (drivers/mmc/host/bcm2835.c) is not
affected by this bug because it pulls bus/DMA addresses directly out
of Device Tree.
See: https://github.com/raspberrypi/linux/issues/7136
Fixes: e53d29f957 ("dma-mapping: convert dma_direct_*map_page to be phys_addr_t based")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add an overlay to allow composite video to be output on GPIOs 4-11
on Raspberry Pi 5, 500, 500+ or CM5 only, with an optional 108 MHz
clock on GPIO 0 and duplicate MSB on GPIO 27.
Requires composite video to be enabled and DPI to be disabled.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
The regulator compatible string changed, and implements the PWM
API instead of the backlight one, therefore requiring pwm-backlight
to sit inbetween.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Switch the power management in the imx477 device driver to use auto-
suspend with a 5s timeout.
This improves mode switching time that avoids additional regulator
switch-on delays and common register I2C writes.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Fix these two smatch warnings for the vc-sm-cma driver, rest were false
positives:
../vc-sm-cma/vc_sm.c:413
vc_sm_dma_buf_attach() warn: inconsistent returns '&buf->lock'.
Locked on : 396
Unlocked on: 413
../vc-sm-cma/vc_sm.c:1225
vc_sm_cma_ioctl_alloc() error: we previously assumed 'buffer' could be
null (see line 1113)
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
The 4056x3040 mode appears to need more vertical blanking lines
than any other, leaving a black bar at the bottom of the image.
Increase IMX477_VBLANK_MIN from 4 to 48 to compensate. (It may be
possible to reduce it slightly further, but fix the regression
for now).
https://github.com/raspberrypi/linux/issues/7109
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
hvs6 appears to have dropped support for the component order
field in 3 plane YUV formats.
Support them by swapping the Cb and Cr planes over when
reading the image pointers.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Pass-through mode disables all gamma and brightness processing, sending
the raw pixel data directly to the LEDs. It is enabled by setting the
brightness to zero, either in Device Tree or using the runtime method of
writing a single byte (in this case 0) to the device.
See: https://github.com/raspberrypi/linux/issues/7108
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Remove CONFIG_MEDIA_PCI_HAILO from all the arm64 defconfig files as this
driver is no longer built in the kernel tree.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Modify the PDAF Datatype of the Arducam 64MP camera from 0x30 to 0x12
so that the Raspberry Pi 5 cfe driver can receive PDAF data.
Signed-off-by: Lee Jackson <info@arducam.com>
There were various points where the loader was using uninitialised
data, had the potential to run off the end of an array, or was
handling core functions incorrectly. Fix these up.
Also handle 24bpp and 32bpp framebuffers.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We lost a line in the forward port, which meant that it always used
/dev/fb0, and complained that the sysfs nodes already existed.
Fixes: c91c9f257d ("fbdev: Allow client to request a particular /dev/fbN node")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Although the PIO throughput benefits from larger burst sizes, only the
first two DMA channels support a burst size of 8 - the others are capped
at 4. To avoid misconfiguring the PIO hardware, retrieve the actual
max_burst value from the DMA channel's capabilities.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This patch adds support for external FSIN-triggered snapshot mode
to the OmniVision OV9282 sensor driver. It enables frame capture
synchronized with an external hardware trigger signal.
Signed-off-by: Omer Faruk Edemen <ofedemen@lectrontech.com>
Upstream series https://lore.kernel.org/linux-media/20250917-csi-bgr-rgb-v3-0-0145571b3aa4@kernel.org/
The tc358743 is an HDMI to MIPI-CSI2 bridge. It can output all three
HDMI 1.4 video formats: RGB 4:4:4, YCbCr 4:2:2, and YCbCr 4:4:4.
RGB 4:4:4 is converted to the MIPI-CSI2 RGB888 video format, and listed
in the driver as MEDIA_BUS_FMT_RGB888_1X24.
Most CSI2 receiver drivers then map MEDIA_BUS_FMT_RGB888_1X24 to
V4L2_PIX_FMT_RGB24.
However, V4L2_PIX_FMT_RGB24 is defined as having its color components in
the R, G and B order, from left to right. MIPI-CSI2 however defines the
RGB888 format with blue first.
This essentially means that the R and B will be swapped compared to what
V4L2_PIX_FMT_RGB24 defines.
The proper MBUS format would be BGR888, so let's use that.
Fixes: d32d98642d ("[media] Driver for Toshiba TC358743 HDMI to CSI-2 bridge")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Masquerading Interrupt split transfers as Control puts the transfer into
the non-periodic handler in the hub. This stops the hub dropping
complete-split data in the microframe after a CSPLIT should have
arrived, improving resilience to host IRQ latency. Devices are none
the wiser - the handshake tokens are the same.
Originally devised by Hans Petter Selasky @ FreeBSD.
(v2: dwc2 needs an un-masquerade prior to channel interrupt handling)
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Step wise governor increases the mitigation level when the temperature
goes above a threshold and will decrease the mitigation when the
temperature falls below the threshold. If it were a case, where the
temperature hovers around a threshold, the mitigation will be applied
and removed at every iteration. This reaction to the temperature is
inefficient for performance.
The use of hysteresis temperature could avoid this ping-pong of
mitigation by relaxing the mitigation to happen only when the
temperature goes below this lower hysteresis value.
Signed-off-by: Ram Chandrasekar <rkumbako@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
drivers: thermal: step_wise: avoid throttling at hysteresis temperature after dropping below it
Signed-off-by: Serge Schneider <serge@raspberrypi.org>
Fix hysteresis support in gov_step_wise.c
Directly get hyst value instead of going through an
optional and, now, unimplemented function.
Signed-off-by: Jürgen Kreileder <jk@blackdown.de>
Extend the LED control features of the led-modes property by adding a
led-swap property. This allows the same led-modes values to be used
across designs where the LED assignments differ.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
To ensure we don't get a regression on handling reflect_[xy]
in the middle of the command line string, add a test for it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The command line parser was looking for an "=" before the ","
separator.
If the command line had reflect_[xy] before another option
which took a parameter, it would find the "=" from the second
option and assume it was associated with the reflect option,
generally leading to a parsing failure.
Handle this case by looking for both "," and "=", and taking
the first instance.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
All the matrix entries for the YUV to RGB conversion matrices were
being filled with the same coefficients.
Compute the values for the BT601, BT709, and BT2020 matrices in
both full and limited range, and program those into the hardware.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver previously set the global interrupt mask in the ECR register
in bcm54xx_config_init(), disabling all interrupts. This conflicts with
the configuration in bcm_phy_config_intr(), which enables or disables the
global interrupt mask as needed and is called earlier. As a result,
interrupts may remain globally disabled even when the IMR is configured
to unmask specific events.
Remove the ECR handling from bcm54xx_config_init() so that interrupt
enable/disable is managed exclusively by bcm_phy_config_intr().
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
On CM4/CM5, LED3 is used for ETH_LEDY, while LED4 may be unused or serve
as INT_N. Previously, both LEDs 3 and 4 were mirrored from LED1, which
overwrote the INT_N configuration on CM5.
Fix this by only shadowing LED1 to LED3, preserving the setting for
LED4/INT.
Fixes: 9704fab964 ("net: phy: broadcom: Allow ethernet LED mode to be set via device tree")
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
The phy specific structure is missing the pointers for handling
interrupts and link change notification. This results in interrupt's
being polled on CM5:
Fix this and copy the existing pointers from BCM54210E, which match the
implementation.
Before:
[3.501498] macb 1f00100000.ethernet eth0: PHY [1f00100000.ethernet-ffffffff:00] driver [Broadcom BCM54213PE] (irq=POLL)
After:
[3.597582] macb 1f00100000.ethernet eth0: PHY [1f00100000.ethernet-ffffffff:00] driver [Broadcom BCM54213PE] (irq=168)
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Enable by adding the following to cmdline.txt:
`fullscreen_logo_name=logo.tga fullscreen_logo=1`
Will show the logo file present in /lib/firmware/ on the screen.
This will be fullscreen and rendered early at boot.
Any remaining space is filled with solid color from the image border.
If TGA file is too big, image is clipped accordingly.
Signed-off-by: Ben Benson <ben.benson@raspberrypi.com>
Splash Screen: bug fix
Prevents fullscreen logos from being drawn multiple times.
With small enough logos, the image would be drawn multiple times across the screen.
Signed-off-by: Ben Benson <ben.benson@raspberrypi.com>
The patch "dmaengine: dw-axi-dmac: add per-channel AXI burst length
support" programs ARLEN/AWLEN from the snps,axi-max-burst-len array but
still exposed a single max_burst value via dma_get_slave_caps(). As a
result all channels reported 8 even when limited to 4, leading to
warnings:
dma dma2chan5: requested source burst length 8 exceeds supported 4
Add a .device_caps callback to return the correct per-channel max_burst.
This allows drivers like amba-pl011 to clamp burst lengths properly.
Fixes: 0e4e6a0c4f4e ("dmaengine: dw-axi-dmac: add per-channel AXI burst length support")
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Add a mechanism to allow clients to prefer some DMA channels over
others. This is required to allow high-bandwidth clients to request
one of the two "heavy" channels, but could also be used to prevent
some clients from hogging all channels.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The DesignWare AXI DMAC IP can be configured with heterogeneous channel
parameters. Allow maximum burst length to be set per-channel by making
snps,axi-max-burst-len an array.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
While we continue to use the downstream RP1 driver, update some other
Kconfig settings to recognise MFD_RP1 as a valid RP1 driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Drop from RGB to YUV422 output if RGB couldn't be supported
within the defined max_bpc and TMDS rates, and then try
dropping max_bpc.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Apparently some NVMe SSD implementations don't fall back to MSI cleanly,
instead making the driver allocate one queue via the legacy interrupt.
There are still only 32 vectors available, but should be sufficient for
the majority of use-cases on BCM2711.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Disabling tx_lpi or eee should not cause the value of tx_lpi_timer to
be lost, even though it is not useful until they are re-enabled.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add two new DT properties:
* microchip,eee-enabled - a boolean to enable EEE
* microchip,tx-lpi-timer - time in microseconds to wait before entering
low power state
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
For applications of the LAN78xx that don't have valid programmed
EEPROMs or OTPs, enabling both LEDs and auto-negotiation by default
seems reasonable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
lan78xx_link_reset explicitly clears the MAC's view of the PHY's IRQ
status. In doing so it potentially leaves the PHY with a pending
interrupt that will never be acknowledged, at which point no further
interrupts will be generated.
Avoid the problem by acknowledging any pending PHY interrupt after
clearing the MAC's status bit.
See: https://github.com/raspberrypi/linux/issues/2937
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
All other architectures do different cache operations depending on the
dir parameter. Fix arm64 to do the same.
This fixes udmabuf operations when syncing for read e.g. when the CPU
reads back a V4L2 decoded frame buffer.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Add a new minimal alignment field to the format structure. This minimal
alignment will be used if a stride has been provided by userland. If no
stride has been provided by userland (bytesperline == 0), the optimal
alignemnt will be used in the stride calculation.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Rename the align field in the format structure to opt_align to indicate
the optimal alignment for the format.
There is no functional change in this commit.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
There are now formats defined for 2-plane YUV420 at 10, 12,
and 16 bit depth using the most significant bits of the 16bit
word (P010, P012, and P016), and 3-plane YUV420 at those
depths using the least significant bits of the 16 bit word
(S010, S012, and S016).
VC4_GEN_6 can support all those formats although only composing
using at most 10bits of resolution, so add them as supported
formats for all planes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The function vc4_mock_atomic_add_output() should return a pointer, even
during error treatment. Use the proper macros to create pointers from
the error code.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
The version of the dwc-otg core used in BCM2835 through BCM2712 only does
whole-word writes, as well as needing the documented requirement for DMA
buffers to start on a word boundary.
Also, the alignment method used in the dwc2 driver doesn't handle the
case where the URB has the NO_TRANSFER_DMA_MAP flag set, so reject
buffers that have unaligned DMA start addresses. At least one whole page
should be mapped, so the BCM283x whole-word-write bug should be benign
in this case.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
During the probe() routine, the PiSP BE driver needs to power up the
interface in order to identify and initialize the hardware.
The driver resumes the interface by calling the
pispbe_runtime_resume() function directly, without going
through the pm_runtime helpers, but later suspends it by calling
pm_runtime_put_autosuspend().
This causes a PM usage count imbalance at probe time, notified by the
runtime_pm framework with the below message in the system log:
pispbe 1000880000.pisp_be: Runtime PM usage count underflow!
Fix this by resuming the interface using the pm runtime helpers instead
of calling the resume function directly and use the pm_runtime framework
in the probe() error path. While at it, remove manual suspend of the
interface in the remove() function. The driver cannot be unloaded if in
use, so simply disable runtime pm.
To simplify the implementation, make the driver depend on PM as the
RPI5 platform where the ISP is integrated in uses the PM framework by
default.
Fixes: 12187bd5d4 ("media: raspberrypi: Add support for PiSP BE")
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Document the gpio-gate-clock-releasing compatible string that enables
acquire/release GPIO semantics on gpio-gated clocks.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
Add support for the 'gpio-gate-clock-releasing' compatible string. The
behaviour is identical to that of 'gpio-gate-clock' but the gpio is
acquired on 'enable' and released on 'disable'.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
drm_helper_probe_add_cmdline_mode was looking for a match for
the width, height, and refresh rate within the EDID modes, but
didn't check the interlacing flag. That meant that with
video=1920x1080@50i would match any 1920x1080@50 mode that was
found.
The converse would be possible too if an interlaced mode with
matching resolution & refresh rate was found first.
Check the interlacing flag as well.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The brcmfmac driver uses the SDIO vendor ID values to identify which
vendor's driver extensions to use. However, the Cypress/Infineon devices
used by Rasperry Pi devices have a vendor ID of 02d0, which is Broadcom.
In order to use the Cypress driver extensions, modify the static mapping
for "43430" and "4345" (sic) to indicate that they are Cypress parts.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
dwc2_hc_start_transfer() overwrites hc->xfer_len for split-IN transfers.
Drivers may not allocate buffers that are multiples of the endpoint max
packet size, which may cause buffer overruns in the last transfer.
The hardware needs HCTSIZ to be set to a multiple of HCCHAR.MPS, so trim
chan->max_packet in dwc2_assign_and_init_hc().
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The HFNUM register increments on every microframe in HS mode, and USB
device drivers expect the returned frame count to relate to the overall
frame. Right-shift the returned value by 3 to drop the microframe bits.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
BCM2836 with Cortex-A7 cores has almost the same ARM_LOCAL interrupt
routing logic as BCM2837, so relax the compile guard to CONFIG_SMP not
CONFIG_ARM64.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Interrupts are dispatched round-robin but doing so trampled FIQ routing.
Taking a FIQ on a core without a handler installed is fatal.
Only modify bits 1:0 which are the IRQ route bits.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The 6.9 kernel introduced a large patchset [1] designed to make gpiochip
usage safe in the presence of potential hotplugging events. The changes
included protecting every gpiochip access with a claim of an interlock.
Running on a Pi 5 these changes reduce GPIO performance from userspace
by around 10%. The penalty would be proportionally higher from kernel,
as seen by SPI speed reductions.
Patch the gpiolib implementation to remove the protection of gpiochip
accesses. By providing alternative implementations of the relevant
macros, the changes are localised and therefore easier to verify.
See: https://github.com/raspberrypi/linux/issues/6854
[1] https://lwn.net/Articles/960024/
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The Renesas uPD controller is a bit more picky about validating Configure
Endpoint TRBs and requires that bit 0 of the ADD field is 1.
This is mentioned in xhci v1.2 s4.6.6.
Also drop a redundant helper function and reject invalid endpoints.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Distinguish between releasing the watchdog without requesting that it is
stopped, and failing to stop it when requested. The former is standard
behaviour for systemd, while the latter may be unexpected.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
A conditional had been left as == GEN_6_C, when it also applied
to GEN_6_D, resulting in an invalid change to the dlist on async
updates.
Fixes: b7b14b31c8 ("drm/vc4: plane: Add support for 2712 D-step.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Support vertical flip by setting REG_VREVERSE.
Additional registers also needs to be set per mode, according
to the readout direction (normal/inverted) as mentioned in the
data sheet.
Since the register IMX335_REG_AREA3_ST_ADR_1 is based on the
flip (and is set via vflip related registers), it has been
moved out of the 2592x1944 mode regs.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
In commit 81495a59ba ("media: imx335: Fix active area height discrepency")
the height for the mode struct was rectified to '1944'. However, the
name of mode struct is still reflecting to '1940'. Update it.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
The existing driver claims AHT20 support in i2c_device_id, but fails to:
1. Use the correct init command (0xBE for AHT20 vs 0xE1 for AHT10)
2. Omit AHT10_MODE_CYC which AHT20 doesn't support/require
Add proper initialization sequence and include "aosong,aht20" in the
device tree match table to fully support the AHT20.
Signed-off-by: Josh Martinez <8892161+joshermar@users.noreply.github.com>
As a follow-up to commit ef79eea9e4 ("drm/vc4: plane: Enable scaler
for YUV444 on GEN6"), the image looks a little soft when rendering at
1:1 due to the scaling filter being enabled.
Switch to using the nearest neighbour filter automatically when
not scaling in YUV444 to compensate.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
GEN6 requires the luma scaler to be enabled for YUV444 to
be rendered at 1:1, otherwise the source plane isn't rendered.
Fixes: 076eedaf76 ("drm/vc4: hvs: Add support for BCM2712 HVS")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
YUV444 support isn't officially supported by the hardware, but
worked if you told it the image was YUV422 with double the width
and altered chroma scaling.
Adding BCM2712 support gained a fetcher memory (UPM). The code
handling UPM allocations didn't have a case for YUV444, so only
allocated based on the base width, and therefore underflowed.
Increase the UPM allocation size for the luma plane of YUV444
to match.
Fixes: 076eedaf76 ("drm/vc4: hvs: Add support for BCM2712 HVS")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
At a high FPS with RAW10, there is frame corruption for 480p because the
rate_factor of 2 is used with the normal 2x2 bining [1]. This commit
ties the rate_factor to the selected binning mode. For the 480p mode,
analog 2x2 binning mode with a rate_factor of 2 is always used. For the
1232p mode the normal 2x2 binning mode is used for RAW10 while analog
2x2 binning mode is used for RAW8.
[1] raspberrypi#5493
Signed-off-by: Vinay Varma <varmavinaym@gmail.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reworked due to upstream changes
The enum binning_mode is redundant, it only uses values from the earlier
defined binning modes. Remove it.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Commit 0af46fbc33 ("media: i2c: imx219: Calculate crop rectangle
dynamically") meant that the 1920x1080 switched from using no binning
to using vertical binning but no horizontal binning.
Restore the original behaviour by ensuring the two binning settings
are the same.
Fixes: 0af46fbc33 ("media: i2c: imx219: Calculate crop rectangle dynamically")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
By default, the System Exit Latency and Maximum Exit Latency are used to
calculate hub port U1 and U2 timeout values. This has the effect of
aggressively power-managing a SuperSpeed link but devices are known to
report unfeasibly short device exit latencies in their descriptors,
which under certain usage conditions can significantly degrade
throughput as the link spends longer retraining than being in a useable
state.
The Intel heuristic approach calculates a reasonably large
endpoint-dependent U1 timeout, and uses a minimum U2 timeout that is
several multiples of typical U2 exit latencies.
Add a module parameter that defaults to using this scheme.
This should have the effect of squelching interop edge-cases where LPM
noticeably degrades performance, and avoid the usual workaround where
userspace manually disables it.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Certain versions of the VL805 firmware manipulate the endpoint Link
Control register to toggle ASPM on/off based on workload, but these
versions also report 0 in the Device Capability Acceptable Latency field
leaving the RC with ASPM disabled.
As it turns out, this EP has a broken L0s implementation so a) override
L1 latency to a sensible value and b) mask L0s.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The existing implementation for clkreq-mode="safe" leaves the HARD_DEBUG
with both control bits clear. This can cause link failure if L1
sub-states are enabled and if either of these conditions occurrs:
- The platform does not connect the CLRKEQ# signal to the EP, and a
pull-up is present on the line
- The platform connects the signal to the EP, and the EP enters an L1.x
or ClkPM state
Additional register bits in the HARD_DEBUG register can be used to force
the RC to drive CLKREQ# low. Also, un-advertise L1ss as a) additional
power savings can't be realised and b) enabling L1ss may incur
additional wake latency from L1.0.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The number of words to fetch for SAND formats on vc6 needs to account
for all pixels requested by width.
If cropping fractional pixels, then the width was being increased, but
fetch_count had already been computed. That led to insufficient words
being fetched, and the HVS locked up solid.
Apply the fixup for fractional pixel source cropping before computing
fetch_count.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
BCM2712/vc6 uses 256bit words when reading in P030/SAND128,
increased from 128bit on BCM2711/vc5.
Update the code for cropping the read area to handle the correct
word length.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add two features that assist in diagnosing link instability issues.
The debugfs additions allow for snapshots of the Physical Layer
statistics registers to be taken, during either free-running capture or
after a hardware-controlled capture interval.
To arm the capture engine (and reset the stats counters), write an
integer N to:
/sys/kernel/debug/pcie@<addr>/stats_trigger
The engine will run forever with a value of 0, or disarm after N
microseconds.
To snapshot the hardware stats counters, write to:
/sys/kernel/debug/pcie@<addr>/stats_snapshot
Reading this file will return the snapshot. If no writes have occurred
since boot, the snapshot will be of the initial link training period.
The ltssm_trace module parameter printk's the states during initial link
startup, in situations where failure to establish the link is a fatal
error.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Remove a bogus memory alignment check - transfers will be run bytewise
if needed - and add a check that the overall length is multiple of the
register size, otherwise there is residue.
See: https://github.com/raspberrypi/linux/issues/6733
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Commit 69dbba71ac ("drm/vc4: Add algorithmic handling for SAND")
lost a multiplication by the tile width when doing the pointer arithmetic
for cropping off columns for vc6.
Correct that computation.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Ilitek ILI9806E driver is used in the Pimoroni HyperPixel4
and potentially other displays. Whilst it can support multiple
interfaces, this driver only accounts for SPI configuration and
DPI video data.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This property can be used to delay deassertion of external fundamental
reset, which may be useful for endpoints that require an extended time for
internal setup to complete.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Some endpoints need longer than the minimum Tperst_clk time of 100us
that the PCIe specification allows for, as they may need to sequence
internal resets off the stable output of internal PLLs prior to removal
of fundamental reset. PCIe switches are an especially bad case, in some
cases requiring up to 100 milliseconds for stable downstream link
behaviour.
Parse the DT property brcm,tperst-clk-ms and use this to hold PERST# low
during brcm_pcie_start_link().
The BRCM RC typically outputs 200us of stable refclk before deasserting
PERST#. By masking/forcing the output signal while deasserting the
internal reset, the effect is to extend the length of time that the
refclk is active and stable before PERST# is released.
The TX lanes will enter the Polling state before PERST# is released, but
this appears to be harmless.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Some platforms may require an extended time with refclk active before
PERST# is released. Add a property to let the RC driver know how long to
wait.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The BCM2712 root complexes can interpret priority signalling in two
different ways, based on the incoming Traffic Class of a TLP.
The TLP TCs are assigned to separate internal request/response queues,
and assigned different AXI IDs. These queues can have outgoing AXI
transactions tagged based on:
- Static QoS values
- Dynamic QoS through internal backpressure
- Dynamic QoS with elevation based on Vendor Messages received by the RC
The VDM mechanism is of limited use due to implementation bugs, but the
implicit reordering due to separate ID assignment allows higher-priority
traffic from an EP to overtake other traffic in the RC and rest of the
system.
RP1 assigns TCs based on its internal bus managers, and internally tags
read requests to allow out-of-order completions, so these two features
operate in concert to provide priority service to e.g. MIPI camera or
display traffic.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
There is configurable priority forwarding hardware in this variant of the
Root Complex controller. Add optional properties to configure FIFO
backpressure or Vendor-Defined Message priority forwarding.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The PHY MDIO register map is different on BCM2712, and as the PHY input
clock is 54MHz not 100MHz, enabling refclk SSC is both broken and
unfixable.
Mask out attempts to enable SSC with a controller quirk.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
It appears that bits in the Root Control Register are reset with
perst_n, which means the PCI layer's call to enable CRS prior to
adding/scanning the bus has no effect. Open-code the enable in
brcm_pcie_start_link as a workaround.
Without CRS visibility, configuration reads issued by the CPU don't
retire if the endpoint returns a CRS response - the RC will poll until a
(large) timeout is reached. This means the core can stall for a long
time during boot.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
These chips use a UBUS-AXI bridge component that has configurable
timeout and error response handling.
Suppress AXI error responses to CPU requests, otherwise these are fatal
if they reach the ARM cluster, and set reasonably large timeouts for
both Mem and Cfg requests.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Pitch has no meaning if the modifier isn't DRM_FORMAT_MOD_LINEAR
as there is no guarantee that the value passed follows the
pattern that pitch * height = size.
Remove that check from framebuffer_check.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The SAND modifier with height 0 is now using the provided pitch as
the column stride, but the UBM allocation needs to be done based
on the plane width.
Recompute the width in these conditions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The SAND handling had been using what was believed to be a runtime
parameter in the modifier, however that has been clarified that
all permitted variants of the modifier must be advertised, so
making it variable wasn't practical.
With a rationalisation of how the producers of this format are
configured, we can switch to a variant that doesn't have as much
variation, and can be configured such that only 2 options are
required.
Add a modifier with value 0 to denote that the height of the luma
column matches the buffer height, and chroma column will be half
that due to YUV420.
A modifier of 1 denotes that the height of the luma column still
matches the buffer height, but the chroma column height is the same.
This can be used to replicate the previous behaviour.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc4's debugfs support was updated with drm_debugfs_entry whilst
BCM2712 support was in progress, and missed that the lookup
in vc6_hvs_debugfs_dlist still followed the old pattern.
Correct that lookup to avoid an invalid dereference.
Fixes: f7af8ae9d3 ("drm/vc4: hvs: Add support for BCM2712 HVS")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Supporting GL rendering of the new HEVC decoder pixel formats requires
Mesa 24.2.5 or later. There are a couple of minor issues holding up
switching to Mesa 24.
Drop the new pixel formats from enum_fmt so that FFMpeg will use
the older ones that earlier versions of Mesa do support.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The BCM2711 and BCM2712 SoCs used on Rapsberry Pi 4 and Raspberry
Pi 5 boards include an HEVC decoder block. Add a driver for it.
Signed-off-by: John Cox <john.cox@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: hevc_dec: Add in downstream single planar SAND variant
Upstream will take the multi-planar SAND format, but add back
in the downstream single planar variant for backwards compatibility
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: hevc_dec: Add module parameter for video_nr
To avoid user complaints that /dev/video0 isn't their USB
webcam, add downstream patch that allows setting the preferred
video device number.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds a binding for the HEVC decoder found on the BCM2711 / Raspberry Pi 4,
and BCM2712 / Raspberry Pi 5.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add V4L2_PIXFMT_NV12MT_COL128 and V4L2_PIXFMT_NV12MT_10_COL128
to describe the Raspberry Pi HEVC decoder NV12 multiplanar formats.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Raspberry Pi HEVC decoder uses a tiled format based on
columns for 8 and 10 bit YUV images, so document them as
NV12MT_COL128 and NV12MT_10_COL128.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Keep track of the number of requests and request objects of a media
device. Helps to verify that all request-related memory is freed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
By default when the last request object is completed, the whole
request completes as well.
But sometimes you want to manually complete a request in a driver,
so add a manual complete mode for this.
In req_queue the driver marks the request for manual completion by
calling media_request_mark_manual_completion, and when the driver
wants to manually complete the request it calls
media_request_manual_complete().
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
commit 59ac702a93 ("drm/vc4: Get the rid of DRM_ERROR()") converted
all calls to DRM_ERROR into drm_err, but also converted one DRM_DEBUG
into a drm_err.
Switch it back to drm_dbg.
Fixes: 59ac702a93 ("drm/vc4: Get the rid of DRM_ERROR()")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If an HDMI connector has no EDID and the mode is set via the
kernel command line, then drm_reset_display_info() is the only
thing that will have set up any of connector->display_info.
With commit 26ff1c38fc ("drm/connector: hdmi: Compute bpc
and format automatically"), it is now checked that
DRM_COLOR_FORMAT_RGB444 is supported. Whilst it doesn't fail
the request, it does log dev_warn for every commit, spamming
the log.
For HDMI connectors initialise the color_format field to say
it supports RGB444.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
It was noted that if PV1 was in use to drive DSI1, then the
writeback connector could not be used as HVS channel 2 was
already in use.
The HVS allows PV1 (HVS output 2) to be driven by any HVS
channel via the DSP3_MUX setting, but that was hardcoded to be
either 2 (for PV1) or disabled for TXP.
Expand the available channels field for PV1, and configure
DSP3_MUX accordingly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Slave addresses for DMA are meant to be supplied as physical addresses
(contrary to what struct snd_dmaengine_dai_dma_data does).
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add ALSA jack detection to the vc4-hdmi audio driver so userspace knows
when to add/remove HDMI audio devices.
Signed-off-by: David Turner <david.turner@raspberrypi.com>
bcm2835_dma_suspend_late is only used if CONFIG_PM_SLEEP is defined,
so make it's presence similarly conditional to avoid a build warning
(and hence error).
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
These fields should not be set by either the user or the kernel driver
so remove them. Replace them with padding bytes to maintain backward
compatibility with existing userland applications.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The principal differences between the downstream SDHOST driver and the
version accepted upstream driver are that the upstream version loses the
overclock support and DMA configuration via DT, but gains some tidying
up (and maintenance by the upstream devs).
Add the missing features (with the exception of the low-overhead logging)
as a patch to the upstream driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
v4l2: Add pisp compression format support to v4l2
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: rp1: cfe: Fix use of freed memory on errors
cfe_probe_complete() calls cfe_put() on both success and fail code paths.
This works for the success path, but causes the cfe_device struct to be
freed, even if it will be used later in the teardown code.
Fix this by making the ref handling a bit saner: Let the video nodes
have the refs as they do now, but also keep a ref in the "main" driver,
released only at cfe_remove() time. This way the driver does not depend
on the video nodes keeping the refs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: cfe: Fix width & height in cfe_start_channel()
The logic for handling width & height in cfe_start_channel() is somewhat
odd and, afaics, broken. The code reads:
bool start_fe = is_fe_enabled(cfe) &&
test_all_nodes(cfe, NODE_ENABLED, NODE_STREAMING);
if (start_fe || is_image_output_node(node)) {
width = node->fmt.fmt.pix.width;
height = node->fmt.fmt.pix.height;
}
cfe_start_channel() is called for all video nodes that will be used. So
this means that if, say, fe_stats is enabled as the last node, start_fe
will be true, and width and height will be taken from fe_stats' node.
The width and height will thus contain garbage, which then gets
programmed to the csi2 registers.
It seems that this often still works fine, though, probably if the width
& height are large enough.
Drop the above code, and instead get the width & height from the csi2
subdev's sink pad for the csi2 channel that is used. For metadata the
width & height will be 0 as before.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: cfe: Fix verbose debug print
The debug print in cfe_schedule_next_csi2_job() is printed every frame,
and should thus use cfe_dbg_irq() to avoid spamming, rather than cfe_dbg().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: cfe: Rename xxx_dbg_irq() to xxx_dbg_verbose()
Rename the xxx_dbg_irq() macros to xxx_dbg_verbose(), as they can be
used to verbose debugs outside irq context too.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: cfe: Add verbose debug module parameter
Expose the verbose debug flag as a module parameter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: cfe: Drop unused field
Drop 'sensor_embedded_data' field, as it is unused.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: cfe: Fix default meta format's field
Set default meta format's field to V4L2_FIELD_NONE, instead of zeroing
it which indicates V4L2_FIELD_ANY. Metadata doesn't have fields, so NONE
makes sense, and furthermore the default v4l2 link validation will check
for matching fields, or that the sink field is NONE.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: cfe: Fail streaming if FE_CONFIG node is not enabled
When the FE is enabled, ensure that the FE_CONFIG node is enabled.
Otherwise fail cfe_start_streaming() entirely.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: rp1_cfe: Remove PISP specific MBUS formats
Remove the MEDIA_BUS_FMT_PISP* format codcs entirely. For the image
pad formats, use the 16-bit Bayer format mbus codes instead. For the
config and stats pad formats, use MEDIA_BUS_FMT_FIXED.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: rp1_cfe: Fix link validate test for pixel format
Now that we have removed unique PISP media bus codes, the cfe format
table has multiple entries with the same media bus code for 16-bit
formats. The test in cfe_video_link_validate() did not account for this.
Fix it by testing the media bus code and the V4L2 pixelformat 4cc
together.
As a drive-by, ensure we have a valid CSI2 datatype id when programming
the hardware block.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: cfe: Set the CSI-2 link frequency correctly
Use the sensor provided link frequency to set the DPHY timing parameters
on stream_on. This replaces the hard-coded 999 MHz value currently being
used. As a fallback, revert to the original 999 Mhz link frequency.
As a drive-by, fix a 80-character line formatting error.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: cfe: Don't confuse MHz and Mbps
The driver was interchaning these units when talking about link rate.
Fix this to avoid confusion. Apart from the logging message change,
there is no function change in this commit.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: rp1: csi2: Fix missing reg writes
The driver has two places where it writes a register based on a
condition, and when that condition is false, the driver presumes that
the register has the reset value. This is not a good idea, so fix those
places to always write the register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: fe: Use ~0, not -1, when working with unsigned values
Use ~0, not -1, when working with unsigned values (-1 is not unsigned).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: Add back reg write debug prints
Add back debug prints in csi2 and pisp_fe reg_write() functions, but use
the 'irq' variants to avoid spamming in normal situation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: csi2: Track CSI-2 errors
Track the errors from the CSI-2 receiver: overflows and discards. These
are recorded in a table which can be read by the userspace via debugfs.
As tracking the errors may cause much more interrupt load, the tracking
needs to be enabled with a module parameter.
Note that the recording is not perfect: we only record the last
discarded DT for each discard type, instead of recording all of them.
This means that e.g. if the device is discarding two unmatched DTs, the
debugfs file only shows the last one recorded. Recording all of them
would need a more sophisticated recording system to avoid the need of a
very large table, or dynamic allocation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: csi2: Set values for enum csi2_mode
Set hardcoded values for enum csi2_mode, as the values will be
programmed to HW registers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: fe: Fix default mbus code
When pisp_fe_pad_set_fmt() is given an mbus code that CFE does not
support, it currently defaults to MEDIA_BUS_FMT_SBGGR10_1X10. This is
not correct, as FE does not support SBGGR10.
Set the default to MEDIA_BUS_FMT_SRGGB16_1X16 instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
drivers: media: cfe: Find the source pads on the sensor entity
The driver was assuming that pad 0 on the sensor entity was the
appropriate source pad, but this isn't necessarily the case.
With video-mux, it has the sink pads first, and then the source
pad as the last one.
Iterate through the sensor pads to find the relevant source pads.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: rp1: cfe: Expose find_format_by_pix()
Make find_format_by_pix() accessible to other files in the driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: cfe: Add cfe_find_16bit_code() and cfe_find_compressed_code()
Add helper functions which, given an mbus code, return the 16-bit
remapped mbus code or the compressed mbus code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: csi2: Use get_frame_desc to get CSI-2 VC and DT
Use get_frame_desc pad op for asking the CSI-2 VC and DT from the source
device driver, instead of hardcoding to VC 0, and getting the DT from a
formats table. To keep backward compatibility with sources that do not
implement get_frame_desc, implement a fallback mechanism that always
uses VC 0, and gets the DT from the formats table, based on the CSI2's
sink pad's format.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: cfe: Add is_image_node()
The hardware supports streaming from memory (in addition to streaming
from the CSI-2 RX), but the driver does not support this at the moment.
There are multiple places in the driver which uses
is_image_output_node(), even if the "output" part is not relevant. Thus,
in a minor preparation for the possible support for streaming from
memory, and to make it more obvious that the pieces of code are not
about the "output", add is_image_node() which will return true for both
input and output video nodes.
While at it, reformat also the metadata related macros to fit inside 80
columns.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: cfe: Dual purpose video nodes
The RP1 CSI-2 DMA can capture both video and metadata just fine, but at
the moment the video nodes are only set to support either video or
metadata.
Make the changes to support both video and metadata. This mostly means
tracking both video format and metadata format separately for each video
node, and using vb2_queue_change_type() to change the vb2 queue type
when needed.
Briefly, this means that the user can get/set both video and meta
formats to a single video node. The vb2 queue buffer type will be
changed when the user calls REQBUFS or CREATE_BUFS ioctls. This buffer
type will be then used as the "mode" for the video node when the user
starts the streaming, and based on that either the video or the meta
format will be used.
A bunch of macros are added (node_supports_xxx()), which tell if a node
can support a particular mode, whereas the existing macros
(is_xxx_node()) will tell if the node is currently in a particular mode.
Note that the latter will only work correctly between the start of the
streaming and the end of the streaming, and thus should be only used in
those code paths.
However, as the userspace (libcamera) does not support dual purpose
video nodes, for the time being let's keep the second video node as
V4L2_CAP_META_CAPTURE only to keep the userspace working.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: Drop LE handling
The driver registers for line-end interrupts, but never uses them. This
just causes extra interrupt load, with more complexity in the driver.
Drop the LE handling. It can easily be added back if later needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: cfe: Improve link validation for metadata
Improve the link validation for metadata by:
- Allowing capture buffers that are larger than the incoming frame
(instead of requiring exact match).
- Instead of assuming that a metadata unit ("pixel") is 8 bits, use
find_format_by_code() to get the format and use the bit depth from
there. E.g. bit depth for RAW10 metadata will be 10 bits, when we
move to the upstream metadata formats.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
drivers: media: cfe: Add more robust ISR handlers
Update the ISR logic to be more robust to sensors in problematic states
where interrupts may start arriving overlapped and/or missing.
1) Test for cur_frame in the FE handler, and if present, dequeue it in
an error state so that it does not get orphaned.
2) Move the sequence counter and timestamp variables to the node
structures. This allows the ISR to track channels running ahead when
interrupts arrive unordered.
3) Add a test to ensure we don't have a spurios (but harmlesS) call to
the FE handler in some circumstances.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: rp1: cfe: Fix error paths in cfe_start_streaming
Noted that if we get "node link is not enabled", then we also
get the videobuf2 splat for the driver not cleaning up correctly
on a failed start_streaming, and indeed we weren't returning the
buffers.
Checking the other error paths, noted that the "FE enabled, but
FE_CONFIG node is not" path was not calling pm_runtime_put.
Fix both paths.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drivers: media: cfe: Increase default size of embedded buffer
Increase the size of the default embedded buffer to 16k. This is done to
match what is advertised by the IMX219 driver and workaround a problem
where the embedded stream is not actually used. Without full streams API
support, the media pipeline validation will fail in these circumstances.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: rp1: cfe: Actually use the number of lanes configured
The driver was calling get_mbus_config to ask the sensor subdev
how many CSI2 data lanes it wished to use and with what other
properties, but then failed to pass that to the DPHY configuration.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: rp1: csi2: Fix csi2_pad_set_fmt()
The CSI-2 subdev's set_fmt currently allows setting the source and sink
pad formats quite freely. This is not right, as the CSI-2 block can only
do one of the following when processing the stream: 1) pass through as
is, 2) expand to 16-bits, 3) compress.
The csi2_pad_set_fmt() should take this into account, and only allow
changing the source side mbus code, compared to the sink side format.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: csi2: Use standard link_validate
The current csi2_link_validate() skips some important checks. Let's
rather use the standard v4l2_subdev_link_validate_default() as the
link_validate hook.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: csi2: Squash fixes
media: rp1: fe: Fix pisp_fe_pad_set_fmt()
pisp_fe_pad_set_fmt() allows setting the pad formats quite freely. This
is not correct, and the function should only allow formats as supported
by the hardware. Fix this by:
Allow no format changes for FE_CONFIG_PAD and FE_STATS_PAD. They should
always be the hardcoded initial ones.
Allow setting FE_STREAM_PAD freely (but the mbus code must be
supported), and propagate the format to the FE_OUTPUT0_PAD and
FE_OUTPUT1_PAD pads.
Allow changing the mbus code for FE_OUTPUT0_PAD and FE_OUTPUT1_PAD pads
only if the mbus code is the compressed version of the sink side code.
TODO: FE supports scaling and cropping. This should be represented here
too?
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: fe: Use standard link_validate
The current pisp_fe_link_validate() skips some important checks. Let's
rather use the standard v4l2_subdev_link_validate_default() as the
link_validate hook.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
drivers: media: cfe: Add 16-bit and compressed mono format support
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: rp1: cfe: Add missing remaps
8-bit bayer formats are missing remap definitions. Add them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
media: rp1: cfe: Add missing compressed remaps
16-bit bayer formats are missing compressed remap definitions. Add them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
drivers: media: pisp_be: pisp_fe: Update UAPI header licenses
Update the license tags on the pisp UAPI header files with the
"Linux-syscall-note" clause. Also replace the "GPL-2.0" tag with the
preferred "GPL-2.0-only" tag.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: rp1: cfe: Use the MIPI_CSI2_DT_xxx defines for csi_dt
Seeing as we now have the CSI2 data types defined, make use of
them instead of hardcoding the values.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: rp1: cfe: Add a csi_dt value for 16bit formats
Raw 16bit formats didn't have a csi_dt value defined, which
presumably would trip the WARN_ON(!fmt->csi_dt); in
cfe_start_channel.
The value is defined in CSI2 v2.0 as 0x2e, so set it accordingly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drivers: media: pisp_be: Add mono and 48-bit RGB pixel format support
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: pisp_be: Update seqeuence numbers of the buffers
Add a framebuffer sequence counter and increment on every completed job.
This counter is then used to update the VB2 buffer sequence count before
calling vb2_buffer_done().
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: cfe: Add remap entries for mono formats
The 8-bit and 16-bit mono formats were missing the appropriate remap
entries in the format table.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: rp1-cfe: Fix up link validation for CFE CFG input
After commit 5fd3e2412a ("media: v4l2-subdev: Support hybrid links
in v4l2_subdev_link_validate()") link_validate is called on V4L2
OUTPUT devices such as the CFE cfg buffers input.
The CFE link_validate function was assuming it was always the
sink of a link, which goes wrong on that port and does an invalid
dereference.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: rp1-cfe: Swap "raspberypi,rp1-cfe" compatible to downstream driver
Whilst we are wanting to maintain the downstream driver at the same time
as having the upstream merged, swap the "raspberypi,rp1-cfe" compatible
string across.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media/platform/raspberypi/rp1_cfe: Candidate fix for #5821
To avoid lost frame start in a subsequent session, avoid setting
the number of lanes back to 1 or putting CSI-2 Host into reset.
It's not clear if this is a watertight fix -- what if the camera
itself produced a truncated or garbled packet, or continued to
send until the next start? -- but it does seem to fix the issue.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drivers: media: rpi: cfe: Avoid unpack operation for 16-bit formats
The unpack operation is redundant for 16-bit sensor formats, don't set
the hardware to do it in these cases.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: cfe: Workaround for 16-bit mismatch in the hardware
Set the data type for 16-bit modes to 0 (wildcard) to workarond the
16-bit mismatch in hardware.
We also need to suppress the warning about DT == 0 on start stream in
these cases.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Implement a tristate-style option for "supports-cqe". If the property is
absent or zero, disable CQ completely. For 1, enable CQ unconditionally
for eMMC cards, and known-good SD cards. For 2, enable for eMMC cards,
and all SD cards that are not known-bad.
The sdhci-brcmstb driver needs to know about the tristate as its probe
sequence would otherwise override a disable in mmc_of_parse().
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
These cards have a known-good CQ implementation and are based on a
Longsys product. Add the MANFID for Longsys SD, and the particular CID
details for the Pi card.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
We have found that many SD cards in the field, even of the same make and
model, have latent bugs in their CQ implementation. Some product lines
have fewer bugs with newer manufacture dates, but this is not a
guarantee that a particular card is at a particular firmware revision
level.
Many of these bugs lead to card hangs or data corruption. Add a quirk to
mark a card as having a tested, working CQ implementation and ignore the
capability if absent.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The sensor has Low Conversion Gain (HCG) and High Conversion Gain (HCG)
modes, with the supposedly the HCG mode having better noise performance
at high gains.
As this parameter changes the gain range of the sensor, it isn't
possible to make this an automatic property, and there is no
suitable V4L2 control to set it, so just add it as a module parameter.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Copy the same validation logic as from the plane rotation property.
Fixes: 8fec3ff870 ("drm: Add a rotation parameter to connectors.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
When initialized from panel_bridge_attach(), connector should
allow interlaced modes rather than invariably rejecting them,
so that other components can validate them.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
The upstream addition of the kernel parameter cgroup_disable makes it
possible to configure cgroups at boot time. In theory, re-enabling a
disabled cgroup is simply a case of removing the relevant cgroup_disable
setting, but this is difficult if the setting comes from Device Tree.
Re-introduce cgroup_enable as a way around the problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
On Raspberry Pi 4 and earlier models the firmware provides
a low speed (up to 115200 baud) bit-bashed UART on arbitrary
GPIOs using the second VPU core.
The firmware driver is designed to support 19200 baud. Higher
rates up to 115200 seem to work but there may be more jitter.
This can be useful for debug or managing additional low
speed peripherals if the hardware PL011 and 8250 hardware
UARTs are already used for console / bluetooth.
The firmware driver requires a fixed core clock frequency
and also requires the VPU PWM audio driver to be disabled
(dtparam=audio=off)
Runtime configuration is handled via the vc-mailbox APIs
with the FIFO buffers being allocated in uncached VPU
addressable memory. The FIFO pointers are stored in spare
VideoCore multi-core sync registers in order to reduce the number
of uncached SDRAM accesses thereby reducing jitter.
Signed-off-by: Tim Gover <tim.gover@raspberrypi.com>
serial: rpi-fw-uart: Demote debug log messages
A dev_info call in rpi_fw_uart_configure causes kernel log output every
time one opens the UART. Demote it to dev_dbg.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
LBM is only relevant for each active dlist, so there is
no need to double-buffer the allocations.
Cache the allocations per plane so that we can ensure the
allocations are possible.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Following the example of [1], move the state allocation out of the init
function to make it thread safe.
[1] commit 7e0351ae91 ("drm/vc4: tests: Stop allocating the state in
test init")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The tests on vc4 (BCM2835-7) were checking for DSI1 muxing being
to restricted channel 2, and therefore muxing with TXP was impossible.
As we no longer have that restriction, update the capabilities
defined for DSI1, move the tests that used to be impossible to the
valid list, and extend for additional combinations that are now
possible.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The BCM2712 comes with a different LBM size computation than the
previous generations, so let's add the few examples provided as kunit
tests to make sure we always satisfy those requirements.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We'll start testing our planes code in situations where we will use more
than XRGB8888, so let's add a few common pixel formats.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We'll start to add some tests for the plane state logic, so let's create
a helper to add a plane to an existing atomic state.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Some tests will need to find a plane to run a test on for a given CRTC.
Let's create a small helper to do that.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current mock planes were just using the regular drm_plane_state,
while the driver expect struct vc4_plane_state that subclasses
drm_plane_state.
Hook the proper implementations of reset, duplicate_state, destroy and
atomic_check to create vc4_plane_state.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The BCM2712 has a simpler pipeline than the BCM2711, and thus the muxing
requirements are different. Create some tests to make sure we get proper
muxing decisions.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The BCM2712 has a simpler pipeline that can only output to a writeback
connector and two HDMI controllers.
Let's allow our kunit tests to create a mock of that pipeline.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Some tests will need to retrieve the output that was just allocated by
vc4_mock_atomic_add_output().
Instead of making them look them up in the DRM device, we can simply
make vc4_mock_atomic_add_output() return an error pointer that holds the
allocated output instead of the error code.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The DRM device pointer and the DRM encoder pointer are redundant, since
the latter is attached to the former and we can just follow the
drm_encoder->dev pointer.
Let's remove the drm_device pointer argument.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Testing whether the VideoCore generation we want to mock is vc5 or vc4
worked so far, but will be difficult to extend to support BCM2712 (VC6).
Convert to a switch.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This is a squash of all firmware-kms related patches from previous
branches, up to and including
"drm/vc4: Set the possible crtcs mask correctly for planes with FKMS"
plus a couple of minor fixups for the 5.9 branch.
Please refer to earlier branches for full history.
This patch includes work by Eric Anholt, James Hughes, Phil Elwell,
Dave Stevenson, Dom Cobley, and Jonathon Bell.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: Fixup firmware-kms after "drm/atomic: Pass the full state to CRTC atomic enable/disable"
Prototype for those calls changed, so amend fkms (which isn't
upstream) to match.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: Fixup fkms for API change
Atomic flush and check changed API, so fix up the downstream-only
FKMS driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: Make normalize_zpos conditional on using fkms
Eric's view was that there was no point in having zpos
support on vc4 as all the planes had the same functionality.
Can be later squashed into (and fixes):
drm/vc4: Add firmware-kms mode
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
drm/vc4: FKMS: Change of Broadcast RGB mode needs a mode change
The Broadcast RGB (aka HDMI limited/full range) property is only
notified to the firmware on mode change, so this needs to be
signalled when set.
https://github.com/raspberrypi/firmware/issues/1580
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc4/drv: Only notify firmware of display done with kms
fkms driver still wants firmware display to be active
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
ydrm/vc4: fkms: Fix margin calculations for the right/bottom edges
The calculations clipped the right/bottom edge of the clipped
range based on the left/top margins.
https://github.com/raspberrypi/linux/issues/4447
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: fkms: Use new devm_rpi_firmware_get api
drm/kms: Add allow_fb_modifiers
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
drm/vc4: Add async update support for cursor planes
Now that cursors are implemented as regular planes, all cursor
movements result in atomic updates. As the firmware-kms driver
doesn't support asynchronous updates, these are synchronous, which
limits the update rate to the screen refresh rate. Xorg seems unaware
of this (or at least of the effect of this), because if the mouse is
configured with a higher update rate than the screen then continuous
mouse movement results in an increasing backlog of mouse events -
cue extreme lag.
Add minimal support for asynchronous updates - limited to cursor
planes - to eliminate the lag.
See: https://github.com/raspberrypi/linux/pull/4971https://github.com/raspberrypi/linux/issues/4988
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
drivers/gpu/drm/vc4: Add missing 32-bit RGB formats
The missing 32-bit per pixel ABGR and various "RGB with an X value"
formats are added. Change sent by Dave Stevenson.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
drm: vc4: Fixup duplicated macro definition in vc4_firmware_kms
Both vc4_drv.h and vc4_firmware_kms.c had definitions for
to_vc4_crtc.
Rename the fkms one to make it unique, and drop the magic
define vc4_crtc vc4_kms_crtc
define to_vc4_crtc to_vc4_kms_crtc
that renamed half the variable and function names in a slightly
unexpected way.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: Fix FKMS for when the YUV chroma planes are different buffers
The code was assuming that it was a single buffer with offsets,
when kmstest uses separate buffers and 0 offsets for each plane.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: fkms: Rename plane related functions
The name collide with the Full KMS functions that are going to be made
public.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
drm/vc4_fkms: Fix up interrupt handler for both 2835/2711 and 2712
2712 has switched from using the SMI peripheral to another interrupt
source for the vsync interrupt, so handle both sources cleanly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: fkms: No SMI abuse needed on BCM2712
Since we don't use the (absent) SMI block to create interrupts on
BCM2712, there's no need to map any registers.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Currently, booting with no hdmi connected has:
pi@pi4:~ $ vcgencmd measure_clock hdmi pixel
frequency(9)=120010256
frequency(29)=74988280
After connecting hdmi we get:
pi@pi4:~ $ vcgencmd measure_clock hdmi pixel
frequency(9)=300005856
frequency(29)=149989744
and that persists after disconnecting hdmi
I can measure this on a power supply as 10mA@5.2V (52mW).
We should always remove clk_set_min_rate requests
when we no longer need them.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
The txp block can implement transpose as it writes out the image
data, so expose that through the new connector rotation property.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm: vc4: txp: Do not allow 24bpp formats when transposing
The hardware doesn't support transposing to 24bpp (RGB888/BGR888)
formats. There's no way to advertise this through DRM, so block
it from atomic_check instead.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
As the writeback connector doesn't have the same realtime
constraints of a live display, drop the panic priority for it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The transposer/writeback connector should be running with a
lower priority, so shouldn't be factored into the load
calculations.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Instead of having 48 generic overlay planes, assign 32 to the
writeback connector so that there is no ambiguity in wlroots
when trying to find a plane for composition using the writeback
connector vs display.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HVS can accept an arbitrary number of planes, provided
that the overall pixel read load is within limits, and
the display list can fit into the dlist memory.
Now that DRM will support 64 planes per device, increase
the number of overlay planes from 16 to 48 so that the
dlist complexity can be increased (eg 4x4 video wall on
each of 3 displays).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The register to enable/disable background fill was being set
from atomic flush, however that will be applied immediately and
can be a while before the vblank. If it was required for the
current frame but not for the next one, that can result in
corruption for part of the current frame.
Store the state in vc4_hvs, and update it on vblank.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The documentation says that the TPZ filter can not upscale,
and requesting a scaling factor > 1:1 will output the original
image in the top left, and repeat the right/bottom most pixels
thereafter.
That fits perfectly with upscaling a 1x1 image which is done
a fair amount by some compositors to give solid colour, and it
saves a large amount of LBM (TPZ is based on src size, whilst
PPF is based on dest size).
Select TPZ filter for images with source rectangle <=1.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Seeing as the HVS can be configured with regard the scaling filter,
and DRM now supports selecting scaling filters at a per CRTC or
per plane level, we can implement it.
Default remains as the Mitchell/Netravali filter, but nearest
neighbour is now also implemented.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
There are no MEDIA_BUS_FMT_* defines for GRB or BRG, and adding
them is a pain.
Add a DT override to allow setting the order.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The current reset code doesn't actually stop the hdmi output.
That makes it difficult for displays to handle a mode set.
Powering down the PLL does actually remove the hdmi signal
and makes mode sets more reliable
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
There appears to be a requirement for some devices
(I'm testing with a 8K VRROOM 40Gbps HDMI switch)
for a measable delay between removing the hdmi phy output from
the old mode, to enabling the hdmi phy output for the new mode.
Without the delay, a mode switch has a small change of getting a permanent
'no signal', which requires a subsequent mode switch or a unplug/replug
to redetect.
Switching between 4kp24/25/30 modes fails about 5% of time in my testing.
Add a delay to make it impossible to switch faster than this.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
The intention of the vc4.force_hotplug setting is to
ignore hotplug completely.
It can be used when a display toggles hotplug when
switching AV inputs, going into standby or changing a
KVM switch, and some side effect of that is unwanted.
It turns out while vc4.force_hotplug currently makes
hotplug always read as asserted, that isn't enough to
stop drm doing lots of stuff, including re-reading
the edid.
An example of what drm does with a hotplug deasert/assert
and vc4.force_hotplug=1 currently is:
https://paste.debian.net/hidden/dc07434b/
That is unwanted. Lets ignore the hotplug interrupt
completely so drm is blissfully unaware of the hotplug change.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
See: https://forum.libreelec.tv/thread/24783-tv-avr-turns-back-on-right-after-turning-them-off
While the kernel provides a :D flag for assuming device is connected,
it doesn't stop this function from being called and generating a cec_phys_addr_invalidate
message when hotplug is deasserted.
That message provokes a flurry of CEC messages which for many users results in the TV
switching back on again and it's very hard to get it to stay switched off.
It seems to only occur with an AVR and TV connected but has been observed across a
number of manufacturers.
The issue started with https://github.com/raspberrypi/linux/pull/4371
and this provides an optional way of getting back the old behaviour
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
If you disable HDR metadata, then the hardware should stop
sending the infoframe, and that is implemented by the
clear_infoframe hook which wasn't implemented. Add it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
With the command line parser now providing the information about
the tv mode, use that as the preferred choice for initialising the
default of the tv_mode property.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Similar to the ch7006 and nouveau drivers, introduce a "tv_mode" module
parameter that allow setting the TV norm by specifying vc4.tv_norm= on
the kernel command line.
If that is not specified, try inferring one of the most popular norms
(PAL or NTSC) from the video mode specified on the command line. On
Raspberry Pis, this causes the most common cases of the sdtv_mode
setting in config.txt to be respected.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
drm/vc4: Do not reset tv mode as this is already handled by framework
In vc4_vec_connector_reset, the tv mode is already reset to the
property default by drm_atomic_helper_connector_tv_reset, so there
is no need for a local fixup to potentially some other default.
Fixes: 96922af144 ("drm/vc4: Allow setting the TV norm via module parameter")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The DSI block appears to be able to come up stuck in a condition where
it leaves the lanes in HS mode or just jabbering. This stops LP
transfers from completing as there is no LP time available. This is
signalled via the LP1 contention error.
Enabling video briefly clears that condition, so if we detect the
error condition, enable video mode and then retry.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Some DSI peripheral drivers wish to send commands in the
post_disable or panel unprepare callback. These are called
after the DSI host's disable call, but before the host's
post_disable if pre_enable_prev_first is set.
Don't reset the block until post_disable to allow these
commands to be sent.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The TC358762 bridge and panel decodes the mode differently on
DSI0 to DSI1 for no obvious reason, and results in a shift off
the screen.
Whilst it would be possible to change the compatible used for
the panel, that then messes up Pi5.
As it appears to be restricted to vc4 DSI0, fix up the mode
in vc4_dsi.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The pixel to byte FIFO appears to not always reset correctly,
which can lead to colour errors and/or horizontal shifts.
Reset on every vblank to work around the issue.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The block must be enabled for the FIFO resets to be actioned,
so ensure this is the case.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The initialisation sequence differs slightly from the documentation
in that the clocks are meant to be running before resets and
similar.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
DSI0 is misbehaving and needs to action things on vblank to
work around it.
Add a new hook to call across during vblank.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The dmabuf import already checks that the backing buffer is contiguous
and rejects it if it isn't. vc4 also requires that the buffer is
in the bottom 1GB of RAM, and this is all correctly defined via
dma-ranges.
However the kernel silently uses swiotlb to bounce dma buffers
around if they are in the wrong region. This relies on dma sync
functions to be called in order to copy the data to/from the
bounce buffer.
DRM is based on all memory allocations being coherent with the
GPU so that any updates to a framebuffer will be acted on without
the need for any additional update. This is fairly fundamentally
incompatible with needing to call dma_sync_ to handle the bounce
buffer copies, and therefore we have to detect and reject mappings
that use bounce buffers.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We have a read-modify-write race when updating SCALER_DISPCTRL for
underrun and end-of-frame interrupts.
Ideally it would be fixed via a spinlock or similar, but that will
require a reasonable amount of study to ensure we don't get deadlocks.
The underrun reporting is only for debug, so disable it for now.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Users are reporting running out of DLIST memory. Add a
debugfs file to dump out all the allocations.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
During normal operations, the cursor position update is done through an
asynchronous plane update, which on the vc4 driver basically just
modifies the right dlist word to move the plane to the new coordinates.
However, when we have the overscan margins setup, we fall back to a
regular commit when we are next to the edges. And since that commit
happens to be on a cursor plane, it's considered a legacy cursor update
by KMS.
The main difference it makes is that it won't wait for its completion
(ie, next vblank) before returning. This means if we have multiple
commits happening in rapid succession, we can have several of them
happening before the next vblank.
In parallel, our dlist allocation is tied to a CRTC state, and each time
we do a commit we end up with a new CRTC state, with the previous one
being freed. This means that we free our previous dlist entry (but don't
clear it though) every time a new one is being committed.
Now, if we were to have two commits happening before the next vblank, we
could end up freeing reusing the same dlist entries before the next
vblank.
Indeed, we would start from an initial state taking, for example, the
dlist entries 10 to 20, then start a commit taking the entries 20 to 30
and setting the dlist pointer to 20, and freeing the dlist entries 10 to
20. However, since we haven't reach vblank yet, the HVS is still using
the entries 10 to 20.
If we were to make a new commit now, chances are the allocator are going
to give the 10 to 20 entries back, and we would change their content to
match the new state. If vblank hasn't happened yet, we just corrupted
the active dlist entries.
A first attempt to solve this was made by creating an intermediate dlist
buffer to store the current (ie, as of the last commit) dlist content,
that we would update each time the HVS is done with a frame. However, if
the interrupt handler missed the vblank window, we would end up copying
our intermediate dlist to the hardware one during the composition,
essentially creating the same issue.
Since making sure that our interrupt handler runs within a fixed,
constrained, time window would require to make Linux a real-time kernel,
this seems a bit out of scope.
Instead, we can work around our original issue by keeping the dlist
slots allocation longer. That way, we won't reuse a dlist slot while
it's still in flight. In order to achieve this, instead of freeing the
dlist slot when its associated CRTC state is destroyed, we'll queue it
in a list.
A naive implementation would free the buffers in that queue when we get
our end of frame interrupt. However, there's still a race since, just
like in the shadow dlist case, we don't control when the handler for
that interrupt is going to run. Thus, we can end up with a commit adding
an old dlist allocation to our queue during the window between our
actual interrupt and when our handler will run. And since that buffer is
still being used for the composition of the current frame, we can't free
it right away, exposing us to the original bug.
Fortunately for us, the hardware provides a frame counter that is
increased each time the first line of a frame is being generated.
Associating the frame counter the image is supposed to go away to the
allocation, and then only deallocate buffers that have a counter below
or equal to the one we see when the deallocation code should prevent the
above race from occurring.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
DSI0 and DSI1 have different widths for the command FIFO (24bit
vs 32bit), but the driver was assuming the 32bit width of DSI1
in all cases.
DSI0 also wants the data packed as 24bit big endian, so the
formatting code needs updating.
Handle the difference via the variant structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Using increased bit depth for no reason increases power
consumption, and differs from the behaviour prior to the
conversion to use the HDMI helper functions.
Initialise the state max_bpc and requested_max_bpc to the
minimum value supported. This only affects Raspberry Pi,
as the other users of the helpers (rockchip/inno_hdmi and
sunx4i) only support a bit depth of 8.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
ws2812-pio-rp1 is a PIO-based driver for WS2812 LEDS. It creates a
character device in /dev, the default name of which is /dev/leds<n>,
where <n> is the instance number. The number of LEDS should be set
in the DT overlay, as should whether it is RGB or RGBW, and the default
brightness.
Write data to the /dev/* entry in a 4 bytes-per-pixel format in RGBW
order:
RR GG BB WW RR GG BB WW ...
The white values are ignored unless the rgbw flag is set for the device.
To change the brightness, write a single byte to offset 0, 255 being
full brightness and 0 being off.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Use the PIO hardware on RP1 to implement a PWM interface.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
pwm: rp1: use pwmchip_get_drvdata() instead of container_of()
The PWM framework may not embed struct pwm_chip within the driver’s
private data. Using container_of() can result in accessing invalid
memory or NULL pointers, especially after recent kernel changes.
Switch to pwmchip_get_drvdata() to reliably access the driver data.
This resolves kernel warnings and probe failures seen after updating
from kernel 6.12.28 to 6.12.34 [1]
While at it remove the now obsolete `struct pwm_chip chip` member from
`struct pwm_pio_rp1`.
[1] https://github.com/raspberrypi/linux/issues/6971
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Provide remote access to the PIO hardware in RP1. There is a single
instance, with 4 state machines.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: rp1-pio: Support larger data transfers
Add a separate IOCTL for larger transfer with a 32-bit data_bytes
field.
See: https://github.com/raspberrypi/utils/issues/107
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: rp1-pio: More logical probe sequence
Sort the probe function initialisation into a more logical order.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: rp1-pio: Minor cosmetic tweaks
No functional change.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: rp1-pio: Add in-kernel DMA support
Add kernel-facing implementations of pio_sm_config_xfer and
pio_xm_xfer_data.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: rp1-pio: Handle probe errors
Ensure that rp1_pio_open fails if the device failed to probe.
Link: https://github.com/raspberrypi/linux/issues/6593
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: rp1-pio: SM_CONFIG_XFER32 = larger DMA bufs
Add an ioctl type - SM_CONFIG_XFER32 - that takes uints for the buf_size
and buf_count values.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc/rp1-pio: Fix copy/paste error in pio_rp1.h
As per the subject, there was a copy/paste error that caused
pio_sm_unclaim from a driver to result in a call to
pio_sm_claim. Fix it.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: rp1-pio: Fix parameter checks wihout client
Passing bad parameters to an API call without a pio pointer will cause
a NULL pointer exception when the persistent error is set. Guard
against that.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: rp1-pio: Convert floats to 24.8 fixed point
Floating point arithmetic is not supported in the kernel, so use fixed
point instead.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: rp1-pio: Error out on incompatible firmware
If the RP1 firmware has reported an error then return that from the PIO
probe function, otherwise defer the probing.
Link: https://github.com/raspberrypi/linux/issues/6642
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: rp1-pio: Demote fw probe error to warning
Support for the RP1 firmware mailbox API is rolling out to Pi 5 EEPROM
images. For most users, the fact that the PIO is not available is no
cause for alarm. Change the message to a warning, so that it does not
appear with "quiet" in cmdline.txt.
Link: https://github.com/raspberrypi/linux/issues/6642
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: rp1-pio: Don't just reuse the same DMA buf
A missing pointer increment meant that not only was the same buffer
being reused again and again, there was also no protection against
using it simultaneously for multiple transfers. Fix that basic bug, and
also move a similar increment to before the transfer is started, which
feels less racy.
See: https://github.com/raspberrypi/linux/issues/6919
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: rp1-pio: Fix a config_xfer error path
If the DMA channel allocation fails, the relevant dma_configs entry
should be marked as no longer claimed, otherwise rp1_pio_sm_dma_free
will be called with an error number as a DMA channel pointer.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: rp1-pio: Request a DMA burst size of 8
Improve DMA performance by increasing the burst size to 8.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The RP1 firmware runs a simple communications channel over some shared
memory and a mailbox. This driver provides access to that channel.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
firmware: rp1: Simplify rp1_firmware_get
Simplify the implementation of rp1_firmware_get, requiring its clients
to have a valid 'firmware' property. Also make it return NULL on error.
Link: https://github.com/raspberrypi/linux/issues/6593
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
firmware: rp1: Linger on firmware failure
To avoid pointless retries, let the probe function succeed if the
firmware interface is configured correctly but the firmware is
incompatible. The value of the private drvdata field holds the outcome.
Link: https://github.com/raspberrypi/linux/issues/6642
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
firmware: rp1: Rename to rp1-fw to avoid module name collision
There is already the driver in drivers/mfd/rp1.ko, so having
drivers/firmware/rp1.ko can cause issues when using modinfo
and similar, and we can get errors with "Module rp1 is already
loaded" when trying to load it.
Rename the module so that the name is unique.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
mailbox: rp1: Don't claim channels in of_xlate
The of_xlate method saves the calculated event mask in the con_priv
field. It also rejects subsequent attempt to use that channel because
the mask is non-zero, which causes a repeated instantiation of a client
driver to fail.
The of_xlate method is not meant to be a point of resource acquisition.
Leave the con_priv initialisation, but drop the test that it was
previously zero.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The Raspberry Pi RP1 includes 2 M3 cores running firmware. This driver
adds a mailbox communication channel to them via a doorbell and some
shared memory.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Attempting to start a non-idle channel causes an error message to be
logged, and is inefficient. Test for emptiness of the desc_issued list
before doing so.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The xHC may commence Host Initiated Data Moves for streaming endpoints -
see USB3.2 spec s8.12.1.4.2.4. However, this behaviour is typically
counterproductive as the submission of UAS URBs in {Status, Data,
Command} order and 1 outstanding IO per stream ID means the device never
enters Move Data after a HIMD for Status or Data stages with the same
stream ID. For OUT transfers this is especially inefficient as the host
will start transmitting multiple bulk packets as a burst, all of which
get NAKed by the device - wasting bandwidth.
Also, some buggy UAS adapters don't properly handle the EP flow control
state this creates - e.g. RTL9210.
Set Host Initiated Data Move Disable to always defer stream selection to
the device. xHC implementations may treat this field as "don't care,
forced to 1" anyway - xHCI 1.2 s4.12.1.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
SPI transfers are of defined length, unlike some UART traffic, so it is
safe to let the DMA controller choose a suitable memory width.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
For devices where transfer lengths are not known upfront, there is a
danger when the destination is wider than the source that partial words
can be lost at the end of a transfer. Ideally the controller would be
able to flush the residue, but it can't - it's not even possible to tell
that there is any.
Instead, allow the client driver to avoid the problem by setting a
smaller width.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Some connectors, particularly writeback, can implement flip
or transpose operations as writing back to memory.
Add a connector rotation property to control this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Some hardware will implement transpose as a rotation operation,
which when combined with X and Y reflect can result in a rotation,
but is a discrete operation in its own right.
Add an option for transpose only.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The limit of 32 planes per DRM device is dictated by the use
of planes_mask returning a u32.
Change to a u64 such that 64 planes can be supported by a device.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The non-desktop property "Indicates the output should be ignored for
purposes of displaying a standard desktop environment or console."
That sounds like it should be true for all writeback and virtual
connectors as you shouldn't render a desktop to them, so set it
by default.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The DHT11 datasheet is pretty cryptic, but it does suggest that after
each integer value (humidity and temperature) there are "decimal"
values. Validate these as integers in the range 0-9 and treat them as
tenths of a unit.
Link: https://github.com/raspberrypi/linux/issues/6220
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
For platforms that have xHCI controllers attached over PCIe, and
non-coherent routes to main memory, a theoretical race exists between
posting new TRBs to a ring, and writing to the doorbell register.
In a contended system, write traffic from the CPU may be stalled before
the memory controller, whereas the CPU to Endpoint route is separate
and not likely to be contended. Similarly, the DMA route from the
endpoint to main memory may be separate and uncontended.
Therefore the xHCI can receive a doorbell write and find a stale view
of a transfer ring. In cases where only a single TRB is ping-ponged at
a time, this can cause the endpoint to not get polled at all.
Adding a readl() before the write forces a round-trip transaction
across PCIe, definitively serialising the CPU along the PCI
producer-consumer ordering rules.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
If a device frequently NAKs, it can exhaust the scheduled handshakes in
a frame. It will then not get polled by the controller until the next
frame interval. This is most noticeable on FS devices as the controller
schedules a small set of transactions only once per full-speed frame.
Setting the ENH_PER_NAK_FS/LS bits in the GUCTL1 register increases the
number of transactions that can be scheduled to Async (Control/Bulk)
endpoints in the respective frame time. In the FS case, this only
applies to FS devices directly connected to root ports.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Add two quirk properties that control whether or not the controller
issues many more handshakes to FS/HS Async endpoints in a single
(micro)frame. Enabling these can significantly increase throughput for
endpoints that frequently respond with NAKs.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
A user has reported that a card of this model from late 2021 doesn't
work, so extend the date range and make it match on all card sizes.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
As a workaround (and possibly a fix) for CPU spins observed on BCM2837,
use ptep_clear_flush_young instead of ptep_test_and_clear_young inside
lru_gen_look_around in order to expose PTE changes to the MMU. Note that
on architectures that don't require an explicit flush,
ptep_clear_flush_young just calls ptep_test_and_clear_young.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Some apps like linpack use numa_setpolicy to disable numa,
but that tends to have a significant performance hit for us.
If you have a cmdline.txt setting of numa_policy (to something other
than default), then lets ignore runtime changes and stick with
the cmdline.txt setting.
Not specifying numa_setpolicy in cmdline, or setting
numa_setpolicy=default(*) will allow runtime settings to work.
(*) easier to do when numa_setpolicy=interleave is set in DT.
Ignore logging for the first 40 seconds as there are some
expected switches during boot.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Show process name in set_mempolicy() ignored message
Signed-off-by: Trevor Man <tman_github@trejan.com>
To help work around certain memory controller limitations or similar, a
random NUMA allocation memory policy is added.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Add iommu_dma_numa_policy= kernel parameter which can be used to modify
the NUMA allocation policy of remapped buffer allocations.
Policy is only used for devices which are not associated with a NUMA node.
Syntax identical to what tmpfs accepts as it's mpol argument is accepted.
Some examples:
iommu_dma_numa_policy=interleave
iommu_dma_numa_policy=interleave=skip-interleave
iommu_dma_numa_policy=bind:0-3,5,7,9-15
iommu_dma_numa_policy=bind=static:1-2
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Add numa_policy kernel argument to allow overriding the kernel's default
NUMA policy at boot time.
Syntax identical to what tmpfs accepts as it's mpol argument is accepted.
Some examples:
numa_policy=interleave
numa_policy=interleave=skip-interleave
numa_policy=bind:0-3,5,7,9-15
numa_policy=bind=static:1-2
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
The i.MX8MP makes calls on it's source device to determine
the link-frequency that should be configured on the CSI2 receiver.
When the source is behind a video mux, we need to pass this call through
to the connected device.
Map the control handler of the source device to the video-mux,
essentially proxying all controls on the mux to the device which has
it's link enabled.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Add EXPORT_SYMBOL_GPL() for find_cpio_data() so that loadable modules
may also parse uncompressed cpio.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
The Sony IMX500 is a stacked 1/2.3-inch CMOS digital image sensor and
inbuilt AI processor with an active array CNN (Convolutional Neural
Network) inference engine. The native sensor size is 4056H x 3040V, and
the module also contains an in-built ISP for the CNN. The module is
programmable through an I2C interface with firmware and neural network
uploads being made over SPI. This driver supports imaging only.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
media: i2c: imx500: Inbuilt AI processor support
Add support for the IMX500's inbuilt AI processor. The IMX500 program
loader, AI processor firmware, DNN weights are accessed via the kernel's
firmware interface on 'open' and are transferred to the IMX500 over SPI.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
media: i2c: imx500: Enable LED during SPI transfers
The Raspberry Pi 'AI Camera' is equipped with an LED. Enable this LED
during SPI transfers to indicate to the end-user that progress is being
made during large tramsfers.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
drivers: media: imx500: Fixes for vblank control
Reduce the default/max framerate of the 2x2 binned mode to 30fps.
The current limit of 50fps can cause the sensor to produce corrupt
frames and cause missing framing events.
Also fixup the vblank control min/max/default/step paramters when
setting up.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: imx500: Simplify the vblank control init
Set the VBLANK control minimum and default values to IMX500_VBLANK_MIN
unconditionally everywhere.
Remove the mode specific framerate_default parameter, it is now unused.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: imx500: Enable LS correction
This correction is calibrated to approx 5000K.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
imx500: Fix for long exposure setup
The IMX500 (unlike the IMX477/IMX708) requires two regsiters to be set
for the exposure shift value to work correctly. The additional register
write (which was missing) is for the integration time shift.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: imx500: Enable sensor temperature monitoring
The register needs to be disabled before loading any firmware, otherwise
the upload fails for unknown reasons. Re-enable before starting the
sensor streaming.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: imx500: Add device id readback control
Add a new custom control V4L2_CID_USER_GET_IMX500_DEVICE_ID to allow
userland to query the device id from the IMX500 sensor eeprom.
Note that this device id can only be accessed when a network firmware
has been upoloaded to the device, so cannot be cached on probe.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx500: pm_runtime error paths
This change amends various error-paths in imx500_start_streaming() to
ensure that pm_runtime refcounts do not remain erroneously incremented
on failure.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
media: i2c: imx500: GPIO acquire/release semantics
When the imx500 driver is used as part of the 'AI Camera', the poweroff
state is never reached as the camera and gpio driver share a regulator.
By releasing the GPIOs when they are not in use, 'AI Camera' is able to
achieve a powered-down state.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
media: i2c: imx500: input tensor injection
Input tensor injection is a debug feature that allows a user-controlled
input to be passed directly to IMX500's inference engine (bypassing the
in-built ISP).
Three new custom controls are added to ENABLE_INJECTION before streaming
begins, to provide appropriate input tensors via an INPUT_TENSOR_FD, and
to provide notification of DNN results in the sensor output via
INJECTION_CMP_FRM.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
Add YAML device tree binding for the Sony IMX500 CMOS image sensor /
CNN inference engine. Also, add a MAINTAINERS entry.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
The check if the oscillator stop bit is set was reading from Control_1
register instead of the Seconds register.
This caused the Seconds register to be incorrectly changed if bit 7 of
Control_1 happens to be set.
Signed-off-by: Axel Hammarberg <axel.hammarberg@gmail.com>
In the same way that other subsystems support the setting of device
id numbers from Device Tree aliases, allow gpiochip numbers to be
derived from "gpiochip<n>" aliases.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The DW SPI interface has a 16-bit clock divider, where the bottom bit
of the divisor must be 0. Limit how low the clock speed can go to
prevent the clock divider from being truncated, as that could lead to
a much higher clock rate than requested.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Ensure the transmit FIFO has emptied before ending the transfer by
dropping the TX threshold to 0 when the last byte has been pushed into
the FIFO. Include a similar fix for the non-IRQ paths.
See: https://github.com/raspberrypi/linux/issues/6285
Fixes: 6014649de7 ("spi: dw: Save bandwidth with the TMOD_TO feature")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Do an end-run around ASoC in lieu of not being able to easily find the
associated DMA controller capabilities.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
There's no real need to constrain MEM access widths to 32-bit (or
narrower), as the DMAC is intelligent enough to size memory accesses
appropriately. Wider accesses are more efficient.
Similarly, MEM burst lengths don't need to be a function of DEV burst
lengths - the DMAC packs/unpacks data into/from its internal channel
FIFOs appropriately. Longer accesses are more efficient.
However, the DMAC doesn't have complete support for unaligned accesses,
and blocks are always defined in integer multiples of SRC_WIDTH, so odd
source lengths or buffer alignments will prevent wide accesses being
used, as before.
There is an implicit requirement to limit requested DEV read burst
lengths to less than the hardware's maximum configured MSIZE - otherwise
RX data will be left over at the end of a block. There is no config
register that reports this value, so the AXI burst length parameter is
used to produce a facsimile of it. Warn if such a request arrives that
doesn't respect this.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Disabling the peripheral resets controller state which has a dangerous
side-effect of disabling the DMA handshake interface while it is active.
This can cause DMA channels to hang.
The error recovery pathway will wait for DMA to stop and reset the chip
anyway, so mask further FIFO interrupts and let the transfer finish
gracefully.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
TMOD_RO is the receive-only mode that doesn't require data in the
transmit FIFO in order to generate clock cycles. Using TMOD_RO when the
device doesn't care about the data sent to it saves CPU time and memory
bandwidth.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
TMOD_TO is the transmit-only mode that doesn't put data into the receive
FIFO. Using TMOD_TO when the user doesn't want the received data saves
CPU time and memory bandwidth.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The firmware advertises its features as a string of words separated by
spaces. Ensure that feature names are only matched in their entirety.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The snps,block-size DT property declares the maximum block size for each
channel of the dw-axi-dmac. However, the driver ignores these when
setting max_seg_size and uses MAX_BLOCK_SIZE (4096) instead.
To take advantage of the efficiencies of larger blocks, calculate the
minimum block size across all channels and use that instead.
See: https://github.com/raspberrypi/linux/issues/6256
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The Raspberry Pi RP2040 GPIO bridge is an I2C-attached device exposing
both a Tx-only SPI controller, and a GPIO controller.
Due to the relative difference in transfer rates between standard-mode
I2C and SPI, the GPIO bridge makes use of 12 MiB of non-volatile storage
to cache repeated transfers. This cache is arranged in ~8 KiB blocks and
is addressed by the MD5 digest of the data contained therein.
Optionally, this driver is able to take advantage of Raspberry Pi RP1
GPIOs to achieve faster than I2C data transfer rates.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
spi: rp2040-gpio-bridge: Add debugfs progress indicator
Useful for tracking upload progress via userspace.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
spi: rp2040-gpio-bridge: add missing MD5 dependency
rp2040-gpio-bridge relies on the md5 crypto driver. This dependency
cannot be determined automatically as rp2040-gpio-bridge does not
use any of md5's symbols directly.
Declare a soft 'pre' dependency on md5 to ensure that it is included and
loaded before rp2040-gpio-bridge.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
spi: rp2040-gpio-bridge: fix gpiod error handling
In some circumstances, devm_gpiod_get_array_optional() can return
PTR_ERR rather than NULL to indicate failure. Handle these cases.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
spi: rp2040-gpio-bridge: probe: Cfg fast_xfer clk
Fast transfer mode requires that the first bit of data is clocked with a
rising edge. This can cause extra bits of data to be clocked on hardware
where the clock signal uses a pull-up. This change ensures that clk is
driven low before fast data transfer mode is entered.
Signed-off-by: Richard Oliver <richard.oliver@raspberrypi.com>
Offset the backend dev-nodes starting at /dev/video20
onwards to maintain backward compatibility with the
pre-upstreamed kernel driver.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add helpers to set and get vchiq driver data. vchiq_set_drvdata() and
vchiq_get_drvdata() wraps dev_set_drvdata() and dev_get_drvdata()
respectively.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Add version 4.17.1 of the Hailo PCIe device drivers.
Sourced from https://github.com/hailo-ai/hailort-drivers/
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: pcie: hailo: Fix include paths
An attempt to fix the include paths - they look reasonable, but the
GitHub auto-builds fail.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
drivers: media: pci: Update Hailo accelerator device driver to v4.18.0
Sourced from https://github.com/hailo-ai/hailort-drivers/
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: pci: Add wrapper after removal of follow_pfn
drivers: media: pci: Fix Hailo compile warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
drivers: media: pci: Update Hailo accelerator device driver to v4.19
Sourced from https://github.com/hailo-ai/hailort-drivers/
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: pci: Update Hailo accelerator device driver to v4.20
Sourced from https://github.com/hailo-ai/hailort-drivers
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: pci: hailo: Fix kernel warning when calling find_vdma()
Calling this function without holding the mmap_read_lock causes the
kernel to throw an error message, spamming the dmesg logs when running
the Hailo hardware.
Fix it by adding the approprite lock/unlock functions around find_vdma().
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: pci: hailo: Better lock handling when calling find_vdma()
Due to possible instabilities, reduce the mmap read lock time to only
cover the call to find_vdma().
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Pass the DRM connector name to any configured backlight
device so that userspace can associate the two items.
Ideally this should be in drm_panel, but it is bridge/panel
that creates the drm_connector and therefore knows the name.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/bridge: panel: Ensure backlight is reachable
Ensure that the various options of modules vs builtin results
in being able to call into the backlight code.
https://github.com/raspberrypi/linux/issues/6198
Fixes: 573f8fd0ab ("drm/bridge: panel: Name an associated backlight device")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The naming of backlight devices is not terribly useful for
associating a backlight controller with a display (assuming
it is attached to one).
Add a sysfs node that will return a display name that can be set
by other subsystems.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Even when configured to use only gpiod CS lines, the DW SPI controller
still expects a bit to be set in the SER register, otherwise transfers
stall. For the csgpiod case, nominate bit 0 for the job.
See: https://github.com/raspberrypi/linux/issues/6159
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Reverts 8a4b2fc9c9 ("drm/bridge: tc358762: Split register programming from pre-enable to enable")
as we want the config commands sent before video starts.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The autodetection of resolution/timing by the TC358762 can lead
to the display being shifted by a pixel or two.
Program the TC358762 with the requested mode timing so that
it can reproduce it accurately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
"rotation" is listed as a standard property of panels in panel-common.yaml,
therefore it would be logical to process that from within the core
code should a panel driver not implement the get_orientation hook.
Call of_drm_get_panel_orientation from
drm_connector_set_orientation_from_panel to get that information.
This removes the need for any boiler-plate in panel drivers for calling
drm_connector_set_orientation_from_panel or
drm_connector_set_panel_orientation.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This code:
for_each_sg(sgl, sg, sg_len, i)
num_sgs += DIV_ROUND_UP(sg_dma_len(sg), axi_block_len);
determines how many hw_desc are allocated.
If sg_dma_len(sg)=0 we don't allocate for this sgl.
However in the next loop, we will increment loop
for this case, and loop gets higher than num_sgs
and we trample memory.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Newer versions of the DesignWare I2C block support the detection of
stuck signals, and a mechanism to recover from them. Add the required
software support to the driver.
This change was prompted by the observation that reading a single byte
from register 0 of a VEML7700 seems to cause it to issue an ACK too
early, and the controller to complain about losing arbitration. There
is a suspicion that this may be a more widespread problem, but at least
this patch prevents the bus from locking up.
See: https://github.com/raspberrypi/linux/issues/6057
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Recent Integral cards end up with corrupt sectors after a flash erase.
This covers sizes for the A2 range, which can't be differentiated from
the A1 range which might not have the same issue.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Only CMD38 with Arg=0x1 (Discard) is supported when in CQ mode, so
turn it off before issuing a non-discard erase op.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Cards with manufacture dates in 2019 and 2020 have been seen in the wild
that hang indefinitely if issued a cache flush command in CQ mode.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Samsung EVO Plus, Pro Plus and Evo Ultimate cards of this era appear to
have a broken cache-flush implementation when operating in CQ mode.
Unfortunately the cards seem to use a separate CID name string for every
variant and capacity, so nobble the cache feature for this MANFID, OEMID
and year. Turning this off seems to have negligible impact on
random-write throughput in non-CQ mode.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Posted write tracking introduced in the commit below raced with re-use
of the requests between completion and submission, potentially causing
underflow of the pending write count.
Fixes: e6c1e862b2 ("mmc: restrict posted write counts for SD cards in CQ mode")
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Command Queueing requires Write Cache and Power off Notification support
from the card - but using the write cache forms a contract with the host
whereby the card expects to be told about impending power-down.
The implication is that (for performance) the card can do unsafe things
with pending write data - including reordering what gets committed to
nonvolatile storage at what time.
Exposed SD slots and platforms powered by hotpluggable means (i.e.
Raspberry Pis) can't guarantee that surprise removal won't happen.
To limit the scope for cards to invent new ways to trash filesystems,
limit pending writes to 1 (equivalent to the non-CQ behaviour).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
fixup: mmc: restrict posted write counts for SD cards in CQ mode
Leaving card->max_posted_writes unintialised was a bad thing to do.
Also, cqe_enable is 1 if hsq is enabled as hsq substitutes the cqhci
implementation with its own.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Recovery claims the MMC card so the card-detect work gets significantly
delayed - leading to lots of error recovery loops that can never do
anything but fail.
Explicitly detect the card after CQE has halted and bail if it's not
there.
Also ratelimit a not-very-descriptive warning - one occurrence in dmesg
is enough to signal that something is amiss.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
If the controller is being reset, then the CQE needs to be reset as well.
For removable cards, CQHCI_SSC1 must specify a polling mode (CBC=0)
otherwise it's possible that the controller stops emitting periodic
CMD13s on card removal, without raising an error status interrupt.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
This gains about 8-12% sequential write speed with the fastest SD/eMMC
cards, and Class A1/A2 card sequential performance is only assured with
a 4MiB write length.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The attached PHY performs parameter validation, so the switch from HS200
to HS (before selecting HS400/HS400es) with a 200MHz clock fails to
update pad timings and results in CRC errors from the card.
Underclocking the interface is safe, so do that in the downgrade callback.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The spec allows for up to two 512-byte pages to be allocated for the
Extension Register General Info block, so allocate accordingly.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Don't attempt to turn on CQ if the other mandatory features are not
indicated as supported by the card. Also make sure that the register write
actually stuck, as some cards claim support but never report back that
the queue engine is enabled.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Certain status bits in these registers may need polling outside of
SD-specific code. Export in sd_ops.h
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The eMMC spec says that in certain circumstances the controller can't
respond to a halt request - in practice, this occurs if a CMD
timeout happens (card went away/crashed).
Clear the halt request by writing 0 to CQHCI_CTL. Also fix a logic error
testing for halt in cqhci_request.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
For unknown reasons the controller seems to reset the idle polling timer
interval on CQE enable/disable to 8 clocks which is extremely short.
Just use the reset value in the eMMC spec (4096 clock periods which at
200MHz is ~20uS).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Add a LED_FULL trigger equivalent to mmc_start_request() in
mmc_cqe_start_req(), otherwise it stays off forever.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The Performance Extension register is regularly accessed in a hot path
to do write cache flushes. Don't invoke kmalloc/kfree for every access,
preallocate a 512B buffer for this purpose.
Also remove an unused alloc in sd_enable_cache().
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Application class A2 cards require CQ to be enabled to realise their
stated performance figures. Add support to enable/disable card CQ via
the Performance Enhancement extension register, and cater for the slight
differences in command set versus eMMC.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Commit 7d239fbf9d broke 802.1X authentication by setting
profile->use_fwsup = NONE whenever PSK is not used. However
802.1X does not use PSK and requires profile->use_fwsup set
to 1X, or brcmf_cfg80211_set_pmk() fails. Fix this by checking
that profile->use_fwsup is not already set to 1X and avoid
setting it to NONE in that case.
Fixes: 7d239fbf9d (brcmfmac: Fix interoperating DPP and other encryption network access)
Fixes: https://github.com/raspberrypi/linux/issues/5964
1. If firmware supports 4-way handshake offload but not supports DPP
4-way offload, when user first connects encryption network, driver will
set "sup_wpa 1" to firmware, but it will further result in DPP
connection failure since firmware won't send EAPOL frame to host.
2. Fix DPP AP mode handling action frames.
3. For some firmware without fwsup support, the join procedure will be
skipped due to "sup_wpa" iovar returning not-support. Check the fwsup
feature before do such iovar.
Signed-off-by: Kurt Lee <kurt.lee@cypress.com>
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
In deep sleep mode (DS1) ARM is off and once exit trigger comes than
mailbox Interrupt comes to host and whole reinitiation should be done
in the ARM to start TX/RX.
Also fix below issus for DS1 exit:
1. Sent Tx Control frame only after firmware redownload complete (check
F2 Ready before sending Tx Control frame to Firmware)
2. intermittent High DS1 TX Exit latency time (almost 3sec) ==> This is
fixed by skipping host Mailbox interrupt Multiple times (ulp state
mechanism)
3. RX GlOM save/restore in Firmware
4. Add ULP event enable & event_msgs_ext iovar configuration in FMAC
5. Add ULP_EVENT_RECV state machine for sbwad support
6. Support 2 Byte Shared memory read for DS1 Exit HUDI implementation
Signed-off-by: Praveen Babu C <pucn@cypress.com>
Signed-off-by: Naveen Gupta <nagu@cypress.com>
[Merge from 4.14.77 to 5.4.18; set BRCMF_SDIO_MAX_ACCESS_ERRORS to 20]
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
JIRA: SWWLAN-135583
JIRA: SWWLAN-136577
i2c_mux_add_adapter takes a force_nr parameter that allows an explicit
bus number to be associated with a channel. However, only i2c-mux-reg
and i2c-mux-gpio make use of it.
To help with situations where it is desirable to have a fixed, known
base address for the channels of a mux, create a "base-nr" property.
When force_nr is 0 and base-nr is set and non-zero, form a force_nr
value from the sum of base-nr and the channel ID.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This patch adds the device ID for the BCM4343A2 module, found e.g. in
the Infineon (Cypress) CYW43439 chip. The required firmware file is
named 'BCM4343A2.hcd'.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
If enabled, DMA_BOUNCE_UNALIGNED_KMALLOC causes the swiotlb buffers
(64MB, by default) to be allocated, even on systems where the DMA
controller can reach all of RAM. This is a huge amount of RAM to
waste on a device with only 512MB to start with, such as the Zero 2 W.
See: https://github.com/raspberrypi/linux/issues/5975
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add support for non-standard bus speeds by treating them as detuned
versions of the slowest standard speed not less than the requested
speed.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Calculate the HCNT and LCNT values for all modes using the rise and
fall times of SCL, the aim being a 50/50 mark/space ratio.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
There are three parkmode disable bits, one for each bus instance type.
Add FS/LS and parse the quirk out of DT. Also update the slightly
mangled quirk descriptions.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
There are three disable bits, one for each bus-instance type. Add a
quirk to cover the FS/LS type, and update the slightly mangled quirk
descriptions in the process.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The forced conversion of native CS lines into software CS lines is done
whether or not the controller has been given any CS lines to use. This
breaks the use of the spi0-0cs overlay to prevent SPI from claiming any
CS lines, particularly with spidev which doesn't pass in the SPI_NO_CS
flag at creation.
Use the presence of an empty cs-gpios property as an indication that no
CS lines should be used, bypassing the native CS conversion code.
See: https://github.com/raspberrypi/linux/issues/5835
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
For CSI2 receivers that need to know the link frequency,
add it as a control to the driver.
Interlaced modes are 216Mbp/s or 108MHz, whilst going through
the I2P to deinterlace gives 432Mb/s or 216MHz.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
CSI2 devices are meant to use the 1Xnn formats rather than 2Xnn
such as MEDIA_BUS_FMT_UYVY8_2X8.
For devices with ADV7180_FLAG_MIPI_CSI2 set, use
MEDIA_BUS_FMT_UYVY8_1X16.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Pi 5 uses BL31 as its armstub file, so the reset goes via PSCI. Parse
any "reboot" parameter as a partition number to reboot into.
N.B. This code path is only used if reboot mode has been set to warm
or soft.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add support for the ROHM BU64754 Motor Driver for Camera Autofocus. A
V4L2 Subdevice is registered and provides a single
V4L2_CID_FOCUS_ABSOLUTE control.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Commit 7cd70656d1 ("drm/bridge: display-connector: implement
bus fmts callbacks") added use of drm_atomic_helper_bridge_*
functions, but didn't select the dependency of DRM_KMS_HELPER.
If nothing else selected that dependency it resulted in a
build failure.
Select the missing dependency.
Fixes: 7cd70656d1 ("drm/bridge: display-connector: implement bus fmts callbacks")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The mainline driver has implemented analogue gain using the control
V4L2_CID_GAIN instead of V4L2_CID_ANALOGUE_GAIN.
libcamera requires V4L2_CID_ANALOGUE_GAIN, and therefore fails.
Update the driver to use V4L2_CID_ANALOGUE_GAIN.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
event ring is drained by the kernel. Expand the number of event TRB slots
available by increasing the number of event ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, so make the actual number in use
min(ERST_MAX_SEGS, hw_max).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
With the new support for a chain of sys_off handlers, gpio-poweroff
does not disable a normal shutdown (though it does delay it). There
is therefore no need for the noisy WARN from the kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Certain controllers (dwc-mshc) generate timeout conditions separately to
command-completion conditions, where the end result is interrupts are
separated in time depending on the current SDCLK frequency.
This causes spurious interrupts if SDCLK is slow compared to the CPU's
ability to process and return from interrupt. This occurs during card
probe with an empty slot where all commands that would generate a
response time out.
Add a quirk to squelch command response interrupts when a command
timeout interrupt is received.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
For situations where there are multiple DRM cards in a system,
add a query of DT for "drm_fb" designations for cards to set
their preferred /dev/fbN designation.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/fb_helper: Change query for FB designation from drm_fb to drm-fb
Fixes: 1216ea56c2 ("drm/fb-helper: Look up preferred fbdev node number from DT")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a flag custom_fb_num to denote that the client has
requested a specific fbdev node number via node.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Vision Components have made an OV9281 module which blocks reading
back the majority of registers to comply with NDAs, and in doing
so doesn't allow auto-increment register reading as used when
reading the chip ID.
Use two reads and manually combine the results.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add binding for the new RTC driver for Raspberry Pi.
This platform has an RTC managed by firmware, and this RTC
driver provides the simple mailbox interface to access it.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
dt: bindings: update rpi-rtc binding
Add property for bcm2712 firmware RTC driver charger control
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
This supports setting and reading the real time clock
and supports wakeup alarms.
To support wake up alarms you want this bootloader config:
POWER_OFF_ON_HALT=1
WAKE_ON_GPIO=0
You can test with:
echo +600 | sudo tee /sys/class/rtc/rtc0/wakealarm
sudo halt
That will halt (in an almost no power state),
then wake and restart after 10 minutes.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
drivers: rtc-rpi: add battery charge circuit control and readback
Parse devicetree for a charger voltage and apply it. If nonzero and a
valid voltage, the firmware will enable charging, otherwise the charger
circuit is disabled.
Add sysfs attributes to read back the supported charge voltage range,
the measured battery voltage, and the charger setpoint.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
We currently see these regularly:
[ 25.157560] irq 31, desc: 00000000c15e6d2c, depth: 0, count: 0, unhandled: 0
[ 25.164658] ->handle_irq(): 00000000b1775675, brcmstb_l2_intc_irq_handle+0x0/0x1a8
[ 25.172352] ->irq_data.chip(): 00000000fea59f1c, gic_chip_mode1+0x0/0x108
[ 25.179166] ->action(): 000000003eda6d6f
[ 25.183096] ->action->handler(): 000000002c09e646, bad_chained_irq+0x0/0x58
[ 25.190084] IRQ_LEVEL set
[ 25.193142] IRQ_NOPROBE set
[ 25.196198] IRQ_NOREQUEST set
[ 25.199255] IRQ_NOTHREAD set
with:
$ cat /proc/interrupts | grep 31:
31: 1 0 0 0 GICv2 129 Level (null)
The interrupt is described in DT with IRQ_TYPE_LEVEL_HIGH
But the current compatible string uses the controller in edge triggered mode
(as that config matches our register layout).
Add a new compatible structure for level driven interrupt with our register layout.
We had already been using this compatible string in device tree, so no change needed
there.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Add a driver for BCM2712 IOMMUs.
There is a small driver for the Shared IOMMU TLB Cache.
Each IOMMU instance is a separate device.
IOMMUs are set up with a "pass-through" range covering
the lowest 40BGytes (which should cover all of SDRAM)
for the benefit of non-IOMMU-aware devices that share
a physical IOMMU; and translation for addresses in the
range 40GB to 42GB.
An optional parameter adds a DMA offset (which otherwise
would be lost?) to virtual addresses for DMA masters on a
bus such as PCIe.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
iommu: bcm2712-iommu: Map and unmap multiple pages in a single call
For efficiency, the map_pages() and unmap_pages() calls now pay
attention to their "count" argument.
Remove a special case for a "pass-through" address range, which
the DMA/IOMMU subsystem isn't told exists and should never use.
Fix a bug where we omitted to set *mapped to 0 in error cases.
Minor style fixes and tidying.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
iommu/bcm2712: don't allow building as module
Since bcm2712-iommu{,-cache}.c doesn't have usual module descriptors
such as `MODULE_LICENSE`, configuring this as 'M' fails the build with
`ERROR: modpost: missing MODULE_LICENSE() in <...>/bcm2712-iommu.o`.
Since it seems like the code is not intended to be built as a module
anyway (it registers the driver with `builtin_platform_driver()`), don't
allow building this code as a module.
Signed-off-by: Ratchanan Srirattanamet <peathot@hotmail.com>
iommu: bcm2712-iommu: Add locking; fix address offset; tidy
- Now using spin_lock_irqsave in map, unmap, sync and iova_to_phys.
- Simplify bounds checks as all allocations should be in aperture.
- Use iommu_iotlb_gather_add_range(); NB gather range is inclusive.
- Fix missing address offset in bcm2712_iommu_sync_all.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
iommu: bcm2712-iommu: Allocate tables on demand; add OF properties
Allocate space for level-2 IOMMU translation tables on demand.
This should save memory in most cases but means that map_pages()
can now fail with -ENOMEM. Unused pages are retained for re-use.
Move all dma_sync* calls into map and unmap functions rather than
batching them up. This makes it easier to ensure they are safely
balanced, now that the tables are held as separate pages.
Add OF properties to override the default aperture size (2GB)
and base address (40GB); this doesn't include any dma-iova-offset.
Various tidy-ups. The internal representation of aperture limits
*does* include dma_iova_offset, as that is more commonly useful.
Clarify the distinction between Linux pages and IOMMU table pages.
Fix wrong definition of MMMU_CTRL_PT_INVALID_EN flag.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
The BCM2712 has a DMA-Lite controller that is basically a BCM2835-style
DMA controller that supports 40 bits DMA addresses.
We need it for HDMI audio to work, but this breaks BCM2835-38 so we
should rework this later.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
dmaengine: bcm2835: Fix dma driver for BCM2835-38
The previous commit broke support on older devices.
Make the breaking parts of patch conditional on
the device being used.
Fixes: 6e1856ac7c39 ("dmaengine: bcm2835: HACK: Support DMA-Lite channels")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
BCM2712 has 6 40-bit channels - DMA6 to DMA11. Add a new compatible
string to indicate that the current platform is BCM2712.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Formerly the delay was omitted as bit-banged SPI seldom achieved
even one Mbit/s; but some modern platforms can run faster, and
some SPI devices may need to be clocked slower.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Formerly, if configured using DT, CS GPIOs were driven from spi.c
and it was possible for CS to be asserted (low) *before* starting
to drive SCK. CS GPIOs have been brought under control of this
driver in both ACPI and DT cases, with a fixup for GPIO polarity.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
BCM2712 has a PM block but neither ASB nor RPIVID_ASB. Use the absence
of the "asb" register range to indicate BCM2712 and its different PM
register range.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
BCM2712 lacks the "asb" and "rpivid_asb" register ranges, but still
requires the use of the bcm2835-power driver to reset the V3D block.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
drivers: hwmon: rp1-adc: check conversion validity before supplying value
The SAR ADC architecture may complete a conversion but instability in the
comparator can corrupt the result. Such corruption is signalled in the CS
ERR bit, asserted alongside each conversion result.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Add optional properties to tune the AXI interface -
cdns,aw2w-max-pipe, cdns,ar2r-max-pipe and cdns,use-aw2b-fill.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This supports reading and writing OTP using the firmware
mailbox interface.
It needs supporting firmware to run.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Add support for the RP1 VEC hardware.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm: rp1: rp1-vec: Allow non-standard modes with various crops
Tweak sync timings in the advertised modelines.
Accept other, custom modes, provided they fit within the active
area of one of the existing hardware-supported TV modes.
Instead of always padding symmetrically, try to respect the user's
[hv]sync_start values, allowing the image to be shifted around
the screen (to fine-tune overscan correction).
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm/rp1: depends on, instead of select, MFD_RP1
According to kconfig-language.txt [1], select should be used only for
"non-visible symbols ... and for symbols with no dependencies". Since
MFD_RP1 both is visible and has a dependency, "select" should not be
used and "depends on" should be used instead.
In particular, this fixes the build of this kernel tree on NixOS, where
its kernel config system will try to answer 'M' to as many config as
possible.
[1] https://www.kernel.org/doc/html/latest/kbuild/kconfig-language.html
Signed-off-by: Ratchanan Srirattanamet <peathot@hotmail.com>
drm: rp1: Use tv_mode from the command line and fix for Linux 6.6
Use the standard enum drm_connector_tv_mode instead of a private
enum and switch from the legacy to the standard tv_mode property.
Remove the module parameter "tv_norm". Instead, get tv_mode from
the command line and make this the connector's default TV mode.
Don't restrict the choice of modes based on tv_mode, but interpret
nonstandard combinations as NTSC or PAL, depending on resolution.
Thus the default tv_mode=NTSC effectively means "Auto".
Tweak the advertised horizontal timings for 625/50 to match Rec.601
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm: rp1: VEC and DPI drivers: Fix bug #5901
Rework probe() to use devm_drm_dev_alloc(), embedding the DRM
device in the DPI or VEC device as now seems to be recommended.
Change order of resource allocation and driver initialization.
This prevents it trying to write to an unmapped register during
clean-up, which previously could crash.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm: rp1: vec: Support more video modes in the RP1 VEC driver
Support a wider range of pixel clock rates. The driver will round
pixclock up to 108MHz/n but tries to honour the desired image width
and position (of the centre of the display relative to HSYNC_STARTs).
This adds complexity but removes the need for separate 13.5MHz and
15.428MHz modes.
Support "fake" double-rate progressive modes (in which only every
2nd scanline is displayed). To work around aspect ratio issues.
Add Monochrome TV mode support. Add "vintage" modes (544x380i for
System A; 848x738i for System E) when configured for Monochrome.
Add a way to create a "custom" display mode from a module parameter.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm: rp1: rp1-vec: Add DRM_FORMAT_ARGB8888 and DRM_FORMAT_ABGR8888
Android requires this.
As the underlying hardware doesn't support alpha blending,
we ignore the alpha value.
Signed-off-by: Jan Kehren <jan.kehren@emteria.com>
drivers: drm: rp1-vec: Increase width limit, for PAL 16:9 @ 18MHz
There was no technical reason for the DRM mode's width limit of 848;
increase it to 960 (720*18MHz/13.5MHz) to support ~square pixels on
16:9 screens. Tweak the PAL active window to start slightly earlier.
(The maximum number of visible columns at 18MHz is about 942.)
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm/vc4: Make VEC progressive modes readily accessible
Add predefined modelines for the 240p (NTSC) and 288p (PAL) progressive
modes, and report them through vc4_vec_connector_get_modes().
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
drm/rp1-vec: Run DRM default client setup
Call drm_client_setup() to run the kernel's default client setup
for DRM. Set fbdev_probe in struct drm_driver, so that the client
setup can start the common fbdev client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm: rp1: Enable VEC->GPIO output; cosmetic change to registers
In the VEC driver, enable mapping VEC (not DPI) to DPI GPIOs.
This is to support VEC output over GPIO on Raspberry Pi CM5.
It is harmless as DPI and VEC could not be used concurrently,
and the output is anyway conditional on pinctrl.
Also, tweak the style of VIDEO_OUT_CFG register definitions
(in both DPI and VEC drivers) to be more Linux-friendly.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm: rp1: rp1-vec: Support 60fps in interlaced modes; other tweaks
To work around the 30fps buffer-flip rate limit when using VEC's
"native" interlaced modes, switch to sending individual fields
to the VEC BE, using an ISR to flip between fields.
When the TV mode is NTSC, change advertised progressive modes to
have 263 total lines; this ameliorates colour artifacts, although
it reduces the frame rate slightly from 60.05Hz to 59.83Hz.
Progressive modes with 262 lines remain supported.
Fix an error in equalising pulse configuration for PAL-M/PAL60.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Add support for the RP1 DPI hardware.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm/rp1: depends on, instead of select, MFD_RP1
According to kconfig-language.txt [1], select should be used only for
"non-visible symbols ... and for symbols with no dependencies". Since
MFD_RP1 both is visible and has a dependency, "select" should not be
used and "depends on" should be used instead.
In particular, this fixes the build of this kernel tree on NixOS, where
its kernel config system will try to answer 'M' to as many config as
possible.
[1] https://www.kernel.org/doc/html/latest/kbuild/kconfig-language.html
Signed-off-by: Ratchanan Srirattanamet <peathot@hotmail.com>
drm: rp1: VEC and DPI drivers: Fix bug #5901
Rework probe() to use devm_drm_dev_alloc(), embedding the DRM
device in the DPI or VEC device as now seems to be recommended.
Change order of resource allocation and driver initialization.
This prevents it trying to write to an unmapped register during
clean-up, which previously could crash.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm: rp1: dpi: Add support for MEDIA_BUS_FMT_RGB565_1X24_CPADHI
This new format corresponds to the Raspberry Pi legacy DPI mode 3.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm: rp1: rp1-dpi: Add DRM_FORMAT_ARGB8888 and DRM_FORMAT_ABGR8888
Android requires this.
As the underlying hardware doesn't support alpha blending,
we ignore the alpha value.
Signed-off-by: Jan Kehren <jan.kehren@emteria.com>
drm: rp1: rp1-dpi: Add interlaced modes and PIO program to fix VSYNC
Implement interlaced modes by wobbling the base pointer and VFP width
for every field. This results in correct pixels but incorrect VSYNC.
Now use PIO to generate a fixed-up VSYNC by sampling DE and HSYNC.
This requires DPI's DE output to be mapped to GPIO1, which we check.
When DE is not exposed, the internal fixup is disabled. VSYNC/GPIO2
becomes a modified signal, designed to help an external device or
PIO program synthesize CSYNC or VSYNC.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm: rp1: rp1-dpi: Fix optional dependency on RP1_PIO
Add optional dependency to Kconfig, and conditionally compile
PIO-dependent code. Add a mode validation function to reject
interlaced modes when RP1_PIO is not present.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm: rp1: rp1-dpi: Add "rgb_order" property (to match VC4 DPI)
As on VC4, the OF property overrides the order implied by media
bus format. Only 4 of the 6 possible orders are supported. New
add-on hardware designs should not rely on this "legacy" feature.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm/rp1: DPI interlace: Improve precision of PIO-generated VSYNC
Instead of trying to minimize the delay between seeing HSYNC edge
and asserting VSYNC, try to predict the next HSYNC edge precisely.
This eliminates the round-trip delay but introduces mode-dependent
rounding error. HSYNC->VSYNC lag reduced from ~30ns to -5ns..+10ns
(plus up to 5ns synchronization jitter as before).
This may benefit e.g. SCART HATs, particularly those that generate
Composite Sync using a XNOR gate.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm/rp1-dpi: Run DRM default client setup
Call drm_client_setup() to run the kernel's default client setup
for DRM. Set fbdev_probe in struct drm_driver, so that the client
setup can start the common fbdev client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/rp1/rp1_dpi: Move Composite Sync generation into the kernel
Move RP1 DPI's PIO-assisted Composite Sync generation code,
previously released as a separate utility, into the kernel driver.
There are 3 variants for progressive, generic interlaced and TV-
style interlaced CSync, alongside the existing VSync fixup.
Check that all of GPIOs 1-3 are mapped to DPI, so PIO won't try
to snoop on a missing output, or override another device's pins.
Add "force_csync" module parameter, for convenience of testing,
as few tools can set DRM_MODE_FLAG_CSYNC.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
drm: rp1: Enable VEC->GPIO output; cosmetic change to registers
In the VEC driver, enable mapping VEC (not DPI) to DPI GPIOs.
This is to support VEC output over GPIO on Raspberry Pi CM5.
It is harmless as DPI and VEC could not be used concurrently,
and the output is anyway conditional on pinctrl.
Also, tweak the style of VIDEO_OUT_CFG register definitions
(in both DPI and VEC drivers) to be more Linux-friendly.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Add support for the RP1 DSI hardware.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm/rp1: depends on, instead of select, MFD_RP1
According to kconfig-language.txt [1], select should be used only for
"non-visible symbols ... and for symbols with no dependencies". Since
MFD_RP1 both is visible and has a dependency, "select" should not be
used and "depends on" should be used instead.
In particular, this fixes the build of this kernel tree on NixOS, where
its kernel config system will try to answer 'M' to as many config as
possible.
[1] https://www.kernel.org/doc/html/latest/kbuild/kconfig-language.html
Signed-off-by: Ratchanan Srirattanamet <peathot@hotmail.com>
DRM: rp1: rp1-dsi: Fix escape clock divider and timeouts.
Escape clock divider was fixed at 5, which is correct at 800Mbps/lane
but increasingly out of spec for higher rates. Compute it correctly.
High speed timeout was fixed at 5*512 == 2560 byte-clocks per lane.
Compute it conservatively to be 8/7 times the line period (assuming
there will be a transition to LP some time during each scanline?)
keeping the old value as a lower bound. Increase LPRX TO to 1024,
and BTA TO to 0xb00 (same value as in bridge/synopsys/dw-mipi-dsi).
(No change to LP_CMD_TIM. To do: compute this correctly.)
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm: rp1: rp1-dsi: Switch to PLL_SYS source for DPI when 8 * lanes > bpp
To support 4 lanes, re-parent DPI clock source between DSI byteclock
(using the new "variable sources" defined in clk-rp1) and PLL_SYS.
This is to cover cases in which byteclock < pixclock <= 200MHz.
Tidying: All frequencies now in Hz (not kHz), where DSI speed is now
represented by byteclock to simplify arithmetic. Clamp DPI and byte
clocks to their legal ranges; fix up HSTX timeout to avoid an unsafe
assumption that it would return to LP state for every scanline.
Because of RP1's clock topology, the ratio between DSI and DPI clocks
may not be exact with 3 or 4 lanes, leading to slightly irregular
timings each time DSI switches between HS and LP states. Tweak to
inhibit LP during Horizontal BP when sync pulses were requested.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm: rp1: rp1-dsi: Add DRM_FORMAT_ARGB8888 and DRM_FORMAT_ABGR8888
Android requires this.
As the underlying hardware doesn't support alpha blending,
we ignore the alpha value.
Signed-off-by: Jan Kehren <jan.kehren@emteria.com>
drivers: drm: rp1-dsi: Implement more DSI options and flags
Now implementing:
- Per-command selection of LP or HS for commands (previously LP)
- EoTp transmission option (previously EoTp was always disabled)
- Non-continuous clock option (previously always continuous)
- Per-command enabling of ACK request (in command mode only)
Make a plausible (and possibly correct) attempt to measure the
longest LP command that will fit into vertical blanking lines.
DON'T set both "Burst Mode" and "Sync Events" flags together.
This is redundant in the standard IP; in this RP1 variant it
would enable Sync Pulses but may break with some video timings.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drm/rp1-dsi: Run DRM default client setup
Call drm_client_setup() to run the kernel's default client setup
for DRM. Set fbdev_probe in struct drm_driver, so that the client
setup can start the common fbdev client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/rp1: rp1-dsi: Put all register defines into order
Put particularly the PHY registers into order, bitmasks
defined alongside the registers, and Use tabs for indentation.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/rp1: rp1-dsi: Remove all the unused boilerplate register defines
There was lots of register definition information dumped from
the some source into the driver but unused. Remove it, and
format the remaining lines according to the Linux kernel coding
style.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/rp1: rp1-dsi: Add support for inverting lane polarities
The D-PHY on RP1 support lane polarity swapping, and there
is a standard device tree mechanism for configuring this,
so tie the two together.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Don't assume that DMA addresses of devices are the same as their
physical addresses - convert correctly.
The CFG2 register layout is used when there are more than 8 channels,
but also when configured for more than 16 target peripheral devices
because the index of the handshake signal has to be made wider.
Reset the DMAC on probe
The driver goes to the trouble of tracking when transfers have been
paused, but then doesn't report that state when queried.
Not having APB registers is not an error - for most use cases it's
not even of interest, it's expected. Demote the message to debug level,
which is disabled by default.
Each channel has a descriptor pool, which is shared between transfers.
It is unsafe to treat the total number of descriptors allocated from a
pool as the number allocated to a specific transfer; doing so leads
to releasing buffers that shouldn't be released and walking off the
ends of descriptor lists. Instead, give each transfer descriptor its
own count.
Support partial transfers:
Some use cases involve streaming from a device where the transfer only
proceeds when the device's FIFO occupancy exceeds a certain threshold.
In such cases (e.g. when pulling data from a UART) it is important to
know how much data has been transferred so far, in order that remaining
bytes can be read from the FIFO directly by software.
Add the necessary code to provide this "residue" value with a finer,
sub-transfer granularity.
In order to prevent the occasional byte getting stuck in the DMA
controller's internal buffers, restrict the destination memory width
to the source register width.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
dmaengine: dw-axi-dmac: Fix a non-atomic update
dw_axi_dma_interrupt disables interrupts for the duration of the channel
handling. It does so by clearing a bit in the DMA_CFG register - an
action that involves a read-modify-write. That in itself would be safe
because there will be no further interrupts, hence no reentrancy, were
it the only bit of code accessing that register.
The only neighbour of INT_EN is DMAC_EN - the main enable for the block.
That's not the sort of thing you would expect to be modified during the
normal course of operation, but bizarrely it is set at the start of the
transfer of every block, in axi_chan_block_xfer_star, by a call to
axi_dma_enable. This can lead to INT_EN being accidentally cleared,
which causes all DMA transfers to time out.
One might think that the enabling was being delayed until the first
transfer, but the probe function calls axi_dma_resume which in turn
calls axi_dma_enable, so that isn't the case.
Fix the atomicity problem by removing the spurious call to
axi_dma_enable.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The SMBUS emulation code turns an SMBUS quick command into a zero-
length read. This controller can't do zero length accesses, but it
can do quick commands, so reverse the emulation. The alternative
would be to properly implement the SMBUS support but that is a lot
more work, and unnecessary just to get i2cdetect working.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Liam Fraser <liam@raspberrypi.com>
mmc: sdhci-of-dwcmshc: rp1 sdio changes
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
drivers: mmc: sdhci-of-dwcmshc: add RP1 dt ID and quirks
Differentiate the RP1 variant of the Designware MSHC controller(s).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ARM: pl011: Add rs485 to the RP1 support
pl011_axi_probe, added for RP1 support, lacks the rs485 additions that
appeared during its development.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
tty/serial: pl011: restrict RX burst FIFO threshold
If the associated DMA controller has lower burst length support than the
level the FIFO is set to, then bytes will be left in the RX FIFO at the
end of a DMA block - requiring a round-trip through the timeout interrupt
handler rather than an end-of-block DMA interrupt.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
tty/serial: pl011: Also unregister pl011_axi_platform_driver
See: https://github.com/raspberrypi/linux/issues/6379
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
RP1 is a multifunction PCIe device that exposes a range of
peripherals.
Add the parent driver to manage these.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
mfd: rp1: Support interrupt CPU affinity
See: https://github.com/raspberrypi/linux/issues/6077
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
pinctrl: rp1: Allow building as a module
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
mfd: rp1: depends on PCI_MSI
The driver uses pci_msi methods, only defined when CONFIG_PCI_MSI symbol
is set, and cannot be compiled without. Therefore, it depends on this
symbol.
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
mfd: rp1: Fix device links when modules disabled
Device links are used to keep track of suppliers and consumers of
resources, adding some control over the ordering of device probes other
than returning -EPROBE_DEFER. The way the RP1 device is created breaks
this mechanism in the rare case that the use of modules has been
completely disabled, thanks to some opimisations within the device link
code.
Fix this glitch by giving the corresponding fwnode a pointer to the
device, taking the opportunity to remove a pointless check on the
validity of the rp1_node pointer.
See: https://github.com/raspberrypi/linux/issues/7018
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
dwc3 allocates scratch and event buffers in the top-level driver. Hack the
probe function to set the DMA mask before trying to allocate these.
I think the event buffers are only used in device mode, but the scratch
buffers may be used if core hibernation is enabled.
usb: dwc3: add support for new DT quirks
Apply the optional axi-pipe-limit and dis-in-autoretry-quirk properties
during driver probe.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
phy: phy-brcm-usb: Add 2712 support
usb: dwc3: if the host controller instance number is present in DT, use it
If two instances of a dwc3 host controller are specified in devicetree,
then the probe order may be arbitrary which results in the device names
swapping on a per-boot basis.
If a "usb" alias with the instance number is specified, then use
that to construct the device name instead of autogenerating one.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
rp1 dwc3 changes
drivers: usb: dwc3: allow setting GTXTHRCFG on dwc_usb3.0 hardware
Equivalent register fields exist in the SuperSpeed Host version of the
hardware, so allow the use of TX thresholds if specified in devicetree.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: usb: dwc3: remove downstream quirk dis-in-autoretry
Upstream have unilaterally disabled the feature.
Partially reverts 6e9142a26ee0fdc3a5adc49ed6cedc0b16ec2ed1 (downstream)
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
macb: Add device tree properties that allow configuration of the AXI max pipeline register
net: macb: add support for ethtool interrupt moderation configuration
Only global throttling of rx or tx by time quanta is supported.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
macb: add platform device shutdown function. Prevents AXI master over PCIE from hanging when the host is rebooted.
net: macb: increase polling interval for MDIO completion
MDIO is a slow bus (single-digit MHz). Polling at 1us intervals
is a bit aggressive, so increase to 100us as the transaction
usually takes 100-200us to complete.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
net: macb: Several patches for RP1
64-bit RX fix
Also set DMA coherent mask
Add device tree properties that allow configuration of the AXI max
pipeline register
Add support for ethtool interrupt moderation configuration
Only global throttling of rx or tx by time quanta is supported.
Add platform device shutdown function. Prevents AXI master over PCIE
from hanging when the host is rebooted.
Increase polling interval for MDIO completion
MDIO is a slow bus (single-digit MHz). Polling at 1us intervals
is a bit aggressive, so increase to 100us as the transaction
usually takes 100-200us to complete.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
net: macb: Support the phy-reset-gpios property
Allow a PHY to be reset with an optional GPIO. The reset duration can
be specified in milliseconds - the default is 10ms.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
drivers: net: macb: close device on driver shutdown
Fix some suspicious locking and instead call into macb_close, which
deregisters and frees all resources the corresponding macb_open
claimed.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
net: macb: add hack to prevent TX stalls in a quiet system
See https://github.com/raspberrypi/linux-2712/issues/89
There is some critical window during TX where a further write to the
TSTART bit while TX is active does not cause newly queued TX descriptors
to be consumed.
For now "wait a bit, then try anyway" seems to work.
Requires further investigation, but this unsticks NFS reliably.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
net: macb: set default interrupt moderation for GEM hardware
Defaulting to intmod = 0 is antisocial, as the MAC can generate over
130,000 interrupts per second. 50us is a sensible default.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
reset_control_reset should not be used with shared reset controllers.
Add support for reset_control_assert and _deassert to get the desired
behaviour and avoid ugly warnings in the kernel log.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
BCM2712 has an SD Express capable SDHCI implementation and uses
the SDIO CFG register block present on other STB chips.
Add plumbing for SD Express handover and BCM2712-specific functions.
Due to the common bus infrastructure between BCM2711 and BCM2712,
the driver also needs to implement 32-bit IO accessors.
mmc: brcmstb: override card presence if broken-cd is set
Not just if the card is declared as nonremovable.
sdhci: brcmstb: align SD express switchover with SD spec v8.00
Part 1 of the Physical specification, figure 3-24, details the switch
sequence for cards initially probed as SD. Add a missing check for DAT2
level after switching VDD2 on.
sdhci: brcmstb: clean up SD Express probe and error handling
Refactor to avoid spurious error messages in dmesg if the requisite SD
Express DT nodes aren't present.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
mmc: sdhci-brcmstb: only use the delay line PHY for tuneable speeds
The MMC core has a 200MHz core clock which allows the use of DDR50 and
below without incremental phase tuning. SDR50/SDR104 and the EMMC HS200
speeds require tuning.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
mmc: sdhci-brcmstb: remove 32-bit accessors for BCM2712
The reason for adding these are lost to the mists of time (and for a
previous chip revision). Removing these accessors appears to have no ill
effect on production chips, so get rid of the unnecessary RMW cycles.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: mmc: sdhci-brcmstb: fix usage of SD_PIN_SEL on BCM2712
The SDIO_CFG register SD_PIN_SEL conflates two settings - whether eMMC
HS or SD UHS timings are applied to the interface, and whether or not
the card-detect line is functional. SD_PIN_SEL can only be changed when
the SD clock isn't running, so add a bcm2712-specific clock setup.
Toggling SD_PIN_SEL at runtime means the integrated card-detect feature
can't be used, so this controller needs a cd-gpios property.
Also fix conditionals for usage of the delay-line PHY - no-1-8-v will
imply no bits set in hsemmc_mask or uhs_mask, so remove it.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: sdhci-brcmstb: set CQE timer clock frequency
CQHCI keeps track of tags in flight with internal timers, so the clock
frequency driving the timer needs to be specified. The config registers
default to 0 (100kHz) which means timeouts will be significantly shorter
than they should be. Assume the timer clock comes from the controller
base clock.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
gpio-brcmstb: Report the correct bank width
gpio: brcmstb: Use bank address as gpiochip label
If the path to the device node is used as gpiochip label then
gpio-brcmstb instances with multiple banks end up with duplicated
names. Instead, use a combination of the driver name with the physical
address of the bank, which is both unique and helpful for devmem
debugging.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio: mmio: Add DIRECT mode for shared access
The generic MMIO GPIO library uses shadow registers for efficiency,
but this breaks attempts by raspi-gpio to change other GPIOs in the
same bank. Add a DIRECT mode that makes fewer assumptions about the
existing register contents, but note that genuinely simultaneous
accesses are likely to lose updates.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio: brcmstb: Don't always clear interrupt mask
If the GPIO controller is not being used as an interrupt source
leave the interrupt mask register alone. On BCM2712 it might be used
to generate interrupts to the VPU firmware, and on other devices it
doesn't matter since no interrupts will be generated.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio: brcmstb: Use dynamic GPIO base numbers
Forcing a gpiochip to have a fixed base number now leads to a warning
message. Remove the need to do so by calculating hwirq numbers based
on bank numbers.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Fixes: 3b0213d56e ("gpio: Add GPIO support for Broadcom STB SoCs")
For "Really Good Reasons" [1] the SPI core requires a match
between compatible device strings and the name in spi_device_id.
The ili9486 driver uses compatible strings "waveshare,rpi-lcd-35"
and "ozzmaker,piscreen", but "rpi-lcd-35" and "piscreen" are missing,
so add them.
Compatible string "ilitek,ili9486" is already used by
staging/fbtft/fb_ili9486, therefore leaving it present in ili9486 as an
spi_device_id causes the incorrect module to be loaded, therefore remove
this id.
[1] https://elixir.bootlin.com/linux/latest/source/drivers/spi/spi.c#L487
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Loading the regulatory database from the debian files fails with
"loaded regulatory.db is malformed or signature is missing/invalid"
due to missing certificates. Add these debian-specific certificates
from upstream to fix this error. See #5536 for details.
The certificates have been imported as following:
patch -p1 <<<$(
curl https://salsa.debian.org/kernel-team/linux/-/raw/\
master/debian/patches/debian/\
wireless-add-debian-wireless-regdb-certificates.patch
)
Signed-off-by: Nicolai Buchwitz <n.buchwitz@kunbus.com>
The integrated USB2.0 hub in the VL805 chipset has a bug where it
incorrectly determines the remaining available frame time before the
host next sends a SOF packet with an incremented frame_number.
See the USB2.0 specification sections 11.3 and 11.14.2.3.
The hub's non-periodic TT handler can transmit the IN/OUT handshake
token too late, so a following 64-byte DATA0/1 packet causes the ACK
handshake to collide with the propagated SOF. This causes port babble.
Avoid ringing doorbells for vulnerable endpoints during uFrame 7 if the
TR is Idle to stop one source of babble. An IN transfer for a Running TR
may happen at any time, so there's not much we can do about that.
Ideally a hub firmware update to properly implement frame timeouts is
needed, and to avoid spinning for up to 125us when submitting TDs to
Idle rings.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
xhci: constrain XHCI_VLI_HUB_TT_QUIRK to old firmware versions
VLI have a firmware update for the VL805 which resolves the incorrect
frame time calculation in the hub's TT. Limit applying the quirk to
known-bad firmwares.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The VL805 can cause data corruption if a SS Bulk OUT endpoint enters a
flow-control condition and there are TRBs in the transfer ring that are
not an integral size of wMaxPacket and the endpoint is behind one or more
hubs.
This is frequently the case encountered when FAT32 filesystems are
present on mass-storage devices with cluster sizes of 1 sector, and the
filesystem is being written to with an aggregate of small files.
The initial implementation of this quirk separated TRBs that didn't
adhere to this limitation into two - the first a multiple of wMaxPacket
and the second the 512-byte remainder - in an attempt to force TD
fragments to align with packet boundaries. This reduced the incidence
rate of data corruption but did not resolve it.
The fix as recommended by VIA is to disable bursts if this sequence of
TRBs can occur.
Limit turning off bursts to just USB mass-storage devices by searching
the device's configuration for an interface with a class type of
USB_CLASS_MASS_STORAGE.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The VL805 controller can't cope with the TR Dequeue Pointer for an endpoint
being set to a Link TRB. The hardware-maintained endpoint context ends up
stuck at the address of the Link TRB, leading to erroneous ring expansion
events whenever the enqueue pointer wraps to the dequeue position.
If the search for the end of the current TD and ring cycle state lands on
a Link TRB, move to the next segment.
Link: https://github.com/raspberrypi/linux/issues/3919
[6.5.y Fixup - move downstream quirk bits further along]
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
As of [1], using PPS_FETCH on a 64-bit ARM kernel with a 32-bit userland
is broken, returning a timeout. This is because the requested 4-byte
alignment for struct pps_ktime_compat (illegal on arm64) results in the
timeout flags field being uninitialised.
Make the hack specific to X86_64 builds with CONFIG_COMPAT defined.
[1] commit c2a49fe8ee ("pps: fix padding issue with PPS_FETCH for
ioctl_compat")
See: https://github.com/raspberrypi/linux/issues/5430
Fixes: c2a49fe8ee ("pps: fix padding issue with PPS_FETCH for ioctl_compat")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
It has been observed that edge events can be lost when GPIO edges occur
close to each other. Investigation suggests this is due to a hardware
bug, although no mechanism has been identified.
Work around the event loss by moving the IRQ acknowledgement into the
main ISR, adding missing events by explicit level-change detection.
See: https://forums.raspberrypi.com/viewtopic.php?t=350295
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The kernel needs to recognise the default BDADDRs used by the Bluetooth
modems, so add a few more that we care about.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The kernel Bluetooth framework understands that devices may not
be programmed with valid Bluetooth addresses. It also has the ability
to override a Bluetooth address with the value of the local-bd-address
DT property, but it ignores the validity of the existing address when
doing so.
Add a new boolean property, fallback-bd-address, which indicates that
the given local-bd-address property should only be used if the device
does not already have a valid BDADDR.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The BCM2835 mini-UART has no modem status interrupt, causing all
transmission to stop, never to use, if a speed change ever happens
while the CTS signal is high.
Add a simple polling mechanism in order to allow recovery in that
situation.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Since [1], the fbdev deferred IO framework is careful to cancel
pending updates on close to prevent dirty pages being accessed after
they may have been reused. However, this is not necessary in the case
that the pagelist is empty, and drivers that don't make use of the
pagelist may have wanted updates cancelled for no good reason.
Avoid penalising fbdev drivers that don't make use of the pagelist by
making the cancelling of deferred IO on close conditional on there
being a non-empty pagelist.
See: https://github.com/raspberrypi/linux/issues/5398
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 3efc61d952 ("fbdev: Fix invalid page access after closing deferred I/O devices")
While waiting for random data, use sleeps that are proportional
to the amount of data expected. Prevent indefinite waits by
giving up if nothing is received for a second.
See: https://github.com/raspberrypi/linux/issues/5390
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The imx708 is a 12MP MIPI sensor with a 16:9 aspect ratio, here using
two CSI-2 lanes. It is a "quad Bayer" sensor with all 3 modes offering
10-bit output:
12MP: 4608x2592 up to 14.35fps (full FoV)
1080p: 2304x1296 up to 56.02fps (full FoV)
720p: 1536x864 up to 120.12fps (cropped)
This imx708 sensor driver is based heavily on the imx477 driver and
has been tested on the Raspberry Pi platform using libcamera.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drivers: media: imx708: Enable long exposure mode
Enable long exposure modes by using the long exposure shift register setting
in the imx708 sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: i2c: imx708: Fix crop information
The 1536x864 mode contained incorrect crop information.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
drivers: media: i2c: imx708: Fix WIDE_DYNAMIC_RANGE control with long exposure
Setting V4L2_CID_WIDE_DYNAMIC_RANGE was causing the long exposure
shift count to be reset, which is incorrect if the user has already
changed the frame length to cause it to have a non-zero value.
Because it only updates control ranges and doesn't set any registers,
the control can also be applied when the sensor is not powered on.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
drivers: media: imx708: Increase usable link frequencies
Add support for three different usable link frequencies (default 450Mhz,
447Mhz, and 453MHz) for the IMX708 camera sensor. The choice of
frequency is handled thorugh the "link-frequency" overlay parameter.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: imx708: Remove unused control fields
Remove unused and redundant control fields from the state structure.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: imx708: Tidy-ups to address upstream review comments
This commit addresses vaious tidy-ups requesed for upstreaming the
IMX708 driver. Notably:
- Remove #define IMX708_NUM_SUPPLIES and use ARRAY_SIZE() directly
- Use dev_err_probe where possible in imx708_probe()
- Fix error handling paths in imx708_probe()
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: imx708: Follow the standard devicetree labels
Switch the system clock name from "xclk" to "inclk".
Use lower case lables for all regulator names.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drives: media: imx708: Put HFLIP and VFLIP controls in a cluster
Create a cluster for the HVLIP and VFLIP controls so they are treated
as a single composite control.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: imx708: Adjust broken line correction parameter
In full-resolution mode, the LPF_INTENSITY_EN and LPF_INTENSITY
registers control Quad Bayer Re-mosaic broken line correction.
Expose this as a module parameter "qbc_adjust": zero disables
the correction and values in the range 2 to 5 set its strength.
There is a trade-off between coloured and monochrome patterns.
The previous fixed value 4 could produce ladder/spots artefacts
in coloured textures. The new default value 2 may suit a wider
range of scenes.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
media: i2c: imx708: Squash fixes
media: i2c: imx708: Fix lockdep issues.
The driver had a lockdep_assert_held in imx708_get_format_code,
but the calls from enum_mbus_code and enum_frame_size didn't take
the mutex.
Likewise imx708_set_framing_limits calling __v4l2_ctrl_modify_range
had a lockdep, but when going through the probe function the mutex
hadn't been taken.
Fix both cases.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: Tweak default PDAF gain table in imx708 driver
After analyzing more Raspberry Pi V3 cameras, adjust the
default PDAF shield-pixel gain tables (they can still be
overridden by camera OTP where programmed).
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Replace the existing imx708.yaml file with sony,imx708.yaml that follows
the latest devicetree conventions for camera sensors.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add YAML devicetree binding for IMX708 CMOS image sensor.
Let's also add a MAINTAINERS entry for the binding and driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The power up/down sequence is already ramped. Extend this to
the first user movement as well, as this will generally avoid
the "tick" noises due to rapid movements and overshooting.
Subsequent movements are generally smaller and so don't cause
issues.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Uses the regulator notifier framework so that the current
focus position will be restored whenever any user of the
regulator powers it up. This means that should the VCM
and sensor share a common regulator then starting the sensor
will automatically restore the default position. If they
have independent regulators then it will behave be powered
up when the VCM subdev is opened.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The VCM driver will often be controlled via a regulator,
therefore add in the relevant DT hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The DW9817 is effectively the same as DW9807 from a programming
interface, however it drives +/-100mA instead of 0-100mA. This means
that the power on ramp needs to take the lens from the midpoint, and
power off return it there. It also changes the default position for
the module.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The DW9817 is programmatically the same as DW9807, but
the output drive is a bi-directional -100 to +100mA
instead of 0-100mA.
Add the appropriate compativle string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
On some switches, having EEE enabled causes the link to become
unstable. With this patch, adding 'genet.eee=N' to the kernel command
line will cause EEE to be disabled on the link.
See: https://github.com/raspberrypi/linux/issues/4289
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
As there isn't currently a defined mechanism for selecting an
external trigger mode on image sensors, copy the imx477
approach of using a module parameter to enable ext trig.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Whilst the adv7180 driver support s_routing, nothing else
does, and there is a missing lump of framework code to
define the mapping from connectors on a board to the inputs
they represent on the ADV7180.
Add a nasty hack to take a module parameter that is passed in
to s_routing on any call to G_STD, or S_STD (or subdev
g_input_status call).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
There is no obligation for all source devices on a video-mux to
require the same bus configuration, so read the configuration
from the sink ports, and relay via get_mbus_config on the source
port.
If the sources support get_mbus_config, then call that first.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The BCM54213PE identifier is a RPI-specific addition.
Populate the remainder of the driver functions, including the
required probe routine.
Add a version of bcm54xx_suspend, from upstream.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Also check for which HDMI devices are connected and only create
devices for those that are present.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
snd_bcm2835: disable HDMI audio when vc4 is used (#3640)
Things don't work too well when both the vc4 driver and the firmware
driver are trying to control the same audio output:
[ 763.569406] bcm2835_audio bcm2835_audio: vchi message timeout, msg=5
Hence, when the vc4 HDMI driver is used, let it control audio. This is done
by introducing a new device tree property to the audio node, and
extending the vc4-kms-v3d overlays to set it appropriately.
Signed-off-by: Hristo Venev <hristo@venev.name>
staging: bcm2835-audio: Add disable-headphones flag
Add a property to allow the headphone output to be disabled. Use an
integer property rather than a boolean so that an overlay can clear it.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
staging: bcm2835-audio: Find compatible firmware node
Commit "ARM: dts: Adopt the upstream snd_bcm2835 handling" removed the
audio section from the DT and the driver can no longer access the
referenced firmware node 'brcm,firmware'. Fix that by searching for a
compatible firmware node instead, similar to drivers/gpu/drm/vc4.
Fixes: b9e62329e096 ("ARM: dts: Adopt the upstream snd_bcm2835 handling")
Signed-off-by: Juerg Haefliger <juergh@proton.me>
staging: bcm2835-audio: Fix firmware node refcounting
Decrement firmware node refcounts on all exit paths in set_hdmi_enables().
Signed-off-by: Juerg Haefliger <juergh@proton.me>
staging: bcm2835-audio: Log errors in case of firmware query failures
The driver queries the firmware for the number of detected HDMI displays
and their IDs. Log error messages if queries fail.
Signed-off-by: Juerg Haefliger <juergh@proton.me>
staging: bcm2835-audio: Fix unused enable_hdmi module parameter
The commit "Add HDMI1 facility to the driver." made the enable_hdmi module
parameter unused. Fix that by making it a global switch for all available
HDMI audio outputs.
Fixes: 755f336608 ("Add HDMI1 facility to the driver.")
Signed-off-by: Juerg Haefliger <juergh@proton.me>
staging: bcm2835-audio: Fix unused enable_headphones module parameter
Since commit "staging: bcm2835-audio: Add disable-headphones flag" the
enabling/disabling of the headphones output is solely determined by the
presence of the DT property 'brcm,disable-headphones' and the
enable_headphones module parameter is unused. Fix that by making it a
global switch.
Fixes: ee90e47d88 ("staging: bcm2835-audio: Add disable-headphones flag")
Signed-off-by: Juerg Haefliger <juergh@proton.me>
Add a driver for the Arducam 64MP camera sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
9152x6944 10-bit @ 2.7fps
4624x3472 10-bit (binned) @ 10fps
3840x2160 10-bit (cropped/binned) @ 20fps
2312x1736 10-bit (binned) @ 30fps
1920x1080 10-bit (cropped/binned) @ 60fps
1280x720 10-bit (cropped/binned) @ 120fps
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: arducam_64mp: Advertise embedded data node on media pad 1
This commit updates the arducam_64mp driver to adverise support for
embedded data streams.
The arducam_64mp sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: arducam_64mp: Modify the line length of 1280x720 resolution
Arducam 64MP has specific requirements for the line length, and if these
conditions are not met, the camera will not function properly. Under the
previous configuration, once a stream off operation is performed, the
camera will not output any data, even if a stream on operation is
performed. This prevents us from switching from 1280x720 to another
resolution.
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
media: i2c: arducam_64mp: Add 8000x6000 resolution
Added 8000x6000 10-bit (cropped) @ 3fps mode for Arducam 64MP
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
media: i2c: arducam_64mp: Add PDAF support
Enable PDAF output for all modes, and also need to modify Embedded Line
Width to 11560 * 3 (two lines of Embedded Data + one line of PDAF).
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
drivers: media: arducam_64mp: Add V4L2_CID_LINK_FREQ control
Add V4L2_CID_LINK_FREQ as a read-only control with a value of 456 Mhz.
This will be used by the CFE driver to corretly setup the DPHY timing
parameters in the CSI-2 block.
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
[ I would like to pursue fixing this more directly first before actually
merging this, but I thought I'd send this to the list now anyway as a
the "backup" plan. If I can't figure out how to make headway on the
main plan in the next few days, it'll be easy to just do this. ]
Stephen reported that a static key warning splat appears during early
boot on systems that credit randomness from device trees that contain an
"rng-seed" property, because because setup_machine_fdt() is called
before jump_label_init() during setup_arch():
static_key_enable_cpuslocked(): static key '0xffffffe51c6fcfc0' used before call to jump_label_init()
WARNING: CPU: 0 PID: 0 at kernel/jump_label.c:166 static_key_enable_cpuslocked+0xb0/0xb8
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.18.0+ #224 44b43e377bfc84bc99bb5ab885ff694984ee09ff
pstate: 600001c9 (nZCv dAIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : static_key_enable_cpuslocked+0xb0/0xb8
lr : static_key_enable_cpuslocked+0xb0/0xb8
sp : ffffffe51c393cf0
x29: ffffffe51c393cf0 x28: 000000008185054c x27: 00000000f1042f10
x26: 0000000000000000 x25: 00000000f10302b2 x24: 0000002513200000
x23: 0000002513200000 x22: ffffffe51c1c9000 x21: fffffffdfdc00000
x20: ffffffe51c2f0831 x19: ffffffe51c6fcfc0 x18: 00000000ffff1020
x17: 00000000e1e2ac90 x16: 00000000000000e0 x15: ffffffe51b710708
x14: 0000000000000066 x13: 0000000000000018 x12: 0000000000000000
x11: 0000000000000000 x10: 00000000ffffffff x9 : 0000000000000000
x8 : 0000000000000000 x7 : 61632065726f6665 x6 : 6220646573752027
x5 : ffffffe51c641d25 x4 : ffffffe51c13142c x3 : ffff0a00ffffff05
x2 : 40000000ffffe003 x1 : 00000000000001c0 x0 : 0000000000000065
Call trace:
static_key_enable_cpuslocked+0xb0/0xb8
static_key_enable+0x2c/0x40
crng_set_ready+0x24/0x30
execute_in_process_context+0x80/0x90
_credit_init_bits+0x100/0x154
add_bootloader_randomness+0x64/0x78
early_init_dt_scan_chosen+0x140/0x184
early_init_dt_scan_nodes+0x28/0x4c
early_init_dt_scan+0x40/0x44
setup_machine_fdt+0x7c/0x120
setup_arch+0x74/0x1d8
start_kernel+0x84/0x44c
__primary_switched+0xc0/0xc8
---[ end trace 0000000000000000 ]---
random: crng init done
Machine model: Google Lazor (rev1 - 2) with LTE
A trivial fix went in to address this on arm64, 73e2d827a5 ("arm64:
Initialize jump labels before setup_machine_fdt()"). But it appears that
fixing it on other platforms might not be so trivial. Instead, defer the
setting of the static branch until later in the boot process.
Fixes: f5bda35fba ("random: use static branch for crng_ready()")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The driver had a number of issues, checkpatch warnings/errors,
and other limitations, so fix these up to make it usable.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
hwmon: emc2305: Add calls to initialise of cooling maps
Commit 46ef9d4ed2 ("hwmon: emc2305: fixups for driver submitted to
mailing lists") missed adding the call to thermal_of_cooling_device_register
required to configure any cooling maps for the device, hence stopping it
from actually ever changing speed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
hwmon: emc2305: Change OF properties pwm-min & pwm-max to u8
There is no DT binding for emc2305 as mainline are still
discussing how to do a generic fan binding.
The 5.15 driver was reading the "emc2305," properties
"cooling-levels", "pwm-max", "pwm-min", and "pwm-channel" as u8.
The overlay was writing them as u16 (;) so it was working.
The 6.1 driver was reading as u32, which failed as there is
insufficient data.
As this is all downstream only, revert to u8 to match 5.15.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
It is quite common for the devm_thermal_zone_of_sensor_register
to need to defer, so avoid spamming the log by using
dev_err_probe instead of dev_err.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a driver for the Arducam Pivariety series CSI2 camera sensor.
Signed-off-by: Lee Jackson <info@arducam.com>
SQUASH: Fix VIDEO_ARDUCAM_PIVARIETY Kconfig entry
The cherry-pick from rpi-5.17.y put it in the wrong section, and failed
to update it for 5.18.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
media: i2c: arducam-pivariety: Add custom controls
Add support for strobe_shift, strobe_width and mode custom controls.
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: arducam-pivariety: Fix mutex init and NULL pointer
The mutex used in arducam-pivariety was not properly initialized,
which could lead to undefined behavior. This also caused a NULL
pointer dereference under certain conditions.
This patch ensures the mutex is correctly initialized during probe
and prevents NULL pointer dereferences.
Signed-off-by: Yuriy Pasichnyk <yurijpasichnyk11@gmail.com>
Add YAML device tree binding for Arducam Pivariety CMOS image sensor, and
the relevant MAINTAINERS entries.
Signed-off-by: Lee Jackson <info@arducam.com>
On some platforms the cma area can be half the entire system memory,
meaning that allocations start happening in the cma area immediately.
This leads to fragmentation and subsequent fatal cma_alloc failures.
We introduce an "alloc_in_cma_threshold" parameter which requires that
this many sixteenths of the free pages must be in cma before it will
try to use them. By default this is set to 12, but the previous
behaviour can be restored by setting it to 8 on startup.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Adds a driver for the Analog Devices AD5398 10 bit
I2C DAC which is commonly used for driving VCM lens
mechanisms.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: Rename ad5398 to ad5398_vcm
There's already a regulator module called ad5398 that exposes
this device through the regulator API. That is meaningless in
the terms that it uses and how it maps to V4L2, so a new driver
was added. However the module name collision wasn't noted, so
rename it now.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a binding for Analog Devices AD5398 10bit current
sinking DAC when used as a lens VCM driver.
FIXME: Convert to YAML
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Omnivision OV2311 is a CSI2 1600x1300 global shutter image sensor.
Add a driver for it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: Update ov2311 Kconfig entry
Bring the OV2311 Kconfig declaration in line with upstream entries.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
media: i2c: ov2311: Fix uninitialized variable usage
Signed-off-by: Alexander Winkowski <dereference23@outlook.com>
"media: i2c: Remove .s_power() from ov7251" removed the call that
sent ov7251_global_init_setting to the sensor. Send it when starting
streaming.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The sck-idle-input property indicates that the spi-gpio driver should
return the SCK line to an input when the chip select signals are
inactive.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
https://github.com/raspberrypi/linux/issues/4440
Upstream has added additional device specific controls, so the
V4L2_CID_USER_BASE + 0x10e0 value that had been defined for use with
the ISP has been taken by something else (and +0x10f0 has been used as
well)
Duplicate the use on V4L2_CID_USER_BASE + 0x10e0 so that userspace
(libcamera) doesn't need to change. Once the driver is upstream, then
we'll update libcamera to adopt the new value as it then won't change.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Not all implementations wire up the enable GPIO and may just tie
it to a supply rail.
Make it optional.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The I2C to the Atmel is very fussy, and locks up easily on
Pi0-3 particularly on reads.
The LCD power status is controlled solely by this driver, so
rather than reading it back from the Atmel, use the cached
status last set.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
regulator/rpi-panel: Power off display on shutdown
Adds a shutdown function to turn off the backlight, bridge, and
touch controller on shutdown.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
regulator/rpi-panel: Remove the ID read
Reading from the Atmel has always been troublesome due to
clock stretching, and the driver does nothing with it anyway.
Remove the read and assume that if the overlay has been
configured (most likely through the firmware autodetection)
that the hardware is present.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
As happens occasionally, an upstream change has once again prevented
spidev from being loaded via Device Tree. We now need "spidev" to be
included in the new spi_device_id list, otherwise although the
spidev driver gets loaded no /dev/spidev*.* entries will appear.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
An unwanted side effect of enabling the BRCMDBG config setting is
redefining brcmf_info to be brcmf_err. This can be alarming to users
and makes it harder to spot real errors, so don't do it.
See: https://github.com/raspberrypi/linux/issues/4663
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
For cases where spare PWM outputs are available, but are desired
to be addressed a standard outputs instead.
Wraps a PWM channel as a new GPIO chip with the one output.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
pwm: gpio-pwm: follow pwm_apply_might_sleep() rename
Fixes: 03286093be68("drivers/gpio: Add a driver that wraps the PWM API as a GPIO controller")
Signed-off-by: Ratchanan Srirattanamet <peathot@hotmail.com>
Some platforms include a fan-speed register that reports RPM directly
as an alternative to counting interrupts from the fan tachometer input.
Add support for reading a register at a given offset (rpm-offset) within
a block declared in another node (rpm-regmap). This indirection allows
the usual address mapping to be performed, and for address sharing with
another driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Should we go through the timeout failure case with port_disable
not returning all buffers for whatever reason, the
buffers_with_vpu counter gets left at a non-zero value, which
will cause reference counting issues should the instance be
reused.
Reset the count when the port is enabled again, but before
any buffers have been sent to the VPU.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The firmware can only use I2C0 if the kernel isn't, therefore
with libcamera and DRM using it the PoE HAT fan control needs
to move to the kernel.
Add the option for the driver to be created by the PoE HAT core
MFD driver, and use the I2C regmap that provides to control fan
functions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Raspbery Pi PoE+ HAT exposes a fan controller and power
supply status reporting via a single I2C address.
Create an MFD device that allows loading of the relevant
sub-drivers, with a shared I2C regmap.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Serge Schneider <serge@raspberrypi.com>
power: rpi-poe: Drop CURRENT_AVG as it is not hardware averaged
As documented the _AVG parameters are meant to be hardware
averaged, but the implementation for the PoE+ HAT was done in
software in the firmware.
Drop the property.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
power: rpi-poe: Add option of being created by MFD or FW
The firmware can only use I2C0 if the kernel isn't, therefore
with libcamera and DRM using it the PoE HAT fan control needs
to move to the kernel.
Add the option for the driver to be created by the PoE HAT core
MFD driver, and use the I2C regmap that provides to control fan
functions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
power: rpi-poe: FIXUP DRIVER.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
As we're wanting to wrap the image_fx component for deinterlacing,
add the deinterlace algorithm values to enum mmal_parameter_imagefx
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds enum mmal_interlace_type and struct
mmal_parameter_video_interlace_type to allow for querying the
interlacing mode on decoders.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Bindings for the panel-dsi specific additions to panel-simple.
Allow for DSI specific bus settings and panel timing
to be define in devicetree. Very similar to panel-dpi.
Signed-off-by: Timon Skerutsch <kernel@diodes-delight.com>
The Geekworm MZP280 panel is a 480x640 (portrait) panel with a
capacitive touch interface and a 40 pin header meant to interface
directly with the Raspberry Pi. The screen is 2.8 inches diagonally,
and there appear to be at least 4 distinct versions all with the same
panel timings.
Timings were derived from drivers posted on the github located here:
https://github.com/tianyoujian/MZDPI/tree/master/vga
Additional details about this panel family can be found here:
https://wiki.geekworm.com/2.8_inch_Touch_Screen_for_Pi_zero
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
The regulator of the Waveshare DSI-TOUCH series panels is different.
Add a new driver for this regulator.
Signed-off-by: Waveshare_Team <support@waveshare.com>
drivers/regulator : Adjust power enable sequence
Avoid direct enabling of LCD power here.
Certain screens require immediate initialization after power-on
to prevent polarization.
Signed-off-by: Waveshare_Team <support@waveshare.com>
Waveshare sell a range of DSI panels of varying sizes, all
using a common MCU to control the panel and backlight.
Add a panel driver that supports these panels.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel: waveshare: Fix up timings for 10.1" panel
The 10.1" panel doesn't work with the timings defined. vc4
will always have been fixing up the timing due to the limited
integer divider, so compute the fixed up mode and use it
directly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drivers/gpu/drm/panel:fix waveshare panel software restart/shutdown display is abnormal
Fixed the screen stays white when the user restarts or shuts down
Signed-off-by: eng33 <eng33@waveshare.com>
drivers/gpu/drm/panel:Modify the DSI mode to fix the problem that 7.9inch cannot be displayed
Signed-off-by: eng33 <eng33@waveshare.com>
drivers/gpu/drm/panel:Modified the timing of 11.9inch to fix the issue that 11.9inch was displayed abnormally
Signed-off-by: eng33 <eng33@waveshare.com>
Driver:add waveshare 4inch dsi lcd (C) driver
Signed-off-by: Eng33 <eng33@waveshare.net>
drivers:gpu:drm:panel: Added waveshare 5.0inch, 6.25inch, and 8.8inch dsi screen devices
Signed-off-by: eng33 <eng33@waveshare.com>
drm: panel: Added waveshare 13.3inch panel
Signed-off-by: eng33 <eng33@waveshare.com>
drm: panel: Added waveshare 7.0inch h dsi screen support
Signed-off-by: Waveshare_Team <support@waveshare.com>
drivers/gpu/drm/panel : Add the device for the Waveshare DSI-TOUCH series panels.
the driver are provided for the Waveshare DSI-TOUCH series panels,
modelled after the other Ilitek controller drivers,
but not limited to Ilitek series controllers.
The aim is to offer a more consistent operation and
experience for the Waveshare DSI-TOUCH series panels.
Signed-off-by: Waveshare_Team <support@waveshare.com>
drivers/gpu/drm/panel : Update display driver
1) Add LCD power control
2) Added support for:
A) Add support for 3.4-DSI-TOUCH-C
B) Add support for 4-DSI-TOUCH-C
C) Add support for 8-DSI-TOUCH-A
D) Add support for 9-DSI-TOUCH-B
E) Add support for 10.1-DSI-TOUCH-B
F) Add support for 12.3-DSI-TOUCH-A
Signed-off-by: Waveshare_Team <support@waveshare.com>
The Top DisplayOptoelectronics (TDO) T17B driver chip is used
in the TL040HDS20CT panel (found in the Pimoroni HyperPixel4
Square display) and potentially other displays.
The driver chip supports SPI for configuration and DPI
video data.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This new panel uses the ILI9881C IC but needs an alternate
init sequence, and therefore requires a new compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Penk Chen <penk@cutiepi.io>
drm/panel: ilitek-ili9881c: Clean up on mipi_dsi_attach failure
mipi_dsi_attach is allowed to fail, and currently the probe
code doesn't clean up (mainly drm_panel_remove) if this happens.
Add cleanup code on failure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel: panel-ilitek9881c: Use cansleep methods
Use cansleep version of gpiod_set_value so external IO drivers (like
via I2C) can be used.
Signed-off-by: Mark Williams <mwp@mwp.id.au>
drm/panel: panel-ilitek9881c: Crystalfontz support
Add support for Crystalfontz CFAF7201280A0-050Tx panel.
Signed-off-by: Mark Williams <mwp@mwp.id.au>
drm/panel: ili9881: Add configuration for the new panels
Add configuration for the 5" and 7" Raspberry Pi 720x1280
DSI panels based on ili9881.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Update panel-ilitek-ili9881c.c
Correcting display dimension typo
ILI9881C: Update timings for CFAF7201280A0-050TX
Update of ILI9881C CFAF7201280A0-050TX panel timing to work with the CM5.
Signed-off-by: Mark Williams <mark@crystalfontz.com>
There is no reason why the control GPIOs for the panel can not
be connected to I2C or similar GPIO interfaces that may need to
sleep, therefore switch from gpiod_set_value to
gpiod_set_value_cansleep calls to configure them.
Without that you get complaints from gpiolib every time the state
is changed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm: panel: jdi-lt070me05000: Add prepare_upstream_first flag
The panel driver wants to send DCS commands from the prepare
hook, therefore the DSI host wants to be pre_enabled first.
Set the flag to achieve this.
https://forums.raspberrypi.com/viewtopic.php?t=354708
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Raspberry Pi 7" 800x480 panel uses a Toshiba TC358762 DSI
to DPI bridge chip, so there is a requirement for the timings
to be specified for the end panel. Add such a definition.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel-simple: Populate bpc when using panel-dpi
panel-dpi doesn't know the bit depth, so in the same way that
DPI is guessed for the connector type, guess that it'll be 8bpc.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel-simple: Allow the bus format to be read from DT for panel-dpi
The "panel-dpi" compatible string configures panel from device tree,
but it doesn't provide any way of configuring the bus format (colour
representation), nor does it populate it.
Add a DT parameter "bus-format" that allows the MEDIA_BUS_FMT_xxx value
to be specified from device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel: simple: add Geekworm MZP280 Panel
Add support for the Geekworm MZP280 Panel
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
drm/panel: simple: Add Innolux AT056tN53V1 5.6" VGA
Add support for the Innolux AT056tN53V1 5.6" VGA (640x480) TFT LCD
panel.
Signed-off-by: Joerg Quinten <aBUGSworstnightmare@gmail.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
drm/panel: simple: Alter the timing for the Pi 7" DSI display
vc4 has always fixed up the timing, so the values defined have
never actually appeared on the wire.
The display appears to want a slightly longer HFP, so extend
the timings and recompute the clock to give the same frame rate.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel: add panel-dsi
Equivalent to panel-dpi for configuring a simple DSI panel with
device tree side timings and bus settings.
Motiviation is the same as for panel-dpi of wanting to support
new simple panels without needing to patch the kernel.
Signed-off-by: Timon Skerutsch <kernel@diodes-delight.com>
drm/panel-simple: Remove custom handling of orientation
The framework now handles reading orientation from DT, therefore
remove the custom get_orientation hook from panel-simple.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel-simple: Fix 7inch panel mode for misalignment
The 7inch panel is one line off the screen both horizontally
and vertically.
Alter the panel mode to correct this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel-simple: Increase pixel clock on Pi 7inch panel
The Toshiba bridge is very fussy and doesn't like the CM3
output when being told to produce a 27.777MHz pixel clock, which
is an almost perfect match to the DSI link integer divider.
Increasing to 30MHz will switch the DSI link from 333MHz to 400MHz
and makes the bridge happy with the same video timing as works
on Pi4.
(Pi4 will be using a link frequency of 375MHz due to a 3GHz
parent PLL).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
We now have the hardware I2C controller pinmuxed to the drive the
display I2C, but this controller does not support clock stretching.
The Atmel micro-controller in the panel requires clock stretching
to allow it to prepare any data to be read.
Split the rpi_touchscreen_i2c_read into two independent transactions with
a delay between them for the Atmel to prepare the data.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel/raspberrypi-ts: Insert delay before polling for startup state
In switching to the hardware I2C controller there is an issue
where we seem to not get back the correct state from the Pi
touchscreen.
Insert a delay before polling to avoid this condition.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel/raspberrypi-touchscreen: Handle I2C errors.
rpi_touchscreen_i2c_read returns any errors from i2c_transfer,
or the 8 bit received value.
Check for error values before trying to process the data as
valid.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/panel/raspberrypi-touchscreen: Insert more delays.
This avoids failures in cases where the panel is enabled
or re-probed very soon after being disabled or probed.
These can occur because the Atmel device can mis-behave
over I2C for a few ms after any write to the POWERON register.
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Whilst the hardware can't achieve the limits of level 4.2 under
all situations, it can exceed level 4.0.
Allow selection of levels 4.1 and 4.2.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Adafruit Mini-PiTFT13 display needs offsets applying when rotated,
so use the "variant" mechanism to select a custom set_addr_win method
using a dedicated compatible string of "fbtft,minipitft13".
See: https://github.com/raspberrypi/firmware/issues/1524
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
DMABUFs are all handled by videobuf2, so there is no reason not
to enable support for them.
Note that this driver is still using the vmalloc allocator, so
the buffers it allocates will not be compatible with the codec
or ISP driver that require contiguous buffers. However this
driver should be able to import the buffers allocated by them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
In order to simplify the driver slightly, use the same PLL
configuration, and hence pixel rate and link frequency (to be
added) for the full, 1080p, and binned modes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
There are many registers in common between all the modes.
Pull those out into one common table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
To make comparisons of the mode registers easier, put the registers
for the binned and VGA modes in the same order as the others.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver did expose V4L2_CID_HBLANK, but as a READ_ONLY control.
The sensor only uses the HTS register to control the line length,
so convert this control to read/write, with the appropriate ranges.
Adopt the old fixed values as the minimum values permitted in each
mode to avoid issues of it not streaming.
This should allow exposure times up to ~3 seconds (up from ~1sec).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
v4l2_async_register_subdev doesn't bind in lens or flash drivers,
but v4l2_async_register_subdev_sensor does.
Switch to using v4l2_async_register_subdev_sensor.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The driver supported using GPIOs to control the shutdown line,
but no regulator control.
Add regulator hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add these missing V4L2 controls. Tested binned and full resolution
modes in all four orientations using Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Fixes the following v4l2-compliance failure:
fail: v4l2-test-controls.cpp(871): subscribe event for control 'User Controls' failed test
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Trial and error reveals that the minimum vblank value appears to be 24
(the OV5647 data sheet does not give any clues). This fixes streaming
lock-ups in full resolution mode.
Fixes: 9b5a5ebedc ("media: i2c: ov5647: Add support for V4L2_CID_VBLANK")
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
The top offset in the pixel array is actually 6 (see page 3-1 of the
OV5647 data sheet).
Fixes: f2f7ad5ce5 ("media: i2c: ov5647: Selection compliance fixes")
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Parse device properties and register controls for them using the V4L2
fwnode properties helpers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Previously they were returning positive non-zero codes for success,
which were getting passed up the call stack. Since release 4.19,
do_dentry_open (fs/open.c) has been catching these and flagging an
error. (So this driver has been broken since that date.)
Fixes: 3c2472a [media] media: i2c: Add support for OV5647 sensor
Signed-off-by: David Plowman <david.plowman@raspberrypi.org>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
The kernel modules aes-neon-blk and aes-neon-bs perform poorly, at least on
Cortex-A72 without crypto extensions. In fact, aes-arm64 outperforms them
on benchmarks, despite it being a simpler implementation (only accelerating
the single-block AES cipher).
For modes of operation where multiple cipher blocks can be processed in
parallel, aes-neon-bs outperforms aes-neon-blk by around 60-70% and aes-arm64
is another 10-20% faster still. But the difference is even more marked with
modes of operation with dependencies between neighbouring blocks, such as
CBC encryption, which defeat parallelism: in these cases, aes-arm64 is
typically around 250% faster than either aes-neon-blk or aes-neon-bs.
The key trade-off with aes-arm64 is that the look-up tables are situated in
RAM. This leaves them potentially open to cache timing attacks. The two other
modules, by contrast, load the look-up tables into NEON registers and so are
able to perform in constant time.
This patch aims to load aes-arm64 more often.
If none of the currently-loaded crypto modules implement a given algorithm,
a new one is typically selected for loading using a platform-neutral alias
describing the required algorithm. To enable users to still
load aes-neon-blk or aes-neon-bs if they really want them, while still
ensuring that aes-arm64 is usually selected, remove the aliases from
aes-neonbs-glue.c and aes-glue.c and apply them to aes-cipher-glue.c, but
still build the two NEON modules.
Since aes-glue.c can also be used to build aes-ce-blk, leave them enabled
if USE_V8_CRYPTO_EXTENSIONS is defined, to ensure they are selected if we
in future use a CPU which has the crypto extensions enabled.
Note that the algorithm priority specifiers are unchanged, so if
aes-neon-bs is loaded at the same time as aes-arm64, the former will be
used in preference. However, aes-neon-blk and aes-arm64 have tied priority,
so whichever module was loaded first will be used (assuming aes-neon-bs is
not loaded).
Signed-off-by: Ben Avison <bavison@riscosopen.org>
A relatively recent commit ([1]) contained optimisation for the PIO
SPI FIFO-filling functions. The commit message includes the phrase
"[t]he blind and counted loops are always called with nonzero count".
This is technically true, but it is still possible for count to become
zero before the loop is entered - if tfr->len is zero. Moving the loop
exit condition to the end of the loop saves a few cycles, but results
in a near-infinite loop should the revised count be zero on entry.
Strangely, zero-lengthed transfers aren't filtered by the SPI framework
and, even more strangely, the Python3 spidev library is triggering them
for no obvious reason.
Avoid the problem completely by bailing out of the main transfer
function early if trf->len is zero, although there may be a case for
moving the mitigation into the framework.
See: https://github.com/raspberrypi/linux/issues/4100
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 26751de25d ("spi: bcm2835: Micro-optimise FIFO loops")
Support has been added for the unpacked (16bpp) versions of
the MIPI raw 10, 12, and 14 formats, so add the 4CCs for them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
DSI1 on BCM2711 doesn't require the DMA workaround that is used
on BCM2835/6/7, therefore it needs a new compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Not all systems have the interrupt line wired up, so switch to
polling the touchscreen off a timer if no interrupt line is
configured.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
input: edt-ft5x06: Handle unreliable TOUCH_UP events
The ft5x06 is unreliable in sending touch up events, so some
touch IDs can become stuck in the detected state.
Ensure that IDs that are unreported by the controller are
released.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
input: edt-ft5x06: Only look at the number of points reported
Register 0x02 in the FT5x06 is TD_STATUS containing the number
of valid touch points being reported.
Iterate over that number of points rather than all that are
supported on the device.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
input: edt-ft5x06: Only read data for number of points reported
Rather than always reading the maximum number of points supported
by the chip (which may be as high as 10), read the number of
active points first, and read data for just those.
In most cases this will result in less data on the I2C bus,
with only the maximum touch points taking more due to a second
read that has to configure the start address.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
input: edt-ft5x06: Fix patch reading only the number of points reported
Fix bad conflict resolution from upstream updates. Need to read
from tsdata->tdata_offset bytes, not from tsdata->offset.
Also fix logging of i2c read errors to cover both transactions.
Fixes: 7216fcfe2e ("input: edt-ft5x06: Only read data for number of points reported")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Input: edt-ft54x6: Clean up timer and workqueue on remove
If no interrupt is defined then a timer and workqueue are used
to poll the controller.
On remove these were not being cleaned up correctly.
Fixes: ca61fdaba7 "Input: edt-ft5x06: Poll the device if no interrupt is
configured."
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
input: touchscreen: edt-ft5x06: Suppress bogus data on startup
When polled without the use of IRQ, FT5x06 registers may return
undefined initial data, causing unwanted touches or event spamming.
A simple way to filter this out is to suppress touches until the
TD_STATUS register changes for the first time.
Increase the delay before first polling to 300ms, to avoid
transient I2C read flakiness that seems to occur after reset.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
input: edt-ft5x06: Include I2C details in names for the devices
libinput uses the input device name alone. If you have two
identical input devices, then there is no way to differentiate
between them, and in the case of touchscreens that means no
way to associate them with the appropriate display device.
Add the I2C bus and address to the start of the input device
name so that the name is always unique within the system.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
input: edt-ft5x06: Correct prefix length in snprintf
snprintf takes the length of the array that we can print into,
and has to fit the NULL terminator in there too.
Printing the prefix is generally "12-3456 " which is 8 desired
characters (the length of EDT_NAME_PREFIX_LEN) and the NULL.
The space is therefore being truncated to fit the NULL in.
Increase the length snprintf is allowed to use.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Define a new mailbox (SET_REBOOT_FLAGS) which may be used to
pass optional flags to the Raspberry Pi firmware that changes
the behaviour of the bootloader and firmware during a reboot.
Currently this just defines the 'tryboot' flag which causes
the firmware to load tryboot.txt instead config.txt. This
alternate configuration file can be used to specify the
path of an alternate firmware and kernels allowing a fallback
mechanism to be implemented for OS upgrades.
The gpio-fsm driver implements simple state machines that allow GPIOs
to be controlled in response to inputs from other GPIOs - real and
soft/virtual - and time delays. It can:
+ create dummy GPIOs for drivers that demand them,
+ drive multiple GPIOs from a single input, with optional delays,
+ add a debounce circuit to an input,
+ drive pattern sequences onto LEDs
etc.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Fix a build warning
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Rename 'num-soft-gpios' to avoid warning
As of 5.10, the Device Tree parser warns about properties that look
like references to "suppliers" of various services. "num-soft-gpios"
resembles a declaration of a GPIO called "num-soft", causing the value
to be interpreted as a phandle, the owner of which is checked for a
"#gpio-cells" property.
To avoid this warning, rename the gpio-fsm property to "num-swgpios".
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Show state info in /sys/class/gpio-fsm
Add gpio-fsm sysfs entries under /sys/class/gpio-fsm. For each state
machine show the current state, which state (if any) will be entered
after a delay, and the current value of that delay.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Fix shutdown timeout handling
The driver is intended to jump directly to a shutdown state in the
event of a timeout during shutdown, but the sense of the test was
inverted.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Clamp the delay time to zero
The sysfs delay_ms value is calculated live, and it is possible for
the time left to appear to be negative briefly if the timer handling
hasn't completed. Ensure the displayed value never goes below zero,
for the sake of appearances.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Sort functions into a more logical order
Move some functions into a more logical ordering. This change causes
no functional change and is essentially cosmetic.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio_fsm: Rework the atomic-vs-non-atomic split
Partition the code to separate atomic and non-atomic methods so that
none of them have to handle both cases. The result avoids using deferred
work unless necessary, and should be easier to understand.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Driver for the BCM2835 ISP hardware block. This driver uses the MMAL
component to program the ISP hardware through the VC firmware.
The ISP component can produce two video stream outputs, and Bayer
image statistics. This can't be encompassed in a simple V4L2
M2M device, so create a new device that registers 4 video nodes.
This patch squashes all the development patches from the earlier
rpi-5.4.y branch into one
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
staging/bcm2835-isp: Add the unpacked (16bpp) raw formats
Now that the firmware supports the unpacked (16bpp) variants
of the MIPI raw formats, add the mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-isp: Log the number of excess supported formats
When logging that the firmware has provided more supported formats
than we had allocated storage for, log the number allocated and
returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: vc04_services: ISP: Add colour denoise control
Add colour denoise control to the bcm2835 driver through a new v4l2
control: V4L2_CID_USER_BCM2835_ISP_CDN.
Add the accompanying MMAL configuration structure definitions as well.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
bcm2835-isp: Allow formats with different colour spaces.
Each supported format now includes a mask showing the allowed colour
spaces, as well as a default colour space for when one was not
specified.
Additionally we translate the colour space to mmal format and pass it
over to the VideoCore.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: add ov9281 driver.
Change-Id: I7b77250bbc56d2f861450cf77271ad15f9b88ab1
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
media: i2c: ov9281: fix mclk issue when probe multiple camera.
Takes the ov9281 part only from the Rockchip's patch.
Change-Id: I30e833baf2c1bb07d6d87ddb3b00759ab45a90e4
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
media: i2c: ov9281: add enum_frame_interval function for iq tool 2.2 and hal3
Adds the ov9281 parts of the Rockchip patch adding enum_frame_interval to
a large number of drivers.
Change-Id: I03344cd6cf278dd7c18fce8e97479089ef185a5c
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
media: i2c: ov9281: Fixup for recent kernel releases, and remove custom code
The Rockchip driver was based on a 4.4 kernel, and had several custom
Rockchip parts.
Update to 5.4 kernel APIs, with the relevant controls required by
libcamera, and remove custom Rockchip parts.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: ov9281: Read chip ID via 2 reads
Vision Components have made an OV9281 module which blocks reading
back the majority of registers to comply with NDAs, and in doing
so doesn't allow auto-increment register reading as used when
reading the chip ID.
Use two reads and manually combine the results.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: ov9281: Add support for 8 bit readout
The sensor supports 8 bit mode as well as 10bit, so add the
relevant code to allow selection of this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: ov9281: Add 1280x720 and 640x480 modes
Breaks out common register set and adds the different registers
for 1280x720 (cropped) and 640x480 (skipped) modes
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fixed picture line bug in all ov9281 modes
Signed-off-by: Mathias Anhalt <mathiasanhalt@web.de>
Added hflip and vflip controls to ov9281
Signed-off-by: Mathias Anhalt <mathiasanhalt@web.de>
media: i2c: ov9281: Remove override of subdev name
From the original Rockchip driver, the subdev was renamed
from the default to being "mov9281 <dev_name>" whereas the
default would have been "ov9281 <dev_name>".
Remove the override to drop back to the default rather than
a vendor custom string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: v4l2-subdev: add subdev-wide state struct
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
media: i2c: ov9281: Add fwnode properties controls
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: ov9281: Sensor should report RAW color space
Tested on Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Partial revert "media: i2c: add ov9281 driver."
This partially reverts commit 84e98e3a4f.
The commit had merged some changes to other drivers with adding the ov9281
driver. Only the ov9281 parts have been reverted.
staging/bcm2835-isp: Fix compiler warning
The result of dividing a u32 by a size_t is an unsigned int on arm32
and a long unsigned int on arm64. Use "%zu" (the size_t format) to
remove the build warning for 64-bit builds.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
staging: vc04_services: isp: Set the YUV420/YVU420 format stride to 64 bytes
The bcm2835 ISP requires the base address of all input/output planes to have 32
byte alignment. Using a Y stride of 32 bytes would not guarantee that the V
plane would fulfil this, e.g. a height of 650 lines would mean the V plane
buffer is not 32 byte aligned for YUV420 formats.
Having a Y stride of 64 bytes would ensure both U and V planes have a 32 byte
alignment, as the luma height will always be an even number of lines.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
vc04_services: isp: Report input node as wanting full range RAW color space
RAW color spaces are more usually reported as having full range
quantization.
Tested using libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
drivers: bcm2835_isp: Allow multiple users for the ISP driver.
Add a second (identical) set of device nodes to allow concurrent use of the ISP
hardware by another user. This change effectively creates a second state
structure (struct bcm2835_isp_dev) to maintain independent state for the second
user. Node and media entity names are appened with the instance index
appropriately.
Further users can be added by changing the BCM2835_ISP_NUM_INSTANCES define.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: bcm2835_isp: Fix div by 0 bug.
Fix a possible division by 0 bug when setting up the mmal port for the stats
port.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
staging/bcm2835-isp: Fix cleanup after init fail
bcm2835_isp_remove is called on an initialisation failure, but at that
point the drvdata hasn't been set. This causes a crash when e.g. using
the cutdown firmware (gpu_mem=16).
Move platform_set_drvdata before the instance probing loop to avoid the
problem.
See: https://github.com/raspberrypi/linux/issues/4774
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2835-v4l2-isp: Add missing lock initialization
ISP device allocation is dynamic hence the locks too.
struct mutex queue_lock is not initialized which result in bug.
Fixing same by initializing it.
[ 29.847138] INFO: trying to register non-static key.
[ 29.847156] The code is fine but needs lockdep annotation, or maybe
[ 29.847159] you didn't initialize this object before use?
[ 29.847161] turning off the locking correctness validator.
[ 29.847167] CPU: 1 PID: 343 Comm: v4l_id Tainted: G C 5.15.11-rt24-v8+ #8
[ 29.847187] Hardware name: Raspberry Pi 4 Model B Rev 1.4 (DT)
[ 29.847194] Call trace:
[ 29.847197] dump_backtrace+0x0/0x1b8
[ 29.847227] show_stack+0x20/0x30
[ 29.847240] dump_stack_lvl+0x8c/0xb8
[ 29.847254] dump_stack+0x18/0x34
[ 29.847263] register_lock_class+0x494/0x4a0
[ 29.847278] __lock_acquire+0x80/0x1680
[ 29.847289] lock_acquire+0x214/0x3a0
[ 29.847300] mutex_lock_nested+0x70/0xc8
[ 29.847312] _vb2_fop_release+0x3c/0xa8 [videobuf2_v4l2]
[ 29.847346] vb2_fop_release+0x34/0x60 [videobuf2_v4l2]
[ 29.847367] v4l2_release+0xc8/0x108 [videodev]
[ 29.847453] __fput+0x8c/0x258
[ 29.847476] ____fput+0x18/0x28
[ 29.847487] task_work_run+0x98/0x180
[ 29.847502] do_notify_resume+0x228/0x3f8
[ 29.847515] el0_svc+0xec/0xf0
[ 29.847523] el0t_64_sync_handler+0x90/0xb8
[ 29.847531] el0t_64_sync+0x180/0x184
Signed-off-by: Padmanabha Srinivasaiah <treasure4paddy@gmail.com>
staging: vc04_services: isp: Permit all sRGB colour spaces on ISP outputs
ISP outputs actually support all colour spaces that are fundamentally
sRGB underneath, regardless of whether an RGB or YUV output format is
actually requested.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
drivers: staging: bcm2835-isp: Do not cleanup mmal vcsm buffer on stop_streaming
On stop_streaming() the vcsm buffer handle gets released by the buffer cleanup
code. This will subsequently cause and error if userland re-queues the same
buffer on the next start_streaming() call.
Remove this cleanup code and rely on the vb2_ops->buf_cleanup() call to do the
cleanups instead.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: staging: bcm2835-isp: Clear LS table handle in the firmware
When all nodes have stopped streaming, ensure the firmware has released its
handle on the LS table dmabuf. This is done by passing a null handle in the
LS params.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: staging: bcm2835-isp: Respect caller's stride value
The stride value reported for output image buffers should be at least
as large as any value that was passed in by the caller (subject to
correct alignment for the pixel format). If the value is zero (meaning
no value was passed), or is too small, the minimum acceptable value
will be substituted.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
staging: vc04_services: bcm2835-isp: Drop include Makefile directive
Drop the include directive. They can break the build, when one only
wants to build a subdirectory. Replace with "../" for the includes in
the bcm2835-isp instead.
The fix is equivalent to the four patches between 29d49a76c5
("staging: vc04_services: bcm2835-audio: Drop include Makefile
directive")...2529ca211402 ("staging: vc04_services: interface: Drop
include Makefile directive")
Fixes: c8f89c9551c1 ("staging: vc04_services: ISP: Add a more complex ISP processing component")
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
staging: vc04_services: bcm2835-v4l2-isp: Register with vchiq_bus_type
Register the bcm2835-v4l2-isp driver with the vchiq_bus_type instead of
using the platform driver/device.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
staging: vc04_services: bcm2835-v4l2-isp: Explicitly set DMA mask
The platform model originally handled the DMA mask. Now that
we are on the vchiq_bus we need to explicitly set this.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
drivers: media: bcm2835_isp: Cache LS table dmabuf
Clients such as libcamera do not change the LS table dmabuf on every
frame. In such cases instead of mapping/remapping the same dmabuf on
every frame to send to the firmware, cache the dmabuf once and only
update and remap if the dmabuf has been changed by the userland client.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This file defines the userland interface to the bcm2835-isp driver
that will follow in a separate commit.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
uapi: bcm2835-isp: Add colour denoise configuration
Add a configuration structure for colour denoise to the bcm2835_isp
driver.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This adds a V4L2 memory to memory device that wraps the MMAL
video decode and video_encode components for H264 and MJPEG encode
and decode, MPEG4, H263, and VP8 decode (and MPEG2 decode
if the appropriate licence has been purchased).
This patch squashes all the work done in developing the driver
on the Raspberry Pi rpi-5.4.y kernel branch.
Thanks to Kieran Bingham, Aman Gupta, Chen-Yu Tsai, and
Marek Behún for their contributions. Please refer to the
rpi-5.4.y branch for the full history.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Ensure OUTPUT timestamps are always forwarded
The firmware by default tries to ensure that decoded frame
timestamps always increment. This is counter to the V4L2 API
which wants exactly the OUTPUT queue timestamps passed to the
CAPTURE queue buffers.
Disable the firmware option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/vc04_services/codec: Add support for CID MPEG_HEADER_MODE
Control V4L2_CID_MPEG_VIDEO_HEADER_MODE controls whether the encoder
is meant to emit the header bytes as a separate packet or with the
first encoded frame.
Add support for it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/vc04_services/codec: Clear last buf dequeued flag on START
It appears that the V4L2 M2M framework requires the driver to manually
call vb2_clear_last_buffer_dequeued on the CAPTURE queue during a
V4L2_DEC_CMD_START.
Add such a call.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/vc04-services/codec: Fix logical precedence issue
Two issues identified with operator precedence in logical
expressions. Fix them.
https://github.com/raspberrypi/linux/issues/4040
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Switch to s32fract
staging/bcm2835-codec: Add the unpacked (16bpp) raw formats
Now that the firmware supports the unpacked (16bpp) variants
of the MIPI raw formats, add the mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Log the number of excess supported formats
When logging that the firmware has provided more supported formats
than we had allocated storage for, log the number allocated and
returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Add support for pixel aspect ratio
If the format is detected by the driver and a V4L2_EVENT_SOURCE_CHANGE
event is generated, then pass on the pixel aspect ratio as well.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Implement additional g_selection calls for decode
v4l_cropcap calls our vidioc_g_pixelaspect function to get the pixel
aspect ratio, but also calls g_selection for V4L2_SEL_TGT_CROP_BOUNDS
and V4L2_SEL_TGT_CROP_DEFAULT. Whilst it allows for vidioc_g_pixelaspect
not to be implemented, it doesn't allow for either of the other two.
Add in support for the additional selection targets.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Add VC-1 support.
Providing the relevant licence has been purchased, then Pi0-3
can decode VC-1.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Fix support for levels 4.1 and 4.2
The driver said it supported H264 levels 4.1 and 4.2, but
was missing the V4L2 to MMAL mappings.
Add in those mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Set the colourspace appropriately for RGB formats
Video decode supports YUV and RGB formats. YUV needs to report SMPTE170M
or REC709 appropriately, whilst RGB should report SRGB.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Pass corrupt frame flag.
MMAL has the flag MMAL_BUFFER_HEADER_FLAG_CORRUPTED but that
wasn't being passed through, so add it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Do not update crop from S_FMT after res change
During decode, setting the CAPTURE queue format was setting the crop
rectangle to the requested height before aligning up the format to
cater for simple clients that weren't expecting to deal with cropping
and the SELECTION API.
This caused problems on some resolution change events if the client
didn't also then use the selection API.
Disable the crop update after a resolution change.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
bcm2835: Allow compressed frames to set sizeimage (#4386)
Allow the user to set sizeimage in TRY_FMT and S_FMT if the format
flags have V4L2_FMT_FLAG_COMPRESSED set
Signed-off-by: John Cox <jc@kynesim.co.uk>
staging/bcm2835-codec: Change the default codec res to 32x32
In order to effectively guarantee that a V4L2_EVENT_SOURCE_CHANGE
event occurs, adopt a default resolution of 32x32 so that it
is incredibly unlikely to be decoding a stream of that resolution
and therefore failing to note a "change" requiring the event.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Add support for decoding interlaced streams
The video decoder can support decoding interlaced streams, so add
the required plumbing to signal this correctly.
The encoder and ISP do NOT support interlaced data, so trying to
configure an interlaced format on those nodes will be rejected.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Correct ENUM_FRAMESIZES stepsize to 2
Being YUV420 formats, the step size is always 2 to avoid part
chroma subsampling.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Return buffers to QUEUED not ERROR state
Should start_streaming fail, or buffers be queued during
stop_streaming, they should be returned to the core as QUEUED
and not (as currently) as ERROR.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835_codec: Log MMAL flags in hex
The flags is a bitmask, so it's far easier to interpret as hex
data instead of decimal.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Allow custom specified strides/bytesperline.
If the client provides a bytesperline value in try_fmt/s_fmt then
validate it and correct if necessary.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835_codec: Add support for image_fx to deinterlace
Adds another /dev/video node wrapping image_fx doing deinterlace.
Co-developed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
staging/bcm2835-v4l2_codec: Fix for encode selection API
Matches correct behaviour from DECODE and DEINTERLACE
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
staging: bcm2835-codec: Allow decode res changed before STREAMON(CAPTURE)
The V4L2 stateful video decoder API requires that you can STREAMON
on only the OUTPUT queue, feed in buffers, and wait for the
SOURCE_CHANGE event.
This requires that we enable the MMAL output port at the same time
as the input port, because the output port is the one that creates
the SOURCE_CHANGED event.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Do not send buffers to the VPU unless streaming
With video decode we now enable both input and output ports on
the component. This means that buffers will get passed to the VPU
earlier than desired if they are queued befoer STREAMON.
Check that the queue is streaming before sending buffers to the VPU.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Format changed should trigger drain
When a format changed event occurs, the spec says that it
triggers an implicit drain, and that needs to be signalled
via -EPIPE.
For BCM2835, the format changed event happens at the point
the format change occurs, so no further buffers exist from
before the resolution changed point. We therefore signal the
last buffer immediately.
We don't have a V4L2 available to us at this point, so set
the videobuf2 queue last_buffer_dequeued flag directly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Signal the firmware to stop on all changes
The firmware defaults to not stopping video decode if only the
pixel aspect ratio or colourspace change. V4L2 requires us
to stop decoding on any change, therefore tell the firmware
of the desire for this alternate behaviour.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Queue flushed buffers instead of completing
When a buffer is returned on a port that is disabled, return it
to the videobuf2 QUEUED state instead of DONE which returns it
to the client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835_codec: Correct flushing code for refcounting
Completions don't reference count, so setting the completion
on the first buffer returned and then not reinitialising it
means that the flush function doesn't behave as intended.
Signal the completion when the last buffer is returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Ensure all ctrls are set on streamon
Currently the code was only setting some controls from
bcm2835_codec_set_ctrls, but it's simpler to use
v4l2_ctrl_handler_setup to avoid forgetting to adding new
controls to the list.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Add support for H&V Flips to ISP
The ISP can do H & V flips whilst resizing or converting
the image, so expose that via V4L2_CID_[H|V]FLIP.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
bcm2835-v4l2-codec: Remove advertised support of VP8
The support for this format by firmware is very limited
and won't be faster than the arm.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Pass V4L2_CID_MPEG_VIDEO_H264_MIN_QP/MAX_QP to bcm2835-v4l2-codec
Following raspberrypi/linux#4704. This is necessary to set up
quantization for variable bitrate to avoid video flickering.
staging/bcm2835-codec: bytesperline for YUV420/YVU420 needs to be 64
Matching https://github.com/raspberrypi/linux/pull/4419, the ISP
block (which is also used on the input of the encoder, and output
of the decoder) needs the base address of all planes to be aligned
to multiples of 32. This includes the chroma planes of YUV420 and
YVU420.
If the height is only a multiple of 2 (not 4), then you get an odd
number of lines in the second plane, which means the 3rd plane
starts at a multiple of bytesperline/2.
Set the minimum bytesperline alignment to 64 for those formats
so that the plane alignment is always right.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Allow a different stride alignment per role
Deinterlace and decode aren't affected in the same way as encode
and ISP by the alignment requirement on 3 plane YUV420.
Decode would be affected, but it always aligns the height up to
a macroblock, and uses the selection API to reflect that.
Add in the facility to set the bytesperline alignment per role.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: vc04_services: codec: Add support for V4L2_PIX_FMT_RGBA32 format
We already support V4L2_PIX_FMT_BGR32 which is the same thing with red
and blue swapped, so it makes sense to include this variant as well.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
bcm2835-codec: Return empty buffers to the VPU instead of queueing to vbuf2
The encoder can skip frames totally should rate control overshoot
the target bitrate too far. In this situation it generates an
output buffer of length 0.
V4L2 treats a buffer of length 0 as an end of stream flag, which is
not appropriate in this case, therefore we can not return that buffer
to the client.
The driver was returning the buffer to videobuf2 in the QUEUED state,
however that buffer was then not dequeued again, so the number of
buffers was reduced each time this happened. In the pathological
case of using GStreamer's videotestsrc in mode 1 for noise, this happens
sufficiently frequently to totally stall the pipeline.
If the port is still enabled then return the buffer straight back to
the VPU rather than to videobuf2.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Add support for V4L2_PIX_FMT_NV12_COL128
V4L2_PIX_FMT_NV12_COL128 is supported by the ISP and the input of
video_encode, output of video_decode, and both input and output
of the ISP.
Add in the plumbing to support the format on those ports.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Set crop_height for compressed formats
In particular for the encoder where the CAPTURE format dictates
the parameters given to the codec we need to be able to set the
value passed as the crop_height for the compressed format.
There's no crop available for cropped modes, so always set
crop_height to the requested height.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Set port format from s_selection
s_selection allows the crop region of an uncompressed pixel
format to be specified, but it wasn't passing the setting on to
the firmware. Depending on call order this would potentially
mean that the crop wasn't actioned.
Set the port format on s_selection if we have a component created.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
bcm2835-codec: /dev/video31 as interface to image_encode JPEG encoder
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
bcm2835-v4l2-codec: support H.264 5.0 and 5.1 levels
vc04_services: bcm2835-codec: Remove redundant role check
vidioc_try_encoder_cmd checks the role, but the ioctl is disabled
for any roles in which it is invalid.
Remove the redundant check.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Allow encoder_cmd on ISP and deinterlace
ISP and deinterlace also need a mechanism for passing effectively
an EOS through the pipeline to signal when all buffers have been
processed.
VIDIOC_ENCODER_CMD does exactly this for encoders, so reuse the same
function for ISP and deinterlace.
(VIDIOC_DECODER_CMD is slightly different in that it also passes
details of when and how to stop, so is not as relevant).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835_codec: Allow larger images through the ISP
Whilst the codecs are restricted to 1920x1080 / 1080x1920, the ISP
isn't, but the limits advertised via V4L2 was 1920x1920 for all
roles.
Increase the limit to 16k x 16k for the ISP.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-v4l2-codec: Enable selection ioctl for ISP
The ISP cases do nothing. Remove the break that separates them from the
deinterlace case so they now do the same as deinterlace. This enables
simple width & height setting, but does not enable setting left and
top coordinates.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: bcm2835-v4l2-codec: Add profile & level ctrls to decode
In order to support discovery of what profile & levels are supported by
stateful decoders implement the profile and level controls where they
are defined by V4L2.
Signed-off-by: John Cox <jc@kynesim.co.uk>
vc04_services: bcm2835_codec: Ignore READ_ONLY ctrls in s_ctrl
In adding the MPEG2/MPEG4/H264 level and profile controls to
the decoder, they weren't declared as read-only, nor handlers
added to bcm2835_codec_s_ctrl. That resulted in an error message
"Invalid control" being logged every time v4l2_ctrl_handler_setup
was called from bcm2835_codec_create_component.
Define those controls as read only, and exit early from s_ctrl
on read only controls.
Fixes: "media: bcm2835-v4l2-codec: Add profile & level ctrls to decode"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835_codec: Set MPEG2_LEVEL control to READ_ONLY
V4L2_CID_MPEG_VIDEO_MPEG2_LEVEL was missed from
"vc04_services: bcm2835_codec: Ignore READ_ONLY ctrls in s_ctrl"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Add V4L2_CID_MPEG_VIDEO_B_FRAMES control
FFmpeg insists on trying to set V4L2_CID_MPEG_VIDEO_B_FRAMES to
0, and generates an error should it fail.
As our encoder doesn't support B frames, add a stub handler for
it to silence FFmpeg.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Add support for V4L2_CID_MPEG_VIDEO_GOP_SIZE
For H264, V4L2_CID_MPEG_VIDEO_H264_I_PERIOD is meant to be the intra
I-frame period, whilst V4L2_CID_MPEG_VIDEO_GOP_SIZE is the intra IDR
frame period.
The firmware encoder doesn't produce I-frames that aren't IDR as well,
therefore V4L2_CID_MPEG_VIDEO_GOP_SIZE is technically the correct
control, however users may have adopted V4L2_CID_MPEG_VIDEO_H264_I_PERIOD.
Add support for V4L2_CID_MPEG_VIDEO_GOP_SIZE controlling the encoder,
and have VIDIOC_S_CTRL for V4L2_CID_MPEG_VIDEO_H264_I_PERIOD update
the value for V4L2_CID_MPEG_VIDEO_GOP_SIZE (the reverse is not
implemented).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Add missing alignment for V4L2_PIX_FMT_RGBA32
The patch adding image encode (JPEG) to the driver missed adding
the alignment constraint for V4L2_PIX_FMT_RGBA32, which meant
it ended up giving a stride and size of 0.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Downgrade the level for a debug message
The debug message from bcm2835_codec_buf_prepare when the buffer
size is incorrect can be a little spammy if the application isn't
careful on how it drives it, therefore drop the priority of the
message.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Correct alignment requirements for YUYV
The firmware wants the YUYV format stride alignment to be to a multiple
of 32pixels / 64 bytes. The kernel driver was configuring it to a multiple
of 16 pixels / 32 bytes, which then failed when it tried starting to
stream.
Correct the alignment requirements.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Fix up for 6.8 - use ignore_cap_streaming
Drops downstream patch to v4l2_mem2mem, and uses the new mainline
flag to achieve the same functionality
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: 32bpp RGB formats need a 64byte alignment
The firmware needs 16 pixel alignment on RGBx 32bpp formats, which
would be 64 byte. The driver was only setting 32byte alignment.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835_codec: Pass framerate to the component if set late
For video encoding, if the framerate was set after the component
was created, then it wasn't set correctly on the port, and an
old value was encoded in the bitstream.
Update the port status when the framerate is set.
https://github.com/raspberrypi/rpicam-apps/issues/664
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: vc04_services: bcm2835-codec: Drop include Makefile directive
Drop the include directive. They can break the build, when one only
wants to build a subdirectory. Replace with "../" for the includes in
the bcm2835-v4l2-codec instead.
The fix is equivalent to the four patches between 29d49a76c5
("staging: vc04_services: bcm2835-audio: Drop include Makefile
directive")...2529ca211402 ("staging: vc04_services: interface: Drop
include Makefile directive")
Fixes: afaec52747 ("staging: vc04_services: Add a V4L2 M2M codec driver")
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
staging: vc04_services: bcm2835-v4l2-codec: Register with vchiq_bus_type
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
staging: vc04_services: bcm2835-codec: Explicitly set DMA mask
The platform model originally handled the DMA mask. Now that
we are on the vchiq_bus we need to explicitly set this.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
staging: bcm2835-codec: Disable HEADER_ON_OPEN for video encode
Video encode can defer generating the header until the first
frame is presented, which allows it to take the colourspace
information from the frame rather than just the format.
Enable that for the V4L2 driver now that the firmware populates
all the parameters.
https://github.com/raspberrypi/firmware/issues/1885
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Add support for H264 level 5.0 and 5.1
We do NOT claim to support decoding in real-time for these levels,
but can transcode some content, and handle 1920x1200.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: codec: Allocate the max number of buffers on the VPU
The VPU's API can't match the use of VIDIOC_CREATE_BUFS to add buffers
to the internal pool whilst a port is enabled, therefore allocate
the maximum number of buffers possible in V4L2 to avoid the issue.
As these are only buffer headers, the overhead is relatively small.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: vchiq-mmal: Add defines for mmal_es_format flags
There is a flags field in struct mmal_es_format, but the defines
for what the bits meant weren't included in the headers.
For V4L2_PIX_FMT_NV12_COL128 support we need them, so add them in.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
With the vc-sm-cma driver we can support zero copy of buffers between
the kernel and VPU. Add this support to mmal-vchiq.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc-sm-cma: fixed kbuild problem
error logs:
drivers/staging/vc04_services/vc-sm-cma/Kconfig:1:error: recursive dependency detected!
drivers/staging/vc04_services/vc-sm-cma/Kconfig:1: symbol BCM_VC_SM_CMA is selected by BCM2835_VCHIQ_MMAL
drivers/staging/vc04_services/vchiq-mmal/Kconfig:1: symbol BCM2835_VCHIQ_MMAL depends on BCM2835_VCHIQ
drivers/staging/vc04_services/Kconfig:14: symbol BCM2835_VCHIQ is selected by BCM_VC_SM_CMA
For a resolution refer to Documentation/kbuild/kconfig-language.rst
subsection "Kconfig recursive dependency limitations"
Tested-by: make ARCH=arm64 bcm2711_defconfig
Test platform: fedora 33
Branch: rpi-5.10.y
Add Broadcom VideoCore Shared Memory support.
This new driver allows contiguous memory blocks to be imported
into the VideoCore VPU memory map, and manages the lifetime of
those objects, only releasing the source dmabuf once the VPU has
confirmed it has finished with it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: vcsm-cma: Fix memory leak from not detaching dmabuf
When importing there was a missing call to detach the buffer,
so each import leaked the sg table entry.
Actually the release process for both locally allocated and
imported buffers is identical, so fix them to both use the same
function.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/vc-sm-cma: Avoid log spamming on Pi0/1 over cache alias.
Pi 0/1 use the 0x80000000 cache alias as the ARM also sees the world
through the VPU L2 cache.
vc-sm-cma was trying to ensure it was in an uncached alias (0xc), and
complaining on every allocation if it weren't. Reduce this logging.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc-sm-cma: Restore correct cache maintainance operations
We have been using the more expensive flush operations rather than
invalidate and clean since kernel rpi-5.9.y
These are exposed with:
52f1453513 Re-expose some dmi APIs for use in VCSM
But I believe that commit was dropped when (non-cma) vc-sm was dropped,
and didn't get updated when the commit was restored
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
staging: vc04_services: Fix clang14 warning
Insert a break to fix a fallthrough warning from clang14. Since the
fallthrough was to another break, this is a cosmetic change.
See: https://github.com/raspberrypi/linux/issues/5078
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
vc04_services/vc-sm-cma: Handle upstream require vchiq_instance to be passed around
vc04_services/vc-sm-cma: Switch one-bit bitfields to bool
Clang 16 warns:
../drivers/staging/vc04_services/vc-sm-cma/vc_sm.c:816:19: warning: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Wsingle-bit-bitfield-constant-conversion]
buffer->imported = 1;
^ ~
../drivers/staging/vc04_services/vc-sm-cma/vc_sm.c:822:17: warning: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Wsingle-bit-bitfield-constant-conversion]
buffer->in_use = 1;
^ ~
2 warnings generated.
Signed-off-by: Alexander Winkowski <dereference23@outlook.com>
vc04_services: vcsm-cma: Detach from the correct dmabuf
Commit d3292daee3 ("dma-buf: Make locking consistent in dma_buf_detach()")
added checking that the same dmabuf for which dma_buf_attach
was called is passed into dma_buf_detach, which flagged up
that vcsm-cma was passing in the wrong dmabuf.
Correct this so that we don't get the WARN on every dma_buf
release.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: vc04_services: vc-sm-cma: Remove deprecated header
The vchiq_connected.h header was removed in f875976ecf ("staging:
vc04_services: Drop vchiq_connected.[ch] files") to simplify the
implementation.
Update the vc_sm driver accordingly which can still use the same
functions through the vchiq_arm.h header declarations.
Fixes: b1ab7a05eb6c ("staging: vc04_services: Add new vc-sm-cma driver")
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
staging: vc04_services: vc-sm-cma: Drop include Makefile directive
Drop the include directive. They can break the build, when one only
wants to build a subdirectory. Replace with "../" for the includes in
the vc_sm files instead.
The fix is equivalent to the four patches between 29d49a76c5
("staging: vc04_services: bcm2835-audio: Drop include Makefile
directive")...2529ca211402 ("staging: vc04_services: interface: Drop
include Makefile directive")
Fixes: b1ab7a05eb6c ("staging: vc04_services: Add new vc-sm-cma driver")
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
staging: vc04_services: vc-sm-cma: Register with vchiq_bus_type
Register the vcsm rive with the vchiq_bus_type instead of useing the
platform driver/device.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
staging: vc04_services: vc-sm-cma: Explicitly set DMA mask
The platform model originally handled the DMA mask. Now that
we are on the vchiq_bus we need to explicitly set this.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
staging: vc04_services: vc-sm-cma: Use [map|unmap]_attachment_unlocked
lockdep throws warnings when using libcamera as buffers are
mapped and unmapped as the dmabuf->resv lock hasn't been taken.
Switch to using the _unlocked variants so that the framework takes
the lock.
https://github.com/raspberrypi/linux/issues/6814
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: vc04_services: vc-sm-cma: Use a mutex instead of spinlock
There are no contexts where we should be calling the kernelid_map
IDR functions where we can't sleep, so switch from using a spinlock
to using a mutex.
https://github.com/raspberrypi/linux/issues/6815
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: vc-sm-cma: Fix field-spanning write warning
Replace one-element array with flexible-array member to fix:
[ 11.725017] ------------[ cut here ]------------
[ 11.725038] memcpy: detected field-spanning write (size 4) of single field "hdr->body" at drivers/staging/vc04_services/vc-sm-cma/vc_sm_cma_vchi.c:130 (size 0)
[ 11.725113] WARNING: CPU: 3 PID: 455 at drivers/staging/vc04_services/vc-sm-cma/vc_sm_cma_vchi.c:130 vc_vchi_cmd_create+0x1a8/0x1d0 [vc_sm_cma]
Signed-off-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Increase the delay before entering the lower power state to 2 seconds
(the maximum allowed) in order to reduce the packet latencies,
particularly for inbound packets.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Display variants are intended as a replacement for the now-deleted
fbtft_device drivers. Drivers can register additional compatible
strings with a custom callback that can make the required changes
to the fbtft_display structure.
Start the ball rolling by adding adafruit18, adafruit18_green and
sainsmart18 displays.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The actpwr trigger is a meta trigger that cycles between an inverted
mmc0 and default-on. It is written in a way that could fairly easily
be generalised to support alternative sets of source triggers.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The upstream Unicam driver needs a set of userland changes to get
libcamera to run, and those aren't written or merged yet.
Move the "brcm,bcm2835-unicam" compatible from the upstream driver
to the old downstream version so that users can run libcamera
against 6.10.
Once the libcamera changes have been merged this can be reverted
to use the upstream driver.
If using the non-legacy compatible then assume we want to use
media-controller API for configuration.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add a driver for the Unicam camera receiver block on BCM283x processors.
Compared to the bcm2835-camera driver present in staging, this driver
handles the Unicam block only (CSI-2 receiver), and doesn't depend on
the VC4 firmware running on the VPU.
The commit is made up of a series of changes cherry-picked from the
rpi-5.4.y branch of https://github.com/raspberrypi/linux/ with
additional enhancements, forward-ported to the mainline kernel.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: kbuild test robot <lkp@intel.com>
media: bcm2835-unicam: Add support for get_mbus_config to set num lanes
Use the get_mbus_config pad subdev call to allow a source to use
fewer than the number of CSI2 lanes defined in device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Avoid gcc warning over {0} on endpoint
Older gcc versions object to = { 0 } initialisation if the first
elemtn in the structure is a substructure.
Use = { } to avoid this compiler warning.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Reinstate V4L2_CAP_READWRITE in the caps
v4l2-compliance throws a failure if the device doesn't advertise
V4L2_CAP_READWRITE but allows read or write operations.
We do support read, so reinstate the flag.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Ensure type is VIDEO_CAPTURE in [g|s]_selection
[g|s]_selection pass in a buffer type that needs to be validated
before passing on to the sensor subdev.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835: unicam: Set VPU min clock freq to 250Mhz.
When streaming with Unicam, the VPU must have a clock frequency of at
least 250Mhz. Otherwise, the input fifos could overrun, causing
image corruption.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: bcm2835-unicam: Drop WARN on uing direct cache alias
Pi 0&1 pass all ARM accesses through the VPU L2 cache, therefore
the dma-ranges property sets the cache alias bits to other
than the direct alias, hence this WARN was firing.
It was overprotective coding, so assume that everything is OK
with the dma-ranges, and remove the WARN.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Always service interrupts
From when bringing up the driver, there was a check in the isr
to ignore interrupts (claiming them handled) should the driver
not be streaming.
The VPU now will not register a camera driver if it finds a
CSI2 node enabled in device tree, therefore this flawed check is
redundant.
https://github.com/raspberrypi/linux/issues/3602
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835: unicam: Fix uninitialized warning
Signed-off-by: Jacko Dirks <jdirks.linuxdev@gmail.com>
media: bcm2835-unicam: Fixup review comments from Hans.
Updates the driver based on the upstream review comments from
Hans Verkuil at https://patchwork.linuxtv.org/patch/63531/
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Retain packing information on G_FMT
The change to retrieve the pixel format always on g_fmt didn't
check whether the native or unpacked version of the format
had been requested, and always returned the packed one.
Correct this so that the packing setting is retained whereever
possible.
Fixes "9d59e89 media: bcm2835-unicam: Re-fetch mbus code from subdev
on a g_fmt call"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: change minimum number of vb2_queue buffers to 1
Since the unicam driver was modified to write to a dummy buffer when no
user-supplied buffer is available, it can now write to and return a
buffer even when there's only a single one. Enable this by changing the
min_buffers_needed in the vb2_queue; it will be useful for enabling
still captures without allocating more memory than absolutely necessary.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
staging: vc04_services: ISP: Add a more complex ISP processing component
Driver for the BCM2835 ISP hardware block. This driver uses the MMAL
component to program the ISP hardware through the VC firmware.
The ISP component can produce two video stream outputs, and Bayer
image statistics. This can't be encompassed in a simple V4L2
M2M device, so create a new device that registers 4 video nodes.
This patch squashes all the development patches from the earlier
rpi-5.4.y branch into one
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
staging/bcm2835-isp: Add the unpacked (16bpp) raw formats
Now that the firmware supports the unpacked (16bpp) variants
of the MIPI raw formats, add the mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-isp: Log the number of excess supported formats
When logging that the firmware has provided more supported formats
than we had allocated storage for, log the number allocated and
returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: vc04_services: ISP: Add colour denoise control
Add colour denoise control to the bcm2835 driver through a new v4l2
control: V4L2_CID_USER_BCM2835_ISP_CDN.
Add the accompanying MMAL configuration structure definitions as well.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
bcm2835-isp: Allow formats with different colour spaces.
Each supported format now includes a mask showing the allowed colour
spaces, as well as a default colour space for when one was not
specified.
Additionally we translate the colour space to mmal format and pass it
over to the VideoCore.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: add ov9281 driver.
Change-Id: I7b77250bbc56d2f861450cf77271ad15f9b88ab1
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
media: i2c: ov9281: fix mclk issue when probe multiple camera.
Takes the ov9281 part only from the Rockchip's patch.
Change-Id: I30e833baf2c1bb07d6d87ddb3b00759ab45a90e4
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
media: i2c: ov9281: add enum_frame_interval function for iq tool 2.2 and hal3
Adds the ov9281 parts of the Rockchip patch adding enum_frame_interval to
a large number of drivers.
Change-Id: I03344cd6cf278dd7c18fce8e97479089ef185a5c
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
media: i2c: ov9281: Fixup for recent kernel releases, and remove custom code
The Rockchip driver was based on a 4.4 kernel, and had several custom
Rockchip parts.
Update to 5.4 kernel APIs, with the relevant controls required by
libcamera, and remove custom Rockchip parts.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: ov9281: Read chip ID via 2 reads
Vision Components have made an OV9281 module which blocks reading
back the majority of registers to comply with NDAs, and in doing
so doesn't allow auto-increment register reading as used when
reading the chip ID.
Use two reads and manually combine the results.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: ov9281: Add support for 8 bit readout
The sensor supports 8 bit mode as well as 10bit, so add the
relevant code to allow selection of this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: ov9281: Add 1280x720 and 640x480 modes
Breaks out common register set and adds the different registers
for 1280x720 (cropped) and 640x480 (skipped) modes
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fixed picture line bug in all ov9281 modes
Signed-off-by: Mathias Anhalt <mathiasanhalt@web.de>
Added hflip and vflip controls to ov9281
Signed-off-by: Mathias Anhalt <mathiasanhalt@web.de>
media: i2c: ov9281: Remove override of subdev name
From the original Rockchip driver, the subdev was renamed
from the default to being "mov9281 <dev_name>" whereas the
default would have been "ov9281 <dev_name>".
Remove the override to drop back to the default rather than
a vendor custom string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: v4l2-subdev: add subdev-wide state struct
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
media: i2c: ov9281: Add fwnode properties controls
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: ov9281: Sensor should report RAW color space
Tested on Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Partial revert "media: i2c: add ov9281 driver."
This partially reverts commit 84e98e3a4f.
The commit had merged some changes to other drivers with adding the ov9281
driver. Only the ov9281 parts have been reverted.
staging/bcm2835-isp: Fix compiler warning
The result of dividing a u32 by a size_t is an unsigned int on arm32
and a long unsigned int on arm64. Use "%zu" (the size_t format) to
remove the build warning for 64-bit builds.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
staging: vc04_services: isp: Set the YUV420/YVU420 format stride to 64 bytes
The bcm2835 ISP requires the base address of all input/output planes to have 32
byte alignment. Using a Y stride of 32 bytes would not guarantee that the V
plane would fulfil this, e.g. a height of 650 lines would mean the V plane
buffer is not 32 byte aligned for YUV420 formats.
Having a Y stride of 64 bytes would ensure both U and V planes have a 32 byte
alignment, as the luma height will always be an even number of lines.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
vc04_services: isp: Report input node as wanting full range RAW color space
RAW color spaces are more usually reported as having full range
quantization.
Tested using libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
drivers: bcm2835_isp: Allow multiple users for the ISP driver.
Add a second (identical) set of device nodes to allow concurrent use of the ISP
hardware by another user. This change effectively creates a second state
structure (struct bcm2835_isp_dev) to maintain independent state for the second
user. Node and media entity names are appened with the instance index
appropriately.
Further users can be added by changing the BCM2835_ISP_NUM_INSTANCES define.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: bcm2835_isp: Fix div by 0 bug.
Fix a possible division by 0 bug when setting up the mmal port for the stats
port.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
staging/bcm2835-isp: Fix cleanup after init fail
bcm2835_isp_remove is called on an initialisation failure, but at that
point the drvdata hasn't been set. This causes a crash when e.g. using
the cutdown firmware (gpu_mem=16).
Move platform_set_drvdata before the instance probing loop to avoid the
problem.
See: https://github.com/raspberrypi/linux/issues/4774
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2835-v4l2-isp: Add missing lock initialization
ISP device allocation is dynamic hence the locks too.
struct mutex queue_lock is not initialized which result in bug.
Fixing same by initializing it.
[ 29.847138] INFO: trying to register non-static key.
[ 29.847156] The code is fine but needs lockdep annotation, or maybe
[ 29.847159] you didn't initialize this object before use?
[ 29.847161] turning off the locking correctness validator.
[ 29.847167] CPU: 1 PID: 343 Comm: v4l_id Tainted: G C 5.15.11-rt24-v8+ #8
[ 29.847187] Hardware name: Raspberry Pi 4 Model B Rev 1.4 (DT)
[ 29.847194] Call trace:
[ 29.847197] dump_backtrace+0x0/0x1b8
[ 29.847227] show_stack+0x20/0x30
[ 29.847240] dump_stack_lvl+0x8c/0xb8
[ 29.847254] dump_stack+0x18/0x34
[ 29.847263] register_lock_class+0x494/0x4a0
[ 29.847278] __lock_acquire+0x80/0x1680
[ 29.847289] lock_acquire+0x214/0x3a0
[ 29.847300] mutex_lock_nested+0x70/0xc8
[ 29.847312] _vb2_fop_release+0x3c/0xa8 [videobuf2_v4l2]
[ 29.847346] vb2_fop_release+0x34/0x60 [videobuf2_v4l2]
[ 29.847367] v4l2_release+0xc8/0x108 [videodev]
[ 29.847453] __fput+0x8c/0x258
[ 29.847476] ____fput+0x18/0x28
[ 29.847487] task_work_run+0x98/0x180
[ 29.847502] do_notify_resume+0x228/0x3f8
[ 29.847515] el0_svc+0xec/0xf0
[ 29.847523] el0t_64_sync_handler+0x90/0xb8
[ 29.847531] el0t_64_sync+0x180/0x184
Signed-off-by: Padmanabha Srinivasaiah <treasure4paddy@gmail.com>
staging: vc04_services: isp: Permit all sRGB colour spaces on ISP outputs
ISP outputs actually support all colour spaces that are fundamentally
sRGB underneath, regardless of whether an RGB or YUV output format is
actually requested.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
drivers: staging: bcm2835-isp: Do not cleanup mmal vcsm buffer on stop_streaming
On stop_streaming() the vcsm buffer handle gets released by the buffer cleanup
code. This will subsequently cause and error if userland re-queues the same
buffer on the next start_streaming() call.
Remove this cleanup code and rely on the vb2_ops->buf_cleanup() call to do the
cleanups instead.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: staging: bcm2835-isp: Clear LS table handle in the firmware
When all nodes have stopped streaming, ensure the firmware has released its
handle on the LS table dmabuf. This is done by passing a null handle in the
LS params.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: staging: bcm2835-isp: Respect caller's stride value
The stride value reported for output image buffers should be at least
as large as any value that was passed in by the caller (subject to
correct alignment for the pixel format). If the value is zero (meaning
no value was passed), or is too small, the minimum acceptable value
will be substituted.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
staging: vc04_services: bcm2835-isp: Drop include Makefile directive
Drop the include directive. They can break the build, when one only
wants to build a subdirectory. Replace with "../" for the includes in
the bcm2835-isp instead.
The fix is equivalent to the four patches between 29d49a76c5
("staging: vc04_services: bcm2835-audio: Drop include Makefile
directive")...2529ca211402 ("staging: vc04_services: interface: Drop
include Makefile directive")
Fixes: c8f89c9551c1 ("staging: vc04_services: ISP: Add a more complex ISP processing component")
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
staging: vc04_services: bcm2835-v4l2-isp: Register with vchiq_bus_type
Register the bcm2835-v4l2-isp driver with the vchiq_bus_type instead of
using the platform driver/device.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
staging: vc04_services: bcm2835-v4l2-isp: Explicitly set DMA mask
The platform model originally handled the DMA mask. Now that
we are on the vchiq_bus we need to explicitly set this.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
drivers: media: bcm2835_isp: Cache LS table dmabuf
Clients such as libcamera do not change the LS table dmabuf on every
frame. In such cases instead of mapping/remapping the same dmabuf on
every frame to send to the firmware, cache the dmabuf once and only
update and remap if the dmabuf has been changed by the userland client.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: bcm2835-unicam: Correctly handle error propagation for stream on
On a failure in start_streaming(), the error code would not propagate to
the calling function on all conditions. This would cause the userland
caller to not know of the failure.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: bcm2835-unicam: Return early from stop_streaming() if stopped
clk_disable_unprepare() is called unconditionally in stop_streaming().
This is incorrect in the cases where start_streaming() fails, and
unprepares all clocks as part of the failure cleanup. To avoid this,
ensure that clk_disable_unprepare() is only called in stop_streaming()
if the clocks are in a prepared state.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: bcm2835-unicam: Clear clock state when stopping streaming
Commit 65e08c4650 failed to clear the
clock state when the device stopped streaming. Fix this, as it might
again cause the same problems when doing an unprepare.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: bcm2835-unicam: Fix bug in buffer swapping logic
If multiple sets of interrupts occur simultaneously, it may be unsafe
to swap buffers, as the hardware may already be re-using the current
buffers. In such cases, avoid swapping buffers, and wait for the next
opportunity at the Frame End interrupt to signal completion.
Additionally, check the packet compare status when watching for frame
end for buffers swaps, as this could also signify a frame end event.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: bcm2835-unicam: Forward input status from subdevice
The vidioc_enum_input() v4l2 ioctl is capable of returning
sensor/input status as well. This is used in current
GStreamer HEAD for signal detection [1].
bcm2835-unicam does handle this syscall, but it didn't ask
the subdevice driver about the input status. The input then
appeared as always present.
This commit adds the necessary query. There is a precedent for
this - the R-Car VIN V4L2 driver does a similar call [2].
[1]: ce0be27caf/sys/v4l2/gstv4l2src.c (L553)
[2]: 7fb9d006d3/drivers/media/platform/rcar-vin/rcar-v4l2.c (L548)
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
media/bcm2835-unicam: Parse pad numbers correctly
The driver was making big assumptions about the source device
using pad 0 and 1, which doesn't follow for more complex
devices where Unicam's source device may be a sink device for
something else.
Read the pad numbers through media controller, and reference
them appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media/bcm2835-unicam: Add support for configuration via MC API
Adds Media Controller API support for more complex pipelines.
libcamera is about to switch to using this mechanism for configuring
sensors.
This can be enabled by either a module parameter, or device tree.
Various functions have been moved to group video-centric and
mc-centric functions together.
Based on a similar conversion done to ti-vpe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Fixup for 5.18 and new get_mbus_config struct
The number of active CSI2 data lanes has moved within the struct
v4l2_mbus_config used by the get_mbus_config API call.
Update the driver to match the changes in mainline.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drivers: bcm2835_unicam: Add logging message when a frame is dropped.
If a dummy buffer is still active on a frame start, it indicates that this frame
will be dropped. The explicit logging helps users identify performance issues.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: bcm2835_unicam: Disable trigger mode operation
On a Pi3 B/B+ platform the imx219 sensor frequently generates a single corrupt
frame when the sensor first starts. This can either be a missing line, or
invalid samples within the line. This only occurrs using the Unicam kernel
driver.
Disabling trigger mode elimiates this corruption. Since trigger mode is a
legacy feature copied from the firmware driver and not expected to be needed,
remove it. Tested on the Raspberry Pi cameras and shows no ill effects.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: bcm2835-unicam: Set ret on error path in unicam_async_complete()
Clang warns:
drivers/media/platform/bcm2835/bcm2835-unicam.c:3109:6: warning: variable 'ret' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (!source_pads) {
^~~~~~~~~~~~
drivers/media/platform/bcm2835/bcm2835-unicam.c:3152:9: note: uninitialized use occurs here
return ret;
^~~
drivers/media/platform/bcm2835/bcm2835-unicam.c:3109:2: note: remove the 'if' if its condition is always false
if (!source_pads) {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/bcm2835/bcm2835-unicam.c:3091:9: note: initialize the variable 'ret' to silence this warning
int ret;
^
= 0
1 warning generated.
When the if condition is true, ret will be used uninitialized, which
could result in undesirable behavior. Set ret to -ENODEV on the error
path, which is a standard error code for the ->complete() callback.
Fixes: d056e86eb3 ("media/bcm2835-unicam: Parse pad numbers correctly")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
media: bcm2835-unicam: Handle a repeated frame start with no end
In the case of 2 frame starts being received with no frame end
between, the queued buffer held in next_frm was lost as the
pointer was overwritten with the dummy buffer.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Correctly handle FS + FE ISR condtion
If we get a simultaneous FS + FE interrupt for the same frame, it cannot be
marked as completed and returned to userland as the framebuffer will be refilled
by Unicam on the next sensor frame. Additionally, the timestamp will be set to 0
as the FS interrupt handling code will not have run yet.
To avoid these problems, the frame is considered dropped in the FE handler,
and will be returned to userland on the subsequent sensor frame.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: bcm2835-unicam: Fix for possible dummy buffer overrun
The Unicam hardware has been observed to cause a buffer overrun when using the
dummy buffer as a circular buffer. The conditions that cause the overrun are not
fully known, but it seems to occur when the memory bus is heavily loaded.
To avoid the overrun, program the hardware with a buffer size of 0 when using
the dummy buffer. This will cause overrun into the allocated dummy buffer, but
avoid out of bounds writes.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: bcm2835-unicam: Fix up start/stop api change
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
media: bcm2835-unicam: Use mipi-csi2.h header for data type values
The MIPI CSI2 data type ID values are now defined in the
mipi-csi2.h header, so use those defines instead of hard
coding them in the driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Add support for RAW16 formats
With the RAW16 formats now having a defined CSI2 data type ID,
they can be added to the driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Start and stop media_pipeline with same node
media_pipeline_start and media_pipeline_stop now validate that
the pipeline is being started and stopped with the same pipe
and pad handles.
When running with embedded metadata (eg imx477 and imx708), the
start typically happens from the metadata pad, whilst stop is
always from the image pad.
Always pass the image pad to media_pipeline_start to ensure
that the calls are balanced.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drivers: media: bcm2835_unicam: Improve frame sequence count handling
Ensure that the frame sequence counter is incremented only if a previous
frame start interrupt has occurred, or a frame start + frame end has
occurred simultaneously.
This corresponds the sequence number with the actual number of frames
produced by the sensor, not the number of frame buffers dequeued back
to userland.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
bcm2835-unicam: hacks to allow it to build
media: bcm2835-unicam: Fix up async notifier usage
Fixes "8a090fc3e549 bcm2835-unicam: hacks to allow it to build"
media: bcm2835-unicam: Add option for a GPIO to reflect FS/FE timing
The legacy stack had an option to have a GPIO track frame start and
end events to give basic synchronisation to the incoming image stream.
https://forums.raspberrypi.com/viewtopic.php?t=190314
Replicate this in the kernel Unicam driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Add support for 12bit mono packed format
Now that V4L2_PIX_FMT_Y12P is defined, allow passing raw 12bit
mono packed data through the peripheral.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Add support for 14bit mono sources
Now that V4L2_PIX_FMT_Y14 and V4L2_PIX_FMT_Y14P are defined,
allow passing 14bit mono data through the peripheral.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Add support for unpacked 14bit Bayer formats
Now that the 14bit non-packed Bayer formats are defined, add them
into the supported formats lookup table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-unicam: Reinstate old downstream driver as legacy
Whilst the Unicam driver has now been upstreamed it only supports
configuration via Media Controller (not driven from the /dev/videoN
node), which makes life significantly harder for simple devices such
as mono sensors, and HDMI or analogue video to CSI2 bridge chips
(eg TC358743 and ADV7282M).
Fix up the downstream driver so that it builds, reinstate the links
from Kconfig and Makefile to it, and give it a new Kconfig name
(VIDEO_BCM2835_UNICAM_LEGACY).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Upstream Linux deems using output GPIOs to generate IRQs as a bogus
use case, even though the BCM2835 GPIO controller is capable of doing
so. A number of users would like to make use of this facility, so
disable the checks.
See: https://github.com/raspberrypi/linux/issues/2527
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
V4L2 wishes to have the codec header bytes in the same buffer as the
first encoded frame, so it does become 1-in 1-out for encoding.
The firmware now has an option to do this, so enable it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Add V4L2_META_FMT_BCM2835_ISP_STATS V4L2 format type.
This new format will be used by the BCM2835 ISP device to return
out ISP statistics for 3A.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
This patch adds MEDIA_BUS_FMT_SENSOR_DATA used by the bcm2835-unicam
driver to support CSI-2 embedded data streams from camera sensors.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add V4L2_META_FMT_SENSOR_DATA format 4CC.
This new format will be used by the BCM2835 Unicam device to return
out camera sensor embedded data.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Commit f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
amended of_spi_parse_dt() to always set SPI_CS_HIGH for SPI slaves whose
Chip Select is defined by a "cs-gpios" devicetree property.
This change breaks drivers whose probe functions set the mode field of
the spi_device because in doing so they clear the SPI_CS_HIGH flag.
Fix by setting SPI_CS_HIGH in spi_setup (under the same conditions as
in of_spi_parse_dt()).
See also: 83b2a8fe43 ("spi: spidev: Fix CS polarity if GPIO descriptors are used")
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
SQUASH: spi: Demote SPI_CS_HIGH warning to KERN_DEBUG
This warning is unavoidable from a client's perspective and
doesn't indicate anything wrong (just surprising).
SQUASH with "spi: use_gpio_descriptor fixup moved to spi_setup"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The DT bindings description of the Brcmstb PCIe device is described. This
node can be used by almost all Broadcom settop box chips, using
ARM, ARM64, or MIPS CPU architectures.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
A failure in gpiochip_irqchip_add leads to a leak of a gpiochip. Fix
the leak with the use of devm_gpiochip_add_data.
Fixes: 85ae9e512f ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcmn2835_isp is a platform driver dependent on vchiq,
therefore add the load/unload functions for it to vchiq.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
During a bulk transfer we request a DMA allocation to hold the
scatter-gather list. Most of the time, this allocation is small
(<< PAGE_SIZE), however it can be requested at a high enough frequency
to cause fragmentation and/or stress the CMA allocator (think time
spent in compaction here, or during allocations elsewhere).
Implement a pool to serve up small DMA allocations, falling back
to a coherent allocation if the request is greater than
VCHIQ_DMA_POOL_SIZE.
Signed-off-by: Oliver Gjoneski <ogjoneski@gmail.com>
The VCHIQ driver now loads the audio, camera, codec, and vc-sm
drivers as platform drivers. However they were not being given
the correct DMA configuration.
Call of_dma_configure with the parent (VCHIQ) parameters to be
inherited by the child.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
staging: vchiq: Use the old dma controller for OF config on platform devices
vchiq on Pi4 is no longer under the soc node, therefore it
doesn't get the dma-ranges for the VPU.
Switch to using the configuration of the old dma controller as
that will set the dma-ranges correctly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
staging: vchiq_arm: Give vchiq children DT nodes
vchiq kernel clients are now instantiated as platform drivers rather
than using DT, but the children of the vchiq interface may still
benefit from access to DT properties. Give them the option of a
a sub-node of the vchiq parent for configuration and to allow
them to be disabled.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
staging: vchiq_arm: Add 36-bit address support
Conditional on a new compatible string, change the pagelist encoding
such that the top 24 bits are the pfn, leaving 8 bits for run length
(-1), giving a 36-bit address range.
Manage the split between addresses for the VPU and addresses for the
40-bit DMA controller with a dedicated DMA device pointer that on non-
BCM2711 platforms is the same as the main VCHIQ device. This allows
the VCHIQ node to stay in the usual place in the DT.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
staging: vchiq_arm: children inherit DMA config
Although it is no longer necessary for vchiq's children to have a
different DMA configuration to the parent, they do still need to
explicitly to have their DMA configuration set - to be that of the
parent.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
BCM54213PE is an Ethernet PHY that supports PTP hardware timestamping.
BCM54210PW ia another Ethernet PHY, but one without PTP support.
Unfortunately the two PHYs return the same ID when queried, so some
extra information is required to determine whether the PHY is PTP-
capable.
There are two Raspberry Pi products that use these PHYs - Pi 4B and
CM4 - and fortunately they use different PHY addresses, so use that as
a differentiator. Choose to treat a PHY with the same ID but another
address as a BCM54210PE, which seems more common.
See: https://github.com/raspberrypi/linux/issues/5104
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
It's really a function of the board whether or not to use this feature
as it may require MAC compatibility as well as interop testing.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
The last nibble is a revision ID, and the 54213pe is a later rev
than the 54210e. Running the 54210e setup code on a 54213pe results
in a broken RGMII interface.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Add device tree entries and code to allow the specification of
the lighting modes for the LED's on the ethernet connector.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
net:phy:2711 Change the default ethernet LED actions
This should return default behaviour back to that of previous
releases.
net: phy: broadcom: Make LEDs 3+4 shadow LEDs 1+2
CM4 uses BCM54210PE, which supports 2 additional LEDs, choosing LED3
for the amber LED because it shows activity by default (LED4 is not
connected). However, this makes it uncontrollable by the eth_led<n>
dtparams which target LEDs 1+2.
Solve the problem by making LEDs 3+4 mirror LEDs 1+2 (which is much
simpler than adding baseboard-specific overrides, but comes with a
risk of making one of the LEDs redundant).
See: https://github.com/raspberrypi/linux/issues/5289
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the V4L2 codec driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the vcsm-cma driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The Infineon IRS1125 is a time of flight depth sensor that
has a CSI-2 interface.
Add a V4L2 subdevice driver for this device.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
media: irs1125: Using i2c_transfer for ic2 reads
Reading data over i2c is done by using i2c_transfer to ensure that this
operation can't be interrupted.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
media: irs1125: Refactoring and debug messages
Changed some variable names to comply with checkpatch --strict mode.
Debug messages added.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
media: irs1125: Atomic access to imager reconfiguration
Instead of changing the exposure and framerate settings for all sequences,
they can be changed for every sequence individually now. Therefore the
IRS1125_CID_SAFE_RECONFIG ctrl has been removed and replaced by
IRS1125_CID_SAFE_RECONFIG_S<seq_num>_EXPO and *_FRAME ctrls.
The consistency check in the sequence ctrl IRS1125_CID_SEQ_CONFIG
is removed.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
media: irs1125: Keep HW in sync after imager reset
When closing the video device, the irs1125 is put in power down state.
To keep V4L2 ctrls and the HW in sync, v4l2_ctrl_handler_setup is
called after power up.
The compound ctrl IRS1125_CID_MOD_PLL however has a default value
of all zeros, which puts the imager into a non responding state.
Thus, this ctrl is not written by the driver into HW after power up.
The userspace has to take care to write senseful data.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
media: i2c: add ov9281 driver.
Change-Id: I7b77250bbc56d2f861450cf77271ad15f9b88ab1
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
media: i2c: ov9281: fix mclk issue when probe multiple camera.
Takes the ov9281 part only from the Rockchip's patch.
Change-Id: I30e833baf2c1bb07d6d87ddb3b00759ab45a90e4
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
media: i2c: ov9281: add enum_frame_interval function for iq tool 2.2 and hal3
Adds the ov9281 parts of the Rockchip patch adding enum_frame_interval to
a large number of drivers.
Change-Id: I03344cd6cf278dd7c18fce8e97479089ef185a5c
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
media: i2c: ov9281: Fixup for recent kernel releases, and remove custom code
The Rockchip driver was based on a 4.4 kernel, and had several custom
Rockchip parts.
Update to 5.4 kernel APIs, with the relevant controls required by
libcamera, and remove custom Rockchip parts.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: ov9281: Read chip ID via 2 reads
Vision Components have made an OV9281 module which blocks reading
back the majority of registers to comply with NDAs, and in doing
so doesn't allow auto-increment register reading as used when
reading the chip ID.
Use two reads and manually combine the results.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: ov9281: Add support for 8 bit readout
The sensor supports 8 bit mode as well as 10bit, so add the
relevant code to allow selection of this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: ov9281: Add 1280x720 and 640x480 modes
Breaks out common register set and adds the different registers
for 1280x720 (cropped) and 640x480 (skipped) modes
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fixed picture line bug in all ov9281 modes
Signed-off-by: Mathias Anhalt <mathiasanhalt@web.de>
Added hflip and vflip controls to ov9281
Signed-off-by: Mathias Anhalt <mathiasanhalt@web.de>
media: i2c: ov9281: Remove override of subdev name
From the original Rockchip driver, the subdev was renamed
from the default to being "mov9281 <dev_name>" whereas the
default would have been "ov9281 <dev_name>".
Remove the override to drop back to the default rather than
a vendor custom string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: v4l2-subdev: add subdev-wide state struct
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
media: i2c: ov9281: Add fwnode properties controls
Add call to v4l2_ctrl_new_fwnode_properties to read and
create the fwnode based controls.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: ov9281: Sensor should report RAW color space
Tested on Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Partial revert "media: i2c: add ov9281 driver."
This partially reverts commit 84e98e3a4f.
The commit had merged some changes to other drivers with adding the ov9281
driver. Only the ov9281 parts have been reverted.
media: i2c: Update irs1125 Kconfig entry
Bring the IRS1125 Kconfig declaration in line with upstream entries.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add name for greyworld to white_balance preset names.
This patch previously applied to v4l2-ctrl.c but that was split
and deleted.
Signed-off-by: John Cox <jc@kynesim.co.uk>
This is mainly used for the NoIR camera which has no IR
filter and can completely confuse normal AWB presets.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Adds a simple greyworld white balance preset, mainly for use
with cameras without an IR filter (eg Raspberry Pi NoIR)
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
dt-bindings: media: i2c: Add IMX519 CMOS sensor binding
Add YAML device tree binding for IMX519 CMOS image sensor, and
the relevant MAINTAINERS entries.
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: Add driver for IMX519 sensor
Adds a driver for the 16MPix IMX519 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
4656x3496 10-bit @ 10fps
3840x2160 10-bit (cropped) @ 21fps
2328x1748 10-bit (binned) @ 30fps
1920x1080 10-bit (cropped/binned) @ 60fps
1280x720 10-bit (cropped/binned) @ 120fps
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: imx519: Advertise embedded data node on media pad 1
This commit updates the imx519 driver to adverise support for embedded
data streams.
The imx519 sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: imx519: Sensor should report RAW color space
Tested on Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: Update imx519 Kconfig entry
Bring the IMX519 Kconfig declaration in line with the upstream entries.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
media: i2c: Add PDAF support for IMX519
Add PDAF support for IMX519, and reduce the pixel rate to 426666667,
link freq to 408000000.
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
drivers: media: imx519: Add V4L2_CID_LINK_FREQ control
Add V4L2_CID_LINK_FREQ as a read-only control with a value of 408 Mhz.
This will be used by the CFE driver to corretly setup the DPHY timing
parameters in the CSI-2 block.
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
media: i2c: imx519: Squash fixes
Copying our downstream patch for imx477 that allows configuration
of external synchronisation signals via DT, add the same to imx296.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Through emperical testing, the sensor can crop upto a 96x88 window to
produce a valid Bayer frame. Adjust the ROIWH1_MIN ROIWV1_MIN
appropriately for this limit.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add support for setting horizontal and/or vertial flips in the IMX296
sensor through the V4L2_CID_HFLIP and V4L2_CID_VFLIP controls.
Add a new helper function to return the media bus format code that
depends on the sensor flips.
Grab the V4L2_CID_HFLIP and V4L2_CID_VFLIP controls on stream on, and
release on stream off to ensure flips cannot be changed while the sensor
is streaming.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Set the gain delay to 1 frame in the sensor. This avoids any race
condition or ambiguity over when the setting is applied through
userland.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add a helper function to setup the horizontal blanking control. Update
the control limits on set_format as the horizontal blanking time must
remain constant regardless of sensor output width.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Add a missing register write (MIPIC_AREA3W) when setting up a crop
window in the sensor to get this functionality working.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
In Fast Trigger mode (external shutter control), FE packet was
not sent at end of frame. Sony recommend this change to fix it.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Don't assume the camera has been reset each time we start streaming,
but always write registers relating to trigger_mode, even in mode 0.
IMX477: Stop driving XVS on stop streaming, to avoid spurious pulses.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Updated imx296 driver to support external trigger mode via XTR pin.
Added module parameter to control this mode.
Signed-off-by: Ben Benson <ben.benson@raspberrypi.com>
Disable enumerating and setting of the 2x2 binned mode entirely as it
does not seem to work for either mono or colour sensor variants.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
8 bit readout is only a reconfiguration of the CSI2 block,
and recomputation of horizontal blanking. Enable it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The sensor supports readout as 10 or 12 bit. As we are now
computing the horizontal blanking limits dynamically, adding
support for both readout modes falls out trivially, so add
them both.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The timing registers configured are for 450MHz.
If running at a different link frequency, use the automatic
timing control.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Now that the link frequency can be varied, write the link bit
rate registers to reflect the speed being used.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
As we now support variable link frequency, compute the minimum
line_length value that the sensor will work with, and set
V4L2_CID_HBLANK based on that number.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Rather than the hard coded PLL settings for fixed frequencies,
compute the PLL settings based on device tree, validating that
the specified rate can be achieved.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
There are a fair number of registers duplicated in all the mode
tables, so move those into the common table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This removes a load of boilerplate code around how registers
are grouped into multiple word values.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The frame length default value doesn't change dynamically, and
neither does any of the other parameters that configure it,
so precompute it instead of working from a frame duration to
get to the value.
The minimum value was also computed, when actually the sensor
will take any value down to 4 lines.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
line_length_pix is a value that the developer wants to know,
so write the values in decimal.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Register line_length_pix was being written by both the tables
of registers and the control handler for V4L2_CID_HBLANK.
Remove the duplication in the tables.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Copy the firmware's handling of FSTROBE, but using module parameters
instead of config.txt entries.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
dt-bindings: media: i2c: Add IMX477 CMOS sensor binding
Add YAML device tree binding for IMX477 CMOS image sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: Add driver for Sony IMX477 sensor
Adds a driver for the 12MPix Sony IMX477 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
4056x3040 12-bit @ 10fps
2028x1520 12-bit (binned) @ 40fps
2028x1050 12-bit (cropped/binned) @ 50fps
1012x760 10-bit (scaled) @ 120 fps
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Add support for adaptive frame control
Use V4L2_CID_EXPOSURE_AUTO_PRIORITY to control if the driver should
automatically adjust the sensor frame length based on exposure time,
allowing variable frame rates and longer exposures.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Return correct result on sensor id verification
The test should return -EIO if the register read id does not match
the expected sensor id.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Parse and register properties
Parse device properties and register controls for them using the V4L2
fwnode properties helpers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
media: i2c: imx477: Selection compliance fixes
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the imx477 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (8, 16) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
This commit mirrors 543790f777 done for
the imx219 sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Remove auto frame length adjusting
The V4L2_CID_EXPOSURE_AUTO_PRIORITY was used to let the sensor control
frame length (effectively framerate) based on the requested exposure
time requested. Remove this feature as it is never used, and goes
against how V4L2 likes to handle exposure and vblank controls.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Add very long exposure control to the driver
Add support for very long exposures by using the exposure multiplier
register. Userland does not need to pass any additional controls to
enable long exposures, it simply requests a larger vblank to extend the
exposure control range appropriately.
Currently, since hblank is fixed, a maximum of approximately 124 seconds
of exposure time can be used. In a future change, hblank could also be
controlled in userland to give over 200 seconds of exposure time.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Fix crop height for 2028x1080 mode
The crop height for this mode was set at 2600 lines, it should be 2160
lines instead.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Replace existing 1012x760 mode
The existing 1012x760 120 fps mode has significant IQ problem using
the internal sensor scaler. Replace this mode with a 1332x990 120 fps
mode instead. This new mode has a smaller field of view, but does not
suffer from the bad IQ of the original mode.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Remove internal v4l2_mbus_framefmt from the state
The only field in this struct that is used is the format code, so
replace the struct with this single field.
Save the format code in imx477_set_pad_format() when setting up a new
mode so that imx477_get_pad_format() performs the right lookup.
Otherwise, this caused a bug where the mode lookup occurred on the
12-bit table rather than the 10-bit table.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Remove unused function parameter
The struct imx477 *ctrl parameter is not used in the function
imx477_adjust_exposure_range(), so remove it.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Fix for long exposure limit calculations
Do not scale IMX477_EXPOSURE_OFFSET with the long exposure factor during
the limit calculations. This allows larger exposure times, and does seem to be
what the sensor is doing internally.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Extend driver to support imx378 sensor
The imx378 sensor is almost identical to the imx477 and can be
supported as a "compatible" sensor with just a few extra register
writes.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Fix framerates for 1332x990 mode
The imx477 driver's line length for this mode had not been updated to
the value supplied to us by the sensor manufacturer. With this
correction the sensor delivers the framerates that are expected.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Allow control of on-sensor DPC
A module parameter "dpc_enable" is added to allow the control of the
sensor's on-board DPC (Defective Pixel Correction) function.
This is a global setting to be configured before using the sensor;
there is no intention that this would ever be changed on-the-fly.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Sensor should report RAW color space
Tested on Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Add vsync trigger_mode parameter
trigger_mode == 0 (default) => no effect / no registers written
trigger_mode == 1 => source
trigger_mode == 2 => sink
This can be set e.g. in /boot/cmdline.txt as imx477.trigger_mode=N
Signed-off-by: Jonas Jacob <jonas.jacob@neocortexvision.com>
media: i2c: Update imx477 Kconfig entry
Bring the IMX477 Kconfig declaration in line with upstream entries.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
media: i2c: imx477: Correct minimum exposure lines
The minimum number of exposure lines value (IMX477_EXPOSURE_MIN) was
previously 20 but this is not correct. The datasheet is not completely
explicit, however the new value of 4 has been tested with all the
sensor modes supported by this driver, and matches the lowest exposure
value of 114us that could be achieved wtih Raspberry Pi's legacy
firmware driver.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Allow dynamic horizontal blanking control
Currently, the V4L2_CID_HBLANK control is marked as read-only. Remove this
restriction and allow userland to modify the control if needed.
Set the maximum limit of the line length to 0xfff0.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Reset hblank on mode switch
Reset the hblank control to the minimum value on every mode switch. This is to
account for userland instances that do not yet control hblank, otherwise it
gets set to a non-optimal value.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Do not unconditionally adjust hblank and vblank limits
On a mode change, only call imx477_set_framing_limits() to adjust the hblank
and vblank limits if the new mode is different from the existing mode. This
preserves any manual control values the user might have set.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
driver: media: i2c: imx477: Re-enable temperature sensor
The temperature sensor enable register write got lost at some point.
Re-enable it.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Fix locking in imx477_init_controls()
The driver does not lock the imx477 mutex when calling
imx477_set_framing_limits(), leading to:
WARNING: CPU: 3 PID: 426 at drivers/media/v4l2-core/v4l2-ctrls-api.c:934 __v4l2_ctrl_modify_range+0x1a0/0x210 [
videodev]
Fix this by taking the lock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
drivers: media: imx477: Disable the scaler
The horizontal scaler was enabled for the 2028x1520 and 2028x1080 modes,
with a scale factor of 1. It caused a single column of bad pixels on the
right edge of the image. Since scaling is not needed for these modes,
disable it entirely.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: imx477: Set horizontal binning when disabling the scaler
The horizontal scaler has been disabled but actually the sensor is not
binning horizontally, resulting in images that are stretched 2x
horizontally (missing the right half of the field of view completely).
Therefore we must additionally set the horizontal binning mode. There
is only marginal change in output quality and noise levels.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Fixes: f075893e9b ("drivers: media: imx477: Disable the scaler")
drivers: media: imx477: Add V4L2_CID_LINK_FREQ control
Add V4L2_CID_LINK_FREQ as a read-only control with a value of 450 Mhz.
This will be used by the CFE driver to corretly setup the DPHY timing
parameters in the CSI-2 block.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: imx477: Correctly set IMX477_PIXEL_RATE as a r/o control
This control is meant to be read-only, mark it as such.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: i2c: imx296,imx477: Configure tigger_mode every time
Don't assume the camera has been reset each time we start streaming,
but always write registers relating to trigger_mode, even in mode 0.
IMX477: Stop driving XVS on stop streaming, to avoid spurious pulses.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
media: i2c: imx477: Squash fixes
imx477: make trigger-mode more configurable
Allow trigger-mode to be overridden using device tree so that it can be
set per camera. Previously the mode could only be changed using a module
parameter, which would then affect all cameras.
Signed-off-by: Erik Botö <erik.boto@gmail.com>
drivers: media: imx477: Add V4L2_CID_LINK_FREQ control
Add V4L2_CID_LINK_FREQ as a read-only control with a value of 450 Mhz.
This will be used by the CFE driver to corretly setup the DPHY timing
parameters in the CSI-2 block.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Add options for slightly modifying the link freq
The default link frequency of 450MHz has been noted to interfere
with GPS if they are in close proximty.
Add the option for 453 and 456MHz to move the signal slightly out
of the band. (447MHz can not be offered as corruption is then observed
on the 133x992 10bit mode).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
fixup imx477 gps
media: i2c: imx477: Fix link frequency menu
"media: i2c: imx477: Add options for slightly modifying the link freq"
created a link frequency menu with 2 items in instead of one.
Correct this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx477: Add further link frequency options
https://github.com/raspberrypi/linux/issues/6004 reports further
issues with GPS interference.
Untested, but adds further link frequency options.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx477: Fix lockdep errors
imx477_get_format_code has a lockdep_assert_held test, however
the call paths from enum_mbus_code and enum_frame_size don't
lock the mutex before calling it.
Add in the relevant mutex locking.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: i2c: imx477: Disable temperature sensor when enabling XVS
On IMX477 it appears that the on-chip temperature sensor causes
XVS (external sync out) to pulse every ~2ms when not streaming.
So now we do a little dance: Temperature sensor is enabled during
common register setup, giving it time to warm up (almost literally;
otherwise the first frame's reading might be 0C), disabled before
enabling sync out, then enabled again once the camera is streaming.
We already took care to disable XVS output in stop_streaming()
(though previously it wasn't understood why this was needed).
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
media: i2c: Move Kconfig entry for IMX477 to the camera sensor section
It was accidentally placed in the audio decoder section.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Some combinations of Pi 4Bs and Ethernet switches don't reliably get a
DCHP-assigned IP address, leaving the unit with a self=assigned 169.254
address. In the failure case, the Pi is left able to receive packets
but not send them, suggesting that the MAC<->PHY link is getting into
a bad state.
It has been found empirically that skipping a reset step by the genet
driver prevents the failures. No downsides have been discovered yet,
and unlike the forced renegotiation it doesn't increase the time to
get an IP address, so the workaround is enabled by default; add
genet.skip_umac_reset=n
to the command line to disable it.
See: https://github.com/raspberrypi/linux/issues/3108
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
These wireless mouse/keyboard combo remote control devices specify
multiple "wheel" events in their report descriptors. The wheel events
are incorrectly defined and apparently map to accelerometer data, leading
to spurious mouse scroll events being generated at an extreme rate when
the device is moved.
As a workaround, use HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE to mask
feeding the extra wheel events to the input subsystem.
See: https://github.com/raspberrypi/firmware/issues/1189
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
The v3d driver currently encounters a lot of MMU PTE exceptions, so
only log the first to avoid swamping the kernel log.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
My various attempts at re-enabling runtime PM have failed, so just
crank the clock down when V3D is idle to reduce power consumption.
Signed-off-by: Eric Anholt <eric@anholt.net>
drm/v3d: Plug dma_fence leak
The irq_fence and done_fence are given a reference that is never
released. The necessary dma_fence_put()s seem to have been
deleted in error in an earlier commit.
Fixes: 0b73676836b2 ("drm/v3d: Clock V3D down when not in use.")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
v3d_drv: Handle missing clock more gracefully
Signed-off-by: popcornmix <popcornmix@gmail.com>
v3d_gem: Kick the clock so firmware knows we are using firmware clock interface
Setting the v3d clock to low value allows firmware to handle dvfs in case
where v3d hardware is not being actively used (e.g. console use).
Signed-off-by: popcornmix <popcornmix@gmail.com>
drm/v3d: Switch clock setting to new api
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
drm/v3d: Convert to new clock range API
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
drm/v3d: Correct clock settng calls to new APIs
There was a report that 6.12 kernel has lower benchmark
scores than 6.6.
I can confirm, and found it started with 6.8 kernel
which moved some code into a new file (v3d_submit.c)
and in two places the change to the clock api were missed.
The effect of the bug is the v3d clock sometimes
unwantedly drops to a lower rate.
With this patch the benchmark scores are good again.
Fixes: 86963038cb
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
drm/v3d: CPU job submissions shouldn't affect V3D GPU clock
We can avoid calling the v3d_clock_up_put and v3d_clock_up_get
when a job is submitted to a CPU queue. We don't need to change
the V3D core frequency to run a CPU job as it is executed on
the CPU. This way we avoid delaying timestamps CPU jobs by 4.5ms
that is the time that it takes the firmware to increase the V3D
core frequency.
Fixes: fe6a858096 ("drm/v3d: Correct clock settng calls to new APIs")
Signed-off-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
The BCM2835 I2C blocks have a register to set the clock-stretch
timeout - how long the device is allowed to hold SCL low - in bus
cycles. The current driver doesn't write to the register, therefore
the default value of 64 cycles is being used for all devices.
Set the timeout to the value recommended for SMBus - 35ms.
See: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
i2c: bcm2835: Make clock-stretch timeout configurable
The default clock-stretch timeout is 35 mS, which works well for
SMBus, but there are some I2C devices which can stretch the clock even
longer. Rather than trying to prescribe a safe default for everyone,
allow the timeout to be configured.
Signed-off-by: Alex Crawford <raspberrypi/linux@code.acrawford.com>
i2c-bcm2835: Flush FIFOs cleanly on error
On error condition, note the error return code, but still
handle the FIFOs in the normal way rather than relying on
C_CLEAR flushing everything cleanly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
i2c-bcm2835: Do not abort transfers on ERR if still active
If a transaction is aborted immediately on ERR being reported,
then the bus is not returned to the STOP condition, and devices
generally get very upset.
Handle the ERR and CLKT conditions only when TA is not set.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
i2c-bcm2835: Implement I2C_M_IGNORE_NAK
Now that transfers aren't aborted immediately (and uncleanly) on
errors, and the FIFOs are always drained after all transfers, we
can implement I2C_M_IGNORE_NAK by ignoring the returned error
value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Make the BCM2711 a different machine, but keep it in board_bcm2835.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
arm: bcm2835: Add bcm2838 compatible string.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ARM: bcm: Switch board, clk and pinctrl to bcm2711 compatible
After the decision to use bcm2711 compatible for upstream, we should
switch all accepted compatibles to bcm2711. So we can boot with
one DTB the down- and the upstream kernel.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Setting both the Drop and Add bits on the input context prevents the
corruption of split transactions seen with the BCM2711 XHCI controller,
which is a dwc3 variant.
This is a downstream feature that allows usbhid to restrict polling
intervals on mice and keyboards, and was only tested on a VL805 which
didn't complain about the fact the endpoint got added twice.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
See https://github.com/raspberrypi/linux/issues/3981
An unknown unsafe memory access can result in the ep_state variable
in xhci_virt_ep being trampled with a stuck SET_DEQ_PENDING state
despite successful completion of a Set TR Deq Pointer command.
All URB enqueue/dequeue calls for the endpoint will fail in this state
so no transfers are possible until the device is reconnected.
As a workaround, clear the flag if we see it set and issue a new Set
TR Deq command anyway - this should be harmless, as a prior Set TR Deq
command will only have been issued in the Stopped state, and if the
endpoint is Running then the controller is required to ignore it and
respond with a Context State Error event TRB.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Must be called in a non-atomic context, after the endpoint
has been registered with the hardware via xhci_add_endpoint
and before the first URB is submitted for the endpoint.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
xHCI caches device and endpoint data after the interface is configured,
so an explicit command needs to be issued for any device driver wanting
to alter the polling interval of an endpoint.
Add usb_fixup_endpoint() to allow drivers to do this. The fixup must be
called after calculating endpoint bandwidth requirements but before any
URBs are submitted.
If polling intervals are shortened, any bandwidth reservations are no
longer valid but in practice polling intervals are only ever relaxed.
Limit the scope to interrupt transfers for now.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
There are several warts surrounding bcmgenet_mii_probe() as this
function is called from ndo_open, but it's calling registration-type
functions. The probe should be called at probe time and refactored
such that the PHY device data can be extracted to limit the scope
of this flag to Broadcom PHYs.
For now, pass this flag in as it puts our attached PHY into a low-power
state when disconnected.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Set defaults for TX and RX packet coalescing to be equivalent to:
# ethtool -C eth0 tx-frames 10
# ethtool -C eth0 rx-usecs 50
This may be something we want to set via DT parameters in the
future.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The HWRNG on the BCM2838 is compatible to iproc-rng200, so add the
support to this driver instead of bcm2835-rng.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
hwrng: iproc-rng200: Correct SoC name
The Pi 4 SoC is called BCM2711, not BCM2838.
Fixes: "hwrng: iproc-rng200: Add BCM2838 support"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The legacy peripherals can only address the first gigabyte of RAM, so
ensure that DMA allocations are restricted to that region.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The ioremapping creates mappings within the vmalloc area. The
equivalent early function, create_mapping, now checks that the
requested explicit virtual address is between VMALLOC_START and
VMALLOC_END. As there is no reason to have any correlation between
the physical and virtual addresses, put the required mappings at
VMALLOC_START and above.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The logic to drive the data line high to implement a strong pullup
assumed that the pin was already an output - setting a value does
not change an input.
See: https://github.com/raspberrypi/firmware/issues/1143
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
drivers: w1-gpio: add flag to force read-polling while delaying
On Pi 5, the link to RP1 will bounce in and out of L1 depending on
inactivity timers at both the RC and EP end. Unfortunately for
bitbashing 1-wire, this means that on an otherwise idle Pi 5 many of the
reads/writes to GPIO registers are delayed by up to 8us which causes
mis-sampling of read data and trashes write bits.
By issuing dummy reads at a rate greater than the link inactivity
timeout while spinning on a delay, PCIe stays in L0 which does not incur
additional latency.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: w1-gpio: Fixup uninitialised variable use in w1_gpio_probe
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
On error, vchiq_mmal_component_init could leave the
event context allocated for ports.
Clean them up in the error path.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
vchiq_mmal_component_init calls init_event_context for the
control port, but vchiq_mmal_component_finalise didn't free
it, causing a memory leak..
Add the free call.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
mmal_parameters.h hasn't been updated to reflect additions made
over the last few years. Update it to reflect the currently
supported parameters.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The list of formats was copied before Bayer support was added.
The ISP supports Bayer and is being supported by the bcm2835_codec
driver, so add in the encodings for them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The MMAL client_component field is used with the event
mechanism to allow the client to identify the component for
which the event is generated.
The field is only 32bits in size, therefore we can't use a
pointer to the component in a 64 bit kernel.
Component handles are already held in an array per VCHI
instance, so use the array index as the client_component handle
to avoid having to create a new IDR for this purpose.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
videobuf2 only allowed exporting a dmabuf as a file descriptor,
but there are instances where having the struct dma_buf is
useful within the kernel.
Split the current implementation into two, one step which
exports a struct dma_buf, and the second which converts that
into an fd.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Add the ability to send data to ports. This only supports
zero copy mode as the required bulk transfer setup calls
are not done.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
(Preparation for the codec driver).
The codec uses the event mechanism to report things such as
resolution changes. It is signalled by the cmd field of the buffer
being non-zero.
Add support for passing this information out to the client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Fixes up a checkpatch error "Avoid using bool structure members
because of possible alignment issues".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Document the DT bindings for the CSI2/CCP2 receiver peripheral
(known as Unicam) on BCM283x SoCs.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Acked-by: Rob Herring <robh@kernel.org>
dt-bindings: bcm2835-unicam: Update documentation with new clock params
Update the documentation to reflect the new "VPU" clock needed
by the bcm2835-unicam driver.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
New helper defines that allow printing of a FOURCC using
printf(V4L2_FOURCC_CONV, V4L2_FOURCC_CONV_ARGS(fourcc));
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The ADV7282M can support YPbPr on AIN1-3, but this was
not selectable from the driver. Add it to the list of
supported input modes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The hardware default is differential CVBS on AIN1 & 2, which
isn't very useful.
Select the first input that is defined as valid for the
chip variant (typically CVBS_AIN1).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The bInterval is set to 4 (i.e. 8 microframes => 1ms) and the only bit
that the driver pays attention to is "link was reset". If there's a
flapping status bit in that endpoint data, (such as if PHY negotiation
needs a few tries to get a stable link) then polling at a slower rate
would act as a de-bounce.
See: https://github.com/raspberrypi/linux/issues/2447
Ethernet cables with faulty or missing pairs (specifically pairs C and
D) allow auto-negotiation to 1000Mbs, but do not support the successful
establishment of a link. Add a DT property, "microchip,downshift-after",
to configure the number of auto-negotiation failures after which it
falls back to 100Mbs. Valid values are 2, 3, 4, 5 and 0, where 0 means
never downshift.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The driver already reported the firmware build date during probe.
The mailbox calls have been extended to also report the variant
1 = standard start.elf
2 = start_x.elf (includes camera stack)
3 = start_db.elf (includes assert logging)
4 = start_cd.elf (cutdown version for smallest memory footprint).
Log the variant during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
firmware: raspberrypi: Report the fw git hash during probe
The firmware can now report the git hash from which it was built
via the mailbox, so report it during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ad83c7cb2f ("irqchip/irq-bcm2836: Add support for DT interrupt polarity")
changed the way that the BCM2836/7 local interrupts are mapped; instead
of being pre-mapped they are now mapped on-demand. A side effect of this
change is that the call to irq_of_parse_and_map from armctrl_of_init
creates a new mapping, forming a gap between the IRQs and the FIQs. This
gap breaks the FIQ<->IRQ mapping which up to now has been done by assuming:
1) that the value of FIQ_START is the same as the number of normal IRQs
that will be mapped (still true), and
2) that this value is also the offset between an IRQ and its equivalent
FIQ (which is no longer the case).
Remove both assumptions by measuring the interval between the last IRQ
and the last FIQ, passing it as the parameter to init_FIQ().
Fixes: https://github.com/raspberrypi/linux/issues/2432
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Register for reboot notifications, sending RPI_FIRMWARE_NOTIFY_REBOOT
over the mailbox interface on reception.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reduces overhead when using X
usbhid: call usb_fixup_endpoint after mangling intervals
Lets the mousepoll override mechanism work with xhci.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
I2C busses can be assigned specific bus numbers using aliases in
Device Tree - string properties where the name is the alias and the
value is the path to the node. The current DT parameter mechanism
does not allow property names to be derived from a parameter value
in any way, so it isn't possible to generate unique or matching
aliases for nodes from an overlay that can generate multiple
instances, e.g. i2c-gpio.
Work around this limitation (at least temporarily) by allowing
the i2c adapter number to be initialised from the "reg" property
if present.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
There is a new test in __irq_startup that the IRQ is activated, which
hasn't been the case for FIQs since they bypass some of the usual setup.
Augment enable_fiq to include a call to irq_activate to avoid the
warning.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Create a semi-static mapping for the USB registers early in the boot
process, before additional kernel threads are started, so all threads
will have the mappings from the start. This avoids the need for
data aborts to lazily update them.
See: https://github.com/raspberrypi/linux/issues/2450
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Uses the debugfs I/F to provide access to the AXI
bus performance monitors.
Requires the new mailbox peripheral access for access
to the VPU performance registers, system bus access
is done using direct register reads.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
raspberrypi_axi_monitor: suppress warning
Suppress the following warning by casting the pointer to and uintptr_t
before to u32:
Signed-off-by: Matteo Croce <mcroce@redhat.com>
perf/raspberry: Add support for 2712 axi performance monitors
Also handle 2711 correctly which has a different configuration
from 2835.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
IRQ-CPU mapping is round robined on ARM64 to increase
concurrency and allow multiple interrupts to be serviced
at a time. This reduces the need for FIQ.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
drivers: irqchip: irq-bcm2835: Concurrency fix
The commit shown in Fixes: aims to improve interrupt throughput by
getting the handlers invoked on different CPU cores. It does so (*) by
using an irq_ack hook to change the interrupt routing.
Unfortunately, the IRQ status bits must be cleared at source, which only
happens once the interrupt handler has run - there is no easy way for
one core to claim one of the IRQs before sending the remainder to the
next core on the list, so waking another core immediately results in a
race with a chance of both cores handling the same IRQ. It is probably
for this reason that the routing change is deferred to irq_ack, but that
doesn't guarantee no clashes - after irq_ack is called, control returns
to bcm2836_chained_handler_irq which proceeds to check for other pending
IRQs at a time when the next core is probably doing the same thing.
Since the whole point of the original commit is to distribute the IRQ
handling, there is no reason to attempt to handle multiple IRQs in one
interrupt callback, so the problem can be solved (or at least made much
harder to reproduce) by changing a "while" into an "if", so that each
invocation only handles one IRQ.
(*) I'm not convinced it's as effective as claimed since irq_ack is
called _after_ the interrupt handler, but the author thought it made a
difference.
See: https://github.com/raspberrypi/linux/issues/5214https://github.com/raspberrypi/linux/pull/1794
Fixes: fd4c9785bd ("ARM64: Round-Robin dispatch IRQs between CPUs.")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
irqchip: irq-bcm2836: Avoid prototype warning
Declare bcm2836_arm_irqchip_spin_gpu_irq in irq-bcm2836.h to avoid a
compiler warning about a missing prototype.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: Fix build errors on other platforms
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: fix build error
There is an error when compiling rpi-4.6.y branch:
CC drivers/of/configfs.o
drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.default_groups = of_cfs_def_groups,
^
drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next')
The .default_groups is linked list since commit
1ae1602de0.
This commit uses configfs_add_default_group to fix this problem.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
configfs: New of_overlay API
of: configfs: Use of_overlay_fdt_apply API call
The published API to the dynamic overlay application mechanism now
takes a Flattened Device Tree blob as input so that it can manage the
lifetime of the unflattened tree. Conveniently, the new API call -
of_overlay_fdt_apply - is virtually a drop-in replacement for
create_overlay, which can now be deleted.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add a virtual GPIO driver that uses the firmware mailbox interface to
request that the VPU toggles LEDs.
gpio: bcm-virt: Fix the get() method
The get() method does not understand the on-the-wire encoding of the
remote GPIO states, thinking they are simple on/off bits when they are
really pairs of 16-bit counts. Rewrite the get() handler to return the
value last written, which will eventually match the actual GPIO state
if there are no other changes.
See: https://github.com/raspberrypi/linux/issues/4638
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2835-virtgpio: Update for Linux 6.6
The gpio subsystem is happier if the gpiochip is given a parent, and
if it doesn't have a fixed base gpio number. While we're in here,
use the fact that the firmware node is the parent to locate it,
and use the devm_ version of rpi_firmware_get.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
Add Raspberry Pi firmware driver to the dependencies of backlight driver
Otherwise the backlight driver fails to build if the firmware
loading driver is not in the kernel
Signed-off-by: Alex Riesen <alexander.riesen@cetitec.com>
ASoC: Add support for Rpi-DAC
ASoC: Add prompt for ICS43432 codec
Without a prompt string, a config setting can't be included in a
defconfig. Give CONFIG_SND_SOC_ICS43432 a prompt so that Pi soundcards
can use the driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add IQaudIO Sound Card support for Raspberry Pi
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
IQaudIO: auto-mute for AMP+ and DigiAMP+
IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.
Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."
Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
dtoverlay=iqaudio-dacplus,unmute_amp
"one-shot" unmute when kernel module loads.
dtoverlay=iqaudio-dacplus,auto_mute_amp
Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
when ALSA device closed. (Re-opening the device within the 5 second close
window, will cancel mute.)
Revision 4, using gpiod.
Revision 5, clean-up formatting before adding mute code.
- Convert tab plus 4 space formatting to 2x tab
- Remove '// NOT USED' commented code
Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: iqaudio-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: iqaudio-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Added support for HiFiBerry DAC+
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Fixed a bug when using 352.8kHz sample rate
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
ASoC: pcm512x: revert downstream changes
This partially reverts commit 185ea05465
which was added by https://github.com/raspberrypi/linux/pull/1152
The downstream pcm512x changes caused a regression, it broke normal
use of the 24bit format with the codec, eg when using simple-audio-card.
The actual bug with 24bit playback is the incorrect usage
of physical_width in various drivers in the downstream tree
which causes 24bit data to be transmitted with 32 clock
cycles. So it's not the pcm512x that needs fixing, it's the
soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
hifiberry_dacplus: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add driver for rpi-proto
Forward port of 3.10.x driver from https://github.com/koalo
We are using a custom board and would like to use rpi 3.18.x
kernel. Patch works fine for our embedded system.
URL to the audio chip:
http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/
Playback tested with devicetree enabled.
Signed-off-by: Waldemar Brodkorb <wbrodkorb@conet.de>
ASoC: rpi-proto: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add Support for JustBoom Audio boards
justboom-dac: Adjust for ALSA API change
As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card *
rather than a struct snd_soc_codec *.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: justboom-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params as it's no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: justboom-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
New AudioInjector.net Pi soundcard with low jitter audio in and out.
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
Added support for headphones, microphone and bclk_ratio settings.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
ASoC: audioinjector-pi-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
New driver for RRA DigiDAC1 soundcard using WM8741 + WM8804
ASoC: digidac1-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Dion Audio LOCO DAC-AMP HAT
Using dedicated machine driver and pcm5102a codec driver.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: dionaudio_loco: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Allo Piano DAC boards: Initial 2 channel (stereo) support (#1645)
Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
machine driver.
NB. The initial support is 2 channel (stereo) ONLY!
(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
pending an update to the upstream pcm512x codec driver, which will have
to be submitted via upstream. With the initial downstream support,
provided by this patch, the Piano DAC 2.1 subwoofer outputs will
not function.)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Signed-off-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
ASoC: allo-piano-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-piano-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Piano DAC 2.1 plus add-on board for Raspberry Pi.
The Piano DAC 2.1 has support for 4 channels with subwoofer.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Add clock changes and mute gpios (#1938)
Also improve code style and adhere to ALSA coding conventions.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
PianoPlus: Dual Mono & Dual Stereo features added (#2069)
allo-piano-dac-plus: Master volume added + fixes
Master volume added, which controls both DACs volumes.
See: https://github.com/raspberrypi/linux/pull/2149
Also fix initial max volume, default mode value, and unmute.
Signed-off-by: allocom <sparky-dev@allo.com>
ASoC: allo-piano-dac-plus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: bcm: Fix memset dereference warning
This warning appears with GCC 6.4.0 from toolchains.bootlin.com:
../sound/soc/bcm/allo-piano-dac-plus.c: In function ‘snd_allo_piano_dac_init’:
../sound/soc/bcm/allo-piano-dac-plus.c:711:30: warning: argument to ‘sizeof’ in ‘memset’ call is the same expression as the destination; did you mean to dereference it? [-Wsizeof-pointer-memaccess]
memset(glb_ptr, 0x00, sizeof(glb_ptr));
^
Suggested-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
ASoC: allo-piano-dac-plus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Boss DAC add-on board for Raspberry Pi. (#1924)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
Add support for new clock rate and mute gpios.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
ASoC: allo-boss-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
allo-boss-dac: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Support for Blokas Labs pisound board
Pisound dynamic overlay (#1760)
Restructuring pisound-overlay.dts, so it can be loaded and unloaded dynamically using dtoverlay.
Print a logline when the kernel module is removed.
pisound improvements:
* Added a writable sysfs object to enable scripts / user space software
to blink MIDI activity LEDs for variable duration.
* Improved hw_param constraints setting.
* Added compatibility with S16_LE sample format.
* Exposed some simple placeholder volume controls, so the card appears
in volumealsa widget.
Add missing SND_PISOUND selects dependency to SND_RAWMIDI
Without it the Pisound module fails to compile.
See https://github.com/raspberrypi/linux/issues/2366
Updates for Pisound module code:
* Merged 'Fix a warning in DEBUG builds' (1c8b82b).
* Updating some strings and copyright information.
* Fix for handling high load of MIDI input and output.
* Use dual rate oversampling ratio for 96kHz instead of single
rate one.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fixing memset call in pisound.c
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound's MIDI Input getting blocked for a while in rare cases.
There was a possible race condition which could lead to Input's FIFO queue
to be underflown, causing high amount of processing in the worker thread for
some period of time.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound kernel module in Real Time kernel configuration.
When handler of data_available interrupt is fired, queue_work ends up
getting called and it can block on a spin lock which is not allowed in
interrupt context. The fix was to run the handler from a thread context
instead.
Pisound: Remove spinlock usage around spi_sync
ASoC: pisound: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: pisound: fix the parameter for spi_device_match
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add driver for Cirrus Logic Audio Card
Note: due to problems with deferred probing of regulators
the following softdep should be added to a modprobe.d file
softdep arizona-spi pre: arizona-ldo1
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: rpi-cirrus: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: Support for Dion Audio LOCO-V2 DAC-AMP HAT
Signed-off-by: Miquel Blauw <info@dionaudio.nl>
ASoC: dionaudio_loco-v2: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: dionaudio_loco-v2: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Fe-Pi audio sound card. (#1867)
Fe-Pi Audio Sound Card is based on NXP SGTL5000 codec.
Mechanical specification of the board is the same the Raspberry Pi Zero.
3.5mm jacks for Headphone/Mic, Line In, and Line Out.
Signed-off-by: Henry Kupis <fe-pi@cox.net>
ASoC: fe-pi-audio: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for the AudioInjector.net Octo sound card
AudioInjector Octo: sample rates, regulators, reset
This patch adds new sample rates to the Audioinjector Octo sound card. The
new supported rates are (in kHz) :
96, 48, 32, 24, 16, 8, 88.2, 44.1, 29.4, 22.05, 14.7
Reference the bcm270x DT regulators in the overlay.
This patch adds a reset GPIO for the AudioInjector.net octo sound card.
Audioinjector octo : Make the playback and capture symmetric
This patch ensures that the sample rate and channel count of the audioinjector
octo sound card are symmetric.
audioinjector-octo: Add continuous clock feature
By user request, add a switch to prevent the clocks being stopped when
the stream is paused, stopped or shutdown. Provide access to the switch
by adding a 'non-stop-clocks' parameter to the audioinjector-addons
overlay.
See: https://github.com/raspberrypi/linux/issues/2409
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
sound: Fixes for audioinjector-octo under 4.19
1. Move the DT alias declaration to the I2C shim in the cases
where the shim is enabled. This works around a problem caused by a
4.19 commit [1] that generates DT/OF uevents for I2C drivers.
2. Fix the diagnostics in an error path of the soundcard driver to
correctly identify the reason for the failure to load.
3. Move the declaration of the clock node in the overlay outside
the I2C node to avoid warnings.
4. Sort the overlay nodes so that dependencies are only to earlier
fragments, in an attempt to get runtime dtoverlay application to
work (it still doesn't...)
See: https://github.com/Audio-Injector/Octo/issues/14
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
[1] af503716ac ("i2c: core: report OF style module alias for devices registered via OF")
ASoC: audioinjector-octo-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Driver support for Google voiceHAT soundcard.
ASoC: googlevoicehat-codec: Use correct device when grabbing GPIO
The fixup for the VoiceHAT in 4.18 incorrectly tried to find the
sdmode GPIO pin under the card device, not the codec device.
This failed, and therefore caused the device probe to fail.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Reformat for kernel coding standards
Fix all whitespace, indentation, and bracing errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Make driver function structure const
Make voicehat_component_driver a const structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Only convert from ms to jiffies once
Minor optimisation and allows to become checkpatch clean.
A msec value is read out of DT or from a define, and convert once to
jiffies, rather than every time that it is used.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Driver and overlay for Allo Katana DAC
Allo Katana DAC: Updated default values
Signed-off-by: Jaikumar <jaikumar@cem-solutions.com>
Added mute stream func
Signed-off-by: Jaikumar <jaikumar@cem-solutions.net>
codecs: Correct Katana minimum volume
Update Katana minimum volume to get the exact 0.5 dB value in each step.
Signed-off-by: Sudeep Kumar <sudeepkumar@cem-solutions.net>
ASoC: Add generic RPI driver for simple soundcards.
The RPI simple sound card driver provides a generic ALSA SOC card driver
supporting a variety of Pi HAT soundcards. The intention is to avoid
the duplication of code for cards that can't be fully supported by
the soc simple/graph cards but are otherwise almost identical.
This initial commit adds support for the ADAU1977 ADC, Google VoiceHat,
HifiBerry AMP, HifiBerry DAC and RPI DAC.
Signed-off-by: Tim Gover <tim.gover@raspberrypi.org>
ASoC: Use correct card name in rpi-simple driver
Use the specific card name from drvdata instead of the snd_rpi_simple
rpi-simple-soundcard: Use nicer driver name "RPi-simple"
Rename the driver from "RPI simple soundcard" to "RPi-simple" so that
the driver name won't be mangled allowing to be used unaltered as the
card conf filename.
ASoC: rpi-simple-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add Kconfig and Makefile for sound/soc/bcm
Signed-off-by: popcornmix <popcornmix@gmail.com>
ASoC: Create a generic Pi Hat WM8804 driver
Reduce the amount of duplicated code by creating a generic driver for
Pi Hat digi cards using the WM8804 codec.
This replaces the
Allo DigiOne, Hifiberry Digi/Pro, JustBoom Digi and IQAudIO Digi
dedicate soundcard drivers with a generic driver.
There are no significant changes to the runtime behavior of the drivers
and end users should not have to change any configuration settings
after upgrading.
Minor changes
* Check the return value of snd_soc_component_update_bits
* Added some pr_debug tracing
* Various checkpatch tidyups
* Updated allodigi-one to use use 128FS at > 96 Khz. This appears to
be an omission in the original driver code so followed the Hifiberry
DAC driver approach.
ASoC: rpi-wm8804-soundcard: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: drop PWRDN register writes
Since kernel 4.0 the PWRDN register bits are under DAPM
control from the wm8804 driver.
Drop code that modifies that register to avoid interfering
with DAPM.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: configure wm8804 clocks only on rate change
This should avoid clicks when stopping and immediately afterwards
starting a stream with the same samplerate as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: Fixed MCLKDIV for Allo Digione
The Allo Digione board wants a fixed MCLKDIV of 256.
See: https://github.com/raspberrypi/linux/issues/3296
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: Add support for AudioSense-Pi add-on soundcard
AudioSense-Pi is a RPi HAT based on a TI's TLV320AIC32x4 stereo codec
This hardware provides multiple audio I/O capabilities to the RPi.
The codec connects to the RPi's SoC through the I2S Bus.
The following devices can be connected through a 3.5mm jack
1. Line-In: Plain old audio in from mobile phones, PCs, etc.,
2. Mic-In: Connect a microphone
3. Line-Out: Connect the output to a speaker
4. Headphones: Connect a Headphone w or w/o microphones
Multiple Inputs:
It supports the following combinations
1. Two stereo Line-Inputs and a microphone
2. One stereo Line-Input and two microphones
3. Two stereo Line-Inputs, a microphone and
one mono line-input (with h/w hack)
4. One stereo Line-Input, two microphones and
one mono line-input (with h/w hack)
Multiple Outputs:
Audio output can be routed to the headphones or
speakers (with additional hardware)
Signed-off-by: b-ak <anur.bhargav@gmail.com>
ASoC: audiosense-pi: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added driver for the HiFiBerry DAC+ ADC (#2694)
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
hifiberry_dacplusadc: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: fix DAI link setup
The driver only defines a single DAI link and the code that tries
to setup the second (non-existent) DAI link looks wrong - using dmic
as a CPU/platform driver doesn't make any sense.
The DT overlay doesn't define a dmic property, so the code was never
executed (otherwise it would have resulted in a memory corruption).
So drop the offending code to prevent issues if a dmic property
should be added to the DT overlay.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Audiophonics I-Sabre 9038Q2M DAC driver
Signed-off-by: Audiophonics <contact@audiophonics.fr>
ASoC: i-sabre-q2m: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added IQaudIO Pi-Codec board support (#2969)
Add support for the IQaudIO Pi-Codec board.
Signed-off-by: Gordon <gordon@iqaudio.com>
Fixed 48k timing issue
ASoC: iqaudio-codec: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
adds the Hifiberry DAC+ADC PRO version
This adds the driver for the DAC+ADC PRO version of the Hifiberry soundcard with software controlled PCM1863 ADC
Signed-off-by: Joerg Schambacher joerg@i2audio.com
Add Hifiberry DAC+DSP soundcard driver (#3224)
Adds the driver for the Hifiberry DAC+DSP. It supports capture and
playback depending on the DSP firmware.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Allow simultaneous use of JustBoom DAC and Digi
Signed-off-by: Johannes Krude <johannes@krude.de>
Pisound: MIDI communication fixes for scaled down CPU.
* Increased maximum SPI communication speed to avoid running too slow
when the CPU is scaled down and losing MIDI data.
* Keep track of buffer usage in millibytes for higher precision.
Signed-off-by: Giedrius Trainavičius <giedrius@blokas.io>
sound: Add the HiFiBerry DAC+HD version
This adds the driver for the DAC+HD version supporting HiFiBerry's
PCM179x based DACs. It also adds PLL control for clock generation.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Fix master mode settings of HiFiBerry DAC+ADC PRO card (#3424)
This patch fixes the board DAI setting when in master-mode.
Wrong setting could have caused random pop noise.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC PRO sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+/DAC+PRO sound cards
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
pisound: Added reading Pisound board hardware revision and exposing it (#3425)
pisound: Added reading Pisound board hardware revision and exposing it in kernel log and sysfs file:
/sys/kernel/pisound/hw_version
Signed-off-by: Giedrius <giedrius@blokas.io>
Added driver for HiFiBerry Amp amplifier add-on board
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
According to 5713 pdf doc CLOCK_CTRL is a readonly status register, and it behaves so. Remove useless setting
sound: pcm512x-codec: Adding 352.8kHz samplerate support
sound/soc: only first codec is master in multicodec setup
When using multiple codecs, at most one codec should generate the master
clock. All codecs except the first are therefore configured for slave
mode.
Signed-off-by: Johannes Krude <johannes@krude.de>
ASoC: Fix snd_soc_get_pcm_runtime usage
Commit [1] changed the snd_soc_get_pcm_runtime to take a dai_link
pointer instead of a string. Patch up the downstream drivers to use
the modified API.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 4468189ff3 ("ASoC: soc-core: find rtd via dai_link pointer at snd_soc_get_pcm_runtime()")
Add support for the AudioInjector.net Isolated sound card
This patch adds support for the Audio Injector Isolated sound card.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Add support for merus-amp soundcard and ma120x0p codec
Add 96KHz rate support to MA120X0P codec and make enable and mute gpio
pins optional.
Signed-off-by: AMuszkat <ariel.muszkat@gmail.com>
Fixes a problem with clock settings of HiFiBerry DAC+ADC PRO (#3545)
This patch fixes a problem of the re-calculation of
i2s-clock and -parameter settings when only the ADC is activated.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
configs: Enable the AD193x codecs
See: https://github.com/raspberrypi/linux/issues/2850
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Switch to snd_soc_dai_set_bclk_ratio
Replaces obsolete function snd_soc_dai_set_tdm_slot
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Enhances the DAC+ driver to control the optional headphone amplifier
Probes on the I2C bus for TPA6130A2, if successful, it sets DT-parameter
'status' from 'disabled' to 'okay' using change_sets to enable
the headphone control.
Signed-off-by: Joerg Schambacher joerg@i2audio.com
Update Allo Piano Dac Driver
Add unique names to the individual dac coded drivers
Remove some of the codec controls that are not used.
Signed-off-by: Paul Hermann <paul@picoreplayer.org>
Fixes an onboard clock detection problem of the PRO versions
Increasing the sleep time after clock selection to 3-4ms
allows the correct detection of all combinations of DAC+ Pro
and DAC+ADC Pro sound cards and the various PI revisions.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
ASoC:ma120x0p: Increase maximum sample rate to 192KHz
Change the maximum sample rate for the amplifier to
192KHz as given in the Infineon specification.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
ASoC: ma120x0p: Remove unnecessary const specifier
Clang warns:
sound/soc/codecs/ma120x0p.c:891:14: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
static const SOC_VALUE_ENUM_SINGLE_DECL(pwr_mode_ctrl,
^
./include/sound/soc.h:362:2: note: expanded from macro 'SOC_VALUE_ENUM_SINGLE_DECL'
SOC_VALUE_ENUM_DOUBLE_DECL(name, xreg, xshift, xshift, xmask, xtexts, xvalues)
^
./include/sound/soc.h:359:2: note: expanded from macro 'SOC_VALUE_ENUM_DOUBLE_DECL'
const struct soc_enum name = SOC_VALUE_ENUM_DOUBLE(xreg, xshift_l, xshift_r, xmask, \
^
1 warning generated.
SOC_VALUE_ENUM_DOUBLE_DECL already has a const specifier. Remove the duplicate
const to clean up the warning.
Fixes: 42444979e7 ("Add support for all the downstream rpi sound card drivers")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
ASoC: bcm: allo-piano-dac-plus: Remove unnecessary const specifiers
Clang warns:
sound/soc/bcm/allo-piano-dac-plus.c:66:14: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(allo_piano_mode_enum,
^
./include/sound/soc.h:355:2: note: expanded from macro 'SOC_ENUM_SINGLE_DECL'
SOC_ENUM_DOUBLE_DECL(name, xreg, xshift, xshift, xtexts)
^
./include/sound/soc.h:352:2: note: expanded from macro 'SOC_ENUM_DOUBLE_DECL'
const struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
^
sound/soc/bcm/allo-piano-dac-plus.c:75:14: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(allo_piano_dual_mode_enum,
^
./include/sound/soc.h:355:2: note: expanded from macro 'SOC_ENUM_SINGLE_DECL'
SOC_ENUM_DOUBLE_DECL(name, xreg, xshift, xshift, xtexts)
^
./include/sound/soc.h:352:2: note: expanded from macro 'SOC_ENUM_DOUBLE_DECL'
const struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
^
sound/soc/bcm/allo-piano-dac-plus.c:96:14: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(allo_piano_enum,
^
./include/sound/soc.h:355:2: note: expanded from macro 'SOC_ENUM_SINGLE_DECL'
SOC_ENUM_DOUBLE_DECL(name, xreg, xshift, xshift, xtexts)
^
./include/sound/soc.h:352:2: note: expanded from macro 'SOC_ENUM_DOUBLE_DECL'
const struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
^
3 warnings generated.
SOC_VALUE_ENUM_DOUBLE_DECL already has a const specifier. Remove the duplicate
const specifiers to clean up the warnings.
Fixes: 42444979e7 ("Add support for all the downstream rpi sound card drivers")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
rpi-simple-soundcard: Add Dion Audio KIWI streamer
Signed-off-by: Miquel Blauw <miquelblauw@hotmail.com>
rpi-simple-soundcard: adds definitions for the HiFiBerry AMP3 card
Uses Infineon MA120x0 amplifier and supports full sample rate of 192ksps.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
sound: soc: bcm: Added Sound card driver for Dacberry400 Audio card for Raspberry Pi 400
Added Sound card driver for DACberry400 Audio card.
Signed-off-by: Ashish Vara <ashishhvara@gmail.com>
ASoC:ma120x0p: Corrects the volume level display
Fixes the wrongly changed 'limiter volume' display back to -50dB minimum
and sets the correct minimum volume level to -144dB to be aligned with
the controls and display in alsamixer etc.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
ASoC: bcm: Fix Rpi-PROTO and audioinjector.net Pi
As of kernel 5.19 the WM8731 driver has separate I2C and SPI support
modules. Change the Kconfig definitions for the audioinjector.net Pi
and Rpi-PROTO soundcards to select SND_SOC_WM8731_I2C.
See: https://github.com/raspberrypi/linux/issues/5364
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: adau1977: Add correct compatible strings
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: bcm2835-i2s: Use phys addresses for DAI DMA
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
rpi sound cards: Fix Codec Zero rate switching
The Raspberry Pi Codec Zero (and IQaudIO Codec) don't notify the DA7213
codec when it needs to change PLL frequencies. As a result, audio can
be played at the wrong rate - play a 48kHz sound immediately after a
44.1kHz sound to see the effect, but in some configurations the codec
can lock into the wrong state and always get some rates wrong.
Add the necessary notification to fix the issue.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: dwc: Support set_bclk_ratio
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: dwc: Add DMACR handling
Add control of the DMACR register, which is required for paced DMA
(i.e. DREQ) support.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASOC: dwc: Improve DMA shutdown
Disabling the I2S interface with outstanding transfers prevents the
DMAC from shutting down, so keep it partially active after a stop.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASOC: dwc: Fix 16-bit audio handling
IMO the Synopsys datasheet could be clearer in this area, but it seems
that the DMA data ports (DMATX and DMARX) expect left and right samples
in alternate writes; if a stereo pair is pushed in a single 32-bit
write, the upper half is ignored, leading to double speed audio with a
confused stereo image. Make sure the necessary changes happen by
updating the DMA configuration data in the hw_params method.
The set_bclk_ratio change was made at a time when it looked like it
could be causing an error, but I think the division of responsibilities
is clearer this way (and the kernel log clearer without the info-level
message).
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: bcm: Remove dependency on BCM2835 I2S
These soundcard drivers don't rely on a specific I2S interface, so
remove the dependency declarations.
See: https://github.com/raspberrypi/linux-2712/issues/111
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: bcm: audioinjector_octo: Add soundcard "owner"
See: https://github.com/raspberrypi/linux/issues/5697
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Pisound: Don't export the button GPIO via sysfs GPIO class.
Signed-off-by: Giedrius Trainavičius <giedrius@blokas.io>
Pisound: Read out the SPI speed to use from the Device Tree.
Signed-off-by: Giedrius Trainavičius <giedrius@blokas.io>
ASoC: DACplus - fix 16bit sample support in clock consumer mode
The former code did not adjust the physical sample width when
in clock consumer mode and has taken the fixed 32 bit default.
This has caused the audio to be played at half its frequency due to
the fixed bclk_ratio of 64.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
ASoC: adds support for AMP4 Pro to the DAC Plus driver
The AMP4 Pro is a I2S master mode capable amplifier with
clean onboard clock generators.
We can share the card driver between TAS575x amplifiers
and the PCM512x DACs as they are SW compatible.
From a HW perspective though we need to limit the sample
rates to the standard audio rates to avoid running the
onboard clocks through the PLL. Using the PLL would require
even a different HW.
DAI/stream name are also set accordingly to allow the user
a convenient identification of the soundcard
Needs the pcm512x driver with TAS575x support (already in
upstream kernel).
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
ASoC: DACplusADCPro - fix 16bit sample support in clock consumer mode
The former code did not adjust the physical sample width when in
clock consumer mode and has taken the fixed 32 bit default. This
has caused the audio to be played at half its frequency due to
the fixed bclk_ratio of 64.
Problem appears only on PI5 as on the former PIs the I2S module
did simply run at fixed 64x rate.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
Impliment driver support for Interlude Audio Digital Hat
Implementing driver support for
Interlude audio's WM8805 based digital hat
by leveraging existing drivers
ASOc: Add HiFiBerry DAC8X to the simple card driver
Defines the settings for the 8 channel version of the standard
DAC by overwriting the number of channels in the DAI defs.
It can run in 8ch mode only on PI5 using the 4 lane data output
of the designware I2S0 module.
Signed-off-by: j-schambacher <joerg@hifiberry.com>
ASoC: bcm: Use the correct sample width value
ALSA's concept of the physical width of a sample is how much memory it
occupies, including any padding. This not the same as the count of bits
of actual sample content. In particular, S24_LE has a width of 24 bits
but a physical width of 32 bits because there is a byte of padding with
each sample.
When calculating bclk_ratio, etc., it is width that matters, not
physical width. Correct the error that has been replicated across the
drivers for many Raspberry Pi-compatible soundcards.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: dwc: Correct channel count reporting
The DWC I2S driver treats the channel count register values as if they
encode a power of two (2, 4, 8, 16), but they actually encode a
multiple of 2 (2, 4, 6, 8).
Also improve the error message when asked for an unsupported number
of channels.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: Fix 16bit sample support for Hifiberry DACplusADC
Same issue as #5919.
'width' needs to be set independent of clocking mode.
Signed-off-by: j-schambacher <joerg@hifiberry.com>
allo-boss-dac mute output when changing parameters
Since I noticed that sometimes changing sample rates causes some digital
quirks and noises, I've changed the function to mute the output before
performing the changes and then unmute it when an error occurs or the
parameters got set.
Signed-off-by: Alessandro Marcon <marconalessandro04@gmail.com>
ASoC: bcm: Use power-of-2 bclk_ratios
The soundcard drivers originally used snd_pcm_format_physical_width,
but a later commit changed that to snd_pcm_format_width because the
in-memory sample storage width should not be a factor in determining
the bclk_ratio. However, the physical width rounds the sample bits up
to the nearest power of 2, which makes it easier to find integer clock
divisors.
Restore the old behaviour, but with an implementation that makes it
clear what is going on.
See: https://github.com/raspberrypi/linux/issues/6104
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: bcm: Add "owner" info for more soundcards
See: https://github.com/raspberrypi/linux/issues/5697
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: da7213: Add a set_bclk_ratio method
Following [1], it becomes harder for the CPU DAI to know the correct
BCLK ratio. We can either bake the same knowledge into the sound card
driver, or implement and use set_bclk_ratio on the codec. This commit
does the latter.
[1] commit c89e652e84 ("ASoC: da7213: Add support for mono, set
frame width to 32 when possible")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
iqaudio-codec: Use the codec's new set_bclk_ratio
To ensure that the CPU DAI and codec agree over the BCLK ratio, impose
a fixed value of 64 on both of them.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: add driver for new HiFiBerry ADC only board(s)
Adds the driver for the soon to be released first ADC only board.
It includes the same ADC controls as used by the DAC+ADC Pro driver.
Signed-off-by: j-schambacher <joerg@hifiberry.com>
ASoC: add HiFiBerry ADC8x 8-channel ADC to simple-card-driver
Definitions for the 8 channel ADC card. The card uses only
HW-controlled devices which allows the uses of the 'dummy-dai'.
It will run only on a PI5 as it requires the designware I2S0 module.
The necessary output lanes I2S0_DI[0..3] are claimed from within the
DT overlay.
Signed-off-by: j-schambacher <joerg@hifiberry.com>
sound/soc: dwc-i2s: choose FIFO thresholds based on DMA burst constraints
Valid ranges for the I2S peripheral's FIFO configuration include a depth
of 16 - unconditionally setting the burst length to 16 with a fifo
threshold of size/2 will cause under/overflows.
For DMA engines with restricted capabilities the requested burst length
and FIFO thresholds need to be adjusted downward accordingly.
Both the RX and TX FIFOs operate on "less-than" thresholds. Setting the
TX threshold to fifo_size minus burst means the FIFO is kept nearly-full.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
ASoC: allo-piano-dac-plus: Fix volume limit locking
Calling snd_soc_limit_volume from within a kcontrol put handler seems
to cause a deadlock as it attempts to claim a write lock that is already
held. Call snd_soc_limit_volume from the main initialisation code
instead, to avoid the recursive locking.
See: https://github.com/raspberrypi/linux/issues/6527
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: allo-piano-dac-plus: Suppress -517 errors
Use dev_err_probe to simplify the code and suppress EPROBE_DEFER errors.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
soc: pcm3168a: Add DT binding to force clock consumer mode
ASoC cannot configure the codec correctly when the ADC and DAC share clock
lines and one of them is the clock producer. Add a DT binding that
overrides ASoC and forces the component into clock consumer mode.
Signed-off-by: Stephen Gordon <gordoste@iinet.net.au>
ASoC: pcm512x: Demote "No SCLK" to debug level
Designing a PCM512X-based soundcard with no external SCLK is a valid
choice supported by the driver. Don't alarm users with messages that
say "No SCLK, using BCLK: -2" - reclassify them as debug information.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: allo-piano-dac-plus: Fix volume limiting
Controls which only exist when snd_soc_register_card returns can't be
modified before then. Move the setting of volume limits to just before
the end of the probe function.
Link: https://github.com/raspberrypi/linux/issues/6527
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: allo-piano-dac-plus: Remove pointless code
The codec control Digital Playback Volume is one of the controls deleted
by the allo-piano-dac-plus driver. It is effectively replaced by the
soundcard controls Master Playback Volume and Subwoofer Playback Volume.
Delete the code that sets the volume limit on those codec controls - the
limits on the soundcard volume controls are sufficient.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: adds ADC8x support to the Hifiberry DAC8x
The driver probes for the ADC8x which can be stacked on top
of the DAC8x. It enables a symmetric 8 channel capture using
the dummy-dai.
Signed-off-by: j-schambacher <joerg@hifiberry.com>
sound: soc: raspberrypi: RP1 Audio Out driver as an ASOC DAI
Only 48000Hz stereo 16-bit output is currently supported.
It requires some additional OF plumbing to connect it to a
"dummy" codec and generic sound card.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Adding Pimidi kernel module.
Signed-off-by: Giedrius Trainavičius <giedrius@blokas.io>
Adding Pisound Micro kernel module
Signed-off-by: Giedrius Trainavičius <giedrius@blokas.io>
Pisound Micro: Fix for MIDI output under full load.
This fixes MIDI output of Pisound Micro after running for a while under
full load and increases timing stability.
Signed-off-by: Giedrius Trainavičius <giedrius@blokas.io>
ALSA: korg1212: replace del_timer with timer_delete
pisound-micro: Added pin_pull and pin_b_pull sysfs attributes for Pisound Micro.
These attributes are available only for GPIO input and Encoder elements.
Signed-off-by: Giedrius <giedrius@blokas.io>
Pisound Micro: Workaround for snd_soc_dai_set_tdm_slot with slots=0
Even though it's documented that specifying slots=0 can be used to disable
the TDM mode, error checking introduced in 6.12.31 version broke this,
therefore, for the time being, a workaround is to provide a xlate_tdm_slot_mask
operation implementation to return 0 instead of -EINVAL as it does in case
slots argument is 0.
Signed-off-by: Giedrius Trainavičius <giedrius@blokas.io>
Upstream chose to use BTN_DPAD_* and BTN_SELECT, whilst downstream
had used KEY_*.
Revert to the downstream map to avoid any regressions.
(Ideally this would be read from DT)
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This patch adds the compatible string for the Sense HAT device to
the list of compatible strings in the simple_mfd_i2c driver so that
it can match against the device and load its children and their drivers
Co-developed-by: Mwesigwa Guma <mguma@redhat.com>
Signed-off-by: Mwesigwa Guma <mguma@redhat.com>
Co-developed-by: Joel Savitz <jsavitz@redhat.com>
Signed-off-by: Joel Savitz <jsavitz@redhat.com>
Signed-off-by: Charles Mirabile <cmirabil@redhat.com>
mfd: Add rpi_sense_core of compatible string
rpisense-fb: Set pseudo_pallete to prevent crash on fbcon takeover
Signed-off-by: Serge Schneider <serge@raspberrypi.com>
rpisense-fb: Add explicit fb_deferred_io_mmap hook
As of commit [1], introduced in 5.18, fbdev drivers that use
deferred IO and need mmap support must include an explicit fb_mmap
pointer to the fb_deferred_io_mmap.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 5905585103 ("fbdev: Put mmap for deferred I/O into drivers")
drivers: Remove downstream SenseHAT core and joystick drivers
Parts of a SenseHAT driver have been submitted upstream using the
simple-i2c-mfd framework. The joystick driver has been merged.
It's been noted that there are several issues with the downstream
joystick and core drivers, so remove these in favour of the upstream
approach, and fix up the FB driver to match.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Provide a __copy_from_user that uses memcpy. On BCM2708, use
optimised memcpy/memmove/memcmp/memset implementations.
arch/arm: Add mmiocpy/set aliases for memcpy/set
See: https://github.com/raspberrypi/linux/issues/1082
copy_from_user: CPU_SW_DOMAIN_PAN compatibility
The downstream copy_from_user acceleration must also play nice with
CONFIG_CPU_SW_DOMAIN_PAN.
See: https://github.com/raspberrypi/linux/issues/1381
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Fix copy_from_user if BCM2835_FAST_MEMCPY=n
The change which introduced CONFIG_BCM2835_FAST_MEMCPY unconditionally
changed the behaviour of arm_copy_from_user. The page pinning code
is not safe on ARMv7 if LPAE & high memory is enabled and causes
crashes which look like PTE corruption.
Make __copy_from_user_memcpy conditional on CONFIG_2835_FAST_MEMCPY=y
which is really an ARMv6 / Pi1 optimization and not necessary on newer
ARM processors.
arm: fix mmap unlocks in uaccess_with_memcpy.c
This is a regression that was added with the commit 192a4e923e as of rpi-5.8.y, since that is when the move to the mmap locking API was introduced - d8ed45c5dc
The issue is that when the patch to improve performance for the __copy_to_user and __copy_from_user functions were added for the Raspberry Pi, some of the mmaps were incorrectly mapped to write instead of read. This would cause a verity of issues, and in my case, prevent the booting of a squashfs filesystem on rpi-5.8-y and above. An example of the panic you would see from this can be seen at https://pastebin.com/raw/jBz5xCzL
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Christopher Blake <chrisrblake93@gmail.com>
arch/arm: Add __memset alias to memset_rpi.S
memset_rpi.S is an optimised memset implementation, but doesn't define
__memset (which was just added to memset.S). As a result, building
for the BCM2835 platform causes a link failure.
Add __memset as yet another alias to our common implementation.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
arm: Fix custom rpi __memset32 and __memset64
See: https://github.com/raspberrypi/linux/issues/4798
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
arm: Fix annoying .eh_frame section warnings
Replace the cfi directives with the UNWIND equivalents. This prevents
the .eh_frame section from being created, eliminating the warnings.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The "input" trigger makes the associated GPIO an input. This is to support
the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
N.B. pwr_led is not available on Model A or B boards.
leds-gpio: Implement the brightness_get method
The power LED uses some clever logic that means it is driven
by a voltage measuring circuit when configured as input, otherwise
it is driven by the GPIO output value. This patch wires up the
brightness_get method for leds-gpio so that user-space can monitor
the LED value via /sys/class/gpio/led1/brightness. Using the input
trigger this returns an indication of the system power health,
otherwise it is just whatever value the trigger has written most
recently.
See: https://github.com/raspberrypi/linux/issues/1064
Support booting without Device Tree.
Turn on USB power.
Load driver early because of lacking support for deferred probing
in many drivers.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
firmware: bcm2835: Don't turn on USB power
The raspberrypi-power driver is now used to turn on USB power.
This partly reverts commit:
firmware: bcm2835: Support ARCH_BCM270x
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Based on bcm2835-gpiomem.
We allow export of the "GPIO registers" to userspace via a chardev as
this allows for finer access control (e.g. users must be group gpio, root
not required).
This driver allows access to either rp1-gpiomem or gpiomem, depending on
which nodes are populated in devicetree.
RP1 has a different look-and-feel to BCM283x SoCs as it has split ranges
for IO controls and the parallel registered OE/IN/OUT access. To handle
this, the driver concatenates the ranges for an IO bank and the
corresponding RIO instance into a contiguous buffer.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Add module for accessing the mailbox property channel through
/dev/vcio. Was previously in bcm2708-vcio.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
char: vcio: Add compat ioctl handling
There was no compat ioctl handler, so 32 bit userspace on a
64 bit kernel failed as IOCTL_MBOX_PROPERTY used the size
of char*.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
char: vcio: Fail probe if rpi_firmware is not found.
Device Tree is now the only supported config mechanism, therefore
uncomment the block of code that fails the probe if the
firmware node can't be found.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
drivers: char: vcio: Use common compat header
The definition of compat_ptr is now common for most platforms, but
requires the inclusion of <linux/compat.h>.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
char: vcio: Rewrite as a firmware node child
The old vcio driver is a simple character device that manually locates
the firmware driver. Initialising it before the firmware driver causes
a failure, and no retries are attempted.
Rewrite vcio as a platform driver that depends on a DT node for its
instantiation and the location of the firmware driver, making use of
the miscdevice framework to reduce the code size.
N.B. Using miscdevice changes the udev SUBSYSTEM string, so a change
to the companion udev rule is required in order to continue to set
the correct device permissions, e.g.:
KERNEL="vcio", GROUP="video", MODE="0660"
See: https://github.com/raspberrypi/linux/issues/4620
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
See: https://github.com/raspberrypi/linux/issues/260
i2c-bcm2708/BCM270X_DT: Add support for I2C2
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)
* i2c: fix i2c_bcm2708: Clear FIFO before sending data
Make sure FIFO gets cleared before trying to send
data in case of a repeated start (COMBINED=Y).
* i2c: fix i2c_bcm2708: Only write to FIFO when not full
Check if FIFO can accept data before writing.
To avoid a peripheral read on the last iteration of a loop,
both bcm2708_bsc_fifo_fill and ~drain are changed as well.
Signed-off-by: Luke Wren <wren6991@gmail.com>
MISC: bcm2835: smi: use clock manager and fix reload issues
Use clock manager instead of self-made clockmanager.
Also fix some error paths that showd up during development
(especially missing release of dma resources on rmmod)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
bcm2835_smi: re-add dereference to fix DMA transfers
bcm2835_smi_dev: Fix handling of word-odd lengths
The read and write functions did not use the correct pointer offset
when dealing with an odd number of bytes after a DMA transfer. Also,
only handle the remaining odd bytes if the DMA transfer completed
successfully.
Submitted-by: @madimario (GitHub)
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
misc: bcm2835_smi: Use proper enum types for dma_{,un}map_single()
Clang warns:
drivers/misc/bcm2835_smi.c:692:4: warning: implicit conversion from enumeration type 'enum dma_transfer_direction' to different enumeration type 'enum dma_data_direction' [-Wenum-conversion]
DMA_MEM_TO_DEV);
^~~~~~~~~~~~~~~
./include/linux/dma-mapping.h:406:66: note: expanded from macro 'dma_map_single'
#define dma_map_single(d, a, s, r) dma_map_single_attrs(d, a, s, r, 0)
~~~~~~~~~~~~~~~~~~~~ ^
drivers/misc/bcm2835_smi.c:705:35: warning: implicit conversion from enumeration type 'enum dma_transfer_direction' to different enumeration type 'enum dma_data_direction' [-Wenum-conversion]
(inst->dev, phy_addr, n_bytes, DMA_MEM_TO_DEV);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~
./include/linux/dma-mapping.h:407:70: note: expanded from macro 'dma_unmap_single'
#define dma_unmap_single(d, a, s, r) dma_unmap_single_attrs(d, a, s, r, 0)
~~~~~~~~~~~~~~~~~~~~~~ ^
drivers/misc/bcm2835_smi.c:751:12: warning: implicit conversion from enumeration type 'enum dma_transfer_direction' to different enumeration type 'enum dma_data_direction' [-Wenum-conversion]
DMA_DEV_TO_MEM);
^~~~~~~~~~~~~~~
./include/linux/dma-mapping.h:406:66: note: expanded from macro 'dma_map_single'
#define dma_map_single(d, a, s, r) dma_map_single_attrs(d, a, s, r, 0)
~~~~~~~~~~~~~~~~~~~~ ^
drivers/misc/bcm2835_smi.c:761:50: warning: implicit conversion from enumeration type 'enum dma_transfer_direction' to different enumeration type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_single(inst->dev, phy_addr, n_bytes, DMA_DEV_TO_MEM);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~
./include/linux/dma-mapping.h:407:70: note: expanded from macro 'dma_unmap_single'
#define dma_unmap_single(d, a, s, r) dma_unmap_single_attrs(d, a, s, r, 0)
~~~~~~~~~~~~~~~~~~~~~~ ^
4 warnings generated.
Use the proper enumerated type to clear up the warning. There is not
actually a bug here because the enumerated types have the same integer
value:
DMA_MEM_TO_DEV = DMA_TO_DEVICE = 1
DMA_DEV_TO_MEM = DMA_FROM_DEVICE = 2
Fixes: 93254d0f7b ("Add SMI driver")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
bcm2835-smi: Use phys addresses for slave DMA config
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: popcornmix <popcornmix@gmail.com>
BCM270x: Move vc_mem
Make the vc_mem module available for ARCH_BCM2835 by moving it.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
char: vc_mem: Fix up compat ioctls for 64bit kernel
compat_ioctl wasn't defined, so 32bit user/64bit kernel
always failed.
VC_MEM_IOC_MEM_PHYS_ADDR was defined with parameter size
unsigned long, so the ioctl cmd changes between sizes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
char: vc_mem: Fix all coding style issues.
Cleans up all checkpatch errors in vc_mem.c and vc_mem.h
No functional change to the code.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
char: vc_mem: Delete dead code
There are no error exists once device_create has succeeded, and
therefore no need to call device_destroy from vc_mem_init.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
char: broadcom: vc_mem: Fix preprocessor conditional
Signed-off-by: Alexander Winkowski <dereference23@outlook.com>
vc_mem: Add the DMA memcpy support from bcm2708_fb
bcm2708_fb is disabled by the vc4-kms-v3d overlay, which means that the
DMA memcpy support it provides is not available to allow vclog to read
the VC logs from the top 16MB on Pi 2 and Pi 3. Add the code to the
vc_mem driver, which will still be enabled.
It ought to be possible to do a proper DMA_MEM_TO_MEM copy via the
generic DMA customer API, but that can be a later step.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
See https://github.com/raspberrypi/linux/issues/5019
If an SD card has degraded performance such that IO operations time out
then the MMC block layer will leak SG DMA mappings in the swiotlb during
recovery. It retries the same SG and this causes the leak, as it is
mapped twice - once in sdhci_pre_req() and again during single-block
reads in sdhci_prepare_data().
Resetting the card (including power-cycling if a regulator for vmmc is
present) ought to be enough to recover a stuck state, so for now don't
try single-block reads in the recovery path.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Reported/Tested-by: Gellert Weisz <gellert@raspberrypi.org>
mmc: bcm2835-mmc: enable DT support for all architectures
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Enable Device Tree support for all architectures.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
mmc: bcm2835-mmc: fix probe error handling
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Add locks when accessing sdhost registers
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-mmc entry
Add Device Tree entry for bcm2835-mmc.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Don't overwrite MMC capabilities from DT
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: New timer API
mmc: bcm2835-mmc: Support underclocking
Support underclocking of the SD bus using the max-frequency DT property
(which currently has no DT parameter). The sd_overclock parameter
already provides another way to achieve the same thing which should be
equivalent in end result, but it is a bug not to support max-frequency
as well.
See: https://github.com/raspberrypi/linux/issues/2350
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc/bcm2835: Recover from MMC_SEND_EXT_CSD
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
N.B. This workaround was essentially discovered by accident and without
a full understanding the inner workings of the controller, so it is
fortunate that the "fix" only modifies error paths.
See: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: Fix DMA channel leak
The BCM2835 MMC host driver requests a DMA channel on probe but neglects
to release the channel in the probe error path and on driver unbind.
I'm seeing this happen on every boot of the Compute Module 3: On first
driver probe, DMA channel 2 is allocated and then leaked with a "could
not get clk, deferring probe" message. On second driver probe, channel 4
is allocated.
Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Fix struct mmc_host leak on probe
The BCM2835 MMC host driver requests the bus address of the host's
register map on probe. If that fails, the driver leaks the struct
mmc_host allocated earlier.
Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Fix duplicate free_irq() on remove
The BCM2835 MMC host driver requests its interrupt as a device-managed
resource, so the interrupt is automatically freed after the driver is
unbound.
However on driver unbind, bcm2835_mmc_remove() frees the interrupt
explicitly to avoid invocation of the interrupt handler after driver
structures have been torn down.
The interrupt is thus freed twice, leading to a WARN splat in
__free_irq(). Fix by not requesting the interrupt as a device-managed
resource.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Handle mmc_add_host() errors
The BCM2835 MMC host driver calls mmc_add_host() but doesn't check its
return value. Errors occurring in that function are therefore not
handled. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Deduplicate reset of driver data on remove
The BCM2835 MMC host driver sets the device's driver data pointer to
NULL on ->remove() even though the driver core subsequently does the
same in __device_release_driver(). Drop the duplicate assignment.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835_mmc: Remove vestigial threaded IRQ
With SDIO processing now managed by the MMC framework with a
workqueue, the bcm2835_mmc driver no longer needs a threaded
IRQ.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add missing dma_unmap_sg calls to free relevant swiotlb bounce buffers.
This prevents DMA leaks.
Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>
Limit max_req_size under arm64 (or any other platform that uses swiotlb) to prevent potential buffer overflow due to bouncing.
Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>
mmc: sdhci: Silence MMC warnings
When the MMC isn't plugged in, the driver will spam the console which is
pretty annoying when using NFS.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
mmc: sdhci-iproc: Fix vmmc regulators on iProc
The Linux support for controlling card power via regulators appears to
be contentious. I would argue that the default behaviour is contrary to
the SDHCI spec - turning off the power writes a reserved value to the
SD Bus Voltage Select field of the Power Control Register, which
seems to kill the Arasan/iProc controller - but fortunately there is a
hook in sdhci_ops to override the behaviour. Borrow the implementation
from sdhci_arasan_set_power.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: uninitialized_var is no more
Revert "mmc: sdhci-iproc: Fix vmmc regulators on iProc"
This reverts commit aed19399a0.
Commit 6c92ae1e45 ("mmc: sdhci: Introduce sdhci_set_power_and_bus_voltage()")
introduced a generic helper that does the same thing so use that instead in
the following commit.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
mmc: sdhci-iproc: Fix vmmc regulators (pre-bcm2711)
The Linux support for controlling card power via regulators appears to
be contentious. I would argue that the default behaviour is contrary to
the SDHCI spec - turning off the power writes a reserved value to the
SD Bus Voltage Select field of the Power Control Register, which
seems to kill the Arasan/iProc controller - but fortunately there is a
hook in sdhci_ops to override the behaviour.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2835-mmc: Honor return value of mmc_of_parse()
bcm2835_mmc_probe() ignores errors returned by mmc_of_parse() and in
particular ignores -EPROBE_DEFER, which may be returned if the power
sequencing driver configured in the devicetree is compiled as a module.
The user-visible result is that access to the SDIO device fails because
its power sequencing requirements have not been observed. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
bcm2835-mmc: Use phys addresses for slave DMA config
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
DMA: fix cyclic LITE length overflow bug
dmaengine: bcm2708: Remove chancnt affectations
Mirror bcm2835-dma.c commit 9eba5536a7:
chancnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: overwrite dreq only if it is not set
dreq is set when the DMA channel is fetched from Device Tree.
slave_id is set using dmaengine_slave_config().
Only overwrite dreq with slave_id if it is not set.
dreq/slave_id in the cyclic DMA case is not touched, because I don't
have hardware to test with.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: do device registration in the board file
Don't register the device in the driver. Do it in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Add Device Tree support to the non ARCH_BCM2835 case.
Use the same driver name regardless of architecture.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-dma entry
Add Device Tree entry for bcm2835-dma.
The entry doesn't contain any resources since they are handled
by the arch/arm/mach-bcm270x/dma.c driver.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine: Add debug options
BCM270x: Add memory and irq resources to dmaengine device and DT
Prepare for merging of the legacy DMA API arch driver dma.c
with bcm2708-dmaengine by adding memory and irq resources both
to platform file device and Device Tree node.
Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
Merge the legacy DMA API driver with bcm2708-dmaengine.
This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
driver is also needed).
Changes to the dma.c code:
- Use BIT() macro.
- Cutdown some comments to one line.
- Add mutex to vc_dmaman and use this, since the dev lock is locked
during probing of the engine part.
- Add global g_dmaman variable since drvdata is used by the engine part.
- Restructure for readability:
vc_dmaman_chan_alloc()
vc_dmaman_chan_free()
bcm_dma_chan_free()
- Restructure bcm_dma_chan_alloc() to simplify error handling.
- Use device irq resources instead of hardcoded bcm_dma_irqs table.
- Remove dev_dmaman_register() and code it directly.
- Remove dev_dmaman_deregister() and code it directly.
- Simplify bcm_dmaman_probe() using devm_* functions.
- Get dmachans from DT if available.
- Keep 'dma.dmachans' module argument name for backwards compatibility.
Make it available on ARCH_BCM2835 as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: set residue_granularity field
bcm2708-dmaengine supports residue reporting at burst level
but didn't report this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
bcm2708-dmaengine: Use more DMA channels (but not 12)
1) Only the bcm2708_fb drivers uses the legacy DMA API, and
it requires a BULK-capable channel, so all other types
(FAST, NORMAL and LITE) can be made available to the regular
DMA API.
2) DMA channels 11-14 share an interrupt. The driver can't
handle this, so don't use channels 12-14 (12 was used, probably
because it appears to have an interrupt, but in reality that
interrupt is for activity on ANY channel). This may explain
a lockup encountered when running out of DMA channels.
The combined effect of this patch is to leave 7 DMA channels
available + channel 0 for bcm2708_fb via the legacy API.
See: https://github.com/raspberrypi/linux/issues/1110https://github.com/raspberrypi/linux/issues/1108
dmaengine: bcm2708: Make legacy API available for bcm2835-dma
bcm2708_fb uses the legacy DMA API, so in order to start using
bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Change DT compatible string
Both bcm2835-dma and bcm2708-dmaengine have the same compatible string.
So change compatible to "brcm,bcm2708-dma".
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Remove driver but keep legacy API
Dropping non-DT support means we don't need this driver,
but we still need the legacy DMA API.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine - Fix arm64 portability/build issues
dma-bcm2708: Fix module compilation of CONFIG_DMA_BCM2708
bcm2708-dmaengine.c defines functions like bcm_dma_start which are
defined as well in dma-bcm2708.h as inline versions when
CONFIG_DMA_BCM2708 is not defined. This works fine when
CONFIG_DMA_BCM2708 is built in, but when it is selected as module build
fails with redefinition errors because in the build system when
CONFIG_DMA_BCM2708 is selected as module, the macro becomes
CONFIG_DMA_BCM2708_MODULE.
This patch makes the header use CONFIG_DMA_BCM2708_MODULE too when
available.
Fixes https://github.com/raspberrypi/linux/issues/2056
Signed-off-by: Andrei Gherzan <andrei@gherzan.com>
bcm2708-dmaengine: Use platform_get_irq
The platform driver framework no longer creates IRQ resources for
platform devices because they are expected to use platform_get_irq.
This causes the bcm2808_fb acceleration to fail.
Fix the problem by calling platform_get_irq as intended.
See: https://github.com/raspberrypi/linux/issues/5131
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2708_fb : Implement blanking support using the mailbox property interface
bcm2708_fb: Add pan and vsync controls
bcm2708_fb: DMA acceleration for fb_copyarea
Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
Also used Simon's dmaer_master module as a reference for tweaking DMA
settings for better performance.
For now busylooping only. IRQ support might be added later.
With non-overclocked Raspberry Pi, the performance is ~360 MB/s
for simple copy or ~260 MB/s for two-pass copy (used when dragging
windows to the right).
In the case of using DMA channel 0, the performance improves
to ~440 MB/s.
For comparison, VFP optimized CPU copy can only do ~114 MB/s in
the same conditions (hindered by reading uncached source buffer).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: report number of dma copies
Add a counter (exported via debugfs) reporting the
number of dma copies that the framebuffer driver
has done, in order to help evaluate different
optimization strategies.
Signed-off-by: Luke Diamand <luked@broadcom.com>
bcm2708_fb: use IRQ for DMA copies
The copyarea ioctl() uses DMA to speed things along. This
was busy-waiting for completion. This change supports using
an interrupt instead for larger transfers. For small
transfers, busy-waiting is still likely to be faster.
Signed-off-by: Luke Diamand <luke@diamand.org>
bcm2708: Make ioctl logging quieter
video: fbdev: bcm2708_fb: Don't panic on error
No need to panic the kernel if the video driver fails.
Just print a message and return an error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
fbdev: bcm2708_fb: Add ARCH_BCM2835 support
Add Device Tree support.
Pass the device to dma_alloc_coherent() in order to get the
correct bus address on ARCH_BCM2835.
Use the new DMA legacy API header file.
Including <mach/platform.h> is not necessary.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: Add bcm2708-fb device
Add bcm2708-fb to Device Tree and don't add the
platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Cleanup of bcm2708_fb file to kernel coding standards
Some minor change to function - remove a use of
in_atomic, plus replacing various debug messages
that manually specify the function name with
("%s",.__func__)
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
video: bcm2708_fb: Try allocating on the ARM and passing to VPU
Currently the VPU allocates the contiguous buffer for the
framebuffer.
Try an alternate path first where we use dma_alloc_coherent
and pass the buffer to the VPU. Should the VPU firmware not
support that path, then free the buffer and revert to the
old behaviour of using the VPU allocation.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Pulled in the multi frame buffer support from the Pi3 repo
fbdev: add FBIOCOPYAREA ioctl
Based on the patch authored by Ali Gholami Rudi at
https://lkml.org/lkml/2009/7/13/153
Provide an ioctl for userspace applications, but only if this operation
is hardware accelerated (otherwide it does not make any sense).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: Add ioctl for reading gpu memory through dma
video: bcm2708_fb: Add compat_ioctl support.
When using a 64 bit kernel with 32 bit userspace we need
compat ioctl handling for FBIODMACOPY as one of the
parameters is a pointer.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
video: fbdev: bcm2708_fb: Use common compat header
The definition of compat_ptr is now common for most platforms, but
requires the inclusion of <linux/compat.h>.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
video: bcm2708_fb: Disable FB if no displays found
If the firmware hasn't detected a display, the driver would assume
one display was available, but because it had failed to retrieve the
display size it would try to allocate a zero-sized buffer.
Avoid the allocation failure by bailing out early if no display is
found.
See: https://github.com/raspberrypi/linux/issues/3598
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2708_fb: Fix a build warning
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2708_fb: Explicitly initialise the IOMEM ops
Prior to [1], an fb_ops member of 0 was intepreted as a request for a
default value. This saves source code but requires special handling by
the framework, slowing down all accesses for no runtime benefit.
Use the new __FB_DEFAULT_ macros to explicitly select default handlers
in the bcm2708_fb driver. Also remove the pointless wrappers around
cfb_fillrect and cfb_imageblit - call them directly.
Link: https://forums.raspberrypi.com/viewtopic.php?p=2286016#p2286016
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1] 8813e86f6d ("fbdev: Remove default file-I/O implementations")
Signed-off-by: popcornmix <popcornmix@gmail.com>
usb: dwc: fix lockdep false positive
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
dwc_otg: Fix incorrect URB allocation error handling
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in
c4564d4a1a).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: Use kzalloc when suitable
dwc_otg: Pass struct device to dma_alloc*()
This makes it possible to get the bus address from Device Tree.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: fix summarize urb->actual_length for isochronous transfers
Kernel does not copy input data of ISO transfers to userspace
if actual_length is set only in ISO transfers and not summarized
in urb->actual_length. Fixesraspberrypi/linux#903
fiq_fsm: Use correct states when starting isoc OUT transfers
In fiq_fsm_start_next_periodic() if an isochronous OUT transfer
was selected, no regard was given as to whether this was a single-packet
transfer or a multi-packet staged transfer.
For single-packet transfers, this had the effect of repeatedly sending
OUT packets with bogus data and lengths.
Eventually if the channel was repeatedly enabled enough times, this
would lock up the OTG core and no further bus transfers would happen.
Set the FSM state up properly if we select a single-packet transfer.
Fixes https://github.com/raspberrypi/linux/issues/1842
dwc_otg: make nak_holdoff work as intended with empty queues
If URBs reading from non-periodic split endpoints were dequeued and
the last transfer from the endpoint was a NAK handshake, the resulting
qh->nak_frame value was stale which would result in unnecessarily long
polling intervals for the first subsequent transfer with a fresh URB.
Fixup qh->nak_frame in dwc_otg_hcd_urb_dequeue and also guard against
a case where a single URB is submitted to the endpoint, a NAK was
received on the transfer immediately prior to receiving data and the
device subsequently resubmits another URB past the qh->nak_frame interval.
Fixes https://github.com/raspberrypi/linux/issues/1709
dwc_otg: fix split transaction data toggle handling around dequeues
See https://github.com/raspberrypi/linux/issues/1709
Fix several issues regarding endpoint state when URBs are dequeued
- If the HCD is disconnected, flush FIQ-enabled channels properly
- Save the data toggle state for bulk endpoints if the last transfer
from an endpoint where URBs were dequeued returned a data packet
- Reset hc->start_pkt_count properly in assign_and_init_hc()
dwc_otg: fix several potential crash sources
On root port disconnect events, the host driver state is cleared and
in-progress host channels are forcibly stopped. This doesn't play
well with the FIQ running in the background, so:
- Guard the disconnect callback with both the host spinlock and FIQ
spinlock
- Move qtd dereference in dwc_otg_handle_hc_fsm() after the early-out
so we don't dereference a qtd that has gone away
- Turn catch-all BUG()s in dwc_otg_handle_hc_fsm() into warnings.
dwc_otg: delete hcd->channel_lock
The lock serves no purpose as it is only held while the HCD spinlock
is already being held.
dwc_otg: remove unnecessary dma-mode channel halts on disconnect interrupt
Host channels are already halted in kill_urbs_in_qh_list() with the
subsequent interrupt processing behaving as if the URB was dequeued
via HCD callback.
There's no need to clobber the host channel registers a second time
as this exposes races between the driver and host channel resulting
in hcd->free_hc_list becoming corrupted.
dwcotg: Allow to build without FIQ on ARM64
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: make periodic scheduling behave properly for FS buses
If the root port is in full-speed mode, transfer times at 12mbit/s
would be calculated but matched against high-speed quotas.
Reinitialise hcd->frame_usecs[i] on each port enable event so that
full-speed bandwidth can be tracked sensibly.
Also, don't bother using the FIQ for transfers when in full-speed
mode - at the slower bus speed, interrupt frequency is reduced by
an order of magnitude.
Related issue: https://github.com/raspberrypi/linux/issues/2020
dwc_otg: fiq_fsm: Make isochronous compatibility checks work properly
Get rid of the spammy printk and local pointer mangling.
Also, there is a nominal benefit for using fiq_fsm for isochronous
transfers in FS mode (~1.1k IRQs per second vs 2.1k IRQs per second)
so remove the root port speed check.
dwc_otg: add module parameter int_ep_interval_min
Add a module parameter (defaulting to ignored) that clamps the polling rate
of high-speed Interrupt endpoints to a minimum microframe interval.
The parameter is modifiable at runtime as it is used when activating new
endpoints (such as on device connect).
dwc_otg: fiq_fsm: Add non-periodic TT exclusivity constraints
Certain hub types do not discriminate between pipe direction (IN or OUT)
when considering non-periodic transfers. Therefore these hubs get confused
if multiple transfers are issued in different directions with the same
device address and endpoint number.
Constrain queuing non-periodic split transactions so they are performed
serially in such cases.
Related: https://github.com/raspberrypi/linux/issues/2024
dwc_otg: Fixup change to DRIVER_ATTR interface
dwc_otg: Fix compilation warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
USB_DWCOTG: Disable building dwc_otg as a module (#2265)
When dwc_otg is built as a module, build will fail with the following
error:
ERROR: "DWC_TASK_HI_SCHEDULE" [drivers/usb/host/dwc_otg/dwc_otg.ko] undefined!
scripts/Makefile.modpost:91: recipe for target '__modpost' failed
make[1]: *** [__modpost] Error 1
Makefile:1199: recipe for target 'modules' failed
make: *** [modules] Error 2
Even if the error is solved by including the missing
DWC_TASK_HI_SCHEDULE function, the kernel will panic when loading
dwc_otg.
As a workaround, simply prevent user from building dwc_otg as a module
as the current kernel does not support it.
See: https://github.com/raspberrypi/linux/issues/2258
Signed-off-by: Malik Olivier Boussejra <malik@boussejra.com>
dwc_otg: New timer API
dwc_otg: Fix removed ACCESS_ONCE->READ_ONCE
dwc_otg: don't unconditionally force host mode in dwc_otg_cil_init()
Add the ability to disable force_host_mode for those that want to use
dwc_otg in both device and host modes.
dwc_otg: Fix a regression when dequeueing isochronous transfers
In 282bed95 (dwc_otg: make nak_holdoff work as intended with empty queues)
the dequeue mechanism was changed to leave FIQ-enabled transfers to run
to completion - to avoid leaving hub TT buffers with stale packets lying
around.
This broke FIQ-accelerated isochronous transfers, as this then meant that
dozens of transfers were performed after the dequeue function returned.
Restore the state machine fence for isochronous transfers.
fiq_fsm: rewind DMA pointer for OUT transactions that fail (#2288)
See: https://github.com/raspberrypi/linux/issues/2140
dwc_otg: add smp_mb() to prevent driver state corruption on boot
Occasional crashes have been seen where the FIQ code dereferences
invalid/random pointers immediately after being set up, leading to
panic on boot.
The crash occurs as the FIQ code races against hcd_init_fiq() and
the hcd_init_fiq() code races against the outstanding memory stores
from dwc_otg_hcd_init(). Use explicit barriers after touching
driver state.
usb: dwc_otg: fix memory corruption in dwc_otg driver
[Upstream commit 51b1b64917]
The move from the staging tree to the main tree exposed a
longstanding memory corruption bug in the dwc2 driver. The
reordering of the driver initialization caused the dwc2 driver
to corrupt the initialization data of the sdhci driver on the
Raspberry Pi platform, which made the bug show up.
The error is in calling to_usb_device(hsotg->dev), since ->dev
is not a member of struct usb_device. The easiest fix is to
just remove the offending code, since it is not really needed.
Thanks to Stephen Warren for tracking down the cause of this.
Reported-by: Andre Heider <a.heider@gmail.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lukas: port from upstream dwc2 to out-of-tree dwc_otg driver]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
usb: dwb_otg: Fix unreachable switch statement warning
This warning appears with GCC 7.3.0 from toolchains.bootlin.com:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c: In function ‘fiq_fsm_update_hs_isoc’:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c:595:61: warning: statement will never be executed [-Wswitch-unreachable]
st->hctsiz_copy.b.xfersize = nrpackets * st->hcchar_copy.b.mps;
~~~~~~~~~~~~~~~~~^~~~
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
dwc_otg: fiq_fsm: fix incorrect DMA register offset calculation
Rationalise the offset and update all call sites.
Fixes https://github.com/raspberrypi/linux/issues/2408
dwc_otg: fix bug with port_addr assignment for single-TT hubs
See https://github.com/raspberrypi/linux/issues/2734
The "Hub Port" field in the split transaction packet was always set
to 1 for single-TT hubs. The majority of single-TT hub products
apparently ignore this field and broadcast to all downstream enabled
ports, which masked the issue. A subset of hub devices apparently
need the port number to be exact or split transactions will fail.
usb: dwc_otg: Clean up build warnings on 64bit kernels
No functional changes. Almost all are changes to logging lines.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
usb: dwc_otg: Use dma allocation for mphi dummy_send buffer
The FIQ driver used a kzalloc'ed buffer for dummy_send,
passing a kernel virtual address to the hardware block.
The buffer is only ever used for a dummy read, so it
should be harmless, but there is the chance that it will
cause exceptions.
Use a dma allocation so that we have a genuine bus address,
and read from that.
Free the allocation when done for good measure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
dwc_otg: only do_split when we actually need to do a split
The previous test would fail if the root port was in fullspeed mode
and there was a hub between the FS device and the root port. While
the transfer worked, the schedule mangling performed for high-speed
split transfers would break leading to an 8ms polling interval.
dwc_otg: fix locking around dequeueing and killing URBs
kill_urbs_in_qh_list() is practically only ever called with the fiq lock
already held, so don't spinlock twice in the case where we need to cancel
an isochronous transfer.
Also fix up a case where the global interrupt register could be read with
the fiq lock not held.
Fixes the deadlock seen in https://github.com/raspberrypi/linux/issues/2907
ARM64/DWC_OTG: Port dwc_otg driver to ARM64
In ARM64, the FIQ mechanism used by this driver is not current
implemented. As a workaround, reqular IRQ is used instead
of FIQ.
In a separate change, the IRQ-CPU mapping is round robined
on ARM64 to increase concurrency and allow multiple interrupts
to be serviced at a time. This reduces the need for FIQ.
Tests Run:
This mechanism is most likely to break when multiple USB devices
are attached at the same time. So the system was tested under
stress.
Devices:
1. USB Speakers playing back a FLAC audio through VLC
at 96KHz.(Higher then typically, but supported on my speakers).
2. sftp transferring large files through the buildin ethernet
connection which is connected through USB.
3. Keyboard and mouse attached and being used.
Although I do occasionally hear some glitches, the music seems to
play quite well.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
usb: dwc_otg: Clean up interrupt claiming code
The FIQ/IRQ interrupt number identification code is scattered through
the dwc_otg driver. Rationalise it, simplifying the code and solving
an existing issue.
See: https://github.com/raspberrypi/linux/issues/2612
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
dwc_otg: Choose appropriate IRQ handover strategy
2711 has no MPHI peripheral, but the ARM Control block can fake
interrupts. Use the size of the DTB "mphi" reg block to determine
which is required.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
usb: host: dwc_otg: fix compiling in separate directory
The dwc_otg Makefile does not respect the O=path argument correctly:
include paths in CFLAGS are given relatively to object path, not source
path. Compiling in a separate directory yields #include errors.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
dwc_otg: use align_buf for small IN control transfers (#3150)
The hardware will do a 4-byte write to memory on any IN packet received
that is between 1 and 3 bytes long. This tramples memory in the uvcvideo
driver, as it uses a sequence of 1- and 2-byte control transfers to
query the min/max/range/step of each individual camera control and
gives us buffers that are offsets into a struct.
Catch small control transfers in the data phase and use the align_buf
to bounce the correct number of bytes into the URB's buffer.
In general, short packets on non-control endpoints should be OK as URBs
should have enough buffer space for a wMaxPacket size transfer.
See: https://github.com/raspberrypi/linux/issues/3148
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: Declare DMA capability with HCD_DMA flag
Following [1], USB controllers have to declare DMA capabilities in
order for them to be used by adding the HCD_DMA flag to their hc_driver
struct.
[1] 7b81cb6bdd ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
dwc_otg: checking the urb->transfer_buffer too early (#3332)
After enable the HIGHMEM and VMSPLIT_3G, the dwc_otg driver doesn't
work well on Pi2/3 boards with 1G physical ram. Users experience
the failure when copying a file of 600M size to the USB stick. And
at the same time, the dmesg shows:
usb 1-1.1.2: reset high-speed USB device number 8 using dwc_otg
sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
blk_update_request: I/O error, dev sda, sector 3024048 op 0x1:(WRITE) flags 0x4000 phys_seg 15 prio class 0
When this happens, the sg_buf sent to the driver is located in the
highmem region, the usb_sg_init() in the core/message.c will leave
transfer_buffer to NULL if the sg_buf is in highmem, but in the
dwc_otg driver, it returns -EINVAL unconditionally if transfer_buffer
is NULL.
The driver can handle the situation of buffer to be NULL, if it is in
DMA mode, it will convert an address from transfer_dma.
But if the conversion fails or it is in the PIO mode, we should check
buffer and return -EINVAL if it is NULL.
BugLink: https://bugs.launchpad.net/bugs/1852510
Signed-off-by: Hui Wang <hui.wang@canonical.com>
dwc_otg: constrain endpoint max packet and transfer size on split IN
The hcd would unconditionally set the transfer length to the endpoint
packet size for non-isoc IN transfers. If the remaining buffer length
was less than the length of returned data, random memory would get
scribbled over, with bad effects if it crossed a page boundary.
Force a babble error if this happens by limiting the max transfer size
to the available buffer space. DMA will stop writing to memory on a
babble condition.
The hardware expects xfersize to be an integer multiple of maxpacket
size, so override hcchar.b.mps as well.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: fiq_fsm: pause when cancelling split transactions
Non-periodic splits will DMA to/from the driver-provided transfer_buffer,
which may be freed immediately after the dequeue call returns. Block until
we know the transfer is complete.
A similar delay is needed when cleaning up disconnects, as the FIQ could
have started a periodic transfer in the previous microframe to the one
that triggered a disconnect.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: fiq_fsm: add a barrier on entry into FIQ handler(s)
On BCM2835, there is no hardware guarantee that multiple outstanding
reads to different peripherals will complete in-order. The FIQ code
uses peripheral reads without barriers for performance, so in the case
where a read to a slow peripheral was issued immediately prior to FIQ
entry, the first peripheral read that the FIQ did could end up with
wrong read data returned.
Add dsb(sy) on entry so that all outstanding reads are retired.
The FIQ only issues reads to the dwc_otg core, so per-read barriers
in the handler itself are not required.
On BCM2836 and BCM2837 the barrier is not strictly required due to
differences in how the peripheral bus is implemented, but having
arch-specific handlers that introduce different latencies is risky.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: whitelist_table is now productlist_table
dwc_otg: initialise sched_frame for periodic QHs that were parked
If a periodic QH has no remaining QTDs, then it is removed from all
periodic schedules. When re-adding, initialise the sched_frame and
start_split_frame from the current value of the frame counter.
See https://bugs.launchpad.net/raspbian/+bug/1819560
and
https://github.com/raspberrypi/linux/issues/3883
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
dwc_otg: Minimise header and fix build warnings
Delete a large amount of unused declaration from "usb.h", some of which
were causing build warnings, and get the module building cleanly.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
dwc-otg: fix clang -Wignored-attributes warning
warning: attribute declaration must precede definition
dwc-otg: fix clang -Wsometimes-uninitialized warning
warning: variable 'retval' is used uninitialized whenever 'if' condition is false
dwc-otg: fix clang -Wpointer-bool-conversion warning
warning: address of array 'desc->wMaxPacketSize' will always evaluate to 'true'
The wMaxPacketSize field is actually a two element array which content should
be accessed via the UGETW macro.
dwc_otg: fix an undeclared variable
Replace an undeclared variable used by DWC_DEBUGPL with the real endpoint address. DWC_DEBUGPL does nothing with DEBUG undefined so it did not go wrong before.
Signed-off-by: Zixuan Wang <wangzixuan@sjtu.edu.cn>
dwc_otg: Update NetBSD usb.h header licence
NetBSD have changed their licensing requirements such that the 2-clause
licence is preferred. Update usb.h in the downstream dwc_otg code
accordingly.
See https://www.netbsd.org/about/redistribution.html for more
information.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
dwc_otg: pay attention to qh->interval when rescheduling periodic queues
A regression introduced in https://github.com/raspberrypi/linux/pull/3887
meant that if the newly scheduled transfer immediately returned data, and
the driver resubmitted a single URB after every transfer, then the effective
polling interval would end up being approx 1ms.
Use the larger of SCHEDULE_SLOP or the configured endpoint interval.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: dwc_otg: Fix fallthrough warnings
Signed-off-by: Alexander Winkowski <dereference23@outlook.com>
drivers: usb: dwc_otg: fix reference passing when checking bandwidth
The pointer (struct usb_host_endpoint *)->hcpriv should contain a
reference to dwc_otg_qh_t if the driver has already seen a URB submitted
to this endpoint.
It then checks whether the qh exists and is already in a schedule in
order to decide whether to allocate periodic bandwidth or not. Passing a
pointer to an offset inside of struct usb_host_endpoint instead of just
the pointer means it dereferences bogus addresses.
Rationalise (delete) a variable while we're at it.
See https://github.com/raspberrypi/linux/issues/5189
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: dwc_otg: stop GCC from patching FIQ functions
Configuring GCC to use task stack protector canaries means it will
insert calls to check functions in FIQ code. This is bad, as a) the
FIQ's stack is banked and b) the failure invokes __stack_chk_fail which
eventually tries to call printk(). Printing to the console inside the
FIQ is generally fatal.
Add CFLAGS to stop this happening in FIQ code.
Also catch one function where notrace wasn't specified.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
dwc_otg: Avoid the use of align_buf for short packets
Recent kernels (from 6.5) fail to boot on Pi0-3.
This has been tracked down to the call to:
ret = usb_get_std_status(hdev, USB_RECIP_DEVICE, 0, &hubstatus);
returning garbage in hubstatus (it gets the uninitialised contents of
a kmalloc buffer that is not overwritten as expected).
As we don't have strong evidence that this code path has ever worked,
and it is causing a clear problem currently, lets disable it to
allow wider use of newer kernels.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
drivers: dwc_otg: use C11 style variable array declarations
The kernel C standard changed in 5.18.
Remove a layer of indirection around the FIQ bounce buffers, be consistent
with pointers to FIQ bounce buffers, and remove open-coded 32-bit clamping
of DMA addresses.
Also remove a pointless fiq_state initialisation loop.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: dwc_otg: move FIQ locking functions to header file
Also declare as static inline, as they should be.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: dwc_otg: add ticket-based spinlock for ARM64
The ARM64 architecture uses qspinlock which has a fast and slow path.
This isn't ideal for all claimers of a lock operating in interrupt
context. Add a ticket-based lock similar to the armv6/7 implementation.
Based on an upstream patch that was abandoned in favour of qspinlock.
Link: https://patchwork.kernel.org/project/linux-arm-kernel/patch/1381330468-32625-2-git-send-email-will.deacon@arm.com/
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: dwc_otg: reduce loglevel for probe messages
Warning on normal behaviour isn't sensible and is spammy. Demote to info.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: dwc_otg: don't call disable_irq on the fake FIQ
The local spinlock protects the handlers from racing against each other
on separate cores, hard IRQs don't preempt each other, and
disabling/enabling the interrupt is more expensive than letting the fake
FIQ contend the spinlock.
So turn local_fiq_en/disable into no-ops.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Signed-off-by: popcornmix <popcornmix@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2709: Drop platform smp and timer init code
irq-bcm2836 handles this through these functions:
bcm2835_init_local_timer_frequency()
bcm2836_arm_irqchip_smp_init()
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm270x: Use watchdog for reboot/poweroff
The watchdog driver already has support for reboot/poweroff.
Make use of this and remove the code from the platform files.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
board_bcm2835: Remove coherent dma pool increase - API has gone
Under some circumstances on BCM283x processors data loss can be
observed - a single byte missing from the TX output stream. These bytes
are always the last byte of a batch of 8 written from pl011_tx_chars
when from_irq is true, meaning that the FIFO full flag is not checked
before writing.
The transmit optimisation relies on the FIFO being half-empty when the
TX interrupt is raised. Instrumenting the driver further showed that
the failure case correlated with the TX FIFO full flag being set at the
point where the last byte was written to the data register, which
explains the data loss but not how the FIFO appeared to be prematurely
full. A possible explanation is that a FIFO write was in flight at the
time the interrupt was raised, but as yet there is no hypothesis as to
how this might occur.
In the absence of a clear understanding of the failure mechanism, avoid
the problem by checking the FIFO levels before writing the last byte of
the group, which will have minimal performance impact.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The BCM2835 PL011 implementation seems to have a bug that can lead to a
transmission lockup if CTS changes frequently. A workaround was added to
the driver with a vendor-specific flag to enable it, but this flag is
currently not set for ARM implementations.
Add a "cts-event-workaround" property to Pi DTBs and use the presence
of that property to force the flag to be enabled in the driver.
See: https://github.com/raspberrypi/linux/issues/1280
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The pl011 register accessor functions use the _relaxed versions of the
standard readl() and writel() functions, meaning that there are no
automatic memory barriers. When polling a FIFO status register to check
for fullness, it is necessary to ensure that any outstanding writes have
completed; otherwise the flags are effectively stale, making it possible
that the next write is to a full FIFO.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The syscon node defines a register range that duplicates that used by
the local_intc node on bcm2836/7. Since irq-bcm2835 and irq-bcm2836 are
built in and always present together (both drivers are enabled by
CONFIG_ARCH_BCM2835), it is possible to replace the syscon usage with a
global variable that simplifies the code. Doing so does lose the
locking provided by regmap, but as only one side is using the regmap
interface (irq-bcm2835 uses readl and write) there is no loss of
atomicity.
See: https://github.com/raspberrypi/firmware/issues/926
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
This adds a debug module parameter to aid in debugging transfer issues
by printing info to the kernel log. When enabled, status values are
collected in the interrupt routine and msg info in
bcm2835_i2c_start_transfer(). This is done in a way that tries to avoid
affecting timing. Having printk in the isr can mask issues.
debug values (additive):
1: Print info on error
2: Print info on all transfers
3: Print messages before transfer is started
The value can be changed at runtime:
/sys/module/i2c_bcm2835/parameters/debug
Example output, debug=3:
[ 747.114448] bcm2835_i2c_xfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.114463] bcm2835_i2c_xfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117809] start_transfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.117825] isr: remain=2, status=0x30000055 : TA TXW TXD TXE [i2c1]
[ 747.117839] start_transfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117849] isr: remain=32, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117861] isr: remain=20, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117870] isr: remain=8, status=0x32 : DONE TXD RXD [i2c1]
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Christopher Alexander Tobias Schulze - May 2, 2015, 11:57 a.m.
This patch fixes a problem with VFP state save and restore related
to exception handling (panic with message "BUG: unsupported FP
instruction in kernel mode") present on VFP11 floating point units
(as used with ARM1176JZF-S CPUs, e.g. on first generation Raspberry
Pi boards). This patch was developed and discussed on
https://github.com/raspberrypi/linux/issues/859
A precondition to see the crashes is that floating point exception
traps are enabled. In this case, the VFP11 might determine that a FPU
operation needs to trap at a point in time when it is not possible to
signal this to the ARM11 core any more. The VFP11 will then set the
FPEXC.EX bit and store the trapped opcode in FPINST. (In some cases,
a second opcode might have been accepted by the VFP11 before the
exception was detected and could be reported to the ARM11 - in this
case, the VFP11 also sets FPEXC.FP2V and stores the second opcode in
FPINST2.)
If FPEXC.EX is set, the VFP11 will "bounce" the next FPU opcode issued
by the ARM11 CPU, which will be seen by the ARM11 as an undefined opcode
trap. The VFP support code examines the FPEXC.EX and FPEXC.FP2V bits
to decide what actions to take, i.e., whether to emulate the opcodes
found in FPINST and FPINST2, and whether to retry the bounced instruction.
If a user space application has left the VFP11 in this "pending trap"
state, the next FPU opcode issued to the VFP11 might actually be the
VSTMIA operation vfp_save_state() uses to store the FPU registers
to memory (in our test cases, when building the signal stack frame).
In this case, the kernel crashes as described above.
This patch fixes the problem by making sure that vfp_save_state() is
always entered with FPEXC.EX cleared. (The current value of FPEXC has
already been saved, so this does not corrupt the context. Clearing
FPEXC.EX has no effects on FPINST or FPINST2. Also note that many
callers already modify FPEXC by setting FPEXC.EN before invoking
vfp_save_state().)
This patch also addresses a second problem related to FPEXC.EX: After
returning from signal handling, the kernel reloads the VFP context
from the user mode stack. However, the current code explicitly clears
both FPEXC.EX and FPEXC.FP2V during reload. As VFP11 requires these
bits to be preserved, this patch disables clearing them for VFP
implementations belonging to architecture 1. There should be no
negative side effects: the user can set both bits by executing FPU
opcodes anyway, and while user code may now place arbitrary values
into FPINST and FPINST2 (e.g., non-VFP ARM opcodes) the VFP support
code knows which instructions can be emulated, and rejects other
opcodes with "unhandled bounce" messages, so there should be no
security impact from allowing reloading FPEXC.EX and FPEXC.FP2V.
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
reboot: Use power off rather than busy spinning when halt is requested
Busy spinning after halt is dumb
We've previously applied this patch to arch/arm
but it is currenltly missing in arch/arm64
Pi4 after "sudo halt" uses 520mA
Pi4 after "sudo shutdown now" uses 310mA
Make them both use the lower powered option
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
The Raspberry Pi firmware looks at the RSTS register to know which
partition to boot from. The reboot syscall command
LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument.
Add support for passing in a partition number 0..63 to boot from.
Partition 63 is a special partiton indicating halt.
If the partition doesn't exist, the firmware falls back to partition 0.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-dma: Add support for per-channel flags
Add the ability to interpret the high bits of the dreq specifier as
flags to be included in the DMA_CS register. The motivation for this
change is the ability to set the DISDEBUG flag for SD card transfers
to avoid corruption when using the VPU debugger.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-dma: Add proper 40-bit DMA support
BCM2711 has 4 DMA channels with a 40-bit address range, allowing them
to access the full 4GB of memory on a Pi 4.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-dma: Derive slave DMA addresses correctly
Slave addresses for DMA are meant to be supplied as physical addresses
(contrary to what struct snd_dmaengine_dai_dma_data does). It is up to
the DMA controller driver to perform the translation based on its own
view of the world, as described in Device Tree.
Now that the Pi Device Trees have the correct peripheral mappings,
replace the hacky address munging with phys_to_dma().
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2835-dma: Add NO_WAIT_RESP flag
Use bit 27 of the dreq value (the second cell of the DT DMA descriptor)
to request that the WAIT_RESP bit is not set.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2835-dma: Advertise the full DMA range
Unless the DMA mask is set wider than 32 bits, DMA mapping will use a
bounce buffer.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2835-dma: only reserve channel 0 if legacy dma driver is enabled
If CONFIG_DMA_BCM2708 isn't enabled there's no need to mask out
one of the already scarce DMA channels.
Signed-off-by: Matthias Reichl <hias@horus.com>
bcm2835-dma: Avoid losing CS flags after interrupt
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
bcm2835-dma: Add bcm2835-dma: Add DMA_WIDE_SOURCE and DMA_WIDE_DEST flags
Use (reserved) bits 24 and 25 of the dreq value
(the second cell of the DT DMA descriptor) to request
that wide source reads or wide dest writes are required
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
dmaengine: bcm2835: Fix position reporting for 40 bits channels
For 40 bits channels, the position is reported by reading the upper byte
in the SRCI/DESTI registers. However the driver adds that upper byte
with an 8-bits left shift, while it should be 32.
Fixes: 9a52a99183 ("bcm2835-dma: Add proper 40-bit DMA support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
dmaengine: bcm2835: Use to_bcm2711_cbaddr where relevant
bcm2711_dma40_memcpy has some code strictly equivalent to the
to_bcm2711_cbaddr() function. Let's use it instead.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
dmaengine: bcm2835: Fix descriptors usage for 40-bits channels
The bcm2835_dma_create_cb_chain() function is in charge of building up
the descriptors chain for a given transfer.
It was initially supporting only the BCM2835-style DMA controller, and
was later expanded to support controllers with 40-bits channels that use
a different descriptor layout.
However, some part of the function only use the old style descriptor,
even when building a chain of new-style descriptors, resulting in weird
bugs.
Fixes: 9a52a99183 ("bcm2835-dma: Add proper 40-bit DMA support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
bcm2835-dma: Fix WAIT_RESP on memcpy
It goes in info not extra
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
bcm2835-dma: Fix dma_abort for 40-bit channels
It wasn't aborting the transfer and caused stop/start
of hdmi audio dma to be unreliable.
New sequence approved by Broadcom.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
bcm2835-dma: Fix dma_abort for non-40bit channels
The sequence we were doing was not safe.
Clearing CS meant BCM2835_DMA_WAIT_FOR_WRITES was cleared
and so polling BCM2835_DMA_WAITING_FOR_WRITES has no benefit
Broadcom have provided a recommended sequence to abort
a dma lite channel, so switch to that.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
bcm2835-dma: Support dma flags for multi-beat burst
Add a control bit to enable a multi-beat burst on a DMA.
This improves DMA performance and is required for HDMI audio.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
bcm2835-dma: Need to keep PROT bits set in CS on 40bit controller
Resetting them to zero puts DMA channel into secure mode
which makes further accesses impossible
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
dmaengine: bcm2835: Delete vestigial code
The dedicated dma40 memcpy code is no longer used, and without a
prototype the kernel build fails. Delete it.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
dmaengine: bcm2835: Use dma_map_resource
The commit titled "bcm2835-dma: Derive slave DMA addresses correctly"
(now squashed into DMA roll-up) moved the responsibility for calculating
DMA addresses to the DMA driver. Unfortunately it committed the sin of
using phys_to_dma directly rather than using the approved API, i.e.
dma_map_resource.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
An alternative strategy would be to use "rpi,spidev" instead, but that
would require many Raspberry Pi Device Tree changes.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: popcornmix <popcornmix@gmail.com>
SQUASH: smsc95xx: Use dev_mod_addr to set MAC addr
Since adeef3e321 ("net: constify netdev->dev_addr") it has been
illegal to write to the dev_addr MAC address field. Later commits
have added explicit checks that it hasn't been modified by nefarious
means. The dev_addr_mod helper function is the accepted way to change
the dev_addr field, so use it.
Squash with 96c1def63ee1 ("Allow mac address to be set in smsc95xx").
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
DSI0 can take the clock from either PLLA or PLLD. PLLA is
the default muxing, but PLLD is considered the more stable.
Switch to using PLLD.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This is controlled by firmware, see clk-raspberrypi.c
Signed-off-by: popcornmix <popcornmix@gmail.com>
clk-bcm2835: Remove VEC clock support
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
This falls under the same "we can reprogram glitch-free as long as we
pause generation" rule as updating the div/frac fields. This can be
used for runtime reclocking of V3D to manage power leakage.
Signed-off-by: Eric Anholt <eric@anholt.net>
The VPU is responsible for managing the core clock, usually under
direction from the bcm2835-cpufreq driver but not via the clk-bcm2835
driver. Since the core frequency can change without warning, it is
safer to report the maximum clock rate to users of the core clock -
I2C, SPI and the mini UART - to err on the safe side when calculating
clock divisors.
If the DT node for the clock driver includes a reference to the
firmware node, use the firmware API to query the maximum core clock
instead of reading the divider registers.
Prior to this patch, a "100KHz" I2C bus was sometimes clocked at about
160KHz. In particular, switching to the 4.9 kernel was likely to break
SenseHAT usage on a Pi3.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
clk: bcm2835: Pass DT node to rpi_firmware_get
The fw_node pointer has already been retrieved, and using it allows
us to remove a downstream patch to the firmware driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
The claim-clocks property can be used to prevent PLLs and dividers
from being marked as critical. It contains a vector of clock IDs,
as defined by dt-bindings/clock/bcm2835.h.
Use this mechanism to claim PLLD_DSI0, PLLD_DSI1, PLLH_AUX and
PLLH_PIX for the vc4_kms_v3d driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The VPU configures and relies on several PLLs and dividers. Mark all
enabled dividers and their PLLs as CRITICAL to prevent the kernel from
switching them off.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
so that special/critical clocks can get enabled early on in the
boot process avoiding the risk of disabling a clock, pll_divider
or pll when a claiming driver fails to install propperly - maybe it needs to defer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
clk: clk-bcm2835: Use %zd when printing size_t
The debug text for how many clocks have been registered
uses "%d" with a size_t. Correct it to "%zd".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Initialise rpi-firmware before clk-bcm2835
The IMA (Integrity Measurement Architecture) looks for a TPM (Trusted
Platform Module) having been registered when it initialises; otherwise
it assumes there is no TPM. It has been observed on BCM2835 that IMA
is initialised before TPM, and that initialising the BCM2835 clock
driver before the firmware driver has the effect of reversing this
order.
Change the firmware driver to initialise at core_initcall, delaying the
BCM2835 clock driver to postcore_initcall.
See: https://github.com/raspberrypi/linux/issues/3291https://github.com/raspberrypi/linux/pull/3297
Signed-off-by: Luke Hinds <lhinds@redhat.com>
Co-authored-by: Phil Elwell <phil@raspberrypi.org>
clk-bcm2835: use subsys_initcall for the clock driver when IMA is enabled
Co-authored-by: Davide Scovotto <scovottodavide@gmail.com>
Co-developed-by: Davide Scovotto <scovottodavide@gmail.com>
Signed-off-by: Davide Scovotto <scovottodavide@gmail.com>
Signed-off-by: Alberto Solavagione <albertosolavagione30@gmail.com>
Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
Mainline dts files are based on these files:
bcm2835-rpi.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
Current downstream are based on these:
bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi
bcm2708_common.dtsi
This patch introduces this dependency:
bcm2708.dtsi bcm2709.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
And:
bcm2710.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm283x.dtsi
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
BCM270X: Drop position requirement for CMA in VC4 overlay.
No longer necessary since 2aefcd5761,
and will probably let peeople that want to choose a larger CMA
allocation (particularly on pi0/1).
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM270X_DT: RPi Device Tree tidy
Use the upstream sdhost node, add thermal-zones, and factor out some
common elements.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
kbuild: Silence unhelpful DTC warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: DT build rules no longer arch-specific
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
kbuild: Silence unavoidable dtc overlay warnings
Much effort has been put into finding ways to avoid warnings from dtc
about overlays, usually to do with the presence of #address-cells and
size-cells, but not exclusively so. Since the issues being warned about
are harmless, suppress the warnings to declutter the build output and
to avoid alarming users.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
overlays: Suppress another dtc warning
I'm sure the dtc warnings mean well, but overlays don't have enough
context for the checkers to give meaningful results.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
overlays: Use dtbs-list for overlay installation
Update the overlay build rules to use the dtbs-list mechanism. Also
include the README, and don't set the executable bits.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
overlays: i2c-sensor: Add tmp117 support
Add support for the TMP117 temperature sensor to the i2c-sensor
overlay.
See: https://github.com/raspberrypi/linux/issues/7077
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Margins may be implemented by scaling the planes, but as there
is no way of intercepting the set_property for a standard property,
and all planes are checked in drm_atomic_check_only before the
connectors, there's now way to add the planes into the state
from the driver.
If the margin properties change, add all corresponding planes to
the state.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The stuff never really worked, and leads to lots of fun because it
out-of-order frees atomic states. Which upsets KASAN, among other
things.
For async updates we now have a more solid solution with the
->atomic_async_check and ->atomic_async_commit hooks. Support for that
for msm and vc4 landed. nouveau and i915 have their own commit
routines, doing something similar.
For everyone else it's probably better to remove the use-after-free
bug, and encourage folks to use the async support instead. The
affected drivers which register a legacy cursor plane and don't either
use the new async stuff or their own commit routine are: amdgpu,
atmel, mediatek, qxl, rockchip, sti, sun4i, tegra, virtio, and vmwgfx.
Inspired by an amdgpu bug report.
v2: Drop RFC, I think with amdgpu converted over to use
atomic_async_check/commit done in
commit 674e78acae
Author: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Date: Wed Dec 5 14:59:07 2018 -0500
drm/amd/display: Add fast path for cursor plane updates
we don't have any driver anymore where we have userspace expecting
solid legacy cursor support _and_ they are using the atomic helpers in
their fully glory. So we can retire this.
v3: Paper over msm and i915 regression. The complete_all is the only
thing missing afaict.
v4: Rebased on recent kernel, added extra link for vc4 bug.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199425
Link: https://lore.kernel.org/all/20220221134155.125447-9-maxime@cerno.tech/
Cc: mikita.lipski@amd.com
Cc: Michel Dänzer <michel@daenzer.net>
Cc: harry.wentland@amd.com
Cc: Rob Clark <robdclark@gmail.com>
Cc: "Kazlauskas, Nicholas" <nicholas.kazlauskas@amd.com>
Tested-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
mipi_dsi_attach can fail due to resources not being available
yet, therefore do not log error messages should they occur.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The MIPI_DSI_MODE_* flags have fairly terse descriptions and no reference
to the DSI specification as to their exact meaning. Usage has therefore
been rather fluid.
Extend the descriptions and provide references to the part of the
MIPI DSI specification regarding what they mean.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm_crtc_legacy_gamma_set updates the gamma_lut blob unconditionally,
which leads to unnecessary reprogramming of hardware.
Check whether the blob contents has actually changed before
signalling that it has been updated.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
CI builds are done with debug info disabled, but this removes some
members from struct module. This causes builds to fail if there is an
ABI reference for the current ABI.
Define these members unconditionally, so that there is no ABI change.
When symbols from overlays are added to the live tree their paths must
be rebased. The translated symbol is normally the result of joining
the fragment-relative path (with a leading "/") to the target path
(either copied directly from the "target-path" property or resolved
from the phandle). This translation fails when the target is the root
node (a common case for Raspberry Pi overlays) because the resulting
path starts with a double slash. For example, if target-path is "/" and
the fragment adds a node called "newnode", the label associated with
that node will be assigned the path "//newnode", which can't be found
in the tree.
Fix the failure case by explicitly replacing a target path of "/" with
an empty string.
Fixes: d1651b03c2 ("of: overlay: add overlay symbols to live device tree")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Use GitHubs issue form for bug reports.
- modern look
- user don't need to mess with given markdown parts while filling the issue template
Setup config.yml for general questions and problems with the Raspbian distribution packages.
Update issue templates (#2736)
Adding Pi 5 as a device to bug_report.yml
Update the Issue template
* Update config.yml - Raspbian -> Raspberry Pi OS
* Update config.yml
* .org to .com
* Update forum URL
Add Pi 500 and CM5 as a device to bug_report.yml
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Suggest 'raspinfo | pastebinit' in bug_report.yml
Output of raspinfo is now over 65,000 characters, which is more than
GitHub allows in a single form field!
Also adds Pi 500+ and CM0 to the list of models.
This is a copy of README with the tags added.
You can not delete the file README as then checkpatch complains
you aren't in a kernel tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
README: Show rpi-6.5.y build status
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
README: show rpi-6.6.y build status
Replace rpi-6.5.y with rpi-6.6.y in the build status list.
README: show rpi-6.12.y build status
Remove rpi-5.15.y build status since it doesn't appear to be built anymore, and add rpi-6.12.y build status.
This is currently running on defaults, so the --strict desired
for media drivers and similar won't be observed. That may be
possible to add later.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
.github: Add Github Workflow for KUnit
Now that we have some KUnit coverage, let's add a github actions file to
run them on each push or pull request.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
.github/workflows: Add dtoverlaycheck workflow
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
.github/workflows: Create workflow to CI kernel builds
Builds the bcmrpi, bcm2709, bcm2711, and bcm2835 32 bit kernels,
and defconfig and bcm2711 64bit kernels, saving the artifacts for
7 days.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
.github: Skip broken Generic DRM/KMS Unit Tests
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
.github/workflows: Set warnings-as-errors for builds
To avoid code with build warnings being introduced into the tree, force
CONFIG_WERROR=y in the build workflow.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
.github/workflows: Correct kernel builds artifacts
Modify the kernel build workflow to create artifacts with the correct
names and structure, both as an example of what we expect and in case
anyone wants to use the output.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
.github/workflows: Switch to a matrix build
Remove the per-build duplication by putting build parameters in a
matrix.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
.github/workflows: Retain artifacts for 90 days
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
.github/workflows: Add a bcm2712 build configuration
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Update kernel-build.yml to use node.js 20
Upgrade the actions to v4 to get rid of the warning about migrating from node.js 16.
Update kunit.yml to use node.js 20
Bump actions/checkout to v4.
Update dtoverlaycheck.yml to node.js 20
.github/workflows: More jobs for kernel builds
Using the "cores * 1.5" heuristic, configure the kernel builds for the
4-core GitHub-hosted runners.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
workflows: Add arm64 bcm2711_rt build
Add a Github CI workflow bcm2711_rt_defconfig
Signed-off-by: Tim Gover <tim.gover@raspberrypi.com>
workflows: Remove the ARCH=arm bcm2711 build
As we will be moving Pi 4 support to kernel8.img only and dropping
kernel7l.img, the ARCH=arm bcm2711 defconfig has been deleted.
Remove the corresponding autobuild.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
workflows: Use bcm2709_defconfig for dtoverlaycheck
Now that ARCH=arm bcm2711_defconfig has been deleted, update
dtoverlaycheck to use bcm2709_defconfig.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
kunit: Use ubuntu-22.04 for arm64
There's a bug in the version of qemu used by Ubuntu 24.04 that kills
the arm64 KUnit test. Revert to Ubuntu 22.04 just for that test,
until ubuntu-latest updates to qemu 9.2.0+.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1236310
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
workflows: Switch to overlaycheck's thorough mode
Now that the current trees are passing the thorough/try-all mode of
overlaycheck (mainly by excluding trying to apply the vl805 overlay
on a CM4S), use it in the build checks.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
workflows: Ignore checkpatch UNKNOWN_COMMIT_ID
As we do a shallow clone of the repo, Fixes: tags
generally don't have the matching commit available
to lookup, and checkpatch logs it.
Ignore this error.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
workflows: dtoverlaycheck: Update the dependencies
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
workflows: Increase timeout for toolchain install
5 minutes seems to be failing on a regular basis, so
increase it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
workflows: Increase DT tools installation timeout
Increase the timeout for the toolchain installation in the
dtoverlaycheck workflow, to match that for the kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
workflows: Use native arm64 runners
Use native arm64 runners to speed up build process. Cross compile is
still used for arm targets, but also benefit from the arm64 runner
architecture. Overall build time will be reduced by 25 to 30 minutes by
this.
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Pull clk fixes from Stephen Boyd:
"Fixes for the Allwinner A523 clk driver:
- Lower the minimum rate for the A523 audio PLL to support
frequencies required by audio devices
- Mark a couple clks critical on A523 so that Linux doesn't turn them
off when they're used by other code like TF-A"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: sun55i-a523-ccu: Lower audio0 pll minimum rate
clk: sunxi-ng: sun55i-a523-r-ccu: Mark bus-r-dma as critical
clk: sunxi-ng: Mark A523 bus-r-cpucfg clock as critical
Pull timer fixes from Ingo Molnar:
- Fix a race in timer->function clearing in timer_shutdown_sync()
- Fix a timekeeper sysfs-setup resource leak in error paths
- Fix the NOHZ report_idle_softirq() syslog rate-limiting
logic to have no side effects on the return value
* tag 'timers-urgent-2025-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Fix NULL function pointer race in timer_shutdown_sync()
timekeeping: Fix resource leak in tk_aux_sysfs_init() error paths
tick/sched: Fix bogus condition in report_idle_softirq()
There is a race condition between timer_shutdown_sync() and timer
expiration that can lead to hitting a WARN_ON in expire_timers().
The issue occurs when timer_shutdown_sync() clears the timer function
to NULL while the timer is still running on another CPU. The race
scenario looks like this:
CPU0 CPU1
<SOFTIRQ>
lock_timer_base()
expire_timers()
base->running_timer = timer;
unlock_timer_base()
[call_timer_fn enter]
mod_timer()
...
timer_shutdown_sync()
lock_timer_base()
// For now, will not detach the timer but only clear its function to NULL
if (base->running_timer != timer)
ret = detach_if_pending(timer, base, true);
if (shutdown)
timer->function = NULL;
unlock_timer_base()
[call_timer_fn exit]
lock_timer_base()
base->running_timer = NULL;
unlock_timer_base()
...
// Now timer is pending while its function set to NULL.
// next timer trigger
<SOFTIRQ>
expire_timers()
WARN_ON_ONCE(!fn) // hit
...
lock_timer_base()
// Now timer will detach
if (base->running_timer != timer)
ret = detach_if_pending(timer, base, true);
if (shutdown)
timer->function = NULL;
unlock_timer_base()
The problem is that timer_shutdown_sync() clears the timer function
regardless of whether the timer is currently running. This can leave a
pending timer with a NULL function pointer, which triggers the
WARN_ON_ONCE(!fn) check in expire_timers().
Fix this by only clearing the timer function when actually detaching the
timer. If the timer is running, leave the function pointer intact, which is
safe because the timer will be properly detached when it finishes running.
Fixes: 0cc04e8045 ("timers: Add shutdown mechanism to the internal functions")
Signed-off-by: Yipeng Zou <zouyipeng@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251122093942.301559-1-zouyipeng@huawei.com
Pull MIPS fixes from Thomas Bogendoerfer:
- Fix CPU type in DT for econet
- Fix for Malta PCI MMIO breakage for SOC-it
- Fix TLB shutdown caused by iniital uniquification
- Fix random seg faults due to missed vdso storage requirement
* tag 'mips-fixes_6.18_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: kernel: Fix random segmentation faults
MIPS: mm: Prevent a TLB shutdown on initial uniquification
mips: dts: econet: fix EN751221 core type
MIPS: Malta: Fix !EVA SOC-it PCI MMIO
Pull crypto library fix from Eric Biggers:
"Fix another KMSAN warning that made it in while KMSAN wasn't working
reliably"
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: tests: Fix KMSAN warning in test_sha256_finup_2x()
Pull xfs fix from Carlos Maiolino:
"A single out-of-bounds fix, nothing special"
* tag 'xfs-fixes-6.18-rc7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix out of bounds memory read error in symlink repair
Pull SCSI fixes from James Bottomley:
"One target driver fix and one scsi-generic one. The latter is 10 lines
because the problem lock has to be dropped and re-taken around the
call causing the sleep in atomic"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sg: Do not sleep in atomic context
scsi: target: tcm_loop: Fix segfault in tcm_loop_tpg_address_show()
Pull input fixes from Dmitry Torokhov:
- INPUT_PROP_HAPTIC_TOUCHPAD definition added early in 6.18 cycle has
been renamed to INPUT_PROP_PRESSUREPAD to better reflect the kind of
devices it is supposed to be set for
- a new ID for a touchscreen found in Ayaneo Flip DS in Goodix driver
- Goodix driver no longer tries to set reset pin as "input" as it
causes issues when there is no pull up resistor installed on the
board
- fixes for cros_ec_keyb, imx_sc_key, and pegasus-notetaker drivers to
deal with potential out-of-bounds access and memory corruption issues
* tag 'input-for-v6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: rename INPUT_PROP_HAPTIC_TOUCHPAD to INPUT_PROP_PRESSUREPAD
Input: cros_ec_keyb - fix an invalid memory access
Input: imx_sc_key - fix memory corruption on unload
Input: pegasus-notetaker - fix potential out-of-bounds access
Input: goodix - remove setting of RST pin to input
Input: goodix - add support for ACPI ID GDIX1003
Pull RISC-V fixes from Paul Walmsley:
- Correct the MIPS RISC-V/JEDEC vendor ID
- Fix the system shutdown behavior in the legacy case where
CONFIG_RISCV_SBI_V01 is set, but the firmware implementation
doesn't support the older v0.1 system shutdown method
- Align some tools/ macro definitions with the corresponding
kernel headers
* tag 'riscv-for-linus-6.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
tools: riscv: Fixed misalignment of CSR related definitions
riscv: sbi: Prefer SRST shutdown over legacy
riscv: Update MIPS vendor id to 0x127
Pull selinux fixes from Paul Moore:
"Three SELinux patches for v6.18 to fix issues around accessing the
per-task decision cache that we introduced in v6.16 to help reduce
SELinux overhead on path walks. The problem was that despite the cache
being located in the SELinux "task_security_struct", the parent struct
wasn't actually tied to the task, it was tied to a cred.
Historically SELinux did locate the task_security_struct in the
task_struct's security blob, but it was later relocated to the cred
struct when the cred work happened, as it made the most sense at the
time.
Unfortunately we never did the task_security_struct to
cred_security_struct rename work (avoid code churn maybe? who knows)
because it didn't really matter at the time. However, it suddenly
became a problem when we added a per-task cache to a per-cred object
and didn't notice because of the old, no-longer-correct struct naming.
Thanks to KCSAN for flagging this, as the silly humans running things
forgot that the task_security_struct was a big lie.
This contains three patches, only one of which actually fixes the
problem described above and moves the SELinux decision cache from the
per-cred struct to a newly (re)created per-task struct.
The other two patches, which form the bulk of the diffstat, take care
of the associated renaming tasks so we can hopefully avoid making the
same stupid mistake in the future.
For the record, I did contemplate sending just a fix for the cache,
leaving the renaming patches for the upcoming merge window, but the
type/variable naming ended up being pretty awful and would have made
v6.18 an outlier stuck between the "old" names and the "new" names in
v6.19. The renaming patches are also fairly mechanical/trivial and
shouldn't pose much risk despite their size.
TLDR; naming things may be hard, but if you mess it up bad things
happen"
* tag 'selinux-pr-20251121' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: rename the cred_security_struct variables to "crsec"
selinux: move avdcache to per-task security struct
selinux: rename task_security_struct to cred_security_struct
Pull LoongArch fixes from Huacai Chen:
"Use UAPI types in ptrace UAPI header to fix nolibc ptrace.
Fix CPU name display, NUMA node parsing, kexec/kdump, PCI init and BPF
trampoline"
* tag 'loongarch-fixes-6.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: BPF: Disable trampoline for kernel module function trace
LoongArch: Don't panic if no valid cache info for PCI
LoongArch: Mask all interrupts during kexec/kdump
LoongArch: Fix NUMA node parsing with numa_memblks
LoongArch: Consolidate CPU names in /proc/cpuinfo
LoongArch: Use UAPI types in ptrace UAPI header
Pull smb client fixes from Steve French:
- Fix potential memory leak in mount
- Add some missing read tracepoints
- Fix locking issue with directory leases
* tag 'v6.18-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Add the smb3_read_* tracepoints to SMB1
cifs: fix memory leak in smb3_fs_context_parse_param error path
smb: client: introduce close_cached_dir_locked()
Pull io_uring fix from Jens Axboe:
"Just a single fix for a mixup of arguments for the skb_queue_splice()
call, in the io_uring timestamp retrieval code"
* tag 'io_uring-6.18-20251120' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
io_uring/cmd_net: fix wrong argument types for skb_queue_splice()
Pull ata fixes from Niklas Cassel:
- Add a missing refcount decrement in ata_scsi_dev_rescan() when
the device or its queue is not running.
In the case where the device is running, the recount is already
decremented properly (Yihang Li)
- Generate the proper sense code for a Security locked device.
There was a regression caused by a recent change of how sense
data is generated for commands that did not provide any sense
data. This broke system suspend for Security locked devices.
Generate the sense data that the SCSI disk driver expects for a
Security locked device so that system suspend works again (me)
- Set capacity to zero for a Security locked device.
All I/O commands will be aborted by a Security locked device.
Thus, the block layer disk partition scanning will result in
a bunch of, for the user, confusing I/O errors in dmesg during
boot.
Since a Security locked device is unusable anyway, set the capacity
to zero, to avoid the disk partition scanning during boot. We still
create the block device in /dev such that the user may unlock the
device using e.g. hdparm (me)
* tag 'ata-6.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-core: Set capacity to zero for a security locked drive
ata: libata-scsi: Fix system suspend for a security locked drive
ata: libata-scsi: Add missing scsi_device_put() in ata_scsi_dev_rescan()
Pull pin control fixes from Linus Walleij:
- Fix register naming in the Mediatek mt8189 driver
- Select REGMAP_MMIO for the Realtek RTD driver
- Fix the number of items in groups in the Toshiba Visconti driver
- Fix a memory leak in the Cirrus CS42L43 driver
- Fix a deadlock (!) in Qualcomm pinmux configuration
- Fix use of uninitialized memory and list initialization in the S32CC
pin controller
* tag 'pinctrl-v6.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
dt-bindings: pinctrl: xlnx,versal-pinctrl: Add missing unevaluatedProperties on '^conf' nodes
pinctrl: s32cc: initialize gpio_pin_config::list after kmalloc()
pinctrl: s32cc: fix uninitialized memory in s32_pinctrl_desc
pinctrl: qcom: msm: Fix deadlock in pinmux configuration
pinctrl: cirrus: Fix fwnode leak in cs42l43_pin_probe()
dt-bindings: pinctrl: toshiba,visconti: Fix number of items in groups
pinctrl: realtek: Select REGMAP_MMIO for RTD driver
pinctrl: mediatek: mt8189: align register base names to dt-bindings ones
pinctrl: mediatek: mt8196: align register base names to dt-bindings ones
Pull gpio fixes from Bartosz Golaszewski:
- fix a use-after-free bug in GPIO character device code
- update MAINTAINERS
* tag 'gpio-fixes-for-v6.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
MAINTAINERS: update my email address
gpio: cdev: make sure the cdev fd is still active before emitting events
Fully initialize *ctx, including the buf field which sha256_init()
doesn't initialize, to avoid a KMSAN warning when comparing *ctx to
orig_ctx. This KMSAN warning slipped in while KMSAN was not working
reliably due to a stackdepot bug, which has now been fixed.
Fixes: 6733968be7 ("lib/crypto: tests: Add tests and benchmark for sha256_finup_2x()")
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20251121033431.34406-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Pull drm fixes from Dave Airlie:
"A range of small fixes across the board, the i915 display
disambiguation is probably the biggest otherwise amdgpu and xe as
usual with tegra, nouveau, radeon and a core atomic fix.
Looks mostly normal.
atomic:
- Return error codes on failed blob creation for planes
nouveau:
- Fix memory leak
tegra:
- Fix device ref counting
- Fix pid ref counting
- Revert booting on Pixel C
xe:
- Fix out-of-bounds access with BIT()
- Fix kunit test checking wrong condition
- Drop duplicate kconfig select
- Fix guc2host irq handler with MSI-X
i915:
- Wildcat Lake and Panther Lake detangled for display fixes
amdgpu:
- DTBCLK gating fix
- EDID fetching retry improvements
- HDMI HPD debounce filtering
- DCN 2.0 cursor fix
- DP MST PBN fix
- VPE fix
- GC 11 fix
- PRT fix
- MMIO remap page fix
- SR-IOV fix
radeon:
- Fence deadlock fix"
* tag 'drm-fixes-2025-11-21' of https://gitlab.freedesktop.org/drm/kernel: (25 commits)
drm/amdgpu: Add sriov vf check for VCN per queue reset support.
drm/amdgpu/ttm: Fix crash when handling MMIO_REMAP in PDE flags
drm/amdgpu/vm: Check PRT uAPI flag instead of PTE flag
drm/amdgpu: Skip emit de meta data on gfx11 with rs64 enabled
drm/amd: Skip power ungate during suspend for VPE
drm/plane: Fix create_in_format_blob() return value
drm/xe/irq: Handle msix vector0 interrupt
drm/xe: Remove duplicate DRM_EXEC selection from Kconfig
drm/xe/kunit: Fix forcewake assertion in mocs test
drm/xe: Prevent BIT() overflow when handling invalid prefetch region
drm/radeon: delete radeon_fence_process in is_signaled, no deadlock
drm/amd/display: Fix pbn to kbps Conversion
drm/amd/display: Clear the CUR_ENABLE register on DCN20 on DPP5
drm/amd/display: Add an HPD filter for HDMI
drm/amd/display: Increase DPCD read retries
drm/amd/display: Move sleep into each retry for retrieve_link_cap()
drm/amd/display: Prevent Gating DTBCLK before It Is Properly Latched
drm/i915/xe3: Restrict PTL intel_encoder_is_c10phy() to only PHY A
drm/i915/display: Add definition for wcl as subplatform
drm/pcids: Split PTL pciids group to make wcl subplatform
...
Apparently as of version 2.42, glibc headers define AT_RENAME_NOREPLACE
and some of the other flags for renameat2() and friends in <stdio.h>.
Which would all be fine, except for inexplicable reasons glibc decided
to define them _differently_ from the kernel definitions, which then
makes some of our sample code that includes both kernel headers and user
space headers unhappy, because the compiler will (correctly) complain
about redefining things.
Now, mixing kernel headers and user space headers is always a somewhat
iffy proposition due to namespacing issues, but it's kind of inevitable
in our sample and selftest code. And this is just glibc being stupid.
Those defines come from the kernel, glibc is exposing the kernel
interfaces, and glibc shouldn't make up some random new expressions for
these values.
It's not like glibc headers changed the actual result values, but they
arbitrarily just decided to use a different expression to describe those
values. The kernel just does
#define AT_RENAME_NOREPLACE 0x0001
while glibc does
# define RENAME_NOREPLACE (1 << 0)
# define AT_RENAME_NOREPLACE RENAME_NOREPLACE
instead. Same value in the end, but very different macro definition.
For absolutely no reason.
This has since been fixed in the glibc development tree, so eventually
we'll end up with the canonical expressions and no clashes. But in the
meantime the broken headers are in the glibc-2.42 release and have made
it out into distributions.
Do a minimal work-around to make the samples build cleanly by just
undefining the affected macros in between the user space header include
and the kernel header includes.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 69896119dc ("MIPS: vdso: Switch to generic storage
implementation") switches to a generic vdso storage, which increases
the number of data pages from 1 to 4. But there is only one page
reserved, which causes segementation faults depending where the VDSO
area is randomized to. To fix this use the same size of reservation
and allocation of the VDSO data pages.
Fixes: 69896119dc ("MIPS: vdso: Switch to generic storage implementation")
Reviewed-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Depending on the particular CPU implementation a TLB shutdown may occur
if multiple matching entries are detected upon the execution of a TLBP
or the TLBWI/TLBWR instructions. Given that we don't know what entries
we have been handed we need to be very careful with the initial TLB
setup and avoid all these instructions.
Therefore read all the TLB entries one by one with the TLBR instruction,
bypassing the content addressing logic, and truncate any large pages in
place so as to avoid a case in the second step where an incoming entry
for a large page at a lower address overlaps with a replacement entry
chosen at another index. Then preinitialize the TLB using addresses
outside our usual unique range and avoiding clashes with any entries
received, before making the usual call to local_flush_tlb_all().
This fixes (at least) R4x00 cores if TLBP hits multiple matching TLB
entries (SGI IP22 PROM for examples sets up all TLBs to the same virtual
address).
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 35ad7e1815 ("MIPS: mm: tlb-r4k: Uniquify TLB entries on init")
Cc: stable@vger.kernel.org
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com> # Boston I6400, M5150 sim
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Along with the renaming from task_security_struct to cred_security_struct,
rename the local variables to "crsec" from "tsec". This both fits with
existing conventions and helps distinguish between task and cred related
variables.
No functional changes.
Acked-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
The avdcache is meant to be per-task; move it to a new
task_security_struct that is duplicated per-task.
Cc: stable@vger.kernel.org
Fixes: 5d7ddc59b3 ("selinux: reduce path walk overhead")
Signed-off-by: Stephen Smalley <stephen.smalley.work@gmail.com>
[PM: line length fixes]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Before Linux had cred structures, the SELinux task_security_struct was
per-task and although the structure was switched to being per-cred
long ago, the name was never updated. This change renames it to
cred_security_struct to avoid confusion and pave the way for the
introduction of an actual per-task security structure for SELinux. No
functional change.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Pull sched_ext fix from Tejun Heo:
"One low risk and obvious fix: scx_enable() was dereferencing an error
pointer on helper kthread creation failure. Fixed"
* tag 'sched_ext-for-6.18-rc6-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
sched_ext: Fix scx_enable() crash on helper kthread creation failure
A crash was observed when the sched_ext selftests runner was
terminated with Ctrl+\ while test 15 was running:
NIP [c00000000028fa58] scx_enable.constprop.0+0x358/0x12b0
LR [c00000000028fa2c] scx_enable.constprop.0+0x32c/0x12b0
Call Trace:
scx_enable.constprop.0+0x32c/0x12b0 (unreliable)
bpf_struct_ops_link_create+0x18c/0x22c
__sys_bpf+0x23f8/0x3044
sys_bpf+0x2c/0x6c
system_call_exception+0x124/0x320
system_call_vectored_common+0x15c/0x2ec
kthread_run_worker() returns an ERR_PTR() on failure rather than NULL,
but the current code in scx_alloc_and_add_sched() only checks for a NULL
helper. Incase of failure on SIGQUIT, the error is not handled in
scx_alloc_and_add_sched() and scx_enable() ends up dereferencing an
error pointer.
Error handling is fixed in scx_alloc_and_add_sched() to propagate
PTR_ERR() into ret, so that scx_enable() jumps to the existing error
path, avoiding random dereference on failure.
Fixes: bff3b5aec1 ("sched_ext: Move disable machinery into scx_sched")
Cc: stable@vger.kernel.org # v6.16+
Reported-and-tested-by: Samir Mulani <samir@linux.ibm.com>
Signed-off-by: Saket Kumar Bhaskar <skb99@linux.ibm.com>
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com>
Reviewed-by: Andrea Righi <arighi@nvidia.com>
Reviewed-by: Vishal Chourasia <vishalc@linux.ibm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
If timestamp retriving needs to be retried and the local list of
SKB's already has entries, then it's spliced back into the socket
queue. However, the arguments for the splice helper are transposed,
causing exactly the wrong direction of splicing into the on-stack
list. Fix that up.
Cc: stable@vger.kernel.org
Reported-by: Google Big Sleep <big-sleep-vuln-reports+bigsleep-462435176@google.com>
Fixes: 9e4ed359b8 ("io_uring/netcmd: add tx timestamping cmd support")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull power management fix from Rafael Wysocki:
"Fix a regression introduced during the 6.16 development cycle that may
cause runtime PM to be enabled by mistake for devices that do not
support it (which may lead to some serious trouble) if there is a
system wakeup event during the "late suspend" phase of system suspend"
* tag 'pm-6.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: sleep: core: Fix runtime PM enabling in device_resume_early()
Pull ACPI fix from Rafael Wysocki:
"This fixes EINJV2 support introduced during the 6.17 cycle by
unbreaking the initialization broken by a previous attempted fix,
adding sanity checks for data coming from the platform firmware, and
updating the code to handle injecting legacy error types on an EINJV2
capable systems properly (Tony Luck)"
* tag 'acpi-6.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: APEI: EINJ: Fix EINJV2 initialization and injection
Pull x86 platform driver fixes from Ilpo Järvinen:
"This one has lots of new HW entries which adds to the size in diffstat
but the individual changes are simple.
Fixes
- acer-wmi: Ignore backlight event
- alienware-wmi-wmax: Fix quirk match table order & drop redundant
entries
- amd/pmc:
- Add Xbox Ally to spurious 8042 quirk list
- Quirk list Lenovo Legion Go 2 NVMe resume
- msi-wmi-platform:
- Correct GUID to uppercase
- GUID is uncleverly copy-pasted from an example so add a DMI
whitelist
- intel/speed_select_if: PCIBIOS_* return code conversion
- intel-uncore-freq & ISST: Fix kernel doc warnings
New HW support
- alienware-wmi-wmax:
- Alienware 16 Aurora support
- Alienware M support
- Alienware X support
- Dell G support
- amd/pmc:
- ROG Xbox Ally (non-X) support
- huaway-wmi: HONOR MagicBoox X16/X14 PrintScreen & YOYO keys
- hp-wmi:
- Omen 16-wf1xxx fan support
- Omen MAX 16-ah0xx fan + thermal profile support
- Victus 16-r0 and 16-s0 fan + thermal profile support
- intel/hid: Intel Nova Lake support
- intel-uncore-freq:
- Intel Panther Lake support
- Intel Wildcat Lake support
- Intel Nova Lake support"
* tag 'platform-drivers-x86-v6.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (21 commits)
platform/x86: intel-uncore-freq: fix all header kernel-doc warnings
platform/x86: acer-wmi: Ignore backlight event
platform/x86/intel/speed_select_if: Convert PCIBIOS_* return codes to errnos
platform/x86/intel/hid: Add Nova Lake support
platform/x86: alienware-wmi-wmax: Add AWCC support to Alienware 16 Aurora
platform/x86: hp-wmi: Add Omen MAX 16-ah0xx fan support and thermal profile
platform/x86: msi-wmi-platform: Fix typo in WMI GUID
platform/x86: msi-wmi-platform: Only load on MSI devices
platform/x86/amd: pmc: Add Lenovo Legion Go 2 to pmc quirk list
platform/x86/amd/pmc: Add spurious_8042 to Xbox Ally
platform/x86/amd/pmc: Add support for Van Gogh SoC
platform/x86: alienware-wmi-wmax: Add support for the whole "G" family
platform/x86: alienware-wmi-wmax: Add support for the whole "X" family
platform/x86: alienware-wmi-wmax: Add support for the whole "M" family
platform/x86: alienware-wmi-wmax: Drop redundant DMI entries
platform/x86: alienware-wmi-wmax: Fix "Alienware m16 R1 AMD" quirk order
platform/x86: ISST: isst_if.h: fix all kernel-doc warnings
platform/x86: intel-uncore-freq: Add additional client processors
platform/x86: hp-wmi: Add Omen 16-wf1xxx fan support
platform/x86: huawei-wmi: add keys for HONOR models
...
Pull networking fixes from Jakub Kicinski:
"Including fixes from IPsec and wireless.
Previous releases - regressions:
- prevent NULL deref in generic_hwtstamp_ioctl_lower(),
newer APIs don't populate all the pointers in the request
- phylink: add missing supported link modes for the fixed-link
- mptcp: fix false positive warning in mptcp_pm_nl_rm_addr
Previous releases - always broken:
- openvswitch: remove never-working support for setting NSH fields
- xfrm: number of fixes for error paths of xfrm_state creation/
modification/deletion
- xfrm: fixes for offload
- fix the determination of the protocol of the inner packet
- don't push locally generated packets directly to L2 tunnel
mode offloading, they still need processing from the standard
xfrm path
- mptcp: fix a couple of corner cases in fallback and fastclose
handling
- wifi: rtw89: hw_scan: prevent connections from getting stuck,
work around apparent bug in FW by tweaking messages we send
- af_unix: fix duplicate data if PEEK w/ peek_offset needs to wait
- veth: more robust handing of race to avoid txq getting stuck
- eth: ps3_gelic_net: handle skb allocation failures"
* tag 'net-6.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
vsock: Ignore signal/timeout on connect() if already established
be2net: pass wrb_params in case of OS2BMC
l2tp: reset skb control buffer on xmit
net: dsa: microchip: lan937x: Fix RGMII delay tuning
selftests: mptcp: add a check for 'add_addr_accepted'
mptcp: fix address removal logic in mptcp_pm_nl_rm_addr
selftests: mptcp: join: userspace: longer timeout
selftests: mptcp: join: endpoints: longer timeout
selftests: mptcp: join: fastclose: remove flaky marks
mptcp: fix duplicate reset on fastclose
mptcp: decouple mptcp fastclose from tcp close
mptcp: do not fallback when OoO is present
mptcp: fix premature close in case of fallback
mptcp: avoid unneeded subflow-level drops
mptcp: fix ack generation for fallback msk
wifi: rtw89: hw_scan: Don't let the operating channel be last
net: phylink: add missing supported link modes for the fixed-link
selftest: af_unix: Add test for SO_PEEK_OFF.
af_unix: Read sk_peek_offset() again after sleeping in unix_stream_read_generic().
net/mlx5: Clean up only new IRQ glue on request_irq() failure
...
tk_aux_sysfs_init() returns immediately on error during the auxiliary clock
initialization loop without cleaning up previously allocated kobjects and
sysfs groups.
If kobject_create_and_add() or sysfs_create_group() fails during loop
iteration, the parent kobjects (tko and auxo) and any previously created
child kobjects are leaked.
Fix this by adding proper error handling with goto labels to ensure all
allocated resources are cleaned up on failure. kobject_put() on the
parent kobjects will handle cleanup of their children.
Fixes: 7b95663a3d ("timekeeping: Provide interface to control auxiliary clocks")
Signed-off-by: Malaya Kumar Rout <mrout@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/20251120150213.246777-1-mrout@redhat.com
be_insert_vlan_in_pkt() is called with the wrb_params argument being NULL
at be_send_pkt_to_bmc() call site. This may lead to dereferencing a NULL
pointer when processing a workaround for specific packet, as commit
bc0c3405ab ("be2net: fix a Tx stall bug caused by a specific ipv6
packet") states.
The correct way would be to pass the wrb_params from be_xmit().
Fixes: 760c295e0e ("be2net: Support for OS2BMC.")
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Vatoropin <a.vatoropin@crpt.ru>
Link: https://patch.msgid.link/20251119105015.194501-1-a.vatoropin@crpt.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For Security locked drives (drives that have Security enabled, and have
not been Security unlocked by boot firmware), the automatic partition
scanning will result in the user being spammed with errors such as:
ata5.00: failed command: READ DMA
ata5.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 7 dma 4096 in
res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
ata5.00: status: { DRDY ERR }
ata5.00: error: { ABRT }
sd 4:0:0:0: [sda] tag#7 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
sd 4:0:0:0: [sda] tag#7 Sense Key : Aborted Command [current]
sd 4:0:0:0: [sda] tag#7 Add. Sense: No additional sense information
during boot, because most commands except for IDENTIFY will be aborted by
a Security locked drive.
For a Security locked drive, set capacity to zero, so that no automatic
partition scanning will happen.
If the user later unlocks the drive using e.g. hdparm, the close() by the
user space application should trigger a revalidation of the drive.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Commit cf3fc03762 ("ata: libata-scsi: Fix ata_to_sense_error() status
handling") fixed ata_to_sense_error() to properly generate sense key
ABORTED COMMAND (without any additional sense code), instead of the
previous bogus sense key ILLEGAL REQUEST with the additional sense code
UNALIGNED WRITE COMMAND, for a failed command.
However, this broke suspend for Security locked drives (drives that have
Security enabled, and have not been Security unlocked by boot firmware).
The reason for this is that the SCSI disk driver, for the Synchronize
Cache command only, treats any sense data with sense key ILLEGAL REQUEST
as a successful command (regardless of ASC / ASCQ).
After commit cf3fc03762 ("ata: libata-scsi: Fix ata_to_sense_error()
status handling") the code that treats any sense data with sense key
ILLEGAL REQUEST as a successful command is no longer applicable, so the
command fails, which causes the system suspend to be aborted:
sd 1:0:0:0: PM: dpm_run_callback(): scsi_bus_suspend returns -5
sd 1:0:0:0: PM: failed to suspend async: error -5
PM: Some devices failed to suspend, or early wake event detected
To make suspend work once again, for a Security locked device only,
return sense data LOGICAL UNIT ACCESS NOT AUTHORIZED, the actual sense
data which a real SCSI device would have returned if locked.
The SCSI disk driver treats this sense data as a successful command.
Cc: stable@vger.kernel.org
Reported-by: Ilia Baryshnikov <qwelias@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220704
Fixes: cf3fc03762 ("ata: libata-scsi: Fix ata_to_sense_error() status handling")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
The L2TP stack did not reset the skb control buffer before sending the
encapsulated package.
In a setup with an ath10k radio and batman-adv over an L2TP tunnel
massive fragmentations happen sporadically if the L2TP tunnel is
established over IPv4.
L2TP might reset some of the fields in the IP control buffer, but L2TP
assumes the type of the control buffer to be of an IPv4 packet.
In case the L2TP interface is used as a batadv hardif or the packet is
an IPv6 packet, this assumption breaks.
Clear the entire control buffer to avoid such mishaps altogether.
Fixes: f77ae93904 ("[PPPOL2TP]: Reset meta-data in xmit function")
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://patch.msgid.link/20251118001619.242107-1-mail@david-bauer.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Correct RGMII delay application logic in lan937x_set_tune_adj().
The function was missing `data16 &= ~PORT_TUNE_ADJ` before setting the
new delay value. This caused the new value to be bitwise-OR'd with the
existing PORT_TUNE_ADJ field instead of replacing it.
For example, when setting the RGMII 2 TX delay on port 4, the
intended TUNE_ADJUST value of 0 (RGMII_2_TX_DELAY_2NS) was
incorrectly OR'd with the default 0x1B (from register value 0xDA3),
leaving the delay at the wrong setting.
This patch adds the missing mask to clear the field, ensuring the
correct delay value is written. Physical measurements on the RGMII TX
lines confirm the fix, showing the delay changing from ~1ns (before
change) to ~2ns.
While testing on i.MX 8MP showed this was within the platform's timing
tolerance, it did not match the intended hardware-characterized value.
Fixes: b19ac41faa ("net: dsa: microchip: apply rgmii tx and rx delay in phylink mac config")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20251114090951.4057261-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
xfs/286 produced this report on my test fleet:
==================================================================
BUG: KFENCE: out-of-bounds read in memcpy_orig+0x54/0x110
Out-of-bounds read at 0xffff88843fe9e038 (184B right of kfence-#184):
memcpy_orig+0x54/0x110
xrep_symlink_salvage_inline+0xb3/0xf0 [xfs]
xrep_symlink_salvage+0x100/0x110 [xfs]
xrep_symlink+0x2e/0x80 [xfs]
xrep_attempt+0x61/0x1f0 [xfs]
xfs_scrub_metadata+0x34f/0x5c0 [xfs]
xfs_ioc_scrubv_metadata+0x387/0x560 [xfs]
xfs_file_ioctl+0xe23/0x10e0 [xfs]
__x64_sys_ioctl+0x76/0xc0
do_syscall_64+0x4e/0x1e0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
kfence-#184: 0xffff88843fe9df80-0xffff88843fe9dfea, size=107, cache=kmalloc-128
allocated by task 3470 on cpu 1 at 263329.131592s (192823.508886s ago):
xfs_init_local_fork+0x79/0xe0 [xfs]
xfs_iformat_local+0xa4/0x170 [xfs]
xfs_iformat_data_fork+0x148/0x180 [xfs]
xfs_inode_from_disk+0x2cd/0x480 [xfs]
xfs_iget+0x450/0xd60 [xfs]
xfs_bulkstat_one_int+0x6b/0x510 [xfs]
xfs_bulkstat_iwalk+0x1e/0x30 [xfs]
xfs_iwalk_ag_recs+0xdf/0x150 [xfs]
xfs_iwalk_run_callbacks+0xb9/0x190 [xfs]
xfs_iwalk_ag+0x1dc/0x2f0 [xfs]
xfs_iwalk_args.constprop.0+0x6a/0x120 [xfs]
xfs_iwalk+0xa4/0xd0 [xfs]
xfs_bulkstat+0xfa/0x170 [xfs]
xfs_ioc_fsbulkstat.isra.0+0x13a/0x230 [xfs]
xfs_file_ioctl+0xbf2/0x10e0 [xfs]
__x64_sys_ioctl+0x76/0xc0
do_syscall_64+0x4e/0x1e0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
CPU: 1 UID: 0 PID: 1300113 Comm: xfs_scrub Not tainted 6.18.0-rc4-djwx #rc4 PREEMPT(lazy) 3d744dd94e92690f00a04398d2bd8631dcef1954
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-4.module+el8.8.0+21164+ed375313 04/01/2014
==================================================================
On further analysis, I realized that the second parameter to min() is
not correct. xfs_ifork::if_bytes is the size of the xfs_ifork::if_data
buffer. if_bytes can be smaller than the data fork size because:
(a) the forkoff code tries to keep the data area as large as possible
(b) for symbolic links, if_bytes is the ondisk file size + 1
(c) forkoff is always a multiple of 8.
Case in point: for a single-byte symlink target, forkoff will be
8 but the buffer will only be 2 bytes long.
In other words, the logic here is wrong and we walk off the end of the
incore buffer. Fix that.
Cc: stable@vger.kernel.org # v6.10
Fixes: 2651923d8d ("xfs: online repair of symbolic links")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
Currently cpu-clock event always returns 0 count, e.g.,
perf stat -e cpu-clock -- sleep 1
Performance counter stats for 'sleep 1':
0 cpu-clock # 0.000 CPUs utilized
1.002308394 seconds time elapsed
The root cause is the commit 'bc4394e5e79c ("perf: Fix the throttle
error of some clock events")' adds PERF_EF_UPDATE flag check before
calling cpu_clock_event_update() to update the count, however the
PERF_EF_UPDATE flag is never set when the cpu-clock event is stopped in
counting mode (pmu->dev() -> cpu_clock_event_del() ->
cpu_clock_event_stop()). This leads to the cpu-clock event count is
never updated.
To fix this issue, force to set PERF_EF_UPDATE flag for cpu-clock event
just like what task-clock does.
Fixes: bc4394e5e7 ("perf: Fix the throttle error of some clock events")
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ian Rogers <irogers@google.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: https://patch.msgid.link/20251112080526.3971392-1-dapeng1.mi@linux.intel.com
Add proper cleanup of ctx->source and fc->source to the
cifs_parse_mount_err error handler. This ensures that memory allocated
for the source strings is correctly freed on all error paths, matching
the cleanup already performed in the success path by
smb3_cleanup_fs_context_contents().
Pointers are also set to NULL after freeing to prevent potential
double-free issues.
This change fixes a memory leak originally detected by syzbot. The
leak occurred when processing Opt_source mount options if an error
happened after ctx->source and fc->source were successfully
allocated but before the function completed.
The specific leak sequence was:
1. ctx->source = smb3_fs_context_fullpath(ctx, '/') allocates memory
2. fc->source = kstrdup(ctx->source, GFP_KERNEL) allocates more memory
3. A subsequent error jumps to cifs_parse_mount_err
4. The old error handler freed passwords but not the source strings,
causing the memory to leak.
This issue was not addressed by commit e8c73eb7db ("cifs: client:
fix memory leak in smb3_fs_context_parse_param"), which only fixed
leaks from repeated fsconfig() calls but not this error path.
Patch updated with minor change suggested by kernel test robot
Reported-by: syzbot+87be6809ed9bf6d718e3@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=87be6809ed9bf6d718e3
Fixes: 24e0a1eff9 ("cifs: switch to new mount api")
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Shaurya Rane <ssrane_b23@ee.vjti.ac.in>
Signed-off-by: Steve French <stfrench@microsoft.com>
Replace close_cached_dir() calls under cfid_list_lock with a new
close_cached_dir_locked() variant that uses kref_put() instead of
kref_put_lock() to avoid recursive locking when dropping references.
While the existing code works if the refcount >= 2 invariant holds,
this area has proven error-prone. Make deadlocks impossible and WARN
on invariant violations.
Cc: stable@vger.kernel.org
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Henrique Carvalho <henrique.carvalho@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The current LoongArch BPF trampoline implementation is incompatible
with tracing functions in kernel modules. This causes several severe
and user-visible problems:
* The `bpf_selftests/module_attach` test fails consistently.
* Kernel lockup when a BPF program is attached to a module function [1].
* Critical kernel modules like WireGuard experience traffic disruption
when their functions are traced with fentry [2].
Given the severity and the potential for other unknown side-effects, it
is safest to disable the feature entirely for now. This patch prevents
the BPF subsystem from allowing trampoline attachments to kernel module
functions on LoongArch.
This is a temporary mitigation until the core issues in the trampoline
code for kernel module handling can be identified and fixed.
[root@fedora bpf]# ./test_progs -a module_attach -v
bpf_testmod.ko is already unloaded.
Loading bpf_testmod.ko...
Successfully loaded bpf_testmod.ko.
test_module_attach:PASS:skel_open 0 nsec
test_module_attach:PASS:set_attach_target 0 nsec
test_module_attach:PASS:set_attach_target_explicit 0 nsec
test_module_attach:PASS:skel_load 0 nsec
libbpf: prog 'handle_fentry': failed to attach: -ENOTSUPP
libbpf: prog 'handle_fentry': failed to auto-attach: -ENOTSUPP
test_module_attach:FAIL:skel_attach skeleton attach failed: -524
Summary: 0/0 PASSED, 0 SKIPPED, 1 FAILED
Successfully unloaded bpf_testmod.ko.
[1]: https://lore.kernel.org/loongarch/CAK3+h2wDmpC-hP4u4pJY8T-yfKyk4yRzpu2LMO+C13FMT58oqQ@mail.gmail.com/
[2]: https://lore.kernel.org/loongarch/CAK3+h2wYcpc+OwdLDUBvg2rF9rvvyc5amfHT-KcFaK93uoELPg@mail.gmail.com/
Cc: stable@vger.kernel.org
Fixes: f9b6b41f0c ("LoongArch: BPF: Add basic bpf trampoline support")
Acked-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Vincent Li <vincent.mc.li@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
If there is no valid cache info detected (may happen in virtual machine)
for pci_dfl_cache_line_size, kernel shouldn't panic. Because in the PCI
core it will be evaluated to (L1_CACHE_BYTES >> 2).
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
If the default state of the interrupt controllers in the first kernel
don't mask any interrupts, it may cause the second kernel to potentially
receive interrupts (which were previously allocated by the first kernel)
immediately after a CPU becomes online during its boot process. These
interrupts cannot be properly routed, leading to bad IRQ issues.
This patch calls machine_kexec_mask_interrupts() to mask all interrupts
during the kexec/kdump process.
Signed-off-by: Tianyang Zhang <zhangtianyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
On physical machine, NUMA node id comes from high bit 44:48 of physical
address. However it is not true on virt machine. With general method, it
comes from ACPI SRAT table.
Here the common function numa_memblks_init() is used to parse NUMA node
information with numa_memblks.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Some processors have no IOCSR.VENDOR and IOCSR.CPUNAME, some processors
have these registers but there is no valid information.
Consolidate CPU names in /proc/cpuinfo:
1. Add "PRID" to display the PRID & Core-Name;
2. Let "Model Name" display "Unknown" if no valid name.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The kernel UAPI headers already contain fixed-width integer types, there
is no need to rely on the libc types. There may not be a libc available
or the libc may not provides the <stdint.h>, like for example on nolibc.
This also aligns the header with the rest of the LoongArch UAPI headers.
Fixes: 803b0fc5c3 ("LoongArch: Add process management")
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-11-18 (idpf, ice)
This series contains updates to idpf and ice drivers.
Emil adds a check for NULL vport_config during removal to avoid NULL
pointer dereference in idpf.
Grzegorz fixes PTP teardown paths to account for some missed cleanups
for ice driver.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: fix PTP cleanup on driver removal in error path
idpf: fix possible vport_config NULL pointer deref in remove
====================
Link: https://patch.msgid.link/20251118235207.2165495-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
mptcp: misc fixes for v6.18-rc7
Here are various unrelated fixes:
- Patch 1: Fix window space computation for fallback connections which
can affect ACK generation. A fix for v5.11.
- Patch 2: Avoid unneeded subflow-level drops due to unsynced received
window. A fix for v5.11.
- Patch 3: Avoid premature close for fallback connections with PREEMPT
kernels. A fix for v5.12.
- Patch 4: Reset instead of fallback in case of data in the MPTCP
out-of-order queue. A fix for v5.7.
- Patches 5-7: Avoid also sending "plain" TCP reset when closing with an
MP_FASTCLOSE. A fix for v6.1.
- Patches 8-9: Longer timeout for background connections in MPTCP Join
selftests. An additional fix for recent patches for v5.13/v6.1.
- Patches 10-11: Fix typo in a check introduce in a recent refactoring.
A fix for v6.15.
====================
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-0-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous patch fixed an issue with the 'add_addr_accepted' counter.
This was not spot by the test suite.
Check this counter and 'add_addr_signal' in MPTCP Join 'delete re-add
signal' test. This should help spotting similar regressions later on.
These counters are crucial for ensuring the MPTCP path manager correctly
handles the subflow creation via 'ADD_ADDR'.
Signed-off-by: Gang Yan <yangang@kylinos.cn>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-11-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In rare cases, when the test environment is very slow, some userspace
tests can fail because some expected events have not been seen.
Because the tests are expecting a long on-going connection, and they are
not waiting for the end of the transfer, it is fine to have a longer
timeout, and even go over the default one. This connection will be
killed at the end, after the verifications: increasing the timeout
doesn't change anything, apart from avoiding it to end before the end of
the verifications.
To play it safe, all userspace tests not waiting for the end of the
transfer are now having a longer timeout: 2 minutes.
The Fixes commit was making the connection longer, but still, the
default timeout would have stopped it after 1 minute, which might not be
enough in very slow environments.
Fixes: 290493078b ("selftests: mptcp: join: userspace: longer transfer")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-9-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In rare cases, when the test environment is very slow, some endpoints
tests can fail because some expected events have not been seen.
Because the tests are expecting a long on-going connection, and they are
not waiting for the end of the transfer, it is fine to have a longer
timeout, and even go over the default one. This connection will be
killed at the end, after the verifications: increasing the timeout
doesn't change anything, apart from avoiding it to end before the end of
the verifications.
To play it safe, all endpoints tests not waiting for the end of the
transfer are now having a longer timeout: 2 minutes.
The Fixes commit was making the connection longer, but still, the
default timeout would have stopped it after 1 minute, which might not be
enough in very slow environments.
Fixes: 6457595db9 ("selftests: mptcp: join: endpoints: longer transfer")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-8-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CI reports sporadic failures of the fastclose self-tests. The root
cause is a duplicate reset, not carrying the relevant MPTCP option.
In the failing scenario the bad reset is received by the peer before
the fastclose one, preventing the reception of the latter.
Indeed there is window of opportunity at fastclose time for the
following race:
mptcp_do_fastclose
__mptcp_close_ssk
__tcp_close()
tcp_set_state() [1]
tcp_send_active_reset() [2]
After [1] the stack will send reset to in-flight data reaching the now
closed port. Such reset may race with [2].
Address the issue explicitly sending a single reset on fastclose before
explicitly moving the subflow to close status.
Fixes: d21f834855 ("mptcp: use fastclose on more edge scenarios")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/596
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-6-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With the current fastclose implementation, the mptcp_do_fastclose()
helper is in charge of two distinct actions: send the fastclose reset
and cleanup the subflows.
Formally decouple the two steps, ensuring that mptcp explicitly closes
all the subflows after the mentioned helper.
This will make the upcoming fix simpler, and allows dropping the 2nd
argument from mptcp_destroy_common(). The Fixes tag is then the same as
in the next commit to help with the backports.
Fixes: d21f834855 ("mptcp: use fastclose on more edge scenarios")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-5-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I'm observing very frequent self-tests failures in case of fallback when
running on a CONFIG_PREEMPT kernel.
The root cause is that subflow_sched_work_if_closed() closes any subflow
as soon as it is half-closed and has no incoming data pending.
That works well for regular subflows - MPTCP needs bi-directional
connectivity to operate on a given subflow - but for fallback socket is
race prone.
When TCP peer closes the connection before the MPTCP one,
subflow_sched_work_if_closed() will schedule the MPTCP worker to
gracefully close the subflow, and shortly after will do another schedule
to inject and process a dummy incoming DATA_FIN.
On CONFIG_PREEMPT kernel, the MPTCP worker can kick-in and close the
fallback subflow before subflow_sched_work_if_closed() is able to create
the dummy DATA_FIN, unexpectedly interrupting the transfer.
Address the issue explicitly avoiding closing fallback subflows on when
the peer is only half-closed.
Note that, when the subflow is able to create the DATA_FIN before the
worker invocation, the worker will change the msk state before trying to
close the subflow and will skip the latter operation as the msk will not
match anymore the precondition in __mptcp_close_subflow().
Fixes: f09b0ad55a ("mptcp: close subflow when receiving TCP+FIN")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-3-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rcv window is shared among all the subflows. Currently, MPTCP sync
the TCP-level rcv window with the MPTCP one at tcp_transmit_skb() time.
The above means that incoming data may sporadically observe outdated
TCP-level rcv window and being wrongly dropped by TCP.
Address the issue checking for the edge condition before queuing the
data at TCP level, and eventually syncing the rcv window as needed.
Note that the issue is actually present from the very first MPTCP
implementation, but backports older than the blamed commit below will
range from impossible to useless.
Before:
$ nstat -n; sleep 1; nstat -z TcpExtBeyondWindow
TcpExtBeyondWindow 14 0.0
After:
$ nstat -n; sleep 1; nstat -z TcpExtBeyondWindow
TcpExtBeyondWindow 0 0.0
Fixes: fa3fe2b150 ("mptcp: track window announced to peer")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-2-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mptcp_cleanup_rbuf() needs to know the last most recent, mptcp-level
rcv_wnd sent, and such information is tracked into the msk->old_wspace
field, updated at ack transmission time by mptcp_write_options().
Fallback socket do not add any mptcp options, such helper is never
invoked, and msk->old_wspace value remain stale. That in turn makes
ack generation at recvmsg() time quite random.
Address the issue ensuring mptcp_write_options() is invoked even for
fallback sockets, and just update the needed info in such a case.
The issue went unnoticed for a long time, as mptcp currently overshots
the fallback socket receive buffer autotune significantly. It is going
to change in the near future.
Fixes: e3859603ba ("mptcp: better msk receive window updates")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/594
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-1-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Scanning can be offloaded to the firmware. To that end, the driver
prepares a list of channels to scan, including periodic visits back to
the operating channel, and sends the list to the firmware.
When the channel list is too long to fit in a single H2C message, the
driver splits the list, sends the first part, and tells the firmware to
scan. When the scan is complete, the driver sends the next part of the
list and tells the firmware to scan.
When the last channel that fit in the H2C message is the operating
channel something seems to go wrong in the firmware. It will
acknowledge receiving the list of channels but apparently it will not
do anything more. The AP can't be pinged anymore. The driver still
receives beacons, though.
One way to avoid this is to split the list of channels before the
operating channel.
Affected devices:
* RTL8851BU with firmware 0.29.41.3
* RTL8832BU with firmware 0.29.29.8
* RTL8852BE with firmware 0.29.29.8
The commit 57a5fbe39a ("wifi: rtw89: refactor flow that hw scan handles channel list")
is found by git blame, but it is actually to refine the scan flow, but not
a culprit, so skip Fixes tag.
Reported-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/0abbda91-c5c2-4007-84c8-215679e652e1@gmail.com/
Cc: stable@vger.kernel.org # 6.16+
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/c1e61744-8db4-4646-867f-241b47d30386@gmail.com
The MMIO_REMAP BO is a special 4K IO page that does not have a ttm_tt
behind it. However, amdgpu_ttm_tt_pde_flags() was treating it like
normal TT/doorbell/preempt memory and unconditionally accessed
ttm->caching. For the MMIO_REMAP BO, ttm is NULL, so this leads to a
NULL pointer dereference when computing PDE flags.
Fix this by checking that ttm is non-NULL before reading ttm->caching.
This prevents the crash for MMIO_REMAP and also makes the code more
defensive if other BOs ever come through without a ttm_tt.
Fixes: fb5a52dbe9 ("drm/amdgpu: Implement TTM handling for MMIO_REMAP placement")
Suggested-by: Jesse Zhang <Jesse.Zhang@amd.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Jesse Zhang <Jesse.Zhang@amd.com>
Tested-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 0db94da5a0a1cacda080b9ec8425fcbe4babc141)
This fixes sparse mappings (aka. partially resident textures).
Check the correct flags.
Since a recent refactor, the code works with uAPI flags (for
mapping buffer objects), and not PTE (page table entry) flags.
Fixes: 6716a823d1 ("drm/amdgpu: rework how PTE flags are generated v3")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8feeab26c80635b802f72b3ed986c693ff8f3212)
[Why]
Accoreding to CP updated to RS64 on gfx11,
WRITE_DATA with PREEMPTION_META_MEMORY(dst_sel=8) is illegal for CP FW.
That packet is used for MCBP on F32 based system.
So it would lead to incorrect GRBM write and FW is not handling that
extra case correctly.
[How]
With gfx11 rs64 enabled, skip emit de meta data.
Signed-off-by: Yifan Zha <Yifan.Zha@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8366cd442d226463e673bed5d199df916f4ecbcf)
Cc: stable@vger.kernel.org
During the suspend sequence VPE is already going to be power gated
as part of vpe_suspend(). It's unnecessary to call during calls to
amdgpu_device_set_pg_state().
It actually can expose a race condition with the firmware if s0i3
sequence starts as well. Drop these calls.
Cc: Peyton.Lee@amd.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2a6c826cfeedd7714611ac115371a959ead55bda)
Cc: stable@vger.kernel.org
In commit 0345691b24 ("tick/rcu: Stop allowing RCU_SOFTIRQ in idle") the
new function report_idle_softirq() was created by breaking code out of the
existing can_stop_idle_tick() for kernels v5.18 and newer.
In doing so, the code essentially went from this form:
if (A) {
static int ratelimit;
if (ratelimit < 10 && !C && A&D) {
pr_warn("NOHZ tick-stop error: ...");
ratelimit++;
}
return false;
}
to a new function:
static bool report_idle_softirq(void)
{
static int ratelimit;
if (likely(!A))
return false;
if (ratelimit < 10)
return false;
...
pr_warn("NOHZ tick-stop error: local softirq work is pending, handler #%02x!!!\n",
pending);
ratelimit++;
return true;
}
commit a7e282c777 ("tick/rcu: Fix bogus ratelimit condition") realized
ratelimit was essentially set to zero instead of ten, and hence *no*
softirq pending messages would ever be issued, but "fixed" it as:
- if (ratelimit < 10)
+ if (ratelimit >= 10)
return false;
However, this fix introduced another issue:
When ratelimit is greater than or equal 10, even if A is true, it will
directly return false. While ratelimit in the original code was only used
to control printing and will not affect the return value.
Restore the original logic and restrict ratelimit to control the printk and
not the return value.
Fixes: 0345691b24 ("tick/rcu: Stop allowing RCU_SOFTIRQ in idle")
Fixes: a7e282c777 ("tick/rcu: Fix bogus ratelimit condition")
Signed-off-by: Wen Yang <wen.yang@linux.dev>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/20251119174525.29470-1-wen.yang@linux.dev
Pull Allwinner clk driver fixes from Chen-Yu Tsai:
Just a couple fixes for the A523 family. A couple clocks are marked as
critical, and the lower bound of the audio PLL was lowered to match
the datasheet.
* tag 'sunxi-clk-fixes-for-6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: sun55i-a523-ccu: Lower audio0 pll minimum rate
clk: sunxi-ng: sun55i-a523-r-ccu: Mark bus-r-dma as critical
clk: sunxi-ng: Mark A523 bus-r-cpucfg clock as critical
Pull SoC fixes from Arnd Bergmann:
"These are mainly devicetree fixes for the arm platforms from Rockchips
NXP, ASpeed and Broadcom, addressing issues with accidental
overclocking, pinctrl, network and dtc warnings.
There are additional fixes for regressions with the i.MX reset and
memory controller drivers as well as the Tegra memory controller
driver.
Minor updates to the MAINTAINERS file, tee documentation and
defconfigs bring those up to date with recent changes elsewhere"
* tag 'soc-fixes-6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits)
MAINTAINERS: sync omap devicetree maintainers with omap platform
MAINTAINERS: Update Krzysztof Kozlowski's email
arm64: dts: rockchip: fix PCIe 3.3V regulator voltage on orangepi-5
arm64: dts: rockchip: disable HS400 on RK3588 Tiger
arm64: dts: rockchip: drop reset from rk3576 i2c9 node
tee: <uapi/linux/tee.h: fix all kernel-doc issues
arm64: dts: rockchip: Fix USB power enable pin for BTT CB2 and Pi2
arm64: dts: broadcom: bcm2712: rpi-5: Add ethernet0 alias
arm64: dts: broadcom: Assign clock rates in eth node for RPi5
reset: imx8mp-audiomix: Fix bad mask values
ARM: dts: BCM53573: Fix address of Luxul XAP-1440's Ethernet PHY
arm64: defconfig: Fix V3D deferred probe timeout
arm64: dts: rockchip: Fix vccio4-supply on rk3566-pinetab2
arm64: dts: rockchip: include rk3399-base instead of rk3399 in rk3399-op1
arm64: dts: imx8mp-kontron: Fix USB OTG role switching
arm64: dts: imx95: Fix MSI mapping for PCIe endpoint nodes
arm64: dts: imx8-ss-img: Avoid gpio0_mipi_csi GPIOs being deferred
arm: imx_v6_v7_defconfig: enable ext4 directly
memory: tegra210: Fix incorrect client ids
arm64: dts: rockchip: Fix indentation on rk3399 haikou demo dtso
...
Pull pwm fix from Uwe Kleine-König:
"Correct mismatched pwm chip info for adp5585.
Luke Wang found a problem in the pwm-adp5585 driver about how register
information is mapped to the different device variants. This
effectively made the driver non-functional.
That didn't pop up before because the driver change was developed as
part of a bigger mfd series and the original author didn't retest PWM
functionality after it was tested in an earlier revision but then
reworked"
* tag 'pwm/for-6.18-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: adp5585: Correct mismatched pwm chip info
Pull HID fixes from Jiri Kosina:
- memory leak fixes in hid-uclogic, hid-ntrig and hid-playstation
drivers (Abdun Nihaal, Masami Ichikawa)
- regression fix for playback handling in hid-pidff (Tomasz Pakuła)
- initialization fix for some amd_sfh platforms (Mario Limonciello)
- a few assorted device-specific ID additions and quirks
* tag 'hid-for-linus-2025111901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: uclogic: Fix potential memory leak in error path
HID: playstation: Fix memory leak in dualshock4_get_calibration_data()
HID: pidff: Fix needs_playback check
HID: corsair-void: Use %pe for printing PTR_ERR
HID: elecom: Add support for ELECOM M-XT3URBK (018F)
HID: hid-input: Extend Elan ignore battery quirk to USB
HID: hid-ntrig: Prevent memory leak in ntrig_report_version()
HID: amd_sfh: Stop sensor before starting
HID: apple: Add SONiX AK870 PRO to non_apple_keyboards quirk list
HID: lenovo: fixup Lenovo Yoga Slim 7x Keyboard rdesc
HID: quirks: work around VID/PID conflict for 0x4c4a/0x4155
Pause, Asym_Pause and Autoneg bits are not set when pl->supported is
initialized, so these link modes will not work for the fixed-link. This
leads to a TCP performance degradation issue observed on the i.MX943
platform.
The switch CPU port of i.MX943 is connected to an ENETC MAC, this link
is a fixed link and the link speed is 2.5Gbps. And one of the switch
user ports is the RGMII interface, and its link speed is 1Gbps. If the
flow-control of the fixed link is not enabled, we can easily observe
the iperf performance of TCP packets is very low. Because the inbound
rate on the CPU port is greater than the outbound rate on the user port,
the switch is prone to congestion, leading to the loss of some TCP
packets and requiring multiple retransmissions.
Solving this problem should be as simple as setting the Asym_Pause and
Pause bits. The reason why the Autoneg bit needs to be set, Russell
has gave a very good explanation in the thread [1], see below.
"As the advertising and lp_advertising bitmasks have to be non-empty,
and the swphy reports aneg capable, aneg complete, and AN enabled, then
for consistency with that state, Autoneg should be set. This is how it
was prior to the blamed commit."
Fixes: de7d3f87be ("net: phylink: Use phy_caps_lookup for fixed-link configuration")
Link: https://lore.kernel.org/aRjqLN8eQDIQfBjS@shell.armlinux.org.uk # [1]
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20251117102943.1862680-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull memblock fix from Mike Rapoport:
"Fix memblock_estimated_nr_free_pages() for soft-reserved memory
The "soft-reserved" memory regions (EFI_MEMORY_SP) are added to the
memblock.reserved, but not to the memblock.memory. It causes
memblock_estimated_nr_free_pages() to return a value smaller value
than expected, or if it underflows, an extremely large value.
Calculate the number of estimated free pages using
memblock_reserved_kern_size() instead of memblock_reserved_size() to
fix the issue"
* tag 'fixes-2025-11-19' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
memblock: fix memblock_estimated_nr_free_pages() for soft-reserved memory
Add the missing unevaluatedProperties to disallow extra properties on
the '^conf' nodes.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ACPI 6.6 specification for EINJV2 appends an extra structure to
the end of the existing struct set_error_type_with_address.
Several issues showed up in testing.
1) Initialization was broken by an earlier fix [1] since is_v2 is only
set while performing an injection, not during initialization.
2) A buggy BIOS provided invalid "revision" and "length" for the
extension structure. Add several sanity checks.
3) When injecting legacy error types on an EINJV2 capable system,
don't copy the component arrays.
Fixes: 6c70585149 ("ACPI: APEI: EINJ: Check if user asked for EINJV2 injection") # [1]
Fixes: b47610296d ("ACPI: APEI: EINJ: Enable EINJv2 error injections")
Signed-off-by: Tony Luck <tony.luck@intel.com>
[ rjw: Changelog edits ]
Cc: 6.17+ <stable@vger.kernel.org> # 6.17+
Link: https://patch.msgid.link/20251119012712.178715-1-tony.luck@intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the final call to fput() on a file descriptor, the release action
may be deferred and scheduled on a work queue. The reference count of
that descriptor is still zero and it must not be used. It's possible
that a GPIO change, we want to notify the user-space about, happens
AFTER the reference count on the file descriptor associated with the
character device went down to zero but BEFORE the .release() callback
was called from the workqueue and so BEFORE we unregistered from the
notifier.
Using the regular get_file() routine in this situation triggers the
following warning:
struct file::f_count incremented from zero; use-after-free condition present!
So use the get_file_active() variant that will return NULL on file
descriptors that have been or are being released.
Fixes: 40b7c49950 ("gpio: cdev: put emitting the line state events on a workqueue")
Reported-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Closes: https://lore.kernel.org/all/5d605f7fc99456804911403102a4fe999a14cc85.camel@siemens.com/
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20251117-gpio-cdev-get-file-v1-1-28a16b5985b8@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Kuniyuki Iwashima says:
====================
af_unix: Fix SO_PEEK_OFF bug in unix_stream_read_generic().
Miao Wang reported a bug of SO_PEEK_OFF on AF_UNIX SOCK_STREAM socket.
Patch 1 fixes the bug and Patch 2 adds a new selftest to cover the case.
====================
Link: https://patch.msgid.link/20251117174740.3684604-1-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test covers various cases to verify SO_PEEK_OFF behaviour
for all AF_UNIX socket types.
two_chunks_blocking and two_chunks_overlap_blocking reproduce
the issue mentioned in the previous patch.
Without the patch, the two tests fail:
# RUN so_peek_off.stream.two_chunks_blocking ...
# so_peek_off.c:121:two_chunks_blocking:Expected 'bbbb' == 'aaaabbbb'.
# two_chunks_blocking: Test terminated by assertion
# FAIL so_peek_off.stream.two_chunks_blocking
not ok 3 so_peek_off.stream.two_chunks_blocking
# RUN so_peek_off.stream.two_chunks_overlap_blocking ...
# so_peek_off.c:159:two_chunks_overlap_blocking:Expected 'bbbb' == 'aaaabbbb'.
# two_chunks_overlap_blocking: Test terminated by assertion
# FAIL so_peek_off.stream.two_chunks_overlap_blocking
not ok 5 so_peek_off.stream.two_chunks_overlap_blocking
With the patch, all tests pass:
# PASSED: 15 / 15 tests passed.
# Totals: pass:15 fail:0 xfail:0 xpass:0 skip:0 error:0
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20251117174740.3684604-3-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Miao Wang reported a bug of SO_PEEK_OFF on AF_UNIX SOCK_STREAM
socket.
The unexpected behaviour is triggered when the peek offset is
larger than the recv queue and the thread is unblocked by new
data.
Let's assume a socket which has "aaaa" in the recv queue and
the peek offset is 4.
First, unix_stream_read_generic() reads the offset 4 and skips
the skb(s) of "aaaa" with the code below:
skip = max(sk_peek_offset(sk, flags), 0); /* @skip is 4. */
do {
...
while (skip >= unix_skb_len(skb)) {
skip -= unix_skb_len(skb);
...
skb = skb_peek_next(skb, &sk->sk_receive_queue);
if (!skb)
goto again; /* @skip is 0. */
}
The thread jumps to the 'again' label and goes to sleep since
new data has not arrived yet.
Later, new data "bbbb" unblocks the thread, and the thread jumps
to the 'redo:' label to restart the entire process from the first
skb in the recv queue.
do {
...
redo:
...
last = skb = skb_peek(&sk->sk_receive_queue);
...
again:
if (skb == NULL) {
...
timeo = unix_stream_data_wait(sk, timeo, last,
last_len, freezable);
...
goto redo; /* @skip is 0 !! */
However, the peek offset is not reset in the path.
If the buffer size is 8, recv() will return "aaaabbbb" without
skipping any data, and the final offset will be 12 (the original
offset 4 + peeked skbs' length 8).
After sleeping in unix_stream_read_generic(), we have to fetch the
peek offset again.
Let's move the redo label before mutex_lock(&u->iolock).
Fixes: 9f389e3567 ("af_unix: return data from multiple SKBs on recv() with MSG_PEEK flag")
Reported-by: Miao Wang <shankerwangmiao@gmail.com>
Closes: https://lore.kernel.org/netdev/3B969F90-F51F-4B9D-AB1A-994D9A54D460@gmail.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20251117174740.3684604-2-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Steffen Klassert says:
====================
pull request (net): ipsec 2025-11-18
1) Misc fixes for xfrm_state creation/modification/deletion.
Patchset from Sabrina Dubroca.
2) Fix inner packet family determination for xfrm offloads.
From Jianbo Liu.
3) Don't push locally generated packets directly to L2 tunnel
mode offloading, they still need processing from the standard
xfrm path. From Jianbo Liu.
4) Fix memory leaks in xfrm_add_acquire for policy offloads and policy
security contexts. From Zilin Guan.
* tag 'ipsec-2025-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
xfrm: fix memory leak in xfrm_add_acquire()
xfrm: Prevent locally generated packets from direct output in tunnel mode
xfrm: Determine inner GSO type from packet inner protocol
xfrm: Check inner packet family directly from skb_dst
xfrm: check all hash buckets for leftover states during netns deletion
xfrm: set err and extack on failure to create pcpu SA
xfrm: call xfrm_dev_state_delete when xfrm_state_migrate fails to add the state
xfrm: make state as DEAD before final put when migrate fails
xfrm: also call xfrm_state_delete_tunnel at destroy time for states that were never added
xfrm: drop SA reference in xfrm_state_update if dir doesn't match
====================
Link: https://patch.msgid.link/20251118085344.2199815-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function devl_rate_nodes_destroy is documented to "Unset parent for
all rate objects". However, it was only calling the driver-specific
`rate_leaf_parent_set` or `rate_node_parent_set` ops and decrementing
the parent's refcount, without actually setting the
`devlink_rate->parent` pointer to NULL.
This leaves a dangling pointer in the `devlink_rate` struct, which cause
refcount error in netdevsim[1] and mlx5[2]. In addition, this is
inconsistent with the behavior of `devlink_nl_rate_parent_node_set`,
where the parent pointer is correctly cleared.
This patch fixes the issue by explicitly setting `devlink_rate->parent`
to NULL after notifying the driver, thus fulfilling the function's
documented behavior for all rate objects.
[1]
repro steps:
echo 1 > /sys/bus/netdevsim/new_device
devlink dev eswitch set netdevsim/netdevsim1 mode switchdev
echo 1 > /sys/bus/netdevsim/devices/netdevsim1/sriov_numvfs
devlink port function rate add netdevsim/netdevsim1/test_node
devlink port function rate set netdevsim/netdevsim1/128 parent test_node
echo 1 > /sys/bus/netdevsim/del_device
dmesg:
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 8 PID: 1530 at lib/refcount.c:31 refcount_warn_saturate+0x42/0xe0
CPU: 8 UID: 0 PID: 1530 Comm: bash Not tainted 6.18.0-rc4+ #1 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:refcount_warn_saturate+0x42/0xe0
Call Trace:
<TASK>
devl_rate_leaf_destroy+0x8d/0x90
__nsim_dev_port_del+0x6c/0x70 [netdevsim]
nsim_dev_reload_destroy+0x11c/0x140 [netdevsim]
nsim_drv_remove+0x2b/0xb0 [netdevsim]
device_release_driver_internal+0x194/0x1f0
bus_remove_device+0xc6/0x130
device_del+0x159/0x3c0
device_unregister+0x1a/0x60
del_device_store+0x111/0x170 [netdevsim]
kernfs_fop_write_iter+0x12e/0x1e0
vfs_write+0x215/0x3d0
ksys_write+0x5f/0xd0
do_syscall_64+0x55/0x10f0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
[2]
devlink dev eswitch set pci/0000:08:00.0 mode switchdev
devlink port add pci/0000:08:00.0 flavour pcisf pfnum 0 sfnum 1000
devlink port function rate add pci/0000:08:00.0/group1
devlink port function rate set pci/0000:08:00.0/32768 parent group1
modprobe -r mlx5_ib mlx5_fwctl mlx5_core
dmesg:
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 7 PID: 16151 at lib/refcount.c:31 refcount_warn_saturate+0x42/0xe0
CPU: 7 UID: 0 PID: 16151 Comm: bash Not tainted 6.17.0-rc7_for_upstream_min_debug_2025_10_02_12_44 #1 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
RIP: 0010:refcount_warn_saturate+0x42/0xe0
Call Trace:
<TASK>
devl_rate_leaf_destroy+0x8d/0x90
mlx5_esw_offloads_devlink_port_unregister+0x33/0x60 [mlx5_core]
mlx5_esw_offloads_unload_rep+0x3f/0x50 [mlx5_core]
mlx5_eswitch_unload_sf_vport+0x40/0x90 [mlx5_core]
mlx5_sf_esw_event+0xc4/0x120 [mlx5_core]
notifier_call_chain+0x33/0xa0
blocking_notifier_call_chain+0x3b/0x50
mlx5_eswitch_disable_locked+0x50/0x110 [mlx5_core]
mlx5_eswitch_disable+0x63/0x90 [mlx5_core]
mlx5_unload+0x1d/0x170 [mlx5_core]
mlx5_uninit_one+0xa2/0x130 [mlx5_core]
remove_one+0x78/0xd0 [mlx5_core]
pci_device_remove+0x39/0xa0
device_release_driver_internal+0x194/0x1f0
unbind_store+0x99/0xa0
kernfs_fop_write_iter+0x12e/0x1e0
vfs_write+0x215/0x3d0
ksys_write+0x5f/0xd0
do_syscall_64+0x53/0x1f0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Fixes: d755598450 ("devlink: Allow setting parent node of rate objects")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1763381149-1234377-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
s32_pmx_gpio_request_enable() does not initialize the newly-allocated
gpio_pin_config::list before adding it to s32_pinctrl::gpio_configs.
This could result in a linked list corruption.
Initialize the new list_head with INIT_LIST_HEAD() to fix this.
Fixes: fd84aaa817 ("pinctrl: add NXP S32 SoC family support")
Signed-off-by: Jared Kangas <jkangas@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
s32_pinctrl_desc is allocated with devm_kmalloc(), but not all of its
fields are initialized. Notably, num_custom_params is used in
pinconf_generic_parse_dt_config(), resulting in intermittent allocation
errors, such as the following splat when probing i2c-imx:
WARNING: CPU: 0 PID: 176 at mm/page_alloc.c:4795 __alloc_pages_noprof+0x290/0x300
[...]
Hardware name: NXP S32G3 Reference Design Board 3 (S32G-VNP-RDB3) (DT)
[...]
Call trace:
__alloc_pages_noprof+0x290/0x300 (P)
___kmalloc_large_node+0x84/0x168
__kmalloc_large_node_noprof+0x34/0x120
__kmalloc_noprof+0x2ac/0x378
pinconf_generic_parse_dt_config+0x68/0x1a0
s32_dt_node_to_map+0x104/0x248
dt_to_map_one_config+0x154/0x1d8
pinctrl_dt_to_map+0x12c/0x280
create_pinctrl+0x6c/0x270
pinctrl_get+0xc0/0x170
devm_pinctrl_get+0x50/0xa0
pinctrl_bind_pins+0x60/0x2a0
really_probe+0x60/0x3a0
[...]
__platform_driver_register+0x2c/0x40
i2c_adap_imx_init+0x28/0xff8 [i2c_imx]
[...]
This results in later parse failures that can cause issues in dependent
drivers:
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c0-pins/i2c0-grp0: could not parse node property
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c0-pins/i2c0-grp0: could not parse node property
[...]
pca953x 0-0022: failed writing register: -6
i2c i2c-0: IMX I2C adapter registered
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c2-pins/i2c2-grp0: could not parse node property
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c2-pins/i2c2-grp0: could not parse node property
i2c i2c-1: IMX I2C adapter registered
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c4-pins/i2c4-grp0: could not parse node property
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c4-pins/i2c4-grp0: could not parse node property
i2c i2c-2: IMX I2C adapter registered
Fix this by initializing s32_pinctrl_desc with devm_kzalloc() instead of
devm_kmalloc() in s32_pinctrl_probe(), which sets the previously
uninitialized fields to zero.
Fixes: fd84aaa817 ("pinctrl: add NXP S32 SoC family support")
Signed-off-by: Jared Kangas <jkangas@redhat.com>
Tested-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Improve the cleanup on releasing PTP resources in error path.
The error case might happen either at the driver probe and PTP
feature initialization or on PTP restart (errors in reset handling, NVM
update etc). In both cases, calls to PF PTP cleanup (ice_ptp_cleanup_pf
function) and 'ps_lock' mutex deinitialization were missed.
Additionally, ptp clock was not unregistered in the latter case.
Keep PTP state as 'uninitialized' on init to distinguish between error
scenarios and to avoid resource release duplication at driver removal.
The consequence of missing ice_ptp_cleanup_pf call is the following call
trace dumped when ice_adapter object is freed (port list is not empty,
as it is required at this stage):
[ T93022] ------------[ cut here ]------------
[ T93022] WARNING: CPU: 10 PID: 93022 at
ice/ice_adapter.c:67 ice_adapter_put+0xef/0x100 [ice]
...
[ T93022] RIP: 0010:ice_adapter_put+0xef/0x100 [ice]
...
[ T93022] Call Trace:
[ T93022] <TASK>
[ T93022] ? ice_adapter_put+0xef/0x100 [ice
33d2647ad4f6d866d41eefff1806df37c68aef0c]
[ T93022] ? __warn.cold+0xb0/0x10e
[ T93022] ? ice_adapter_put+0xef/0x100 [ice
33d2647ad4f6d866d41eefff1806df37c68aef0c]
[ T93022] ? report_bug+0xd8/0x150
[ T93022] ? handle_bug+0xe9/0x110
[ T93022] ? exc_invalid_op+0x17/0x70
[ T93022] ? asm_exc_invalid_op+0x1a/0x20
[ T93022] ? ice_adapter_put+0xef/0x100 [ice
33d2647ad4f6d866d41eefff1806df37c68aef0c]
[ T93022] pci_device_remove+0x42/0xb0
[ T93022] device_release_driver_internal+0x19f/0x200
[ T93022] driver_detach+0x48/0x90
[ T93022] bus_remove_driver+0x70/0xf0
[ T93022] pci_unregister_driver+0x42/0xb0
[ T93022] ice_module_exit+0x10/0xdb0 [ice
33d2647ad4f6d866d41eefff1806df37c68aef0c]
...
[ T93022] ---[ end trace 0000000000000000 ]---
[ T93022] ice: module unloaded
Fixes: e800654e85 ("ice: Use ice_adapter for PTP shared data instead of auxdev")
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Regulator/supply fixes for a number of boards, removed too fast
cpu OPPs from rk3576 (not supported in newer vendor TF-A and never
supported in upstream TF-A). As well as some DTS validation fixes
and one pinctrl fix for the odroid-m1.
* tag 'v6.18-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: fix PCIe 3.3V regulator voltage on orangepi-5
arm64: dts: rockchip: disable HS400 on RK3588 Tiger
arm64: dts: rockchip: drop reset from rk3576 i2c9 node
arm64: dts: rockchip: Fix USB power enable pin for BTT CB2 and Pi2
arm64: dts: rockchip: Fix vccio4-supply on rk3566-pinetab2
arm64: dts: rockchip: include rk3399-base instead of rk3399 in rk3399-op1
arm64: dts: rockchip: Fix indentation on rk3399 haikou demo dtso
arm64: dts: rockchip: Make RK3588 GPU OPP table naming less generic
arm64: dts: rockchip: Drop 'rockchip,grf' prop from tsadc on rk3328
arm64: dts: rockchip: Remove non-functioning CPU OPPs from RK3576
arm64: dts: rockchip: Fix PCIe power enable pin for BigTreeTech CB2 and Pi2
arm64: dts: rockchip: Set correct pinctrl for I2S1 8ch TX on odroid-m1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Current gu2host handler registered as MSI-X vector 0 and as per bspec for
a msix vector 0 interrupt, the driver must check the legacy registers
190008(TILE_INT_REG), 190060h (GT INTR Identity Reg 0) and other registers
mentioned in "Interrupt Service Routine Pseudocode" otherwise it will block
the next interrupts. To overcome this issue replacing guc2host handler
with legacy xe_irq_handler.
Fixes: da889070be ("drm/xe/irq: Separate MSI and MSI-X flows")
Bspec: 62357
Signed-off-by: Venkata Ramana Nayana <venkata.ramana.nayana@intel.com>
Reviewed-by: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patch.msgid.link/20251107083141.2080189-1-venkata.ramana.nayana@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit c34a14bce7090862ebe5a64abe8d85df75e62737)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
If user provides a large value (such as 0x80) for parameter
prefetch_mem_region_instance in vm_bind ioctl, it will cause
BIT(prefetch_region) overflow as below:
"
------------[ cut here ]------------
UBSAN: shift-out-of-bounds in drivers/gpu/drm/xe/xe_vm.c:3414:7
shift exponent 128 is too large for 64-bit type 'long unsigned int'
CPU: 8 UID: 0 PID: 53120 Comm: xe_exec_system_ Tainted: G W 6.18.0-rc1-lgci-xe-kernel+ #200 PREEMPT(voluntary)
Tainted: [W]=WARN
Hardware name: ASUS System Product Name/PRIME Z790-P WIFI, BIOS 0812 02/24/2023
Call Trace:
<TASK>
dump_stack_lvl+0xa0/0xc0
dump_stack+0x10/0x20
ubsan_epilogue+0x9/0x40
__ubsan_handle_shift_out_of_bounds+0x10e/0x170
? mutex_unlock+0x12/0x20
xe_vm_bind_ioctl.cold+0x20/0x3c [xe]
...
"
Fix it by validating prefetch_region before the BIT() usage.
v2: Add Closes and Cc stable kernels. (Matt)
Reported-by: Koen Koning <koen.koning@intel.com>
Reported-by: Peter Senna Tschudin <peter.senna@linux.intel.com>
Fixes: dd08ebf6c3 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/6478
Cc: <stable@vger.kernel.org> # v6.8+
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patch.msgid.link/20251112181005.2120521-2-shuicheng.lin@intel.com
(cherry picked from commit 8f565bdd14eec5611cc041dba4650e42ccdf71d9)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Pull kvm fixes from Paolo Bonzini:
"Arm:
- Only adjust the ID registers when no irqchip has been created once
per VM run, instead of doing it once per vcpu, as this otherwise
triggers a pretty bad conbsistency check failure in the sysreg code
- Make sure the per-vcpu Fine Grain Traps are computed before we load
the system registers on the HW, as we otherwise start running
without anything set until the first preemption of the vcpu
x86:
- Fix selftests failure on AMD, checking for an optimization that was
not happening anymore"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SVM: Fix redundant updates of LBR MSR intercepts
KVM: arm64: VHE: Compute fgt traps before activating them
KVM: arm64: Finalize ID registers only once per VM
Delete the attempt to progress the queue when checking if fence is
signaled. This avoids deadlock.
dma-fence_ops::signaled can be called with the fence lock in unknown
state. For radeon, the fence lock is also the wait queue lock. This can
cause a self deadlock when signaled() tries to make forward progress on
the wait queue. But advancing the queue is unneeded because incorrectly
returning false from signaled() is perfectly acceptable.
Link: https://github.com/brave/brave-browser/issues/49182
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4641
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Robert McClinton <rbmccav@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 527ba26e50ec2ca2be9c7c82f3ad42998a75d0db)
Cc: stable@vger.kernel.org
[Why]
Existing routine has two conversion sequence,
pbn_to_kbps and kbps_to_pbn with margin.
Non of those has without-margin calculation.
kbps_to_pbn with margin conversion includes
fec overhead which has already been included in
pbn_div calculation with 0.994 factor considered.
It is a double counted fec overhead factor that causes
potential bw loss.
[How]
Add without-margin calculation.
Fix fec overhead double counted issue.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3735
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit e0dec00f3d05e8c0eceaaebfdca217f8d10d380c)
Cc: stable@vger.kernel.org
In uclogic_params_ugee_v2_init_event_hooks(), the memory allocated for
event_hook is not freed in the next error path. Fix that by freeing it.
Fixes: a251d6576d ("HID: uclogic: Handle wireless device reconnection")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
[Why]
On DCN20 & DCN30, the 6th DPP's & HUBP's are powered on permanently and
cannot be power gated. Thus, when dpp_reset() is invoked for the DPP5,
while it's still powered on, the cached cursor_state
(dpp_base->pos.cur0_ctl.bits.cur0_enable)
and the actual state (CUR0_ENABLE) bit are unsycned. This can cause a
double cursor in full screen with non-native scaling.
[How]
Force disable cursor on DPP5 on plane powerdown for ASICs w/ 6 DPPs/HUBPs.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4673
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 79b3c037f972dcb13e325a8eabfb8da835764e15)
Cc: stable@vger.kernel.org
The memory allocated for buf is not freed in the error paths when
ps_get_report() fails. Free buf before jumping to transfer_failed label
Fixes: 947992c7fa ("HID: playstation: DS4: Fix calibration workaround for clone devices")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Reviewed-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
[Why]
Some monitors perform rapid “autoscan” HPD re‑assertions right after a
disconnect or powersaving mode enablement. These appear as a quick
disconnect→reconnect with an identical EDID. Since Linux has no HDMI
hotplug detection (HPD) filter, these quick reconnects are seen as hotplug
events, which can unintentionally wake a system with DPMS off.
An example: https://gitlab.freedesktop.org/drm/amd/-/issues/2876
Such 'fake reconnects' are considered when the interval between a
disconnect and a connect is within 1500ms (experimentally chosen using
several monitors), and the two connections have the same EDID.
[How]
Implement a time-based debounce mechanism:
1. On HDMI disconnect detection, instead of immediately processing the
HPD event, save the current sink and schedule delayed work (default 1500ms)
2. If another HDMI disconnect HPD event arrives during the debounce period,
it reschedules the pending work, ensuring only the final state is processed.
3. When the debounce timer expires, re-detect the display and compare the
new sink with the cached one using EDID comparison.
4. If sinks match (same EDID), this was a spontaneous HPD toggle:
- Update connector state internally
- Skip hotplug event to prevent desktop rearrangement
If sinks differ, this was a real display change:
- Process normally with the hotplug event
The debounce delay is configurable via module parameter
'hdmi_hpd_debounce_delay_ms'.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2876
Reviewed-by: Sun peng (Leo) Li <sunpeng.li@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit c918e75e1ed95be76f8e3156a411188f650fe03f)
A small bug made it's way here when rewriting code to Linux quality.
Currently, if an effect is not infinite and a program requests it's
playback with the same number of loops, the play command won't be fired
and if an effect is infinite, the spam will continue.
We want every playback update for non-infinite effects and only some
for infinite (detecting when a program requests stop with 0 which will
be different than previous value which is usually 1 or 255).
Signed-off-by: Tomasz Pakuła <tomasz.pakula.oficjalny@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
[Why]
When a monitor is booting it's possible that it isn't ready to retrieve
link caps and this can lead to an EDID read failure:
```
[drm:retrieve_link_cap [amdgpu]] *ERROR* retrieve_link_cap: Read receiver caps dpcd data failed.
amdgpu 0000:c5:00.0: [drm] *ERROR* No EDID read.
```
[How]
Rather than msleep once and try a few times, msleep each time. Should
be no changes for existing working monitors, but should correct reading
caps on a monitor that is slow to boot.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4672
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 669dca37b3348a447db04bbdcbb3def94d5997cc)
Cc: stable@vger.kernel.org
The ELECOM M-XT3URBK trackball has an additional device ID (0x018F), which
shares the same report descriptor as the existing device (0x00FB). However,
the driver does not currently recognize this new ID, resulting in only five
buttons being functional.
This patch adds the new device ID so that all six buttons work properly.
Signed-off-by: Naoki Ueki <naoki25519@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Don't update the LBR MSR intercept bitmaps if they're already up-to-date,
as unconditionally updating the intercepts forces KVM to recalculate the
MSR bitmaps for vmcb02 on every nested VMRUN. The redundant updates are
functionally okay; however, they neuter an optimization in Hyper-V
nested virtualization enlightenments and this manifests as a self-test
failure.
In particular, Hyper-V lets L1 mark "nested enlightenments" as clean, i.e.
tell KVM that no changes were made to the MSR bitmap since the last VMRUN.
The hyperv_svm_test KVM selftest intentionally changes the MSR bitmap
"without telling KVM about it" to verify that KVM honors the clean hint,
correctly fails because KVM notices the changed bitmap anyway:
==== Test Assertion Failure ====
x86/hyperv_svm_test.c:120: vmcb->control.exit_code == 0x081
pid=193558 tid=193558 errno=4 - Interrupted system call
1 0x0000000000411361: assert_on_unhandled_exception at processor.c:659
2 0x0000000000406186: _vcpu_run at kvm_util.c:1699
3 (inlined by) vcpu_run at kvm_util.c:1710
4 0x0000000000401f2a: main at hyperv_svm_test.c:175
5 0x000000000041d0d3: __libc_start_call_main at libc-start.o:?
6 0x000000000041f27c: __libc_start_main_impl at ??:?
7 0x00000000004021a0: _start at ??:?
vmcb->control.exit_code == SVM_EXIT_VMMCALL
Do *not* fix this by skipping svm_hv_vmcb_dirty_nested_enlightenments()
when svm_set_intercept_for_msr() performs a no-op change. changes to
the L0 MSR interception bitmap are only triggered by full CPUID updates
and MSR filter updates, both of which should be rare. Changing
svm_set_intercept_for_msr() risks hiding unintended pessimizations
like this one, and is actually more complex than this change.
Fixes: fbe5e5f030 ("KVM: nSVM: Always recalculate LBR MSR intercepts in svm_update_lbrv()")
Cc: stable@vger.kernel.org
Signed-off-by: Yosry Ahmed <yosry.ahmed@linux.dev>
Link: https://patch.msgid.link/20251112013017.1836863-1-yosry.ahmed@linux.dev
[Rewritten commit message based on mailing list discussion. - Paolo]
Reviewed-by: Sean Christopherson <seanjc@google.com>
Tested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[why]
1. With allow_0_dtb_clk enabled, the time required to latch DTBCLK to 600 MHz
depends on the SMU. If DTBCLK is not latched to 600 MHz before set_mode completes,
gating DTBCLK causes the DP2 sink to lose its clock source.
2. The existing DTBCLK gating sequence ungates DTBCLK based on both pix_clk and ref_dtbclk,
but gates DTBCLK when either pix_clk or ref_dtbclk is zero.
pix_clk can be zero outside the set_mode sequence before DTBCLK is properly latched,
which can lead to DTBCLK being gated by mistake.
[how]
Consider both pixel_clk and ref_dtbclk when determining when it is safe to gate DTBCLK;
this is more accurate.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4701
Fixes: 5949e7c489 ("drm/amd/display: Enable Dynamic DTBCLK Switch")
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d04eb0c402780ca037b62a6aecf23b863545ebca)
Cc: stable@vger.kernel.org
KVM/arm64 fixes for 6.18, take #3
- Only adjust the ID registers when no irqchip has been created once
per VM run, instead of doing it once per vcpu, as this otherwise
triggers a pretty bad conbsistency check failure in the sysreg code.
- Make sure the per-vcpu Fine Grain Traps are computed before we load
the system registers on the HW, as we otherwise start running without
anything set until the first preemption of the vcpu.
The recent fix to properly initialize the tags of the huge zero folio
had an unfortunate not-so-subtle side effect: it caused the actual
*contents* of the huge zero folio to not be initialized at all when the
hardware didn't support the memory tagging.
The reason was the unfortunate semantics of tag_clear_highpage(): on
hardware that didn't do the tagging, it would silently just not do
anything at all. And since this is done only on arm64 with MTE support,
that basically meant most hardware.
It wasn't necessarily immediately obvious since the huge zero page isn't
necessarily very heavily used - or because it might already be zero
because all-zeroes is the most common pattern. But it ends up causing
random odd user space failures when you do hit it.
The unfortunate semantics have been around for a while, but became a
real bug only when we started actively using __GFP_ZEROTAGS in the
generic get_huge_zero_folio() function - before that, it had only ever
been used in code that checked that the hardware supported it.
Fix this by simply changing the semantics of tag_clear_highpage() to
return whether it actually successfully did something or not. While at
it, also make it initialize multiple pages in one go, since that's
actually what the only caller wants it to do and it simplifies the whole
logic.
Fixes: adfb6609c6 ("mm/huge_memory: initialise the tags of the huge zero folio")
Link: https://lore.kernel.org/all/20251117082023.90176-1-00107082@163.com/
Reviewed-by: David Hildenbrand (Red Hat) <david@kernel.org>
Reported-and-tested-by: David Wang <00107082@163.com>
Reported-and-tested-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Runtime PM should only be enabled in device_resume_early() if it has
been disabled for the given device by device_suspend_late(). Otherwise,
it may cause runtime PM callbacks to run prematurely in some cases
which leads to further functional issues.
Make two changes to address this problem.
First, reorder device_suspend_late() to only disable runtime PM for a
device when it is going to look for the device's callback or if the
device is a "syscore" one. In all of the other cases, disabling runtime
PM for the device is not in fact necessary. However, if the device's
callback returns an error and the power.is_late_suspended flag is not
going to be set, enable runtime PM so it only remains disabled when
power.is_late_suspended is set.
Second, make device_resume_early() only enable runtime PM for the
devices with the power.is_late_suspended flag set.
Fixes: 443046d1ad ("PM: sleep: Make suspend of devices more asynchronous")
Reported-by: Rose Wu <ya-jou.wu@mediatek.com>
Closes: https://lore.kernel.org/linux-pm/70b25dca6f8c2756d78f076f4a7dee7edaaffc33.camel@mediatek.com/
Cc: 6.16+ <stable@vger.kernel.org> # 6.16+
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/12784270.O9o76ZdvQC@rafael.j.wysocki
On PTL, no combo PHY is connected to PORT B. However, PORT B can
still be used for Type-C and will utilize the C20 PHY for eDP
over Type-C. In such configurations, VBTs also enumerate PORT B.
This leads to issues where PORT B is incorrectly identified as using the
C10 PHY, due to the assumption that returning true for PORT B in
intel_encoder_is_c10phy() would not cause problems.
From PTL's perspective, only PORT A/PHY A uses the C10 PHY.
Update the helper intel_encoder_is_c10phy() to return true only for
PORT A/PHY on PTL.
v2: Change the condition code style for ptl/wcl
Bspec: 72571,73944
Fixes: 9d10de78a3 ("drm/i915/wcl: C10 phy connected to port A and B")
Signed-off-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20250922150317.2334680-4-dnyaneshwar.bhadane@intel.com
(cherry picked from commit 8147f7a1c083fd565fb958824f7c552de3b2dc46)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We will need to differentiate between WCL and PTL in
intel_encoder_is_c10phy(). Since WCL and PTL use the same display
architecture, let's define WCL as a subplatform of PTL to allow the
differentiation.
v2: Update commit message and reorder wcl define (Gustavo)
Fixes: 3c0f211bc8 ("drm/xe: Add Wildcat Lake device IDs to PTL list")
Signed-off-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20250922150317.2334680-3-dnyaneshwar.bhadane@intel.com
(cherry picked from commit 4dfaae643e59cf3ab71b88689dce1b874f036f00)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Rodrigo added Fixes tag when porting it to fixes]
To form the WCL platform as a subplatform of PTL in definition,
WCL pci ids are splited into saparate group from PTL.
So update the pciidlist struct to cover all the pci ids.
v2:
- Squash wcl description in single patch for display and xe.(jani,gustavo)
Fixes: 3c0f211bc8 ("drm/xe: Add Wildcat Lake device IDs to PTL list")
Signed-off-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20250922150317.2334680-2-dnyaneshwar.bhadane@intel.com
(cherry picked from commit 32620e176443bf23ec81bfe8f177c6721a904864)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Rodrigo added the Fixes tag when porting it to fixes]
Handle skb allocation failures in RX path, to avoid NULL pointer
dereference and RX stalls under memory pressure. If the refill fails
with -ENOMEM, complete napi polling and wake up later to retry via timer.
Also explicitly re-enable RX DMA after oom, so the dmac doesn't remain
stopped in this situation.
Previously, memory pressure could lead to skb allocation failures and
subsequent Oops like:
Oops: Kernel access of bad area, sig: 11 [#2]
Hardware name: SonyPS3 Cell Broadband Engine 0x701000 PS3
NIP [c0003d0000065900] gelic_net_poll+0x6c/0x2d0 [ps3_gelic] (unreliable)
LR [c0003d00000659c4] gelic_net_poll+0x130/0x2d0 [ps3_gelic]
Call Trace:
gelic_net_poll+0x130/0x2d0 [ps3_gelic] (unreliable)
__napi_poll+0x44/0x168
net_rx_action+0x178/0x290
Steps to reproduce the issue:
1. Start a continuous network traffic, like scp of a 20GB file
2. Inject failslab errors using the kernel fault injection:
echo -1 > /sys/kernel/debug/failslab/times
echo 30 > /sys/kernel/debug/failslab/interval
echo 100 > /sys/kernel/debug/failslab/probability
3. After some time, traces start to appear, kernel Oopses
and the system stops
Step 2 is not always necessary, as it is usually already triggered by
the transfer of a big enough file.
Fixes: 02c1889166 ("ps3: gigabit ethernet driver for PS3, take3")
Signed-off-by: Florian Fuchs <fuchsfl@gmail.com>
Link: https://patch.msgid.link/20251113181000.3914980-1-fuchsfl@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The loops in 'qede_tpa_cont()' and 'qede_tpa_end()', iterate
over 'cqe->len_list[]' using only a zero-length terminator as
the stopping condition. If the terminator was missing or
malformed, the loop could run past the end of the fixed-size array.
Add an explicit bound check using ARRAY_SIZE() in both loops to prevent
a potential out-of-bounds access.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 55482edc25 ("qede: Add slowpath/fastpath support and enable hardware GRO")
Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com>
Link: https://patch.msgid.link/20251113112757.4166625-1-Pavel.Zhigulin@kaspersky.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In file uncore-frequency/uncore-frequency-common.h,
correct all kernel-doc warnings by adding missing leading " *" to some
lines, adding a missing kernel-doc entry, and fixing a name typo.
Warning: uncore-frequency-common.h:50 bad line:
Storage for kobject attribute elc_low_threshold_percent
Warning: uncore-frequency-common.h:52 bad line:
Storage for kobject attribute elc_high_threshold_percent
Warning: uncore-frequency-common.h:54 bad line:
Storage for kobject attribute elc_high_threshold_enable
Warning: uncore-frequency-common.h:92 struct member
'min_freq_khz_kobj_attr' not described in 'uncore_data'
Warning: uncore-frequency-common.h:92 struct member
'die_id_kobj_attr' not described in 'uncore_data'
Fixes: 24b6616355 ("platform/x86/intel-uncore-freq: Add efficiency latency control to sysfs interface")
Fixes: 416de0246f ("platform/x86: intel-uncore-freq: Fix types in sysfs callbacks")
Fixes: 247b43fcd8 ("platform/x86/intel-uncore-freq: Add attributes to show die_id")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20251111060938.1998542-1-rdunlap@infradead.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
isst_if_probe() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The return code is returned from the probe function as is but
probe functions should return normal errnos. A proper implementation
can be found in drivers/leds/leds-ss4200.c.
Convert PCIBIOS_* return codes using pcibios_err_to_errno() into
normal errno before returning.
Fixes: d3a2358429 ("platform/x86: ISST: Add Intel Speed Select mmio interface")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20251117033354.132-1-vulab@iscas.ac.cn
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
And expand it to encompass all pressure pads.
Definition: "pressure pad" as used here as includes all touchpads that
use physical pressure to convert to click, without physical hinges. Also
called haptic touchpads in general parlance, Synaptics calls them
ForcePads.
Most (all?) pressure pads are currently advertised as
INPUT_PROP_BUTTONPAD. The suggestion to identify them as pressure pads
by defining the resolution on ABS_MT_PRESSURE has been in the docs since
commit 20ccc8dd38 ("Documentation: input: define
ABS_PRESSURE/ABS_MT_PRESSURE resolution as grams") but few devices
provide this information.
In userspace it's thus impossible to determine whether a device is a
true pressure pad (pressure equals pressure) or a normal clickpad with
(pressure equals finger size).
Commit 7075ae4ac9 ("Input: add INPUT_PROP_HAPTIC_TOUCHPAD") introduces
INPUT_PROP_HAPTIC_TOUCHPAD but restricted it to those touchpads that
have support for userspace-controlled effects. Let's expand and rename
that definition to include all pressure pad touchpads since those that
do support FF effects can be identified by the presence of the
FF_HAPTIC bit.
This means:
- clickpad: INPUT_PROP_BUTTONPAD
- pressurepad: INPUT_PROP_BUTTONPAD + INPUT_PROP_PRESSUREPAD
- pressurepad with configurable haptics:
INPUT_PROP_BUTTONPAD + INPUT_PROP_PRESSUREPAD + FF_HAPTIC
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://patch.msgid.link/20251106114534.GA405512@tassie
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Airoha_eth driver forwards offloaded uplink traffic (packets received
on GDM1 and forwarded to GDM{3,4}) to GDM2 in order to apply hw QoS.
This is correct if the device does not support a dedicated GDM2 port.
In this case, in order to enable hw offloading for uplink traffic,
the packets should be sent to GDM{3,4} directly.
Fixes: 9cd451d414 ("net: airoha: Add loopback support for GDM2")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20251113-airoha-hw-offload-gdm2-fix-v1-1-7e4ca300872f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ret_set_ksft_status() calls ksft_status_merge() with the current return
status and the last one. It treats a non-zero return code from
ksft_status_merge() as an indication that the return status was
overwritten by the last one and therefore overwrites the return message
with the last one.
Currently, ksft_status_merge() returns a non-zero return code even if
the current return status and the last one are equal. This results in
return messages being overwritten which is counter-productive since we
are more interested in the first failure message and not the last one.
Fix by changing ksft_status_merge() to only return a non-zero return
code if the current return status was actually changed.
Add a test case which checks that the first error message is not
overwritten.
Before:
# ./lib_sh_test.sh
[...]
TEST: RET tfail2 tfail -> fail [FAIL]
retmsg=tfail expected tfail2
[...]
# echo $?
1
After:
# ./lib_sh_test.sh
[...]
TEST: RET tfail2 tfail -> fail [ OK ]
[...]
# echo $?
0
Fixes: 596c8819cb ("selftests: forwarding: Have RET track kselftest framework constants")
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20251116081029.69112-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function 'mpc_rcvd_sweep_req(mpcginfo)' is called conditionally
from function 'ctcmpc_unpack_skb'. It frees passed mpcginfo.
After that a call to function 'kfree' in function 'ctcmpc_unpack_skb'
frees it again.
Remove 'kfree' call in function 'mpc_rcvd_sweep_req(mpcginfo)'.
Bug detected by the clang static analyzer.
Fixes: 0c0b20587b ("s390/ctcm: fix potential memory leak")
Reviewed-by: Aswin Karuvally <aswin@linux.ibm.com>
Signed-off-by: Aleksei Nikiforov <aleksei.nikiforov@linux.ibm.com>
Signed-off-by: Aswin Karuvally <aswin@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251112182724.1109474-1-aswin@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull vfs fixes from Christian Brauner:
- Fix unitialized variable in statmount_string()
- Fix hostfs mounting when passing host root during boot
- Fix dynamic lookup to fail on cell lookup failure
- Fix missing file type when reading bfs inodes from disk
- Enforce checking of sb_min_blocksize() calls and update all callers
accordingly
- Restore write access before closing files opened by open_exec() in
binfmt_misc
- Always freeze efivarfs during suspend/hibernate cycles
- Fix statmount()'s and listmount()'s grab_requested_mnt_ns() helper to
actually allow mount namespace file descriptor in addition to mount
namespace ids
- Fix tmpfs remount when noswap is specified
- Switch Landlock to iput_not_last() to remove false-positives from
might_sleep() annotations in iput()
- Remove dead node_to_mnt_ns() code
- Ensure that per-queue kobjects are successfully created
* tag 'vfs-6.18-rc7.fixes' of gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs:
landlock: fix splats from iput() after it started calling might_sleep()
fs: add iput_not_last()
shmem: fix tmpfs reconfiguration (remount) when noswap is set
fs/namespace: correctly handle errors returned by grab_requested_mnt_ns
power: always freeze efivarfs
binfmt_misc: restore write access before closing files opened by open_exec()
block: add __must_check attribute to sb_min_blocksize()
virtio-fs: fix incorrect check for fsvq->kobj
xfs: check the return value of sb_min_blocksize() in xfs_fs_fill_super
isofs: check the return value of sb_min_blocksize() in isofs_fill_super
exfat: check return value of sb_min_blocksize in exfat_read_boot_sector
vfat: fix missing sb_min_blocksize() return value checks
mnt: Remove dead code which might prevent from building
bfs: Reconstruct file type when loading from disk
afs: Fix dynamic lookup to fail on cell lookup failure
hostfs: Fix only passing host root in boot stage with new mount
fs: Fix uninitialized 'offp' in statmount_string()
Pull sched_ext fixes from Tejun Heo:
"Five fixes addressing PREEMPT_RT compatibility and locking issues.
Three commits fix potential deadlocks and sleeps in atomic contexts on
RT kernels by converting locks to raw spinlocks and ensuring IRQ work
runs in hard-irq context. The remaining two fix unsafe locking in the
debug dump path and a variable dereference typo"
* tag 'sched_ext-for-6.18-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
sched_ext: Use IRQ_WORK_INIT_HARD() to initialize rq->scx.kick_cpus_irq_work
sched_ext: Fix possible deadlock in the deferred_irq_workfn()
sched/ext: convert scx_tasks_lock to raw spinlock
sched_ext: Fix unsafe locking in the scx_dump_state()
sched_ext: Fix use of uninitialized variable in scx_bpf_cpuperf_set()
Now target is removed from nvme_fc_ctrl_free() which is the ctrl->ref
release handler. And even admin queue is unquiesced there, this way
is definitely wrong because the ctr->ref is grabbed when submitting
command.
And Marco observed that nvme_fc_ctrl_free() can be called from request
completion code path, and trigger kernel warning since request completes
from softirq context.
Fix the issue by moveing target removal into nvme_fc_delete_ctrl(),
which is also aligned with nvme-tcp and nvme-rdma.
Patch originally proposed by Ming Lei, then modified to move the tagset
removal down to after nvme_fc_delete_association() after further testing.
Cc: Marco Patalano <mpatalan@redhat.com>
Cc: Ewan Milne <emilne@redhat.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Cc: stable@vger.kernel.org
Tested-by: Marco Patalano <mpatalan@redhat.com>
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Pull MTD fixes from Miquel Raynal:
"Mostly small misc fixes, here they are sorted by sub-subsystem:
ECC fixes:
- Realtek Kconfig fix
SPI NAND fixes:
- Remove nonexistent QE bit on FMSH FM25S01A
Raw NAND fixes:
- Prevent DMA device NULL pointer dereference in Cadence driver
MTD device fixes:
- Possible integer overflow in read/write ioctls
- Fix the IRQ handler pointer in the onenand driver, even if in
practice it is never dereferenced.
* tag 'mtd/fixes-for-6.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: onenand: Pass correct pointer to IRQ handler
mtd: spinand: fmsh: remove QE bit for FM25S01A flash
mtd: rawnand: cadence: fix DMA device NULL pointer dereference
mtd: rawnand: realtek: Make rtl_ecc_engine_ops const
mtd: nand: MTD_NAND_ECC_REALTEK should depend on HAS_DMA
mtd: nand: realtek-ecc: Fix a IS_ERR() vs NULL bug in probe
mtdchar: fix integer overflow in read/write ioctls
Commit 7e091add9c "nvme-auth: update sc_c in host response" added
the sc_c variable to the dhchap queue context structure which is
appropriately set during negotiate and then used in the host response.
This breaks secure concat connections with a Linux target as the target
code wasn't updated at the same time. This patch fixes this by adding a
new sc_c variable to the host hash calculations.
Fixes: 7e091add9c ("nvme-auth: update sc_c in host response")
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Martin George <marting@netapp.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
For PREEMPT_RT kernels, the kick_cpus_irq_workfn() be invoked in
the per-cpu irq_work/* task context and there is no rcu-read critical
section to protect. this commit therefore use IRQ_WORK_INIT_HARD() to
initialize the per-cpu rq->scx.kick_cpus_irq_work in the
init_sched_ext_class().
Signed-off-by: Zqiang <qiang.zhang@linux.dev>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix writing bpf_prog (infos|btfs)_cnt to data file, to not generate
invalid perf.data files in some corner cases.
- Fix 'perf top' segfault by ensuring libbfd is initialized. This is an
opt-in feature due to license incompatibilities.
- Fix segfault in 'perf lock' due to missing kernel map.
- Fix 'perf lock contention' test.
- Don't fail fast path detection if binutils-devel isn't available.
- Sync KVM's vmx.h with the kernel to pick SEAMCALL exit reason.
* tag 'perf-tools-fixes-for-v6.18-2-2025-11-16' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
perf libbfd: Ensure libbfd is initialized prior to use
perf test: Fix lock contention test
perf lock: Fix segfault due to missing kernel map
tools headers UAPI: Sync KVM's vmx.h with the kernel to pick SEAMCALL exit reason
perf build: Don't fail fast path feature detection when binutils-devel is not available
perf header: Write bpf_prog (infos|btfs)_cnt to data file
Pull misc fixes from Andrew Morton:
"7 hotfixes. 5 are cc:stable, 4 are against mm/
All are singletons - please see the respective changelogs for details"
* tag 'mm-hotfixes-stable-2025-11-16-10-40' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm, swap: fix potential UAF issue for VMA readahead
selftests/user_events: fix type cast for write_index packed member in perf_test
lib/test_kho: check if KHO is enabled
mm/huge_memory: fix folio split check for anon folios in swapcache
MAINTAINERS: update David Hildenbrand's email address
crash: fix crashkernel resource shrink
mm: fix MAX_FOLIO_ORDER on powerpc configs with hugetlb
The file tools/arch/riscv/include/asm/csr.h borrows from
arch/riscv/include/asm/csr.h, and subsequent modifications
related to CSR should maintain consistency.
Signed-off-by: Chen Pei <cp0613@linux.alibaba.com>
Link: https://patch.msgid.link/20251114071215.816-1-cp0613@linux.alibaba.com
[pjw@kernel.org: dropped Fixes: lines for patches that weren't broken; removed superfluous blank line]
Signed-off-by: Paul Walmsley <pjw@kernel.org>
Currently, the sbi_init() always attempts to register the legacy shutdown
function as the sys-off handler which is fine when RISCV_SBI_V01 is not
enabled. However, if RISCV_SBI_V01 is enabled in the kernel and the SBI
v0.1 is not supported by the underlying SBI implementation then the
legacy shutdown fails. Fix this by not registering the legacy shutdown
when SRST shutdown is available.
Fixes: 70ddf86d76 ("riscv: sbi: Switch to new sys-off handler API")
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://patch.msgid.link/20251114065808.304430-1-mchitale@ventanamicro.com
Signed-off-by: Paul Walmsley <pjw@kernel.org>
Pull firewire fixes from Takashi Sakamoto:
"This includes some fixes for the topology map, newly introduced in
v6.18 kernel"
* tag 'firewire-fixes-6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: core: fix to update generation field in topology map
firewire: core: Initialize topology_map.lock
Pull EDAC fixes from Borislav Petkov:
- In Versalnet, handle the reporting of non-standard hw errors whose
information can come in more than one remote processor message.
- Explicitly reenable ECC checking after a warm reset in Altera OCRAM
as those registers are reset to default otherwise
- Fix single-bit error injection in Altera EDAC to not inject errors
directly in ECC RAM and thus lead to false double-bit errors due to
same ECC RAM being in concurrent use
* tag 'edac_urgent_for_v6.18_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/altera: Use INTTEST register for Ethernet and USB SBE injection
EDAC/altera: Handle OCRAM ECC enable after warm reset
EDAC/versalnet: Handle split messages for non-standard errors
Since commit 78524b05f1 ("mm, swap: avoid redundant swap device
pinning"), the common helper for allocating and preparing a folio in the
swap cache layer no longer tries to get a swap device reference
internally, because all callers of __read_swap_cache_async are already
holding a swap entry reference. The repeated swap device pinning isn't
needed on the same swap device.
Caller of VMA readahead is also holding a reference to the target entry's
swap device, but VMA readahead walks the page table, so it might encounter
swap entries from other devices, and call __read_swap_cache_async on
another device without holding a reference to it.
So it is possible to cause a UAF when swapoff of device A raced with
swapin on device B, and VMA readahead tries to read swap entries from
device A. It's not easy to trigger, but in theory, it could cause real
issues.
Make VMA readahead try to get the device reference first if the swap
device is a different one from the target entry.
Link: https://lkml.kernel.org/r/20251111-swap-fix-vma-uaf-v1-1-41c660e58562@tencent.com
Fixes: 78524b05f1 ("mm, swap: avoid redundant swap device pinning")
Suggested-by: Huang Ying <ying.huang@linux.alibaba.com>
Signed-off-by: Kairui Song <kasong@tencent.com>
Acked-by: Chris Li <chrisl@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Kemeng Shi <shikemeng@huaweicloud.com>
Cc: Nhat Pham <nphamcs@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When crashkernel is configured with a high reservation, shrinking its
value below the low crashkernel reservation causes two issues:
1. Invalid crashkernel resource objects
2. Kernel crash if crashkernel shrinking is done twice
For example, with crashkernel=200M,high, the kernel reserves 200MB of high
memory and some default low memory (say 256MB). The reservation appears
as:
cat /proc/iomem | grep -i crash
af000000-beffffff : Crash kernel
433000000-43f7fffff : Crash kernel
If crashkernel is then shrunk to 50MB (echo 52428800 >
/sys/kernel/kexec_crash_size), /proc/iomem still shows 256MB reserved:
af000000-beffffff : Crash kernel
Instead, it should show 50MB:
af000000-b21fffff : Crash kernel
Further shrinking crashkernel to 40MB causes a kernel crash with the
following trace (x86):
BUG: kernel NULL pointer dereference, address: 0000000000000038
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
<snip...>
Call Trace: <TASK>
? __die_body.cold+0x19/0x27
? page_fault_oops+0x15a/0x2f0
? search_module_extables+0x19/0x60
? search_bpf_extables+0x5f/0x80
? exc_page_fault+0x7e/0x180
? asm_exc_page_fault+0x26/0x30
? __release_resource+0xd/0xb0
release_resource+0x26/0x40
__crash_shrink_memory+0xe5/0x110
crash_shrink_memory+0x12a/0x190
kexec_crash_size_store+0x41/0x80
kernfs_fop_write_iter+0x141/0x1f0
vfs_write+0x294/0x460
ksys_write+0x6d/0xf0
<snip...>
This happens because __crash_shrink_memory()/kernel/crash_core.c
incorrectly updates the crashk_res resource object even when
crashk_low_res should be updated.
Fix this by ensuring the correct crashkernel resource object is updated
when shrinking crashkernel memory.
Link: https://lkml.kernel.org/r/20251101193741.289252-1-sourabhjain@linux.ibm.com
Fixes: 16c6006af4 ("kexec: enable kexec_crash_size to support two crash kernel regions")
Signed-off-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Zhen Lei <thunder.leizhen@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In the past, CONFIG_ARCH_HAS_GIGANTIC_PAGE indicated that we support
runtime allocation of gigantic hugetlb folios. In the meantime it evolved
into a generic way for the architecture to state that it supports gigantic
hugetlb folios.
In commit fae7d834c4 ("mm: add __dump_folio()") we started using
CONFIG_ARCH_HAS_GIGANTIC_PAGE to decide MAX_FOLIO_ORDER: whether we could
have folios larger than what the buddy can handle. In the context of that
commit, we started using MAX_FOLIO_ORDER to detect page corruptions when
dumping tail pages of folios. Before that commit, we assumed that we
cannot have folios larger than the highest buddy order, which was
obviously wrong.
In commit 7b4f21f5e0 ("mm/hugetlb: check for unreasonable folio sizes
when registering hstate"), we used MAX_FOLIO_ORDER to detect
inconsistencies, and in fact, we found some now.
Powerpc allows for configs that can allocate gigantic folio during boot
(not at runtime), that do not set CONFIG_ARCH_HAS_GIGANTIC_PAGE and can
exceed PUD_ORDER.
To fix it, let's make powerpc select CONFIG_ARCH_HAS_GIGANTIC_PAGE with
hugetlb on powerpc, and increase the maximum folio size with hugetlb to 16
GiB on 64bit (possible on arm64 and powerpc) and 1 GiB on 32 bit
(powerpc). Note that on some powerpc configurations, whether we actually
have gigantic pages depends on the setting of CONFIG_ARCH_FORCE_MAX_ORDER,
but there is nothing really problematic about setting it unconditionally:
we just try to keep the value small so we can better detect problems in
__dump_folio() and inconsistencies around the expected largest folio in
the system.
Ideally, we'd have a better way to obtain the maximum hugetlb folio size
and detect ourselves whether we really end up with gigantic folios. Let's
defer bigger changes and fix the warnings first.
While at it, handle gigantic DAX folios more clearly: DAX can only end up
creating gigantic folios with HAVE_ARCH_TRANSPARENT_HUGEPAGE_PUD.
Add a new Kconfig option HAVE_GIGANTIC_FOLIOS to make both cases clearer.
In particular, worry about ARCH_HAS_GIGANTIC_PAGE only with HUGETLB_PAGE.
Note: with enabling CONFIG_ARCH_HAS_GIGANTIC_PAGE on powerpc, we will now
also allow for runtime allocations of folios in some more powerpc configs.
I don't think this is a problem, but if it is we could handle it through
__HAVE_ARCH_GIGANTIC_PAGE_RUNTIME_SUPPORTED.
While __dump_page()/__dump_folio was also problematic (not handling
dumping of tail pages of such gigantic folios correctly), it doesn't seem
critical enough to mark it as a fix.
Link: https://lkml.kernel.org/r/20251114214920.2550676-1-david@kernel.org
Fixes: 7b4f21f5e0 ("mm/hugetlb: check for unreasonable folio sizes when registering hstate")
Reported-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Closes: https://lore.kernel.org/r/3e043453-3f27-48ad-b987-cc39f523060a@csgroup.eu/
Reported-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Closes: https://lore.kernel.org/r/94377f5c-d4f0-4c0f-b0f6-5bf1cd7305b1@linux.ibm.com/
Signed-off-by: David Hildenbrand (Red Hat) <david@kernel.org>
Cc: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Donet Tom <donettom@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: "Liam R. Howlett" <Liam.Howlett@oracle.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Pull s390 fix from Heiko Carstens:
- Fix a bug in the __ptep_rdp() inline assembly which may lead to
missing TLB flushes
* tag 's390-6.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: Fix __ptep_rdp() inline assembly
Pull x86 fixes from Ingo Molnar:
- Update the list of AMD microcode minimum Entrysign revisions
- Add additional fixed AMD RDSEED microcode revisions
- Update the language transliteration for Kiryl Shutsemau's name
in the MAINTAINERS entry
* tag 'x86-urgent-2025-11-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode/AMD: Add Zen5 model 0x44, stepping 0x1 minrev
x86/CPU/AMD: Add additional fixed RDSEED microcode revisions
MAINTAINERS: Update name spelling
Pull timer fix from Ingo Molnar:
"Fix a memory leak in the posix timer creation logic"
* tag 'timers-urgent-2025-11-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-timers: Plug potential memory leak in do_timer_create()
Pull irq fix from Ingo Molnar:
"Fix an irqchip driver release bug in the riscv-intc irqchip driver"
* tag 'irq-urgent-2025-11-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/riscv-intc: Add missing free() callback in riscv_intc_domain_ops
Pull core fix from Ingo Molnar:
"Fix a broken #ifndef in the <linux/entry-virt.h> header.
It hasn't caused problems upstream yet because no arch overrides
arch_xfer_to_guest_mode_handle_work() at this moment"
* tag 'core-urgent-2025-11-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
entry: Fix ifndef around arch_xfer_to_guest_mode_handle_work() stub
Commit dc82a33297 ("veth: apply qdisc backpressure on full ptr_ring to
reduce TX drops") introduced a race condition that can lead to a permanently
stalled TXQ. This was observed in production on ARM64 systems (Ampere Altra
Max).
The race occurs in veth_xmit(). The producer observes a full ptr_ring and
stops the queue (netif_tx_stop_queue()). The subsequent conditional logic,
intended to re-wake the queue if the consumer had just emptied it (if
(__ptr_ring_empty(...)) netif_tx_wake_queue()), can fail. This leads to a
"lost wakeup" where the TXQ remains stopped (QUEUE_STATE_DRV_XOFF) and
traffic halts.
This failure is caused by an incorrect use of the __ptr_ring_empty() API
from the producer side. As noted in kernel comments, this check is not
guaranteed to be correct if a consumer is operating on another CPU. The
empty test is based on ptr_ring->consumer_head, making it reliable only for
the consumer. Using this check from the producer side is fundamentally racy.
This patch fixes the race by adopting the more robust logic from an earlier
version V4 of the patchset, which always flushed the peer:
(1) In veth_xmit(), the racy conditional wake-up logic and its memory barrier
are removed. Instead, after stopping the queue, we unconditionally call
__veth_xdp_flush(rq). This guarantees that the NAPI consumer is scheduled,
making it solely responsible for re-waking the TXQ.
This handles the race where veth_poll() consumes all packets and completes
NAPI *before* veth_xmit() on the producer side has called netif_tx_stop_queue.
The __veth_xdp_flush(rq) will observe rx_notify_masked is false and schedule
NAPI.
(2) On the consumer side, the logic for waking the peer TXQ is moved out of
veth_xdp_rcv() and placed at the end of the veth_poll() function. This
placement is part of fixing the race, as the netif_tx_queue_stopped() check
must occur after rx_notify_masked is potentially set to false during NAPI
completion.
This handles the race where veth_poll() consumes all packets, but haven't
finished (rx_notify_masked is still true). The producer veth_xmit() stops the
TXQ and __veth_xdp_flush(rq) will observe rx_notify_masked is true, meaning
not starting NAPI. Then veth_poll() change rx_notify_masked to false and
stops NAPI. Before exiting veth_poll() will observe TXQ is stopped and wake
it up.
Fixes: dc82a33297 ("veth: apply qdisc backpressure on full ptr_ring to reduce TX drops")
Reviewed-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://patch.msgid.link/176295323282.307447.14790015927673763094.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The validation of the set(nsh(...)) action is completely wrong.
It runs through the nsh_key_put_from_nlattr() function that is the
same function that validates NSH keys for the flow match and the
push_nsh() action. However, the set(nsh(...)) has a very different
memory layout. Nested attributes in there are doubled in size in
case of the masked set(). That makes proper validation impossible.
There is also confusion in the code between the 'masked' flag, that
says that the nested attributes are doubled in size containing both
the value and the mask, and the 'is_mask' that says that the value
we're parsing is the mask. This is causing kernel crash on trying to
write into mask part of the match with SW_FLOW_KEY_PUT() during
validation, while validate_nsh() doesn't allocate any memory for it:
BUG: kernel NULL pointer dereference, address: 0000000000000018
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 1c2383067 P4D 1c2383067 PUD 20b703067 PMD 0
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 8 UID: 0 Kdump: loaded Not tainted 6.17.0-rc4+ #107 PREEMPT(voluntary)
RIP: 0010:nsh_key_put_from_nlattr+0x19d/0x610 [openvswitch]
Call Trace:
<TASK>
validate_nsh+0x60/0x90 [openvswitch]
validate_set.constprop.0+0x270/0x3c0 [openvswitch]
__ovs_nla_copy_actions+0x477/0x860 [openvswitch]
ovs_nla_copy_actions+0x8d/0x100 [openvswitch]
ovs_packet_cmd_execute+0x1cc/0x310 [openvswitch]
genl_family_rcv_msg_doit+0xdb/0x130
genl_family_rcv_msg+0x14b/0x220
genl_rcv_msg+0x47/0xa0
netlink_rcv_skb+0x53/0x100
genl_rcv+0x24/0x40
netlink_unicast+0x280/0x3b0
netlink_sendmsg+0x1f7/0x430
____sys_sendmsg+0x36b/0x3a0
___sys_sendmsg+0x87/0xd0
__sys_sendmsg+0x6d/0xd0
do_syscall_64+0x7b/0x2c0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
The third issue with this process is that while trying to convert
the non-masked set into masked one, validate_set() copies and doubles
the size of the OVS_KEY_ATTR_NSH as if it didn't have any nested
attributes. It should be copying each nested attribute and doubling
them in size independently. And the process must be properly reversed
during the conversion back from masked to a non-masked variant during
the flow dump.
In the end, the only two outcomes of trying to use this action are
either validation failure or a kernel crash. And if somehow someone
manages to install a flow with such an action, it will most definitely
not do what it is supposed to, since all the keys and the masks are
mixed up.
Fixing all the issues is a complex task as it requires re-writing
most of the validation code.
Given that and the fact that this functionality never worked since
introduction, let's just remove it altogether. It's better to
re-introduce it later with a proper implementation instead of trying
to fix it in stable releases.
Fixes: b2d0f5d5dc ("openvswitch: enable NSH support")
Reported-by: Junvy Yang <zhuque@tencent.com>
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20251112112246.95064-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzbot reported use-after-free in mptcp_schedule_work() [1]
Issue here is that mptcp_schedule_work() schedules a work,
then gets a refcount on sk->sk_refcnt if the work was scheduled.
This refcount will be released by mptcp_worker().
[A] if (schedule_work(...)) {
[B] sock_hold(sk);
return true;
}
Problem is that mptcp_worker() can run immediately and complete before [B]
We need instead :
sock_hold(sk);
if (schedule_work(...))
return true;
sock_put(sk);
[1]
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 1 PID: 29 at lib/refcount.c:25 refcount_warn_saturate+0xfa/0x1d0 lib/refcount.c:25
Call Trace:
<TASK>
__refcount_add include/linux/refcount.h:-1 [inline]
__refcount_inc include/linux/refcount.h:366 [inline]
refcount_inc include/linux/refcount.h:383 [inline]
sock_hold include/net/sock.h:816 [inline]
mptcp_schedule_work+0x164/0x1a0 net/mptcp/protocol.c:943
mptcp_tout_timer+0x21/0xa0 net/mptcp/protocol.c:2316
call_timer_fn+0x17e/0x5f0 kernel/time/timer.c:1747
expire_timers kernel/time/timer.c:1798 [inline]
__run_timers kernel/time/timer.c:2372 [inline]
__run_timer_base+0x648/0x970 kernel/time/timer.c:2384
run_timer_base kernel/time/timer.c:2393 [inline]
run_timer_softirq+0xb7/0x180 kernel/time/timer.c:2403
handle_softirqs+0x22f/0x710 kernel/softirq.c:622
__do_softirq kernel/softirq.c:656 [inline]
run_ktimerd+0xcf/0x190 kernel/softirq.c:1138
smpboot_thread_fn+0x542/0xa60 kernel/smpboot.c:160
kthread+0x711/0x8a0 kernel/kthread.c:463
ret_from_fork+0x4bc/0x870 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
Cc: stable@vger.kernel.org
Fixes: 3b1d6210a9 ("mptcp: implement and use MPTCP-level retransmission")
Reported-by: syzbot+355158e7e301548a1424@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/6915b46f.050a0220.3565dc.0028.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251113103924.3737425-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The LED setup routine registered both led_sync_good
and led_is_gm devices without checking the return
values of led_classdev_register(). If either registration
failed, the function continued silently, leaving the
driver in a partially-initialized state and leaking
a registered LED classdev.
Add proper error handling
Fixes: 7d9ee2e8ff ("net: dsa: hellcreek: Add PTP status LEDs")
Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://patch.msgid.link/20251113135745.92375-1-Pavel.Zhigulin@kaspersky.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull pci fixes from Bjorn Helgaas:
- Cache the ASPM L0s/L1 Supported bits early so quirks can override
them if necessary (Bjorn Helgaas)
- Add quirks for PA Semi and Freescale Root Ports and a HiSilicon Wi-Fi
device that are reported to have broken L0s and L1 (Shawn Lin, Bjorn
Helgaas)
* tag 'pci-v6.18-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/ASPM: Avoid L0s and L1 on Hi1105 [19e5:1105] Wi-Fi
PCI/ASPM: Avoid L0s and L1 on PA Semi [1959:a002] Root Ports
PCI/ASPM: Avoid L0s and L1 on Freescale [1957:0451] Root Ports
PCI/ASPM: Convert quirks to override advertised link states
PCI/ASPM: Add pcie_aspm_remove_cap() to override advertised link states
PCI/ASPM: Cache L0s/L1 Supported so advertised link states can be overridden
Pull bpf fixes from Alexei Starovoitov:
- Fix interaction between livepatch and BPF fexit programs (Song Liu)
With Steven and Masami acks.
- Fix stack ORC unwind from BPF kprobe_multi (Jiri Olsa)
With Steven and Masami acks.
- Fix out of bounds access in widen_imprecise_scalars() in the verifier
(Eduard Zingerman)
- Fix conflicts between MPTCP and BPF sockmap (Jiayuan Chen)
- Fix net_sched storage collision with BPF data_meta/data_end (Eric
Dumazet)
- Add _impl suffix to BPF kfuncs with implicit args to avoid breaking
them in bpf-next when KF_IMPLICIT_ARGS is added (Mykyta Yatsenko)
* tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: Test widen_imprecise_scalars() with different stack depth
bpf: account for current allocated stack depth in widen_imprecise_scalars()
bpf: Add bpf_prog_run_data_pointers()
selftests/bpf: Add mptcp test with sockmap
mptcp: Fix proto fallback detection with BPF
mptcp: Disallow MPTCP subflows from sockmap
selftests/bpf: Add stacktrace ips test for raw_tp
selftests/bpf: Add stacktrace ips test for kprobe_multi/kretprobe_multi
x86/fgraph,bpf: Fix stack ORC unwind from kprobe_multi return probe
Revert "perf/x86: Always store regs->ip in perf_callchain_kernel()"
bpf: add _impl suffix for bpf_stream_vprintk() kfunc
bpf:add _impl suffix for bpf_task_work_schedule* kfuncs
selftests/bpf: Add tests for livepatch + bpf trampoline
ftrace: bpf: Fix IPMODIFY + DIRECT in modify_ftrace_direct()
ftrace: Fix BPF fexit with livepatch
Pull Rust fix from Miguel Ojeda:
- Fix a Rust 1.91.0 build issue due to 'bindings.o' not containing
DWARF debug information anymore by teaching gendwarfksyms to skip
object files without exports
* tag 'rust-fixes-6.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux:
gendwarfksyms: Skip files with no exports
Pull NFS client fixes from Anna Schumaker:
- Various fixes when using NFS with TLS
- Localio direct-IO fixes
- Fix error handling in nfs_atomic_open_v23()
- Fix sysfs memory leak when nfs_client kobject add fails
- Fix an incorrect parameter when calling nfs4_call_sync()
- Fix a failing LTP test when using delegated timestamps
* tag 'nfs-for-6.18-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS: Fix LTP test failures when timestamps are delegated
NFSv4: Fix an incorrect parameter when calling nfs4_call_sync()
NFS: sysfs: fix leak when nfs_client kobject add fails
NFSv2/v3: Fix error handling in nfs_atomic_open_v23()
nfs/localio: do not issue misaligned DIO out-of-order
nfs/localio: Ensure DIO WRITE's IO on stable storage upon completion
nfs/localio: backfill missing partial read support for misaligned DIO
nfs/localio: add refcounting for each iocb IO associated with NFS pgio header
nfs/localio: remove unecessary ENOTBLK handling in DIO WRITE support
NFS: Check the TLS certificate fields in nfs_match_client()
pnfs: Set transport security policy to RPC_XPRTSEC_NONE unless using TLS
pnfs: Fix TLS logic in _nfs4_pnfs_v4_ds_connect()
pnfs: Fix TLS logic in _nfs4_pnfs_v3_ds_connect()
Pull drm fixes from Dave Airlie:
"Weekly fixes, amdgpu and vmwgfx making up the most of it, along with
panthor and i915/xe.
Seems about right for this time of development, nothing major
outstanding.
client:
- Fix description of module parameter
panthor:
- Flush writes before mapping buffers
vmwgfx:
- Improve command validation
- Improve ref counting
- Fix cursor-plane support
amdgpu:
- Disallow P2P DMA for GC 12 DCC surfaces
- ctx error handling fix
- UserQ fixes
- VRR fix
- ISP fix
- JPEG 5.0.1 fix
amdkfd:
- Save area check fix
- Fix GPU mappings for APU after prefetch
i915:
- Fix PSR's pipe to vblank conversion
- Disable Panel Replay on MST links
xe:
- New HW workarounds affecting PTL and WCL platforms
* tag 'drm-fixes-2025-11-15' of https://gitlab.freedesktop.org/drm/kernel:
drm/client: fix MODULE_PARM_DESC string for "active"
drm/i915/dp_mst: Disable Panel Replay
drm/amdkfd: Fix GPU mappings for APU after prefetch
drm/amdkfd: relax checks for over allocation of save area
drm/amdgpu/jpeg: Add parse_cs for JPEG5_0_1
drm/amd/amdgpu: Ensure isp_kernel_buffer_alloc() creates a new BO
drm/amd/display: Allow VRR params change if unsynced with the stream
drm/amdgpu: fix lock warning in amdgpu_userq_fence_driver_process
drm/amdgpu: jump to the correct label on failure
drm/amdgpu: disable peer-to-peer access for DCC-enabled GC12 VRAM surfaces
drm/xe/xe3lpg: Extend Wa_15016589081 for xe3lpg
drm/xe/xe3: Extend wa_14023061436
drm/xe/xe3: Add WA_14024681466 for Xe3_LPG
drm/i915/psr: fix pipe to vblank conversion
drm/panthor: Flush shmem writes before mapping buffers CPU-uncached
drm/vmwgfx: Restore Guest-Backed only cursor plane support
drm/vmwgfx: Use kref in vmw_bo_dirty
drm/vmwgfx: Validate command header size against SVGA_CMD_MAX_DATASIZE
TEE kernel-doc fixes for v6.18
* tag 'tee-fix-for-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jenswi/linux-tee:
tee: <uapi/linux/tee.h: fix all kernel-doc issues
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM64-based SoCs Device Tree fixes
for 6.18, please pull the following:
- Andrea assigns clocks rates for the Ethernet controller for the
Raspberry Pi 5 systems
- Laurent adds an ethernet0 alias to allow client programs consuming
that alias to populate the correct Ethernet address for the Raspberry
Pi 5 systems
* tag 'arm-soc/for-6.18/devicetree-arm64-fixes-v2' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: bcm2712: rpi-5: Add ethernet0 alias
arm64: dts: broadcom: Assign clock rates in eth node for RPi5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reset controller fixes for v6.18
* Fix incorrect EARC reset masks in the reset-imx8mp-audiomix driver,
introduced in commit a83bc87cd3.
* tag 'reset-fixes-for-v6.18' of https://git.pengutronix.de/git/pza/linux:
reset: imx8mp-audiomix: Fix bad mask values
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM-based SoCs Device Tree files updates
for 6.18, please pull the following:
- Rafal fixes the Ethernet PHY address on the Luxul XAP-1440
* tag 'arm-soc/for-6.18/devicetree-fixes-part2' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM53573: Fix address of Luxul XAP-1440's Ethernet PHY
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM64 defconfig updates for 6.18,
please pull the following:
- Stefan ensures that the clk-raspberrypi driver which is now the clock
provider is built into the kernel image to satisfy root over NFS
* tag 'arm-soc/for-6.18/defconfig-arm64-fixes' of https://github.com/Broadcom/stblinux:
arm64: defconfig: Fix V3D deferred probe timeout
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Memory controller drivers - fixes for v6.18
Correct incorrect ID used for the memory controller client IDs in
Tegra210 Memory Controller driver, introduced in v6.18-rc1.
* tag 'memory-controller-drv-fixes-6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: tegra210: Fix incorrect client ids
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull spi fixes from Mark Brown:
"A few standard fixes here, plus one more interesting one from Hans
which addresses an issue where a move in when we requested GPIOs on
ACPI systems caused us to stop doing pinmuxing and leave things
floating that we'd really rather not have floating"
* tag 'spi-fix-v6.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Add TODO comment about ACPI GPIO setup
spi: xilinx: increase number of retries before declaring stall
spi: imx: keep dma request disabled before dma transfer setup
spi: Try to get ACPI GPIO IRQ earlier
First batch of ASPEED fixes for 6.18
This time it's just the one fix addressing a PHY configuration regression in the
Fuji (Meta) platform's mac3 devicetree node.
* tag 'aspeed-6.18-fixes-0' of https://git.kernel.org/pub/scm/linux/kernel/git/bmc/linux:
ARM: dts: aspeed: fuji-data64: Enable mac3 controller
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arm64: tegra: Fixes for v6.18
This contains a simple fix to mark the Ethernet PHY on Jetson Xavier NX
as a wakeup source so the device can support WoL.
* tag 'tegra-for-6.18-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Mark Jetson Xavier NX's PHY as a wakeup source
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull regulator fix from Mark Brown:
"One simple fix for a GPIO descriptor leak in the probe error handling
for the fixed regulator"
* tag 'regulator-fix-v6.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fixed: fix GPIO descriptor leak on register failure
Pull sound fixes from Takashi Iwai:
"A collection of small fixes. All changes are device-specific, and
nothing stands out.
- A regression fix for HD-audio HDMI probe
- USB-audio hardening patches for issues spotted by fuzzers
- ASoC fixes for TAS278x, SoundWire and Cirrus
- Usual HD-audio and USB-audio quirks"
* tag 'sound-6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Add native DSD quirks for PureAudio DAC series
ASoC: rsnd: fix OF node reference leak in rsnd_ssiu_probe()
ALSA: hda/tas2781: Correct the wrong project ID
ALSA: usb-audio: Fix NULL pointer dereference in snd_usb_mixer_controls_badd
ASoC: SDCA: bug fix while parsing mipi-sdca-control-cn-list
ALSA: usb-audio: Fix potential overflow of PCM transfer buffer
ALSA: hda/tas2781: Add new quirk for HP new projects
ASoC: tas2781: fix getting the wrong device number
ASoC: codecs: va-macro: fix resource leak in probe error path
ASoC: tas2783A: Fix issues in firmware parsing
ASoC: sdw_utils: fix device reference leak in is_sdca_endpoint_present()
ASoC: cs4271: Fix regulator leak on probe failure
ALSA: hda/hdmi: Fix breakage at probing nvhdmi-mcp driver
ASoC: da7213: Use component driver suspend/resume
ALSA: usb-audio: add min_mute quirk for SteelSeries Arctis
ASoC: doc: cs35l56: Update firmware filename description for B0 silicon
Pull block fixlet from Jens Axboe:
"Been sitting on this one for a week or two, planning on sending it out
when there were other block changes for 6.18. But as that hasn't
materialized in the second week of sitting on it, let's flush it out.
A previous commit updated my git tree locations, but one was missed as
it was already set to the git.kernel.org one. But the git location swap
also renamed the actual tree from linux-block to just linux, let's get
that last one updated too"
* tag 'block-6.18-20251114' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
MAINTAINERS: correct git location for block layer tree
Pull io_uring fixes from Jens Axboe:
- Use the actual segments in a request when for bvec based buffers
- Fix an odd case where the iovec might get leaked for a read/write
request, if it was newly allocated, overflowed the alloc cache, and
hit an early error
- Minor tweak to the query API added in this release, returning the
number of available entries
* tag 'io_uring-6.18-20251113' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
io_uring/rsrc: don't use blk_rq_nr_phys_segments() as number of bvecs
io_uring/query: return number of available queries
io_uring/rw: ensure allocated iovec gets cleared for early failure
A test case for a situation when widen_imprecise_scalars() is called
with old->allocated_stack > cur->allocated_stack. Test structure:
def widening_stack_size_bug():
r1 = 0
for r6 in 0..1:
iterator_with_diff_stack_depth(r1)
r1 = 42
def iterator_with_diff_stack_depth(r1):
if r1 != 42:
use 128 bytes of stack
iterator based loop
iterator_with_diff_stack_depth() is verified with r1 == 0 first and
r1 == 42 next. Causing stack usage of 128 bytes on a first visit and 8
bytes on a second. Such arrangement triggered a KASAN error in
widen_imprecise_scalars().
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20251114025730.772723-2-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The usage pattern for widen_imprecise_scalars() looks as follows:
prev_st = find_prev_entry(env, ...);
queued_st = push_stack(...);
widen_imprecise_scalars(env, prev_st, queued_st);
Where prev_st is an ancestor of the queued_st in the explored states
tree. This ancestor is not guaranteed to have same allocated stack
depth as queued_st. E.g. in the following case:
def main():
for i in 1..2:
foo(i) // same callsite, differnt param
def foo(i):
if i == 1:
use 128 bytes of stack
iterator based loop
Here, for a second 'foo' call prev_st->allocated_stack is 128,
while queued_st->allocated_stack is much smaller.
widen_imprecise_scalars() needs to take this into account and avoid
accessing bpf_verifier_state->frame[*]->stack out of bounds.
Fixes: 2793a8b015 ("bpf: exact states comparison for iterator convergence checks")
Reported-by: Emil Tsalapatis <emil@etsalapatis.com>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20251114025730.772723-1-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Commit b6bcbce335 ("soc/tegra: pmc: Ensure power-domains are in a
known state") was introduced so that all power domains get initialized
to a known working state when booting and it does this by shutting them
down (including asserting resets and disabling clocks) before registering
each power domain with the genpd framework, leaving it to each driver to
later on power its needed domains.
This caused the Google Pixel C to hang when booting due to a workaround
in the DSI driver introduced in commit b22fd0b963 ("drm/tegra: dsi:
Clear enable register if powered by bootloader") meant to handle the case
where the bootloader enabled the DSI hardware module. The workaround relies
on reading a hardware register to determine the current status and after
b6bcbce335 that now happens in a powered down state thus leading to
the boot hang.
Fix this by reverting b22fd0b963 since currently we are guaranteed
that the hardware will be fully reset by the time we start enabling the
DSI module.
Fixes: b6bcbce335 ("soc/tegra: pmc: Ensure power-domains are in a known state")
Cc: stable@vger.kernel.org
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patch.msgid.link/20251103-diogo-smaug_ec_typec-v1-1-be656ccda391@tecnico.ulisboa.pt
Add a call to put_pid() corresponding to get_task_pid().
host1x_memory_context_alloc() does not take ownership of the PID so we
need to free it here to avoid leaking.
Signed-off-by: Prateek Agarwal <praagarwal@nvidia.com>
Fixes: e09db97889 ("drm/tegra: Support context isolation")
[mperttunen@nvidia.com: reword commit message]
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patch.msgid.link/20250919-host1x-put-pid-v1-1-19c2163dfa87@nvidia.com
syzbot found that cls_bpf_classify() is able to change
tc_skb_cb(skb)->drop_reason triggering a warning in sk_skb_reason_drop().
WARNING: CPU: 0 PID: 5965 at net/core/skbuff.c:1192 __sk_skb_reason_drop net/core/skbuff.c:1189 [inline]
WARNING: CPU: 0 PID: 5965 at net/core/skbuff.c:1192 sk_skb_reason_drop+0x76/0x170 net/core/skbuff.c:1214
struct tc_skb_cb has been added in commit ec624fe740 ("net/sched:
Extend qdisc control block with tc control block"), which added a wrong
interaction with db58ba4592 ("bpf: wire in data and data_end for
cls_act_bpf").
drop_reason was added later.
Add bpf_prog_run_data_pointers() helper to save/restore the net_sched
storage colliding with BPF data_meta/data_end.
Fixes: ec624fe740 ("net/sched: Extend qdisc control block with tc control block")
Reported-by: syzbot <syzkaller@googlegroups.com>
Closes: https://lore.kernel.org/netdev/6913437c.a70a0220.22f260.013b.GAE@google.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20251112125516.1563021-1-edumazet@google.com
Pull crypto fix from Herbert Xu:
- Fix device reference leak in hisilicon
* tag 'v6.18-p5' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: hisilicon/qm - Fix device reference leak in qm_get_qos_value
Pull smb client fixes from Steve French:
- Multichannel reconnect channel selection fix
- Fix for smbdirect (RDMA) disconnect bug
- Fix for incorrect username length check
- Fix memory leak in mount parm processing
* tag 'v6.18-rc5-smb-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb: client: let smbd_disconnect_rdma_connection() turn CREATED into DISCONNECTED
smb: fix invalid username check in smb3_fs_context_parse_param()
cifs: client: fix memory leak in smb3_fs_context_parse_param
smb: client: fix cifs_pick_channel when channel needs reconnect
The irq_domain_free_irqs() helper requires that the irq_domain_ops->free
callback is implemented. Otherwise, the kernel reports the warning message
"NULL pointer, cannot free irq" when irq_dispose_mapping() is invoked to
release the per-HART local interrupts.
Set irq_domain_ops->free to irq_domain_free_irqs_top() to cure that.
Fixes: 832f15f426 ("RISC-V: Treat IPIs as normal Linux IRQs")
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/20251114-rv-intc-fix-v1-1-a3edd1c1a868@sifive.com
When a zero ASCE is passed to the __ptep_rdp() inline assembly, the
generated instruction should have the R3 field of the instruction set to
zero. However the inline assembly is written incorrectly: for such cases a
zero is loaded into a register allocated by the compiler and this register
is then used by the instruction.
This means that selected TLB entries may not be flushed since the specified
ASCE does not match the one which was used when the selected TLB entries
were created.
Fix this by removing the asce and opt parameters of __ptep_rdp(), since
all callers always pass zero, and use a hard-coded register zero for
the R3 field.
Fixes: 0807b85652 ("s390/mm: add support for RDP (Reset DAT-Protection)")
Cc: stable@vger.kernel.org
Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The PureAudio APA DAC and Lotus DAC5 series are USB Audio
2.0 Class devices that support native Direct Stream Digital (DSD)
playback via specific vendor protocols.
Without these quirks, the devices may only function in standard
PCM mode, or fail to correctly report their DSD format capabilities
to the ALSA framework, preventing native DSD playback under Linux.
This commit adds new quirk entries for the mentioned DAC models
based on their respective Vendor/Product IDs (VID:PID), for example:
0x16d0:0x0ab1 (APA DAC), 0x16d0:0xeca1 (DAC5 series), etc.
The quirk ensures correct DSD format handling by setting the required
SNDRV_PCM_FMTBIT_DSD_U32_BE format bit and defining the DSD-specific
Audio Class 2.0 (AC2.0) endpoint configurations. This allows the ALSA
DSD API to correctly address the device for high-bitrate DSD streams,
bypassing the need for DoP (DSD over PCM).
Test on APA DAC and Lotus DAC5 SE under Arch Linux.
Tested-by: Lushih Hsieh <bruce@mail.kh.edu.tw>
Signed-off-by: Lushih Hsieh <bruce@mail.kh.edu.tw>
Link: https://patch.msgid.link/20251114052053.54989-1-bruce@mail.kh.edu.tw
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The xfrm_add_acquire() function constructs an xfrm policy by calling
xfrm_policy_construct(). This allocates the policy structure and
potentially associates a security context and a device policy with it.
However, at the end of the function, the policy object is freed using
only kfree() . This skips the necessary cleanup for the security context
and device policy, leading to a memory leak.
To fix this, invoke the proper cleanup functions xfrm_dev_policy_delete(),
xfrm_dev_policy_free(), and security_xfrm_policy_free() before freeing the
policy object. This approach mirrors the error handling path in
xfrm_add_policy(), ensuring that all associated resources are correctly
released.
Fixes: 980ebd2579 ("[IPSEC]: Sync series - acquire insert")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
ASoC: Fixes for v6.18
A small collection of fixes, all driver specific and none especially
remarkable unless you have the hardware (many not even then).
The function mlxsw_sp_flower_stats() calls mlxsw_sp_acl_ruleset_get() to
obtain a ruleset reference. If the subsequent call to
mlxsw_sp_acl_rule_lookup() fails to find a rule, the function returns
an error without releasing the ruleset reference, causing a memory leak.
Fix this by using a goto to the existing error handling label, which
calls mlxsw_sp_acl_ruleset_put() to properly release the reference.
Fixes: 7c1b8eb175 ("mlxsw: spectrum: Add support for TC flower offload statistics")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20251112052114.1591695-1-zilin@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ethtool tsconfig Netlink path can trigger a null pointer
dereference. A call chain such as:
tsconfig_prepare_data() ->
dev_get_hwtstamp_phylib() ->
vlan_hwtstamp_get() ->
generic_hwtstamp_get_lower() ->
generic_hwtstamp_ioctl_lower()
results in generic_hwtstamp_ioctl_lower() being called with
kernel_cfg->ifr as NULL.
The generic_hwtstamp_ioctl_lower() function does not expect
a NULL ifr and dereferences it, leading to a system crash.
Fix this by adding a NULL check for kernel_cfg->ifr in
generic_hwtstamp_ioctl_lower(). If ifr is NULL, return -EINVAL.
Fixes: 6e9e2eed4f ("net: ethtool: Add support for tsconfig command to get/set hwtstamp config")
Closes: https://lore.kernel.org/cd6a7056-fa6d-43f8-b78a-f5e811247ba8@linux.dev
Signed-off-by: Jiaming Zhang <r772577952@gmail.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20251111173652.749159-2-r772577952@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull VFIO seftest fixes from Alex Williamson:
- Fix vfio selftests to remove the expectation that the IOMMU supports
a 64-bit IOVA space.
These manifest both in the original set of tests introduced this
development cycle in identity mapping the IOVA to buffer virtual
address space, as well as the more recent boundary testing.
Implement facilities for collecting the valid IOVA ranges from the
backend, implement a simple IOVA allocator, and use the information
for determining extents (Alex Mastro)
* tag 'vfio-v6.18-rc6' of https://github.com/awilliam/linux-vfio:
vfio: selftests: replace iova=vaddr with allocated iovas
vfio: selftests: add iova allocator
vfio: selftests: fix map limit tests to use last available iova
vfio: selftests: add iova range query helpers
Pull hwmon fixes from Guenter Roeck:
- gpd-fan: Fix compilation error for non-ACPI builds, and initialize EC
when loading the driver
* tag 'hwmon-for-v6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (gpd-fan) initialize EC on driver load for Win 4
hwmon: (gpd-fan) Fix compilation error in non-ACPI builds
Pull power management fixes from Rafael Wysocki:
"These fix issues related to the handling of compressed hibernation
images and a recent intel_pstate driver regression:
- Fix issues related to using inadequate data types and incorrect use
of atomic variables in the compressed hibernation images handling
code that were introduced during the 6.9 development cycle (Mario
Limonciello)
- Move a X86_FEATURE_IDA check from turbo_is_disabled() to the places
where a new value for MSR_IA32_PERF_CTL is computed in intel_pstate
to address a regression preventing users from enabling turbo
frequencies post-boot (Srinivas Pandruvada)"
* tag 'pm-6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Check IDA only before MSR_IA32_PERF_CTL writes
PM: hibernate: Fix style issues in save_compressed_image()
PM: hibernate: Use atomic64_t for compressed_size variable
PM: hibernate: Emit an error when image writing fails
Pull ACPI fixes from Rafael Wysocki:
"These fix issues in the ACPI CPPC library and in the recently added
parser for the ACPI MRRM table:
- Limit some checks in the ACPI CPPC library to online CPUs to avoid
accessing uninitialized per-CPU variables when some CPUs are
offline to start with, like during boot with 'nosmt=force' (Gautham
Shenoy)
- Rework add_boot_memory_ranges() in the ACPI MRRM table parser to
fix memory leaks and improve error handling (Kaushlendra Kumar)"
* tag 'acpi-6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: MRRM: Fix memory leaks and improve error handling
ACPI: CPPC: Limit perf ctrs in PCC check only to online CPUs
ACPI: CPPC: Perform fast check switch only for online CPUs
ACPI: CPPC: Check _CPC validity for only the online CPUs
ACPI: CPPC: Detect preferred core availability on online CPUs
We've had reports from the field that some RK3588 Tiger have random
issues with eMMC errors.
Applying commit a28352cf2d ("mmc: sdhci-of-dwcmshc: Change
DLL_STRBIN_TAPNUM_DEFAULT to 0x4") didn't help and seemed to have made
things worse for our board.
Our HW department checked the eMMC lines and reported that they are too
long and don't look great so signal integrity is probably not the best.
Note that not all Tigers with the same eMMC chip have errors, so the
suspicion is that we're really on the edge in terms of signal integrity
and only a handful devices are failing. Additionally, we have RK3588
Jaguars with the same eMMC chip but the layout is different and we also
haven't received reports about those so far.
Lowering the max-frequency to 150MHz from 200MHz instead of simply
disabling HS400 was briefly tested and seem to work as well. We've
disabled HS400 downstream and haven't received reports since so we'll go
with that instead of lowering the max-frequency.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Fixes: 6173ef24b3 ("arm64: dts: rockchip: add RK3588-Q7 (Tiger) SoM")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251112-tiger-hs200-v1-1-b50adac107c0@cherry.de
[added Fixes tag and stable-cc from 2nd mail]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Jiayuan Chen says:
====================
mptcp: Fix conflicts between MPTCP and sockmap
Overall, we encountered a warning [1] that can be triggered by running the
selftest I provided.
sockmap works by replacing sk_data_ready, recvmsg, sendmsg operations and
implementing fast socket-level forwarding logic:
1. Users can obtain file descriptors through userspace socket()/accept()
interfaces, then call BPF syscall to perform these replacements.
2. Users can also use the bpf_sock_hash_update helper (in sockops programs)
to replace handlers when TCP connections enter ESTABLISHED state
(BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB/BPF_SOCK_OPS_ACTIVE_ESTABLISHED_CB)
However, when combined with MPTCP, an issue arises: MPTCP creates subflow
sk's and performs TCP handshakes, so the BPF program obtains subflow sk's
and may incorrectly replace their sk_prot. We need to reject such
operations. In patch 1, we set psock_update_sk_prot to NULL in the
subflow's custom sk_prot.
Additionally, if the server's listening socket has MPTCP enabled and the
client's TCP also uses MPTCP, we should allow the combination of subflow
and sockmap. This is because the latest Golang programs have enabled MPTCP
for listening sockets by default [2]. For programs already using sockmap,
upgrading Golang should not cause sockmap functionality to fail.
Patch 2 prevents the WARNING from occurring.
Despite these patches fixing stream corruption, users of sockmap must set
GODEBUG=multipathtcp=0 to disable MPTCP until sockmap fully supports it.
[1] truncated warning:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 388 at net/mptcp/protocol.c:68 mptcp_stream_accept+0x34c/0x380
Modules linked in:
RIP: 0010:mptcp_stream_accept+0x34c/0x380
RSP: 0018:ffffc90000cf3cf8 EFLAGS: 00010202
PKRU: 55555554
Call Trace:
<TASK>
do_accept+0xeb/0x190
? __x64_sys_pselect6+0x61/0x80
? _raw_spin_unlock+0x12/0x30
? alloc_fd+0x11e/0x190
__sys_accept4+0x8c/0x100
__x64_sys_accept+0x1f/0x30
x64_sys_call+0x202f/0x20f0
do_syscall_64+0x72/0x9a0
? switch_fpu_return+0x60/0xf0
? irqentry_exit_to_user_mode+0xdb/0x1e0
? irqentry_exit+0x3f/0x50
? clear_bhb_loop+0x50/0xa0
? clear_bhb_loop+0x50/0xa0
? clear_bhb_loop+0x50/0xa0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
</TASK>
---[ end trace 0000000000000000 ]---
[2]: https://go-review.googlesource.com/c/go/+/607715
====================
Link: https://patch.msgid.link/20251111060307.194196-1-jiayuan.chen@linux.dev
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
The sockmap feature allows bpf syscall from userspace, or based
on bpf sockops, replacing the sk_prot of sockets during protocol stack
processing with sockmap's custom read/write interfaces.
'''
tcp_rcv_state_process()
syn_recv_sock()/subflow_syn_recv_sock()
tcp_init_transfer(BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB)
bpf_skops_established <== sockops
bpf_sock_map_update(sk) <== call bpf helper
tcp_bpf_update_proto() <== update sk_prot
'''
When the server has MPTCP enabled but the client sends a TCP SYN
without MPTCP, subflow_syn_recv_sock() performs a fallback on the
subflow, replacing the subflow sk's sk_prot with the native sk_prot.
'''
subflow_syn_recv_sock()
subflow_ulp_fallback()
subflow_drop_ctx()
mptcp_subflow_ops_undo_override()
'''
Then, this subflow can be normally used by sockmap, which replaces the
native sk_prot with sockmap's custom sk_prot. The issue occurs when the
user executes accept::mptcp_stream_accept::mptcp_fallback_tcp_ops().
Here, it uses sk->sk_prot to compare with the native sk_prot, but this
is incorrect when sockmap is used, as we may incorrectly set
sk->sk_socket->ops.
This fix uses the more generic sk_family for the comparison instead.
Additionally, this also prevents a WARNING from occurring:
result from ./scripts/decode_stacktrace.sh:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 337 at net/mptcp/protocol.c:68 mptcp_stream_accept \
(net/mptcp/protocol.c:4005)
Modules linked in:
...
PKRU: 55555554
Call Trace:
<TASK>
do_accept (net/socket.c:1989)
__sys_accept4 (net/socket.c:2028 net/socket.c:2057)
__x64_sys_accept (net/socket.c:2067)
x64_sys_call (arch/x86/entry/syscall_64.c:41)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
RIP: 0033:0x7f87ac92b83d
---[ end trace 0000000000000000 ]---
Fixes: 0b4f33def7 ("mptcp: fix tcp fallback crash")
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20251111060307.194196-3-jiayuan.chen@linux.dev
Multiple threads may be creating and destroying BFD objects in
situations like `perf top`.
Without appropriate initialization crashes may occur during libbfd's
cache management.
BFD's locks require recursive mutexes, add support for these.
Committer testing:
This happens only when building with 'make BUILD_NONDISTRO=1' and having
the binutils-devel package (or equivalent) installed, i.e. linking with
binutils devel files, an opt-in perf build.
Before:
root@x1:~# perf top
perf: Segmentation fault
-------- backtrace --------
<SNIP multiple failed attempts at printing a backtrace>
root@x1:~#
After this patch it works as before.
Closes: https://lore.kernel.org/lkml/aQt66zhfxSA80xwt@gentoo.org/
Fixes: 95931d9a59 ("perf libbfd: Move libbfd functionality to its own file")
Reported-by: Guilherme Amadio <amadio@gentoo.org>
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Couple of independent fixes:
1. Wire in SIGSEGV handler that terminates the test with a failure code.
2. Use "--lock-cgroup" instead of "-g"; "-g" was proposed but never
merged. See commit 4d1792d0a2 ("perf lock contention: Add
--lock-cgroup option")
3. Call cleanup() on every normal exit so trap_cleanup() doesn't mistake
it for an unexpected signal and emit a false-negative "Unexpected
signal in main" message.
Before patch:
# ./perf test -vv "lock contention"
85: kernel lock contention analysis test:
--- start ---
test child forked, pid 610711
Testing perf lock record and perf lock contention
Testing perf lock contention --use-bpf
Testing perf lock record and perf lock contention at the same time
Testing perf lock contention --threads
Testing perf lock contention --lock-addr
Testing perf lock contention --lock-cgroup
Unexpected signal in test_aggr_cgroup
---- end(0) ----
85: kernel lock contention analysis test : Ok
After patch:
# ./perf test -vv "lock contention"
85: kernel lock contention analysis test:
--- start ---
test child forked, pid 602637
Testing perf lock record and perf lock contention
Testing perf lock contention --use-bpf
Testing perf lock record and perf lock contention at the same time
Testing perf lock contention --threads
Testing perf lock contention --lock-addr
Testing perf lock contention --lock-cgroup
Testing perf lock contention --type-filter (w/ spinlock)
Testing perf lock contention --lock-filter (w/ tasklist_lock)
Testing perf lock contention --callstack-filter (w/ unix_stream)
[Skip] Could not find 'unix_stream'
Testing perf lock contention --callstack-filter with task aggregation
[Skip] Could not find 'unix_stream'
Testing perf lock contention --cgroup-filter
Testing perf lock contention CSV output
---- end(0) ----
85: kernel lock contention analysis test : Ok
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ananth Narayan <ananth.narayan@amd.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandipan Das <sandipan.das@amd.com>
Cc: Santosh Shukla <santosh.shukla@amd.com>
Cc: Tycho Andersen <tycho@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pick the changes in:
9d7dfb95da ("KVM: VMX: Inject #UD if guest tries to execute SEAMCALL or TDCALL")
The 'perf kvm-stat' tool uses the exit reasons that are included in the
VMX_EXIT_REASONS define, this new SEAMCALL isn't included there (TDCALL
is), so shouldn't be causing any change in behaviour, this patch ends up
being just addressess the following perf build warning:
Warning: Kernel ABI header differences:
diff -u tools/arch/x86/include/uapi/asm/vmx.h arch/x86/include/uapi/asm/vmx.h
Please see tools/include/uapi/README for further details.
Cc: Sean Christopherson <seanjc@google.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This is one more remnant of the BUILD_NONDISTRO series to make building
with binutils-devel opt-in due to license incompatibility.
In this case just the references at link time were still in place, which
make building the test-all.bin file fail, which wasn't detected before
probably because the last test was done with binutils-devel available,
doh.
Now:
$ rpm -q binutils-devel
package binutils-devel is not installed
$ file /tmp/build/perf-tools/feature/test-all.bin
/tmp/build/perf-tools/feature/test-all.bin: ELF 64-bit LSB executable, x86-64, version 1 (SYSV),
dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2,
BuildID[sha1]=4b5388a346b51f1b993f0b0dbd49f4570769b03c, for GNU/Linux 3.2.0, not stripped
$
Fixes: 970ae86307 ("perf build: The bfd features are opt-in, stop testing for them by default")
Reviewed-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
With commit f0d0f978f3 ("perf header: Don't write empty BPF/BTF
info"), the write_bpf_( prog_info() | btf() ) functions exit without
writing anything if env->bpf_prog.(infos| btfs)_cnt is zero.
process_bpf_( prog_info() | btf() ), however, still expect a "count"
value to exist in the data file. If btf information is empty, for
example, process_bpf_btf will read garbage or some other data as the
number of btf nodes in the data file. As a result, the data file will
not be processed correctly.
Instead, write the count to the data file and exit if it is zero.
Fixes: f0d0f978f3 ("perf header: Don't write empty BPF/BTF info")
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Thomas Falcon <thomas.falcon@intel.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Merge fixes for issues related to the handling of compressed hibernation
images that were introduced during the 6.9 development cycle.
* pm-sleep:
PM: hibernate: Fix style issues in save_compressed_image()
PM: hibernate: Use atomic64_t for compressed_size variable
PM: hibernate: Emit an error when image writing fails
Pull slab fix from Vlastimil Babka:
- Fix memory leak of objects from remote NUMA node when bulk freeing to
a cache with sheaves (Harry Yoo)
* tag 'slab-for-6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
mm/slub: fix memory leak in free_to_pcs_bulk()
Merge ACPI CPPC library fixes and an ACPI MRRM table parser fix for
6.18-rc6.
* acpi-cppc:
ACPI: CPPC: Limit perf ctrs in PCC check only to online CPUs
ACPI: CPPC: Perform fast check switch only for online CPUs
ACPI: CPPC: Check _CPC validity for only the online CPUs
ACPI: CPPC: Detect preferred core availability on online CPUs
* acpi-tables:
ACPI: MRRM: Fix memory leaks and improve error handling
Pull kselftest fix from Shuah Khan:
"Fixes event-filter-function.tc tracing test failure caused when a
first run to sample events triggers kmem_cache_free which interferes
with the rest of the test.
Fix this by calling sample_events twice to eliminate the
kmem_cache_free related noise from the sampling"
* tag 'linux_kselftest-fixes-6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/tracing: Run sample events to clear page cache events
The commit 989b09b739 ("slab: skip percpu sheaves for remote object
freeing") introduced the remote_objects array in free_to_pcs_bulk() to
skip sheaves when objects from a remote node are freed.
However, the array is flushed only when:
1) the array becomes full (++remote_nr >= PCS_BATCH_MAX), or
2) slab_free_hook() returns false and size becomes zero.
When neither of the conditions is met, objects in the array are leaked.
This resulted in a memory leak [1], where 82 GiB of memory was allocated
for the maple_node cache.
Flush the array after successfully freeing objects to sheaves
in the do_free: path.
In the meantime, move the snippet if (!size) goto flush_remote; outside
the while loop for readability. Let's say all objects in the array are
from a remote node: then we acquire s->cpu_sheaves->lock and try to free
an object even when size is zero. This doesn't appear to be harmful,
but isn't really readable.
Reported-by: Tytus Rogalewski <admin@simplepod.ai>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220765 [1]
Closes: https://lore.kernel.org/linux-mm/20251107094809.12e9d705b7bf4815783eb184@linux-foundation.org
Closes: https://lore.kernel.org/all/aRGDTwbt2EIz2CYn@hyeyoo
Fixes: 989b09b739 ("slab: skip percpu sheaves for remote object freeing")
Signed-off-by: Harry Yoo <harry.yoo@oracle.com>
Link: https://patch.msgid.link/20251111125331.12246-1-harry.yoo@oracle.com
Acked-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Tested-by: Darrick J. Wong <djwong@kernel.org>
Tested-by: Tytus Rogalewski <admin@simplepod.ai>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
For PREEMPT_RT=y kernels, the deferred_irq_workfn() is executed in
the per-cpu irq_work/* task context and not disable-irq, if the rq
returned by container_of() is current CPU's rq, the following scenarios
may occur:
lock(&rq->__lock);
<Interrupt>
lock(&rq->__lock);
This commit use IRQ_WORK_INIT_HARD() to replace init_irq_work() to
initialize rq->scx.deferred_irq_work, make the deferred_irq_workfn()
is always invoked in hard-irq context.
Signed-off-by: Zqiang <qiang.zhang@linux.dev>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sockmap feature allows bpf syscall from userspace, or based on bpf
sockops, replacing the sk_prot of sockets during protocol stack processing
with sockmap's custom read/write interfaces.
'''
tcp_rcv_state_process()
subflow_syn_recv_sock()
tcp_init_transfer(BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB)
bpf_skops_established <== sockops
bpf_sock_map_update(sk) <== call bpf helper
tcp_bpf_update_proto() <== update sk_prot
'''
Consider two scenarios:
1. When the server has MPTCP enabled and the client also requests MPTCP,
the sk passed to the BPF program is a subflow sk. Since subflows only
handle partial data, replacing their sk_prot is meaningless and will
cause traffic disruption.
2. When the server has MPTCP enabled but the client sends a TCP SYN
without MPTCP, subflow_syn_recv_sock() performs a fallback on the
subflow, replacing the subflow sk's sk_prot with the native sk_prot.
'''
subflow_ulp_fallback()
subflow_drop_ctx()
mptcp_subflow_ops_undo_override()
'''
Subsequently, accept::mptcp_stream_accept::mptcp_fallback_tcp_ops()
converts the subflow to plain TCP.
For the first case, we should prevent it from being combined with sockmap
by setting sk_prot->psock_update_sk_prot to NULL, which will be blocked by
sockmap's own flow.
For the second case, since subflow_syn_recv_sock() has already restored
sk_prot to native tcp_prot/tcpv6_prot, no further action is needed.
Fixes: cec37a6e41 ("mptcp: Handle MP_CAPABLE options for outgoing connections")
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20251111060307.194196-2-jiayuan.chen@linux.dev
The stub implementation of arch_xfer_to_guest_mode_handle_work() is
guarded by an #ifndef that incorrectly checks for the name
arch_xfer_to_guest_mode_work instead. It seems the function was renamed
to add "_handle" as a late change to the original patch, and the #ifndef
wasn't updated to go with it.
Change the #ifndef to match the name of the function. No users right now,
so no need to update any architecture code.
Fixes: 935ace2fb5 ("entry: Provide infrastructure for work before transitioning to guest mode")
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/20251105-entry-fix-ifndef-v1-1-d8d28045b627@linux.ibm.com
Felix Maurer says:
====================
hsr: Send correct HSRv0 supervision frames
Hangbin recently reported that the hsr selftests were failing and noted
that the entries in the node table were not merged, i.e., had
00:00:00:00:00:00 as MacAddressB forever [1].
This failure only occured with HSRv0 because it was not sending
supervision frames anymore. While debugging this I found that we were
not really following the HSRv0 standard for the supervision frames we
sent, so I additionally made a few changes to get closer to the standard
and restore a more correct behavior we had a while ago.
The selftests can still fail because they take a while and run into the
timeout. I did not include a change of the timeout because I have more
improvements to the selftests mostly ready that change the test duration
but are net-next material.
[1]: https://lore.kernel.org/netdev/aMONxDXkzBZZRfE5@fedora/
====================
Link: https://patch.msgid.link/cover.1762876095.git.fmaurer@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For HSRv0, the path_id has the following meaning:
- 0000: PRP supervision frame
- 0001-1001: HSR ring identifier
- 1010-1011: Frames from PRP network (A/B, with RedBoxes)
- 1111: HSR supervision frame
Follow the IEC 62439-3:2010 standard more closely by setting the right
path_id for HSRv0 supervision frames (actually, it is correctly set when
the frame is constructed, but hsr_set_path_id() overwrites it) and set a
fixed HSR ring identifier of 1. The ring identifier seems to be generally
unused and we ignore it anyways on reception, but some fixed identifier is
definitely better than using one identifier in one direction and a wrong
identifier in the other.
This was also the behavior before commit f266a683a4 ("net/hsr: Better
frame dispatch") which introduced the alternating path_id. This was later
moved to hsr_set_path_id() in commit 451d8123f8 ("net: prp: add packet
handling support").
The IEC 62439-3:2010 also contains 6 unused bytes after the MacAddressA in
the HSRv0 supervision frames. Adjust a TODO comment accordingly.
Fixes: f266a683a4 ("net/hsr: Better frame dispatch")
Fixes: 451d8123f8 ("net: prp: add packet handling support")
Signed-off-by: Felix Maurer <fmaurer@redhat.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://patch.msgid.link/ea0d5133cd593856b2fa673d6e2067bf1d4d1794.1762876095.git.fmaurer@redhat.com
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The MODULE_PARM_DESC string for the "active" parameter is missing a
space and has an extraneous trailing ']' character. Correct these.
Before patch:
$ modinfo -p ./drm_client_lib.ko
active:Choose which drm client to start, default isfbdev] (string)
After patch:
$ modinfo -p ./drm_client_lib.ko
active:Choose which drm client to start, default is fbdev (string)
Fixes: f7b42442c4 ("drm/log: Introduce a new boot logger to draw the kmsg on the screen")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20251112010920.2355712-1-rdunlap@infradead.org
Pull erofs fixes from Gao Xiang:
- Add Chunhai Guo as a EROFS reviewer to get more eyes from interested
industry vendors
- Fix infinite loop caused by incomplete crafted zstd-compressed data
(thanks to Robert again!)
* tag 'erofs-for-6.18-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: avoid infinite loop due to incomplete zstd-compressed data
MAINTAINERS: erofs: add myself as reviewer
Pull smb server fixes from Steve French:
- Fix smbdirect (RDMA) disconnect hang bug
- Fix potential Denial of Service when connection limit exceeded
- Fix smbdirect (RDMA) connection (potentially accessing freed memory)
bug
* tag 'v6.18-rc5-smb-server-fixes' of git://git.samba.org/ksmbd:
smb: server: let smb_direct_disconnect_rdma_connection() turn CREATED into DISCONNECTED
ksmbd: close accepted socket when per-IP limit rejects connection
smb: server: rdma: avoid unmapping posted recv on accept failure
The purpose of commit 703eec1b24 ("virtio_net: fixing XDP for fully
checksummed packets handling") is to record the flags in advance, as
their value may be overwritten in the XDP case. However, the flags
recorded under big mode are incorrect, because in big mode, the passed
buf does not point to the rx buffer, but rather to the page of the
submitted buffer. This commit fixes this issue.
For the small mode, the commit c11a49d58a ("virtio_net: Fix mismatched
buf address when unmapping for small packets") fixed it.
Tested-by: Alyssa Ross <hi@alyssa.is>
Fixes: 703eec1b24 ("virtio_net: fixing XDP for fully checksummed packets handling")
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://patch.msgid.link/20251111090828.23186-1-xuanzhuo@linux.alibaba.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pull nfsd fixes from Chuck Lever:
"Address recently reported issues or issues found at the recent NFS
bake-a-thon held in Raleigh, NC.
Issues reported with v6.18-rc:
- Address a kernel build issue
- Reorder SEQUENCE processing to avoid spurious NFS4ERR_SEQ_MISORDERED
Issues that need expedient stable backports:
- Close a refcount leak exposure
- Report support for NFSv4.2 CLONE correctly
- Fix oops during COPY_NOTIFY processing
- Prevent rare crash after XDR encoding failure
- Prevent crash due to confused or malicious NFSv4.1 client"
* tag 'nfsd-6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
Revert "SUNRPC: Make RPCSEC_GSS_KRB5 select CRYPTO instead of depending on it"
nfsd: ensure SEQUENCE replay sends a valid reply.
NFSD: Never cache a COMPOUND when the SEQUENCE operation fails
NFSD: Skip close replay processing if XDR encoding fails
NFSD: free copynotify stateid in nfs4_free_ol_stateid()
nfsd: add missing FATTR4_WORD2_CLONE_BLKSIZE from supported attributes
nfsd: fix refcount leak in nfsd_set_fh_dentry()
Pull dma-mapping fixes from Marek Szyprowski:
- two minor fixes for DMA API infrastructure: restoring proper
structure padding used in benchmark tests (Qinxin Xia) and global
DMA_BIT_MASK macro rework to make it a bit more clang friendly (James
Clark)
* tag 'dma-mapping-6.18-2025-11-12' of git://git.kernel.org/pub/scm/linux/kernel/git/mszyprowski/linux:
dma-mapping: Allow use of DMA_BIT_MASK(64) in global scope
dma-mapping: benchmark: Restore padding to ensure uABI remained consistent
Pull LoongArch fixes from Huacai Chen:
- Fix a Rust build error
- Fix exception/interrupt, memory management, perf event, hardware
breakpoint, kexec and KVM bugs
* tag 'loongarch-fixes-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: KVM: Fix max supported vCPUs set with EIOINTC
LoongArch: KVM: Skip PMU checking on vCPU context switch
LoongArch: KVM: Restore guest PMU if it is enabled
LoongArch: KVM: Add delay until timer interrupt injected
LoongArch: KVM: Set page with write attribute if dirty track disabled
LoongArch: kexec: Print out debugging message if required
LoongArch: kexec: Initialize the kexec_buf structure
LoongArch: Use correct accessor to read FWPC/MWPC
LoongArch: Refine the init_hw_perf_events() function
LoongArch: Remove __GFP_HIGHMEM masking in pud_alloc_one()
LoongArch: Let {pte,pmd}_modify() record the status of _PAGE_DIRTY
LoongArch: Consolidate max_pfn & max_low_pfn calculation
LoongArch: Consolidate early_ioremap()/ioremap_prot()
LoongArch: Use physical addresses for CSR_MERRENTRY/CSR_TLBRENTRY
LoongArch: Clarify 3 MSG interrupt features
rust: Add -fno-isolate-erroneous-paths-dereference to bindgen_skip_c_flags
Pull alpha fix from Matt Turner:
"Add Magnus as a maintainer of the alpha port"
* tag 'alpha-fixes-v6.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
MAINTAINERS: Add Magnus Lindholm as maintainer for alpha port
Christian reported that f3ac2ff148 ("PCI/ASPM: Enable all ClockPM and
ASPM states for devicetree platforms") broke booting on the A-EON AmigaOne
X1000.
Override the L0s and L1 Support advertised in Link Capabilities by the
X1000 Root Ports ([1959:a002]) so we don't try to enable those states.
Fixes: f3ac2ff148 ("PCI/ASPM: Enable all ClockPM and ASPM states for devicetree platforms")
Fixes: df5192d9bb ("PCI/ASPM: Enable only L0s and L1 for devicetree platforms")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Link: https://lore.kernel.org/r/a41d2ca1-fcd9-c416-b111-a958e92e94bf@xenosoft.de
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Existing quirks to disable ASPM L0s and L1 use pci_disable_link_state(),
which disables ASPM states and prevents their use in the future. But since
they are FINAL quirks, they happen after ASPM has already been enabled.
Here's a typical call path:
pci_host_probe
pci_scan_root_bus_bridge
pci_scan_child_bus
pci_scan_slot
pci_scan_single_device
pci_device_add
pci_fixup_device(pci_fixup_header) # HEADER quirks
pcie_aspm_init_link_state
pcie_config_aspm_path
pcie_config_aspm_link
pcie_config_aspm_dev # ASPM may be enabled
pci_bus_add_devices
pci_bus_add_devices
pci_fixup_device(pci_fixup_final) # FINAL quirks
quirk_disable_aspm_l0s
pci_disable_link_state(dev, PCIE_LINK_STATE_L0S)
Sometimes enabling ASPM can make the link non-functional, so if we know
ASPM is broken on a device, we shouldn't enable it at all, even
temporarily.
Convert the existing quirks to use pcie_aspm_remove_cap() instead, which
overrides the ASPM Support advertised in PCIe Link Capabilities, and make
them HEADER quirks so they run before pcie_aspm_init_link_state() has a
chance to enable ASPM.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://patch.msgid.link/20251110222929.2140564-4-helgaas@kernel.org
Defective devices sometimes advertise support for ASPM L0s or L1 states
even if they don't work correctly.
Cache the L0s Supported and L1 Supported bits early in enumeration so
HEADER quirks can override the ASPM states advertised in Link Capabilities
before pcie_aspm_cap_init() enables ASPM.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://patch.msgid.link/20251110222929.2140564-2-helgaas@kernel.org
rsnd_ssiu_probe() leaks an OF node reference obtained by
rsnd_ssiu_of_node(). The node reference is acquired but
never released across all return paths.
Fix it by declaring the device node with the __free(device_node)
cleanup construct to ensure automatic release when the variable goes
out of scope.
Fixes: 4e7788fb80 ("ASoC: rsnd: add SSIU BUSIF support")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/20251112065709.1522-1-vulab@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
The following lockdep splat was observed while kernel auto-online a CXL
memory region:
======================================================
WARNING: possible circular locking dependency detected
6.17.0djtest+ #53 Tainted: G W
------------------------------------------------------
systemd-udevd/3334 is trying to acquire lock:
ffffffff90346188 (hmem_resource_lock){+.+.}-{4:4}, at: hmem_register_resource+0x31/0x50
but task is already holding lock:
ffffffff90338890 ((node_chain).rwsem){++++}-{4:4}, at: blocking_notifier_call_chain+0x2e/0x70
which lock already depends on the new lock.
[..]
Chain exists of:
hmem_resource_lock --> mem_hotplug_lock --> (node_chain).rwsem
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
rlock((node_chain).rwsem);
lock(mem_hotplug_lock);
lock((node_chain).rwsem);
lock(hmem_resource_lock);
The lock ordering can cause potential deadlock. There are instances
where hmem_resource_lock is taken after (node_chain).rwsem, and vice
versa.
Split out the target update section of hmat_register_target() so that
hmat_callback() only envokes that section instead of attempt to register
hmem devices that it does not need to.
[ dj: Fix up comment to be closer to 80cols. (Jonathan) ]
Fixes: cf8741ac57 ("ACPI: NUMA: HMAT: Register "soft reserved" memory as an "hmem" device")
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Tested-by: Smita Koralahalli <Smita.KoralahalliChannabasappa@amd.com>
Reviewed-by: Smita Koralahalli <Smita.KoralahalliChannabasappa@amd.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://patch.msgid.link/20251105235115.85062-3-dave.jiang@intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Building gpd-fan driver without CONFIG_ACPI results in the following
build errors:
drivers/hwmon/gpd-fan.c: In function ‘gpd_ecram_read’:
drivers/hwmon/gpd-fan.c:228:9: error: implicit declaration of function ‘outb’ [-Werror=implicit-function-declaration]
228 | outb(0x2E, addr_port);
| ^~~~
drivers/hwmon/gpd-fan.c:241:16: error: implicit declaration of function ‘inb’ [-Werror=implicit-function-declaration]
241 | *val = inb(data_port);
The definitions for inb() and outb() come from <linux/io.h>
(specifically through <asm/io.h>), which is implicitly included via
<acpi_io.h>. When CONFIG_ACPI is not set, <acpi_io.h> is not included
resulting in <linux/io.h> to be omitted as well.
Since the driver does not depend on ACPI, remove <linux/acpi.h> and add
<linux/io.h> directly to fix the compilation errors.
Signed-off-by: Gopi Krishna Menon <krishnagopi487@gmail.com>
Link: https://lore.kernel.org/r/20251024202042.752160-1-krishnagopi487@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update scx_task_locks so that it's safe to lock/unlock in a
non-sleepable context in PREEMPT_RT kernels. scx_task_locks is
(non-raw) spinlock used to protect the list of tasks under SCX.
This list is updated during from finish_task_switch(), which
cannot sleep. Regular spinlocks can be locked in such a context
in non-RT kernels, but are sleepable under when CONFIG_PREEMPT_RT=y.
Convert scx_task_locks into a raw spinlock, which is not sleepable
even on RT kernels.
Sample backtrace:
<TASK>
dump_stack_lvl+0x83/0xa0
__might_resched+0x14a/0x200
rt_spin_lock+0x61/0x1c0
? sched_ext_dead+0x2d/0xf0
? lock_release+0xc6/0x280
sched_ext_dead+0x2d/0xf0
? srso_alias_return_thunk+0x5/0xfbef5
finish_task_switch.isra.0+0x254/0x360
__schedule+0x584/0x11d0
? srso_alias_return_thunk+0x5/0xfbef5
? srso_alias_return_thunk+0x5/0xfbef5
? tick_nohz_idle_exit+0x7e/0x120
schedule_idle+0x23/0x40
cpu_startup_entry+0x29/0x30
start_secondary+0xf8/0x100
common_startup_64+0x13e/0x148
</TASK>
Signed-off-by: Emil Tsalapatis <emil@etsalapatis.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Johannes Berg says:
====================
Couple more fixes:
- mwl8k: work around FW expecting a DSSS element in beacons
- ath11k: report correct TX status
- iwlwifi: avoid toggling links due to wrong element use
- iwlwifi: fix beacon template rate on older devices
- iwlwifi: fix loop iterator being used after loop
- mac80211: disallow address changes while using the address
- mac80211: avoid bad rate warning in monitor/sniffer mode
- hwsim: fix potential NULL deref (on monitor injection)
* tag 'wireless-2025-11-12' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: iwlwifi: mld: always take beacon ies in link grading
wifi: iwlwifi: mvm: fix beacon template/fixed rate
wifi: iwlwifi: fix aux ROC time event iterator usage
wifi: mwl8k: inject DSSS Parameter Set element into beacons if missing
wifi: mac80211_hwsim: Fix possible NULL dereference
wifi: mac80211: skip rate verification for not captured PSDUs
wifi: mac80211: reject address change while connecting
wifi: ath11k: zero init info->status in wmi_process_mgmt_tx_comp()
====================
Link: https://patch.msgid.link/20251112114621.15716-5-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit ac4e04d9e3 ("cpufreq: intel_pstate: Unchecked MSR aceess in
legacy mode") introduced a check for feature X86_FEATURE_IDA to verify
turbo mode support. Although this is the correct way to check for turbo
mode support, it causes issues on some platforms that disable turbo
during OS boot, but enable it later [1]. Before adding this feature
check, users were able to get turbo mode frequencies by writing 0 to
/sys/devices/system/cpu/intel_pstate/no_turbo post-boot.
To restore the old behavior on the affected systems while still
addressing the unchecked MSR issue on some Skylake-X systems, check
X86_FEATURE_IDA only immediately before updates of MSR_IA32_PERF_CTL
that may involve setting the Turbo Engage Bit (bit 32).
Fixes: ac4e04d9e3 ("cpufreq: intel_pstate: Unchecked MSR aceess in legacy mode")
Reported-by: Aaron Rainbolt <arainbolt@kfocus.org>
Closes: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2122531 [1]
Tested-by: Aaron Rainbolt <arainbolt@kfocus.org>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject adjustment, changelog edits ]
Link: https://patch.msgid.link/20251111010840.141490-1-srinivas.pandruvada@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
io_buffer_register_bvec() currently uses blk_rq_nr_phys_segments() as
the number of bvecs in the request. However, bvecs may be split into
multiple segments depending on the queue limits. Thus, the number of
segments may overestimate the number of bvecs. For ublk devices, the
only current users of io_buffer_register_bvec(), virt_boundary_mask,
seg_boundary_mask, max_segments, and max_segment_size can all be set
arbitrarily by the ublk server process.
Set imu->nr_bvecs based on the number of bvecs the rq_for_each_bvec()
loop actually yields. However, continue using blk_rq_nr_phys_segments()
as an upper bound on the number of bvecs when allocating imu to avoid
needing to iterate the bvecs a second time.
Link: https://lore.kernel.org/io-uring/20251111191530.1268875-1-csander@purestorage.com/
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Fixes: 27cb27b6d5 ("io_uring: add support for kernel registered bvecs")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
vfio_dma_mapping_test and vfio_pci_driver_test currently use iova=vaddr
as part of DMA mapping operations. However, not all IOMMUs support the
same virtual address width as the processor. For instance, older Intel
consumer platforms only support 39-bits of IOMMU address space. On such
platforms, using the virtual address as the IOVA fails.
Make the tests more robust by using iova_allocator to vend IOVAs, which
queries legally accessible IOVAs from the underlying IOMMUFD or VFIO
container.
Reviewed-by: David Matlack <dmatlack@google.com>
Tested-by: David Matlack <dmatlack@google.com>
Signed-off-by: Alex Mastro <amastro@fb.com>
Link: https://lore.kernel.org/r/20251111-iova-ranges-v3-4-7960244642c5@fb.com
Signed-off-by: Alex Williamson <alex@shazbot.org>
VFIO selftests need to map IOVAs from legally accessible ranges, which
could vary between hardware. Tests in vfio_dma_mapping_test.c are making
excessively strong assumptions about which IOVAs can be mapped.
Add vfio_iommu_iova_ranges(), which queries IOVA ranges from the
IOMMUFD or VFIO container associated with the device. The queried ranges
are normalized to IOMMUFD's iommu_iova_range representation so that
handling of IOVA ranges up the stack can be implementation-agnostic.
iommu_iova_range and vfio_iova_range are equivalent, so bias to using the
new interface's struct.
Query IOMMUFD's ranges with IOMMU_IOAS_IOVA_RANGES.
Query VFIO container's ranges with VFIO_IOMMU_GET_INFO and
VFIO_IOMMU_TYPE1_INFO_CAP_IOVA_RANGE.
The underlying vfio_iommu_type1_info buffer-related functionality has
been kept generic so the same helpers can be used to query other
capability chain information, if needed.
Reviewed-by: David Matlack <dmatlack@google.com>
Tested-by: David Matlack <dmatlack@google.com>
Signed-off-by: Alex Mastro <amastro@fb.com>
Link: https://lore.kernel.org/r/20251111-iova-ranges-v3-1-7960244642c5@fb.com
Signed-off-by: Alex Williamson <alex@shazbot.org>
The sit driver's packet transmission path calls: sit_tunnel_xmit() ->
update_or_create_fnhe(), which lead to fnhe_remove_oldest() being called
to delete entries exceeding FNHE_RECLAIM_DEPTH+random.
The race window is between fnhe_remove_oldest() selecting fnheX for
deletion and the subsequent kfree_rcu(). During this time, the
concurrent path's __mkroute_output() -> find_exception() can fetch the
soon-to-be-deleted fnheX, and rt_bind_exception() then binds it with a
new dst using a dst_hold(). When the original fnheX is freed via RCU,
the dst reference remains permanently leaked.
CPU 0 CPU 1
__mkroute_output()
find_exception() [fnheX]
update_or_create_fnhe()
fnhe_remove_oldest() [fnheX]
rt_bind_exception() [bind dst]
RCU callback [fnheX freed, dst leak]
This issue manifests as a device reference count leak and a warning in
dmesg when unregistering the net device:
unregister_netdevice: waiting for sitX to become free. Usage count = N
Ido Schimmel provided the simple test validation method [1].
The fix clears 'oldest->fnhe_daddr' before calling fnhe_flush_routes().
Since rt_bind_exception() checks this field, setting it to zero prevents
the stale fnhe from being reused and bound to a new dst just before it
is freed.
[1]
ip netns add ns1
ip -n ns1 link set dev lo up
ip -n ns1 address add 192.0.2.1/32 dev lo
ip -n ns1 link add name dummy1 up type dummy
ip -n ns1 route add 192.0.2.2/32 dev dummy1
ip -n ns1 link add name gretap1 up arp off type gretap \
local 192.0.2.1 remote 192.0.2.2
ip -n ns1 route add 198.51.0.0/16 dev gretap1
taskset -c 0 ip netns exec ns1 mausezahn gretap1 \
-A 198.51.100.1 -B 198.51.0.0/16 -t udp -p 1000 -c 0 -q &
taskset -c 2 ip netns exec ns1 mausezahn gretap1 \
-A 198.51.100.1 -B 198.51.0.0/16 -t udp -p 1000 -c 0 -q &
sleep 10
ip netns pids ns1 | xargs kill
ip netns del ns1
Cc: stable@vger.kernel.org
Fixes: 67d6d681e1 ("ipv4: make exception cache less predictible")
Signed-off-by: Chuang Wang <nashuiliang@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20251111064328.24440-1-nashuiliang@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace disable_irq() with disable_irq_nosync() in msm_pinmux_set_mux()
to prevent deadlock when wakeup IRQ is triggered on the same
GPIO being reconfigured.
The issue occurs when a wakeup IRQ is triggered on a GPIO and the IRQ
handler attempts to reconfigure the same GPIO's pinmux. In this scenario,
msm_pinmux_set_mux() calls disable_irq() which waits for the currently
running IRQ handler to complete, creating a circular dependency that
results in deadlock.
Using disable_irq_nosync() avoids waiting for the IRQ handler to
complete, preventing the deadlock condition while still properly
disabling the interrupt during pinmux reconfiguration.
Suggested-by: Prasad Sodagudi <prasad.sodagudi@oss.qualcomm.com>
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On VHE, the Fine Grain Traps registers are written to hardware in
kvm_arch_vcpu_load()->..->__activate_traps_hfgxtr(), but the fgt array is
computed later, in kvm_vcpu_load_fgt(). This can lead to zero being written
to the FGT registers the first time a VCPU is loaded. Also, any changes to
the fgt array will be visible only after the VCPU is scheduled out, and
then back in, which is not the intended behaviour.
Fix it by computing the fgt array just before the fgt traps are written
to hardware.
Fixes: fb10ddf35c ("KVM: arm64: Compute per-vCPU FGTs at vcpu_load()")
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
Reviewed-by: Oliver Upton <oupton@kernel.org>
Link: https://patch.msgid.link/20251112102853.47759-1-alexandru.elisei@arm.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
In systemd we're trying to switch the internal credentials setup logic
to new mount API [1], and I noticed fsconfig(FSCONFIG_CMD_RECONFIGURE)
consistently fails on tmpfs with noswap option. This can be trivially
reproduced with the following:
```
int fs_fd = fsopen("tmpfs", 0);
fsconfig(fs_fd, FSCONFIG_SET_FLAG, "noswap", NULL, 0);
fsconfig(fs_fd, FSCONFIG_CMD_CREATE, NULL, NULL, 0);
fsmount(fs_fd, 0, 0);
fsconfig(fs_fd, FSCONFIG_CMD_RECONFIGURE, NULL, NULL, 0); <------ EINVAL
```
After some digging the culprit is shmem_reconfigure() rejecting
!(ctx->seen & SHMEM_SEEN_NOSWAP) && sbinfo->noswap, which is bogus
as ctx->seen serves as a mask for whether certain options are touched
at all. On top of that, noswap option doesn't use fsparam_flag_no,
hence it's not really possible to "reenable" swap to begin with.
Drop the check and redundant SHMEM_SEEN_NOSWAP flag.
[1] https://github.com/systemd/systemd/pull/39637
Fixes: 2c6efe9cf2 ("shmem: add support to ignore swap")
Signed-off-by: Mike Yuan <me@yhndnzj.com>
Link: https://patch.msgid.link/20251108190930.440685-1-me@yhndnzj.com
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
grab_requested_mnt_ns was changed to return error codes on failure, but
its callers were not updated to check for error pointers, still checking
only for a NULL return value.
This commit updates the callers to use IS_ERR() or IS_ERR_OR_NULL() and
PTR_ERR() to correctly check for and propagate errors.
This also makes sure that the logic actually works and mount namespace
file descriptors can be used to refere to mounts.
Christian Brauner <brauner@kernel.org> says:
Rework the patch to be more ergonomic and in line with our overall error
handling patterns.
Fixes: 7b9d14af87 ("fs: allow mount namespace fd")
Cc: Christian Brauner <brauner@kernel.org>
Signed-off-by: Andrei Vagin <avagin@google.com>
Link: https://patch.msgid.link/20251111062815.2546189-1-avagin@google.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
One of the factors of a link's grade is the channel load, which is
calculated from the AP's bss load element.
The current code takes this element from the beacon for an active link,
and from bss->ies for an inactive link.
bss->ies is set to either the beacon's ies or to the probe response
ones, with preference to the probe response (meaning that if there was
even one probe response, the ies of it will be stored in bss->ies and
won't be overiden by the beacon ies).
The probe response can be very old, i.e. from the connection time,
where a beacon is updated before each link selection (which is
triggered only after a passive scan).
In such case, the bss load element in the probe response will not
include the channel load caused by the STA, where the beacon will.
This will cause the inactive link to always have a lower channel
load, and therefore an higher grade than the active link's one.
This causes repeated link switches, causing the throughput to drop.
Fix this by always taking the ies from the beacon, as those are for
sure new.
Fixes: d1e879ec60 ("wifi: iwlwifi: add iwlmld sub-driver")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20251110145652.b493dbb1853a.I058ba7309c84159f640cc9682d1bda56dd56a536@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
The list_for_each_entry() iterator must not be used outside the loop.
Even though we break and check for NULL, doing so still violates kernel
iteration rules and triggers Coccinelle's use_after_iter.cocci warning.
Cache the matched entry in aux_roc_te and use it consistently after the
loop. This follows iterator best practices, resolves the warning, and
makes the code more maintainable.
Signed-off-by: Junjie Cao <junjie.cao@intel.com>
Link: https://patch.msgid.link/20251016014919.383565-1-junjie.cao@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Fix the following corner case:-
Consider a 2M huge page SVM allocation, followed by prefetch call for
the first 4K page. The whole range is initially mapped with single PTE.
After the prefetch, this range gets split to first page + rest of the
pages. Currently, the first page mapping is not updated on MI300A (APU)
since page hasn't migrated. However, after range split PTE mapping it not
valid.
Fix this by forcing page table update for the whole range when prefetch
is called. Calling prefetch on APU doesn't improve performance. If all
it deteriotes. However, functionality has to be supported.
v2: Use apu_prefer_gtt as this issue doesn't apply to APUs with carveout
VRAM
v3: Simplify by setting the flag for all ASICs as it doesn't affect dGPU
v4: Remove v2 and v3 changes. Force update_mapping when range is split
at a size that is not aligned to prange granularity
Suggested-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Philip Yang<Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 076470b9f6f8d9c7c8ca73a9f054942a686f9ba7)
Over allocation of save area is not fatal, only under allocation is.
ROCm has various components that independently claim authority over save
area size.
Unless KFD decides to claim single authority, relax size checks.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Philip Yang <philip.yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 15bd4958fe38e763bc17b607ba55155254a01f55)
Cc: stable@vger.kernel.org
When the BO pointer provided to amdgpu_bo_create_kernel() points to
non-NULL, amdgpu_bo_create_kernel() takes it as a hint to pin that address
rather than allocate a new BO.
This functionality is never desired for allocating ISP buffers. A new BO
should always be created when isp_kernel_buffer_alloc() is called, per the
description for isp_kernel_buffer_alloc().
Ensure this by zeroing *bo right before the amdgpu_bo_create_kernel() call.
Fixes: 55d42f6169 ("drm/amd/amdgpu: Add helper functions for isp buffers")
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Reviewed-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 73c8c29baac7f0c7e703d92eba009008cbb5228e)
[Why]
When changing resolution (e.g., 4K → FHD) in mirror/clone mode with
certain monitors, the monitor blanks and loses connection due to an early
exit in vrr_settings_require_update(). The function only checks if VRR
state, fixed refresh target, or min/max refresh rate range has changed.
During mode changes, if the calculated min/max refresh values remain the
same even though the stream's v_total changed, the function returns early
without updating vrr_params.adjust.v_total_min/max, leaving the monitor's
VRR timing parameters unsynced with the new mode, causing it to blank out.
[How]
Explicitly adjust VRR parameters to the stream's nominal v_total when VRR
is supported, but inactive.
Fixes: 6d31602a9f ("drm/amd/display: more liberal vmin/vmax update for freesync")
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 607df8248a011524211ee34850345305a1913f9e)
Fix a potential deadlock caused by inconsistent spinlock usage
between interrupt and process contexts in the userq fence driver.
The issue occurs when amdgpu_userq_fence_driver_process() is called
from both:
- Interrupt context: gfx_v11_0_eop_irq() -> amdgpu_userq_fence_driver_process()
- Process context: amdgpu_eviction_fence_suspend_worker() ->
amdgpu_userq_fence_driver_force_completion() -> amdgpu_userq_fence_driver_process()
In interrupt context, the spinlock was acquired without disabling
interrupts, leaving it in {IN-HARDIRQ-W} state. When the same lock
is acquired in process context, the kernel detects inconsistent
locking since the process context acquisition would enable interrupts
while holding a lock previously acquired in interrupt context.
Kernel log shows:
[ 4039.310790] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[ 4039.310804] kworker/7:2/409 [HC0[0]:SC0[0]:HE1:SE1] takes:
[ 4039.310818] ffff9284e1bed000 (&fence_drv->fence_list_lock){?...}-{3:3},
[ 4039.310993] {IN-HARDIRQ-W} state was registered at:
[ 4039.311004] lock_acquire+0xc6/0x300
[ 4039.311018] _raw_spin_lock+0x39/0x80
[ 4039.311031] amdgpu_userq_fence_driver_process.part.0+0x30/0x180 [amdgpu]
[ 4039.311146] amdgpu_userq_fence_driver_process+0x17/0x30 [amdgpu]
[ 4039.311257] gfx_v11_0_eop_irq+0x132/0x170 [amdgpu]
Fix by using spin_lock_irqsave()/spin_unlock_irqrestore() to properly
manage interrupt state regardless of calling context.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit ded3ad780cf97a04927773c4600823b84f7f3cc2)
Cc: stable@vger.kernel.org
drm_sched_entity_init wasn't called yet, so the only thing to
do is to release allocated memory.
This doesn't fix any bug since entity is zero allocated and
drm_sched_entity_fini does nothing in this case.
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit ec49374ccb8da86b465beaf09c367f3dfd648d8f)
Certain multi-GPU configurations (especially GFX12) may hit
data corruption when a DCC-compressed VRAM surface is shared across GPUs
using peer-to-peer (P2P) DMA transfers.
Such surfaces rely on device-local metadata and cannot be safely accessed
through a remote GPU’s page tables. Attempting to import a DCC-enabled
surface through P2P leads to incorrect rendering or GPU faults.
This change disables P2P for DCC-enabled VRAM buffers that are contiguous
and allocated on GFX12+ hardware. In these cases, the importer falls back
to the standard system-memory path, avoiding invalid access to compressed
surfaces.
Future work could consider optional migration (VRAM→System→VRAM) if a
performance regression is observed when `attach->peer2peer = false`.
Tested on:
- Dual RX 9700 XT (Navi4x) setup
- GNOME and Wayland compositor scenarios
- Confirmed no corruption after disabling P2P under these conditions
v2: Remove check TTM_PL_VRAM & TTM_PL_FLAG_CONTIGUOUS.
v3: simplify for upsteam and fix ip version check (Alex)
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 9dff2bb709e6fbd97e263fd12bf12802d2b5a0cf)
Cc: stable@vger.kernel.org
After commit 100dfa74cad9 ("inet: dev_queue_xmit() llist adoption")
I started seeing many qdisc requeues on IDPF under high TX workload.
$ tc -s qd sh dev eth1 handle 1: ; sleep 1; tc -s qd sh dev eth1 handle 1:
qdisc mq 1: root
Sent 43534617319319 bytes 268186451819 pkt (dropped 0, overlimits 0 requeues 3532840114)
backlog 1056Kb 6675p requeues 3532840114
qdisc mq 1: root
Sent 43554665866695 bytes 268309964788 pkt (dropped 0, overlimits 0 requeues 3537737653)
backlog 781164b 4822p requeues 3537737653
This is caused by try_bulk_dequeue_skb() being only limited by BQL budget.
perf record -C120-239 -e qdisc:qdisc_dequeue sleep 1 ; perf script
...
netperf 75332 [146] 2711.138269: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1292 skbaddr=0xff378005a1e9f200
netperf 75332 [146] 2711.138953: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1213 skbaddr=0xff378004d607a500
netperf 75330 [144] 2711.139631: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1233 skbaddr=0xff3780046be20100
netperf 75333 [147] 2711.140356: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1093 skbaddr=0xff37800514845b00
netperf 75337 [151] 2711.141037: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1353 skbaddr=0xff37800460753300
netperf 75337 [151] 2711.141877: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1367 skbaddr=0xff378004e72c7b00
netperf 75330 [144] 2711.142643: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1202 skbaddr=0xff3780045bd60000
...
This is bad because :
1) Large batches hold one victim cpu for a very long time.
2) Driver often hit their own TX ring limit (all slots are used).
3) We call dev_requeue_skb()
4) Requeues are using a FIFO (q->gso_skb), breaking qdisc ability to
implement FQ or priority scheduling.
5) dequeue_skb() gets packets from q->gso_skb one skb at a time
with no xmit_more support. This is causing many spinlock games
between the qdisc and the device driver.
Requeues were supposed to be very rare, lets keep them this way.
Limit batch sizes to /proc/sys/net/core/dev_weight (default 64) as
__qdisc_run() was designed to use.
Fixes: 5772e9a346 ("qdisc: bulk dequeue support for qdiscs with TCQ_F_ONETXQUEUE")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://patch.msgid.link/20251109161215.2574081-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
selftests: mptcp: join: fix some flaky tests
When looking at the recent CI results on NIPA and MPTCP CIs, a few MPTCP
Join tests are marked as unstable. Here are some fixes for that.
- Patch 1: a small fix for mptcp_connect.sh, printing a note as
initially intended. For >=v5.13.
- Patch 2: avoid unexpected reset when closing subflows. For >= 5.13.
- Patches 3-4: longer transfer when not waiting for the end. For >=5.18.
- Patch 5: read all received data when expecting a reset. For >= v6.1.
- Patch 6: a fix to properly kill background tasks. For >= v6.5.
====================
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-0-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'run_tests' function is executed in the background, but killing its
associated PID would not kill the children tasks running in the
background.
To properly kill all background tasks, 'kill -- -PID' could be used, but
this requires kill from procps-ng. Instead, all children tasks are
listed using 'ps', and 'kill' is called with all PIDs of this group.
Fixes: 31ee4ad86a ("selftests: mptcp: join: stop transfer when check is done (part 1)")
Cc: stable@vger.kernel.org
Fixes: 04b57c9e09 ("selftests: mptcp: join: stop transfer when check is done (part 2)")
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-6-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MPTCP Join "fastclose server" selftest is sometimes failing because the
client output file doesn't have the expected size, e.g. 296B instead of
1024B.
When looking at a packet trace when this happens, the server sent the
expected 1024B in two parts -- 100B, then 924B -- then the MP_FASTCLOSE.
It is then strange to see the client only receiving 296B, which would
mean it only got a part of the second packet. The problem is then not on
the networking side, but rather on the data reception side.
When mptcp_connect is launched with '-f -1', it means the connection
might stop before having sent everything, because a reset has been
received. When this happens, the program was directly stopped. But it is
also possible there are still some data to read, simply because the
previous 'read' step was done with a buffer smaller than the pending
data, see do_rnd_read(). In this case, it is important to read what's
left in the kernel buffers before stopping without error like before.
SIGPIPE is now ignored, not to quit the app before having read
everything.
Fixes: 6bf41020b7 ("selftests: mptcp: update and extend fastclose test-cases")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-5-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In rare cases, when the test environment is very slow, some userspace
tests can fail because some expected events have not been seen.
Because the tests are expecting a long on-going connection, and they are
not waiting for the end of the transfer, it is fine to make the
connection longer. This connection will be killed at the end, after the
verifications, so making it longer doesn't change anything, apart from
avoid it to end before the end of the verifications
To play it safe, all userspace tests not waiting for the end of the
transfer are now sharing a longer file (128KB) at slow speed.
Fixes: 4369c198e5 ("selftests: mptcp: test userspace pm out of transfer")
Cc: stable@vger.kernel.org
Fixes: b2e2248f36 ("selftests: mptcp: userspace pm create id 0 subflow")
Fixes: e3b47e460b ("selftests: mptcp: userspace pm remove initial subflow")
Fixes: b9fb176081 ("selftests: mptcp: userspace pm send RM_ADDR for ID 0")
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-4-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In rare cases, when the test environment is very slow, some userspace
tests can fail because some expected events have not been seen.
Because the tests are expecting a long on-going connection, and they are
not waiting for the end of the transfer, it is fine to make the
connection longer. This connection will be killed at the end, after the
verifications, so making it longer doesn't change anything, apart from
avoid it to end before the end of the verifications
To play it safe, all endpoints tests not waiting for the end of the
transfer are now sharing a longer file (128KB) at slow speed.
Fixes: 69c6ce7b6e ("selftests: mptcp: add implicit endpoint test case")
Cc: stable@vger.kernel.org
Fixes: e274f71540 ("selftests: mptcp: add subflow limits test-cases")
Fixes: b5e2fb832f ("selftests: mptcp: add explicit test case for remove/readd")
Fixes: e06959e9ee ("selftests: mptcp: join: test for flush/re-add endpoints")
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-3-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some of these 'remove' tests rarely fail because a subflow has been
reset instead of cleanly removed. This can happen when one extra subflow
which has never carried data is being closed (FIN) on one side, while
the other is sending data for the first time.
To avoid such subflows to be used right at the end, the backup flag has
been added. With that, data will be only carried on the initial subflow.
Fixes: d2c4333a80 ("selftests: mptcp: add testcases for removing addrs")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-2-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "fallback due to TCP OoO" was never printed because the stat_ooo_now
variable was checked twice: once in the parent if-statement, and one in
the child one. The second condition was then always true then, and the
'else' branch was never taken.
The idea is that when there are more ACK + MP_CAPABLE than expected, the
test either fails if there was no out of order packets, or a notice is
printed.
Fixes: 69ca3d29a7 ("mptcp: update selftest for fallback due to OoO")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-1-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- hci_conn: Fix not cleaning up PA_LINK connections
- hci_event: Fix not handling PA Sync Lost event
- MGMT: cancel mesh send timer when hdev removed
- 6lowpan: reset link-local header on ipv6 recv path
- 6lowpan: fix BDADDR_LE vs ADDR_LE_DEV address type confusion
- L2CAP: export l2cap_chan_hold for modules
- 6lowpan: Don't hold spin lock over sleeping functions
- 6lowpan: add missing l2cap_chan_lock()
- btusb: reorder cleanup in btusb_disconnect to avoid UAF
- btrtl: Avoid loading the config file on security chips
* tag 'for-net-2025-11-11' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: btrtl: Avoid loading the config file on security chips
Bluetooth: hci_event: Fix not handling PA Sync Lost event
Bluetooth: hci_conn: Fix not cleaning up PA_LINK connections
Bluetooth: 6lowpan: add missing l2cap_chan_lock()
Bluetooth: 6lowpan: Don't hold spin lock over sleeping functions
Bluetooth: L2CAP: export l2cap_chan_hold for modules
Bluetooth: 6lowpan: fix BDADDR_LE vs ADDR_LE_DEV address type confusion
Bluetooth: 6lowpan: reset link-local header on ipv6 recv path
Bluetooth: btusb: reorder cleanup in btusb_disconnect to avoid UAF
Bluetooth: MGMT: cancel mesh send timer when hdev removed
====================
Link: https://patch.msgid.link/20251111141357.1983153-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Building documentation produced the following warning:
WARNING: ./include/linux/ethtool.h:495 This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* IEEE 802.3ck/df defines 16 bins for FEC histogram plus one more for
This comment was not intended to be parsed as kernel-doc, so replace
the '/**' with '/*' to silence the warning and align with normal
comment style in header files.
No functional changes.
Signed-off-by: Kriish Sharma <kriish.sharma2006@gmail.com>
Link: https://patch.msgid.link/20251110182545.2112596-1-kriish.sharma2006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Starting with Rust 1.91.0 (released 2025-10-30), in upstream commit
ab91a63d403b ("Ignore intrinsic calls in cross-crate-inlining cost model")
[1][2], `bindings.o` stops containing DWARF debug information because the
`Default` implementations contained `write_bytes()` calls which are now
ignored in that cost model (note that `CLIPPY=1` does not reproduce it).
This means `gendwarfksyms` complains:
RUSTC L rust/bindings.o
error: gendwarfksyms: process_module: dwarf_get_units failed: no debugging information?
There are several alternatives that would work here: conditionally
skipping in the cases needed (but that is subtle and brittle), forcing
DWARF generation with e.g. a dummy `static` (ugly and we may need to
do it in several crates), skipping the call to the tool in the Kbuild
command when there are no exports (fine) or teaching the tool to do so
itself (simple and clean).
Thus do the last one: don't attempt to process files if we have no symbol
versions to calculate.
[ I used the commit log of my patch linked below since it explained the
root issue and expanded it a bit more to summarize the alternatives.
- Miguel ]
Cc: stable@vger.kernel.org # Needed in 6.17.y.
Reported-by: Haiyue Wang <haiyuewa@163.com>
Closes: https://lore.kernel.org/rust-for-linux/b8c1c73d-bf8b-4bf2-beb1-84ffdcd60547@163.com/
Suggested-by: Miguel Ojeda <ojeda@kernel.org>
Link: https://lore.kernel.org/rust-for-linux/CANiq72nKC5r24VHAp9oUPR1HVPqT+=0ab9N0w6GqTF-kJOeiSw@mail.gmail.com/
Link: ab91a63d40 [1]
Link: https://github.com/rust-lang/rust/pull/145910 [2]
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Haiyue Wang <haiyuewa@163.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://patch.msgid.link/20251110131913.1789896-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Pull arm64 fixes from Will Deacon:
"There's more here than I would ideally like at this stage, but there's
been a steady trickle of fixes and some of them took a few rounds of
review.
The bulk of the changes are fixing some fallout from the recent BBM
level two support which allows the linear map to be split from block
to page mappings at runtime, but inadvertently led to sleeping in
atomic context on some paths where the linear map was already mapped
with page granularity. The fix is simply to avoid splitting in those
cases but the implementation of that is a little involved.
The other interesting fix is addressing a catastophic performance
issue with our per-cpu atomics discovered by Paul in the SRCU locking
code but which took some interactions with the hardware folks to
resolve.
Summary:
- Avoid sleeping in atomic context when changing linear map
permissions for DEBUG_PAGEALLOC or KFENCE
- Rework printing of Spectre mitigation status to avoid hardlockup
when enabling per-task mitigations on the context-switch path
- Reject kernel modules when instruction patching fails either due to
the DWARF-based SCS patching or because of an alternatives callback
residing outside of the core kernel text
- Propagate error when updating kernel memory permissions in kprobes
- Drop pointless, incorrect message when enabling the ACPI SPCR
console
- Use value-returning LSE instructions for per-cpu atomics to reduce
latency in SRCU locking routines"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Reject modules with internal alternative callbacks
arm64: Fail module loading if dynamic SCS patching fails
arm64: proton-pack: Fix hard lockup due to print in scheduler context
arm64: proton-pack: Drop print when !CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
arm64: mm: Tidy up force_pte_mapping()
arm64: mm: Optimize range_split_to_ptes()
arm64: mm: Don't sleep in split_kernel_leaf_mapping() when in atomic context
arm64: kprobes: check the return value of set_memory_rox()
arm64: acpi: Drop message logging SPCR default console
Revert "ACPI: Suppress misleading SPCR console message when SPCR table is absent"
arm64: Use load LSE atomics for the non-return per-CPU atomic operations
Pull btrfs fixes from David Sterba:
- fix new inode name tracking in tree-log
- fix conventional zone and stripe calculations in zoned mode
- fix bio reference counts on error paths in relocation and scrub
* tag 'for-6.18-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: release root after error in data_reloc_print_warning_inode()
btrfs: scrub: put bio after errors in scrub_raid56_parity_stripe()
btrfs: do not update last_log_commit when logging inode due to a new name
btrfs: zoned: fix stripe width calculation
btrfs: zoned: fix conventional zone capacity calculation
Pull misc fixes from Andrew Morton:
"26 hotfixes. 22(!) are cc:stable, 22 are MM.
- address some Kexec Handover issues (Pasha Tatashin)
- fix handling of large folios which are mapped outside i_size (Kiryl
Shutsemau)
- fix some DAMON time issues on 32-bit machines (Quanmin Yan)
Plus the usual shower of singletons"
* tag 'mm-hotfixes-stable-2025-11-10-19-30' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (26 commits)
kho: warn and exit when unpreserved page wasn't preserved
kho: fix unpreservation of higher-order vmalloc preservations
kho: fix out-of-bounds access of vmalloc chunk
MAINTAINERS: add Chris and Kairui as the swap maintainer
mm/secretmem: fix use-after-free race in fault handler
mm/huge_memory: initialise the tags of the huge zero folio
nilfs2: avoid having an active sc_timer before freeing sci
scripts/decode_stacktrace.sh: fix build ID and PC source parsing
mm/damon/sysfs: change next_update_jiffies to a global variable
mm/damon/stat: change last_refresh_jiffies to a global variable
maple_tree: fix tracepoint string pointers
codetag: debug: handle existing CODETAG_EMPTY in mark_objexts_empty for slabobj_ext
mm/mremap: honour writable bit in mremap pte batching
gcov: add support for GCC 15
mm/mm_init: fix hash table order logging in alloc_large_system_hash()
mm/truncate: unmap large folio on split failure
mm/memory: do not populate page table entries beyond i_size
fs/proc: fix uaf in proc_readdir_de()
mm/huge_memory: preserve PG_has_hwpoisoned if a folio is split to >0 order
ksm: use range-walk function to jump over holes in scan_get_next_rmap_item
...
When smbd_disconnect_rdma_connection() turns SMBDIRECT_SOCKET_CREATED
into SMBDIRECT_SOCKET_ERROR, we'll have the situation that
smbd_disconnect_rdma_work() will set SMBDIRECT_SOCKET_DISCONNECTING
and call rdma_disconnect(), which likely fails as we never reached
the RDMA_CM_EVENT_ESTABLISHED. it means that
wait_event(sc->status_wait, sc->status == SMBDIRECT_SOCKET_DISCONNECTED)
in smbd_destroy() will hang forever in SMBDIRECT_SOCKET_DISCONNECTING
never reaching SMBDIRECT_SOCKET_DISCONNECTED.
So we directly go from SMBDIRECT_SOCKET_CREATED to
SMBDIRECT_SOCKET_DISCONNECTED.
Fixes: ffbfc73e84 ("smb: client: let smbd_disconnect_rdma_connection() set SMBDIRECT_SOCKET_ERROR...")
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
In snd_usb_create_streams(), for UAC version 3 devices, the Interface
Association Descriptor (IAD) is retrieved via usb_ifnum_to_if(). If this
call fails, a fallback routine attempts to obtain the IAD from the next
interface and sets a BADD profile. However, snd_usb_mixer_controls_badd()
assumes that the IAD retrieved from usb_ifnum_to_if() is always valid,
without performing a NULL check. This can lead to a NULL pointer
dereference when usb_ifnum_to_if() fails to find the interface descriptor.
This patch adds a NULL pointer check after calling usb_ifnum_to_if() in
snd_usb_mixer_controls_badd() to prevent the dereference.
This issue was discovered by syzkaller, which triggered the bug by sending
a crafted USB device descriptor.
Fixes: 17156f23e9 ("ALSA: usb: add UAC3 BADD profiles support")
Signed-off-by: Haein Lee <lhi0729@kaist.ac.kr>
Link: https://patch.msgid.link/vwhzmoba9j2f.vwhzmob9u9e2.g6@dooray.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ciu clock is 2 times of io clock, but the sample clk used is
derived from io clock provided to the card. So we should use
io clock to calculate the phase.
Fixes: 59903441f5 ("mmc: dw_mmc-rockchip: Add internal phase support")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
memblock_estimated_nr_free_pages() returns the difference between the total
size of the "memory" memblock type and the "reserved" memblock type.
The "soft-reserved" memory regions are added to the "reserved" memblock
type, but not to the "memory" memblock type. Therefore,
memblock_estimated_nr_free_pages() may return a smaller value than
expected, or if it underflows, an extremely large value.
/proc/sys/kernel/threads-max is determined by the value of
memblock_estimated_nr_free_pages(). This issue was discovered on machines
with CXL memory because kernel.threads-max was either smaller than expected
or extremely large for the installed DRAM size.
This fixes the issue by replacing memblock_reserved_size() with
memblock_reserved_kern_size() that tells how much memory was
reserved from the actual RAM.
Suggested-by: Mike Rapoport <rppt@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Link: https://patch.msgid.link/20251111010010.7800-1-akinobu.mita@gmail.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Since the maximum return value of strnlen(..., CIFS_MAX_USERNAME_LEN)
is CIFS_MAX_USERNAME_LEN, length check in smb3_fs_context_parse_param()
is always FALSE and invalid.
Fix the comparison in if statement.
Signed-off-by: Yiqi Sun <sunyiqixm@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
When smb_direct_disconnect_rdma_connection() turns SMBDIRECT_SOCKET_CREATED
into SMBDIRECT_SOCKET_ERROR, we'll have the situation that
smb_direct_disconnect_rdma_work() will set SMBDIRECT_SOCKET_DISCONNECTING
and call rdma_disconnect(), which likely fails as we never reached
the RDMA_CM_EVENT_ESTABLISHED. it means that
wait_event(sc->status_wait, sc->status == SMBDIRECT_SOCKET_DISCONNECTED)
in free_transport() will hang forever in SMBDIRECT_SOCKET_DISCONNECTING
never reaching SMBDIRECT_SOCKET_DISCONNECTED.
So we directly go from SMBDIRECT_SOCKET_CREATED to
SMBDIRECT_SOCKET_DISCONNECTED.
Fixes: b3fd52a0d8 ("smb: server: let smb_direct_disconnect_rdma_connection() set SMBDIRECT_SOCKET_ERROR...")
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Currently, CQs without a completion function are assigned the
mlx5_add_cq_to_tasklet function by default. This is problematic since
only user CQs created through the mlx5_ib driver are intended to use
this function.
Additionally, all CQs that will use doorbells instead of polling for
completions must call mlx5_cq_arm. However, the default CQ creation flow
leaves a valid value in the CQ's arm_db field, allowing FW to send
interrupts to polling-only CQs in certain corner cases.
These two factors would allow a polling-only kernel CQ to be triggered
by an EQ interrupt and call a completion function intended only for user
CQs, causing a null pointer exception.
Some areas in the driver have prevented this issue with one-off fixes
but did not address the root cause.
This patch fixes the described issue by adding defaults to the create CQ
flow. It adds a default dummy completion function to protect against
null pointer exceptions, and it sets an invalid command sequence number
by default in kernel CQs to prevent the FW from sending an interrupt to
the CQ until it is armed. User CQs are responsible for their own
initialization values.
Callers of mlx5_core_create_cq are responsible for changing the
completion function and arming the CQ per their needs.
Fixes: cdd04f4d4d ("net/mlx5: Add support to create SQ and CQ for ASO")
Signed-off-by: Akiva Goldberger <agoldberger@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Acked-by: Leon Romanovsky <leon@kernel.org>
Link: https://patch.msgid.link/1762681743-1084694-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For chips with security enabled, it's only possible to load firmware
with a valid signature pattern.
If key_id is not zero, it indicates a security chip, and the driver will
not load the config file.
- Example log for a security chip.
Bluetooth: hci0: RTL: examining hci_ver=0c hci_rev=000a
lmp_ver=0c lmp_subver=8922
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: btrtl_initialize: key id 1
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_fw.bin
Bluetooth: hci0: RTL: cfg_sz 0, total sz 71301
Bluetooth: hci0: RTL: fw version 0x41c0c905
- Example log for a normal chip.
Bluetooth: hci0: RTL: examining hci_ver=0c hci_rev=000a
lmp_ver=0c lmp_subver=8922
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: btrtl_initialize: key id 0
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_fw.bin
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_config.bin
Bluetooth: hci0: RTL: cfg_sz 6, total sz 71307
Bluetooth: hci0: RTL: fw version 0x41c0c905
Tested-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Nial Ni <niall_ni@realsil.com.cn>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The previous calculation used roundup() which caused an overflow for
rates between 25.5Gbps and 26Gbps.
For example, a rate of 25.6Gbps would result in using 100Mbps units with
value of 256, which would overflow the 8 bits field.
Simplify the upper_limit_mbps calculation by removing the
unnecessary roundup, and adjust the comparison to use <= to correctly
handle the boundary condition.
Fixes: d8880795da ("net/mlx5e: Implement DCBNL IEEE max rate")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1762681073-1084058-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The current single-bit error injection mechanism flips bits directly in ECC RAM
by performing write and read operations. When the ECC RAM is actively used by
the Ethernet or USB controller, this approach sometimes trigger a false
double-bit error.
Switch both Ethernet and USB EDAC devices to use the INTTEST register
(altr_edac_a10_device_inject_fops) for single-bit error injection, similar to
the existing double-bit error injection method.
Fixes: 064acbd4f4 ("EDAC, altera: Add Stratix10 peripheral support")
Signed-off-by: Niravkumar L Rabara <niravkumarlaxmidas.rabara@altera.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251111081333.1279635-1-niravkumarlaxmidas.rabara@altera.com
This handles PA Sync Lost event which previously was assumed to be
handled with BIG Sync Lost but their lifetime are not the same thus why
there are 2 different events to inform when each sync is lost.
Fixes: b2a5f2e1c1 ("Bluetooth: hci_event: Add support for handling LE BIG Sync Lost event")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Quang Le reported that the AF_UNIX GC could garbage-collect a
receive queue of an alive in-flight socket, with a nice repro.
The repro consists of three stages.
1)
1-a. Create a single cyclic reference with many sockets
1-b. close() all sockets
1-c. Trigger GC
2)
2-a. Pass sk-A to an embryo sk-B
2-b. Pass sk-X to sk-X
2-c. Trigger GC
3)
3-a. accept() the embryo sk-B
3-b. Pass sk-B to sk-C
3-c. close() the in-flight sk-A
3-d. Trigger GC
As of 2-c, sk-A and sk-X are linked to unix_unvisited_vertices,
and unix_walk_scc() groups them into two different SCCs:
unix_sk(sk-A)->vertex->scc_index = 2 (UNIX_VERTEX_INDEX_START)
unix_sk(sk-X)->vertex->scc_index = 3
Once GC completes, unix_graph_grouped is set to true.
Also, unix_graph_maybe_cyclic is set to true due to sk-X's
cyclic self-reference, which makes close() trigger GC.
At 3-b, unix_add_edge() allocates unix_sk(sk-B)->vertex and
links it to unix_unvisited_vertices.
unix_update_graph() is called at 3-a. and 3-b., but neither
unix_graph_grouped nor unix_graph_maybe_cyclic is changed
because both sk-B's listener and sk-C are not in-flight.
3-c decrements sk-A's file refcnt to 1.
Since unix_graph_grouped is true at 3-d, unix_walk_scc_fast()
is finally called and iterates 3 sockets sk-A, sk-B, and sk-X:
sk-A -> sk-B (-> sk-C)
sk-X -> sk-X
This is totally fine. All of them are not yet close()d and
should be grouped into different SCCs.
However, unix_vertex_dead() misjudges that sk-A and sk-B are
in the same SCC and sk-A is dead.
unix_sk(sk-A)->scc_index == unix_sk(sk-B)->scc_index <-- Wrong!
&&
sk-A's file refcnt == unix_sk(sk-A)->vertex->out_degree
^-- 1 in-flight count for sk-B
-> sk-A is dead !?
The problem is that unix_add_edge() does not initialise scc_index.
Stage 1) is used for heap spraying, making a newly allocated
vertex have vertex->scc_index == 2 (UNIX_VERTEX_INDEX_START)
set by unix_walk_scc() at 1-c.
Let's track the max SCC index from the previous unix_walk_scc()
call and assign the max + 1 to a new vertex's scc_index.
This way, we can continue to avoid Tarjan's algorithm while
preventing misjudgments.
Fixes: ad081928a8 ("af_unix: Avoid Tarjan's algorithm if unnecessary.")
Reported-by: Quang Le <quanglex97@gmail.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20251109025233.3659187-1-kuniyu@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In fact, it is a multi-threaded MIPS34Kc, not a single-threaded MIPS24Kc.
Fixes: 0ec4887009 ("mips: dts: Add EcoNet DTS with EN751221 and SmartFiber XP8421-B board")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix a regression that has caused accesses to the PCI MMIO window to
complete unclaimed in non-EVA configurations with the SOC-it family of
system controllers, preventing PCI devices from working that use MMIO.
In the non-EVA case PHYS_OFFSET is set to 0, meaning that PCI_BAR0 is
set with an empty mask (and PCI_HEAD4 matches addresses starting from 0
accordingly). Consequently all addresses are matched for incoming DMA
accesses from PCI. This seems to confuse the system controller's logic
and outgoing bus cycles targeting the PCI MMIO window seem not to make
it to the intended devices.
This happens as well when a wider mask is used with PCI_BAR0, such as
0x80000000 or 0xe0000000, that makes addresses match that overlap with
the PCI MMIO window, which starts at 0x10000000 in our configuration.
Set the mask in PCI_BAR0 to 0xf0000000 for non-EVA then, covering the
non-EVA maximum 256 MiB of RAM, which is what YAMON does and which used
to work correctly up to the offending commit. Set PCI_P2SCMSKL to match
PCI_BAR0 as required by the system controller's specification, and match
PCI_P2SCMAPL to PCI_HEAD4 for identity mapping.
Verified with:
Core board type/revision = 0x0d (Core74K) / 0x01
System controller/revision = MIPS SOC-it 101 OCP / 1.3 SDR-FW-4:1
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x1c
Processor ID/revision = 0x97 (MIPS 74Kf) / 0x4c
for non-EVA and with:
Core board type/revision = 0x0c (CoreFPGA-5) / 0x00
System controller/revision = MIPS ROC-it2 / 0.0 FW-1:1 (CLK_unknown) GIC
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision = 0xa0 (MIPS interAptiv UP) / 0x20
for EVA/non-EVA, fixing:
defxx 0000:00:12.0: assign IRQ: got 10
defxx: v1.12 2021/03/10 Lawrence V. Stefani and others
0000:00:12.0: Could not read adapter factory MAC address!
vs:
defxx 0000:00:12.0: assign IRQ: got 10
defxx: v1.12 2021/03/10 Lawrence V. Stefani and others
0000:00:12.0: DEFPA at MMIO addr = 0x10142000, IRQ = 10, Hardware addr = 00-00-f8-xx-xx-xx
0000:00:12.0: registered as fddi0
for non-EVA and causing no change for EVA.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 422dd25664 ("MIPS: Malta: Allow PCI devices DMA to lower 2GB physical")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Some Marvell AP firmware used with mwl8k misbehaves when beacon frames
do not contain a WLAN_EID_DS_PARAMS element with the current channel.
It was reported on OpenWrt Github issues [0].
When hostapd/mac80211 omits DSSS Parameter Set from the beacon (which is
valid on some bands), the firmware stops transmitting sane frames and RX
status starts reporting bogus channel information. This makes AP mode
unusable.
Newer Marvell drivers (mwlwifi [1]) hard-code DSSS Parameter Set into
AP beacons for all chips, which suggests this is a firmware requirement
rather than a mwl8k-specific quirk.
Mirror that behaviour in mwl8k: when setting the beacon, check if
WLAN_EID_DS_PARAMS is present, and if not, extend the beacon and inject
a DSSS Parameter Set element, using the current channel from
hw->conf.chandef.chan.
Tested on Linksys EA4500 (88W8366).
[0] https://github.com/openwrt/openwrt/issues/19088
[1] db97edf20f/hif/fwcmd.c (L675)
Fixes: b64fe619e3 ("mwl8k: basic AP interface support")
Tested-by: Antony Kolitsos <zeusomighty@hotmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://patch.msgid.link/20251111100733.2825970-3-paweldembicki@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jeff Johnson says:
==================
ath.git update for v6.18-rc6
Fix an ath11k transmit status reporting issue. This issue has always
been present, but not reported until recently.
Bringing this through the current release since there is now a
userspace entity that wants to leverage this.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Breno Leitao says:
====================
net: netpoll: fix memory leak and add comprehensive selftests
Fix a memory leak in netpoll and introduce netconsole selftests that
expose the issue when running with kmemleak detection enabled.
This patchset includes a selftest for netpoll with multiple concurrent
users (netconsole + bonding), which simulates the scenario from test[1]
that originally demonstrated the issue allegedly fixed by commit
efa95b01da ("netpoll: fix use after free") - a commit that is now
being reverted.
Sending this to "net" branch because this is a fix, and the selftest
might help with the backports validation.
Link: https://lore.kernel.org/lkml/96b940137a50e5c387687bb4f57de8b0435a653f.1404857349.git.decot@googlers.com/ [1]
====================
Link: https://patch.msgid.link/20251107-netconsole_torture-v10-0-749227b55f63@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a netconsole test that puts a lot of pressure on the netconsole
list manipulation. Do it by creating dynamic targets and deleting
targets while messages are being sent. Also put interface down while the
messages are being sent, as creating parallel targets.
The code launches three background jobs on distinct schedules:
* Toggle netcons target every 30 iterations
* create and delete random_target every 50 iterations
* toggle iface every 70 iterations
This creates multiple concurrency sources that interact with netconsole
states. This is good practice to simulate stress, and exercise netpoll
and netconsole locks.
This test already found an issue as reported in [1]
Link: https://lore.kernel.org/all/20250901-netpoll_memleak-v1-1-34a181977dfc@debian.org/ [1]
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Andre Carvalho <asantostc@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251107-netconsole_torture-v10-3-749227b55f63@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extract the netconsole target creation from create_dynamic_target(), by
moving it from create_dynamic_target() into a new helper function. This
enables other tests to use the creation of netconsole targets with
arbitrary parameters and no sleep.
The new helper will be utilized by forthcoming torture-type selftests
that require dynamic target management.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251107-netconsole_torture-v10-2-749227b55f63@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit efa95b01da ("netpoll: fix use after free") incorrectly
ignored the refcount and prematurely set dev->npinfo to NULL during
netpoll cleanup, leading to improper behavior and memory leaks.
Scenario causing lack of proper cleanup:
1) A netpoll is associated with a NIC (e.g., eth0) and netdev->npinfo is
allocated, and refcnt = 1
- Keep in mind that npinfo is shared among all netpoll instances. In
this case, there is just one.
2) Another netpoll is also associated with the same NIC and
npinfo->refcnt += 1.
- Now dev->npinfo->refcnt = 2;
- There is just one npinfo associated to the netdev.
3) When the first netpolls goes to clean up:
- The first cleanup succeeds and clears np->dev->npinfo, ignoring
refcnt.
- It basically calls `RCU_INIT_POINTER(np->dev->npinfo, NULL);`
- Set dev->npinfo = NULL, without proper cleanup
- No ->ndo_netpoll_cleanup() is either called
4) Now the second target tries to clean up
- The second cleanup fails because np->dev->npinfo is already NULL.
* In this case, ops->ndo_netpoll_cleanup() was never called, and
the skb pool is not cleaned as well (for the second netpoll
instance)
- This leaks npinfo and skbpool skbs, which is clearly reported by
kmemleak.
Revert commit efa95b01da ("netpoll: fix use after free") and adds
clarifying comments emphasizing that npinfo cleanup should only happen
once the refcount reaches zero, ensuring stable and correct netpoll
behavior.
Cc: <stable@vger.kernel.org> # 3.17.x
Cc: Jay Vosburgh <jv@jvosburgh.net>
Fixes: efa95b01da ("netpoll: fix use after free")
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251107-netconsole_torture-v10-1-749227b55f63@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Aksh Garg says:
====================
Fix IET verification implementation for CPSW driver
The CPSW module supports Intersperse Express Traffic (IET) and allows
the MAC layer to verify whether the peer supports IET through its MAC
merge sublayer, by sending a verification packet and waiting for its
response until the timeout. As defined in IEEE 802.3 Clause 99, the
verification process involves up to 3 verification attempts to
establish support.
This patch series fixes issues in the implementation of this IET
verification process.
====================
Link: https://patch.msgid.link/20251106092305.1437347-1-a-garg7@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The am65_cpsw_iet_verify_wait() function attempts verification 20 times,
toggling the AM65_CPSW_PN_IET_MAC_LINKFAIL bit in each iteration. When
the LINKFAIL bit transitions from 1 to 0, the MAC merge layer initiates
the verification process and waits for the timeout configured in
MAC_VERIFY_CNT before automatically retransmitting. The MAC_VERIFY_CNT
register is configured according to the user-defined verify/response
timeout in am65_cpsw_iet_set_verify_timeout_count(). As per IEEE 802.3
Clause 99, the hardware performs this automatic retry up to 3 times.
Current implementation toggles LINKFAIL after the user-configured
verify/response timeout in each iteration, forcing the hardware to
restart verification instead of respecting the MAC_VERIFY_CNT timeout.
This bypasses the hardware's automatic retry mechanism.
Fix this by moving the LINKFAIL bit toggle outside the retry loop and
reducing the retry count from 20 to 3. The software now only monitors
the status register while the hardware autonomously handles the 3
verification attempts at proper MAC_VERIFY_CNT intervals.
Fixes: 49a2eb9068 ("net: ethernet: ti: am65-cpsw-qos: Add Frame Preemption MAC Merge support")
Signed-off-by: Aksh Garg <a-garg7@ti.com>
Link: https://patch.msgid.link/20251106092305.1437347-3-a-garg7@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CPSW module uses the MAC_VERIFY_CNT bit field in the
CPSW_PN_IET_VERIFY_REG_k register to set the verify/response timeout
count. This register specifies the number of clock cycles to wait before
resending a verify packet if the verification fails.
The verify/response timeout count, as being set by the function
am65_cpsw_iet_set_verify_timeout_count() is hardcoded for 125MHz
clock frequency, which varies based on PHY mode and link speed.
The respective clock frequencies are as follows:
- RGMII mode:
* 1000 Mbps: 125 MHz
* 100 Mbps: 25 MHz
* 10 Mbps: 2.5 MHz
- QSGMII/SGMII mode: 125 MHz (all speeds)
Fix this by adding logic to calculate the correct timeout counts
based on the actual PHY interface mode and link speed.
Fixes: 49a2eb9068 ("net: ethernet: ti: am65-cpsw-qos: Add Frame Preemption MAC Merge support")
Signed-off-by: Aksh Garg <a-garg7@ti.com>
Link: https://patch.msgid.link/20251106092305.1437347-2-a-garg7@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In tls_handshake_accept(), a netlink message is allocated using
genlmsg_new(). In the error handling path, genlmsg_cancel() is called
to cancel the message construction, but the message itself is not freed.
This leads to a memory leak.
Fix this by calling nlmsg_free() in the error path after genlmsg_cancel()
to release the allocated memory.
Fixes: 2fd5532044 ("net/handshake: Add a kernel API for requesting a TLSv1.3 handshake")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Link: https://patch.msgid.link/20251106144511.3859535-1-zilin@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current CLC proposal message construction uses a mix of
`ini->smc_type_v1/v2` and `pclc_base->hdr.typev1/v2` to decide whether
to include optional extensions (IPv6 prefix extension for v1, and v2
extension). This leads to a critical inconsistency: when
`smc_clc_prfx_set()` fails - for example, in IPv6-only environments with
only link-local addresses, or when the local IP address and the outgoing
interface’s network address are not in the same subnet.
As a result, the proposal message is assembled using the stale
`ini->smc_type_v1` value—causing the IPv6 prefix extension to be
included even though the header indicates v1 is not supported.
The peer then receives a malformed CLC proposal where the header type
does not match the payload, and immediately resets the connection.
The fix ensures consistency between the CLC header flags and the actual
payload by synchronizing `ini->smc_type_v1` with `pclc_base->hdr.typev1`
when prefix setup fails.
Fixes: 8c3dca341a ("net/smc: build and send V2 CLC proposal")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://patch.msgid.link/20251107024029.88753-1-alibuda@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When freeing indexed arrays, the corresponding free function should
be called for each entry of the indexed array. For example, for
for 'struct tc_act_attrs' 'tc_act_attrs_free(...)' needs to be called
for each entry.
Previously, memory leaks were reported when enabling the ASAN
analyzer.
=================================================================
==874==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 24 byte(s) in 1 object(s) allocated from:
#0 0x7f221fd20cb5 in malloc ./debug/gcc/gcc/libsanitizer/asan/asan_malloc_linux.cpp:67
#1 0x55c98db048af in tc_act_attrs_set_options_vlan_parms ../generated/tc-user.h:2813
#2 0x55c98db048af in main ./linux/tools/net/ynl/samples/tc-filter-add.c:71
Direct leak of 24 byte(s) in 1 object(s) allocated from:
#0 0x7f221fd20cb5 in malloc ./debug/gcc/gcc/libsanitizer/asan/asan_malloc_linux.cpp:67
#1 0x55c98db04a93 in tc_act_attrs_set_options_vlan_parms ../generated/tc-user.h:2813
#2 0x55c98db04a93 in main ./linux/tools/net/ynl/samples/tc-filter-add.c:74
Direct leak of 10 byte(s) in 2 object(s) allocated from:
#0 0x7f221fd20cb5 in malloc ./debug/gcc/gcc/libsanitizer/asan/asan_malloc_linux.cpp:67
#1 0x55c98db0527d in tc_act_attrs_set_kind ../generated/tc-user.h:1622
SUMMARY: AddressSanitizer: 58 byte(s) leaked in 4 allocation(s).
The following diff illustrates the changes introduced compared to the
previous version of the code.
void tc_flower_attrs_free(struct tc_flower_attrs *obj)
{
+ unsigned int i;
+
free(obj->indev);
+ for (i = 0; i < obj->_count.act; i++)
+ tc_act_attrs_free(&obj->act[i]);
free(obj->act);
free(obj->key_eth_dst);
free(obj->key_eth_dst_mask);
Signed-off-by: Zahari Doychev <zahari.doychev@linux.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20251106151529.453026-3-zahari.doychev@linux.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Broadcom switches locally terminate link local traffic and do not
forward it, so we should not mark it as offloaded.
In some situations we still want/need to flood this traffic, e.g. if STP
is disabled, or it is explicitly enabled via the group_fwd_mask. But if
the skb is marked as offloaded, the kernel will assume this was already
done in hardware, and the packets never reach other bridge ports.
So ensure that link local traffic is never marked as offloaded, so that
the kernel can forward/flood these packets in software if needed.
Since the local termination in not configurable, check the destination
MAC, and never mark packets as offloaded if it is a link local ether
address.
While modern switches set the tag reason code to BRCM_EG_RC_PROT_TERM
for trapped link local traffic, they also set it for link local traffic
that is flooded (01:80:c2:00:00:10 to 01:80:c2:00:00:2f), so we cannot
use it and need to look at the destination address for them as well.
Fixes: 964dbf186e ("net: dsa: tag_brcm: add support for legacy tags")
Fixes: 0e62f543be ("net: dsa: Fix duplicate frames flooded by learning")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251109134635.243951-1-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The tracing selftest "event-filter-function.tc" was failing because it
first runs the "sample_events" function that triggers the kmem_cache_free
event and it looks at what function was used during a call to "ls".
But the first time it calls this, it could trigger events that are used to
pull pages into the page cache.
The rest of the test uses the function it finds during that call to see if
it will be called in subsequent "sample_events" calls. But if there's no
need to pull pages into the page cache, it will not trigger that function
and the test will fail.
Call the "sample_events" twice to trigger all the page cache work before
it calls it to find a function to use in subsequent checks.
Cc: stable@vger.kernel.org
Fixes: eb50d0f250 ("selftests/ftrace: Choose target function for filter test from samples")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
syzbot reported a possible shift-out-of-bounds [1]
Blamed commit added rto_alpha_max and rto_beta_max set to 1000.
It is unclear if some sctp users are setting very large rto_alpha
and/or rto_beta.
In order to prevent user regression, perform the test at run time.
Also add READ_ONCE() annotations as sysctl values can change under us.
[1]
UBSAN: shift-out-of-bounds in net/sctp/transport.c:509:41
shift exponent 64 is too large for 32-bit type 'unsigned int'
CPU: 0 UID: 0 PID: 16704 Comm: syz.2.2320 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/02/2025
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x16c/0x1f0 lib/dump_stack.c:120
ubsan_epilogue lib/ubsan.c:233 [inline]
__ubsan_handle_shift_out_of_bounds+0x27f/0x420 lib/ubsan.c:494
sctp_transport_update_rto.cold+0x1c/0x34b net/sctp/transport.c:509
sctp_check_transmitted+0x11c4/0x1c30 net/sctp/outqueue.c:1502
sctp_outq_sack+0x4ef/0x1b20 net/sctp/outqueue.c:1338
sctp_cmd_process_sack net/sctp/sm_sideeffect.c:840 [inline]
sctp_cmd_interpreter net/sctp/sm_sideeffect.c:1372 [inline]
Fixes: b58537a1f5 ("net: sctp: fix permissions for rto_alpha and rto_beta knobs")
Reported-by: syzbot+f8c46c8b2b7f6e076e99@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/690c81ae.050a0220.3d0d33.014e.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20251106111054.3288127-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull RISC-V fixes from Paul Walmsley:
- fix broken clang build on versions earlier than 19 and binutils
versions earlier than 2.38.
(This exposed that we're not properly testing earlier toolchain
versions in our linux-next builds and PR submissions. This was fixed
for this PR, and is being addressed more generally for -next builds.)
- remove some redundant Makefile code
- avoid building Canaan Kendryte K210-specific code on targets that
don't build for the K210
* tag 'riscv-for-linus-6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix CONFIG_AS_HAS_INSN for new .insn usage
riscv: Remove redundant judgment for the default build target
riscv: Build loader.bin exclusively for Canaan K210
It's useful to know which query opcodes are available. Extend the
structure and return that. It's a trivial change, and even though it can
be painlessly extended later, it'd still require adding a v2 of the
structure.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The utimes01 and utime06 tests fail when delegated timestamps are
enabled, specifically in subtests that modify the atime and mtime
fields using the 'nobody' user ID.
The problem can be reproduced as follow:
# echo "/media *(rw,no_root_squash,sync)" >> /etc/exports
# export -ra
# mount -o rw,nfsvers=4.2 127.0.0.1:/media /tmpdir
# cd /opt/ltp
# ./runltp -d /tmpdir -s utimes01
# ./runltp -d /tmpdir -s utime06
This issue occurs because nfs_setattr does not verify the inode's
UID against the caller's fsuid when delegated timestamps are
permitted for the inode.
This patch adds the UID check and if it does not match then the
request is sent to the server for permission checking.
Fixes: e12912d941 ("NFSv4: Add support for delegated atime and mtime attributes")
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
Contrary to what was stated on d36349ea73 ("Bluetooth: hci_conn:
Fix running bis_cleanup for hci_conn->type PA_LINK") the PA_LINK does
in fact needs to run bis_cleanup in order to terminate the PA Sync,
since that is bond to the listening socket which is the entity that
controls the lifetime of PA Sync, so if it is closed/released the PA
Sync shall be terminated, terminating the PA Sync shall not result in
the BIG Sync being terminated since once the later is established it
doesn't depend on the former anymore.
If the use user wants to reconnect/rebind a number of BIS(s) it shall
keep the socket open until it no longer needs the PA Sync, which means
it retains full control of the lifetime of both PA and BIG Syncs.
Fixes: d36349ea73 ("Bluetooth: hci_conn: Fix running bis_cleanup for hci_conn->type PA_LINK")
Fixes: a7bcffc673 ("Bluetooth: Add PA_LINK to distinguish BIG sync and PA sync connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
l2cap_chan_close() needs to be called in l2cap_chan_lock(), otherwise
l2cap_le_sig_cmd() etc. may run concurrently.
Add missing locks around l2cap_chan_close().
Fixes: 6b8d4a6a03 ("Bluetooth: 6LoWPAN: Use connected oriented channel instead of fixed one")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
disconnect_all_peers() calls sleeping function (l2cap_chan_close) under
spinlock. Holding the lock doesn't actually do any good -- we work on a
local copy of the list, and the lock doesn't protect against peer->chan
having already been freed.
Fix by taking refcounts of peer->chan instead. Clean up the code and
old comments a bit.
Take devices_lock instead of RCU, because the kfree_rcu();
l2cap_chan_put(); construct in chan_close_cb() does not guarantee
peer->chan is necessarily valid in RCU.
Also take l2cap_chan_lock() which is required for l2cap_chan_close().
Log: (bluez 6lowpan-tester Client Connect - Disable)
------
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:575
...
<TASK>
...
l2cap_send_disconn_req (net/bluetooth/l2cap_core.c:938 net/bluetooth/l2cap_core.c:1495)
...
? __pfx_l2cap_chan_close (net/bluetooth/l2cap_core.c:809)
do_enable_set (net/bluetooth/6lowpan.c:1048 net/bluetooth/6lowpan.c:1068)
------
Fixes: 9030582963 ("Bluetooth: 6lowpan: Converting rwlocks to use RCU")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
l2cap_chan_put() is exported, so export also l2cap_chan_hold() for
modules.
l2cap_chan_hold() has use case in net/bluetooth/6lowpan.c
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth 6lowpan.c confuses BDADDR_LE and ADDR_LE_DEV address types,
e.g. debugfs "connect" command takes the former, and "disconnect" and
"connect" to already connected device take the latter. This is due to
using same value both for l2cap_chan_connect and hci_conn_hash_lookup_le
which take different dst_type values.
Fix address type passed to hci_conn_hash_lookup_le().
Retain the debugfs API difference between "connect" and "disconnect"
commands since it's been like this since 2015 and nobody apparently
complained.
Fixes: f5ad4ffceb ("Bluetooth: 6lowpan: Use hci_conn_hash_lookup_le() when possible")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth 6lowpan.c netdev has header_ops, so it must set link-local
header for RX skb, otherwise things crash, eg. with AF_PACKET SOCK_RAW
Add missing skb_reset_mac_header() for uncompressed ipv6 RX path.
For the compressed one, it is done in lowpan_header_decompress().
Log: (BlueZ 6lowpan-tester Client Recv Raw - Success)
------
kernel BUG at net/core/skbuff.c:212!
Call Trace:
<IRQ>
...
packet_rcv (net/packet/af_packet.c:2152)
...
<TASK>
__local_bh_enable_ip (kernel/softirq.c:407)
netif_rx (net/core/dev.c:5648)
chan_recv_cb (net/bluetooth/6lowpan.c:294 net/bluetooth/6lowpan.c:359)
------
Fixes: 18722c2470 ("Bluetooth: Enable 6LoWPAN support for BT LE devices")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
mesh_send_done timer is not canceled when hdev is removed, which causes
crash if the timer triggers after hdev is gone.
Cancel the timer when MGMT removes the hdev, like other MGMT timers.
Should fix the BUG: sporadically seen by BlueZ test bot
(in "Mesh - Send cancel - 1" test).
Log:
------
BUG: KASAN: slab-use-after-free in run_timer_softirq+0x76b/0x7d0
...
Freed by task 36:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
__kasan_save_free_info+0x3a/0x60
__kasan_slab_free+0x43/0x70
kfree+0x103/0x500
device_release+0x9a/0x210
kobject_put+0x100/0x1e0
vhci_release+0x18b/0x240
------
Fixes: b338d91703 ("Bluetooth: Implement support for Mesh")
Link: https://lore.kernel.org/linux-bluetooth/67364c09.0c0a0220.113cba.39ff@mx.google.com/
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The Smatch static checker noted that in _nfs4_proc_lookupp(), the flag
RPC_TASK_TIMEOUT is being passed as an argument to nfs4_init_sequence(),
which is clearly incorrect.
Since LOOKUPP is an idempotent operation, nfs4_init_sequence() should
not ask the server to cache the result. The RPC_TASK_TIMEOUT flag needs
to be passed down to the RPC layer.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Reported-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Fixes: 76998ebb91 ("NFSv4: Observe the NFS_MOUNT_SOFTREVAL flag in _nfs4_proc_lookupp")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
If adding the second kobject fails, drop both references to avoid sysfs
residue and memory leak.
Fixes: e96f9268ee ("NFS: Make all of /sys/fs/nfs network-namespace unique")
Signed-off-by: Yang Xiuwei <yangxiuwei@kylinos.cn>
Reviewed-by: Benjamin Coddington <ben.coddington@hammerspace.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
From https://lore.kernel.org/linux-nfs/aQHASIumLJyOoZGH@infradead.org/
On Wed, Oct 29, 2025 at 12:20:40AM -0700, Christoph Hellwig wrote:
> On Mon, Oct 27, 2025 at 12:18:30PM -0400, Mike Snitzer wrote:
> > LOCALIO's misaligned DIO will issue head/tail followed by O_DIRECT
> > middle (via AIO completion of that aligned middle). So out of order
> > relative to file offset.
>
> That's in general a really bad idea. It will obviously work, but
> both on SSDs and out of place write file systems it is a sure way
> to increase your garbage collection overhead a lot down the line.
Fix this by never issuing misaligned DIO out of order. This fix means
the DIO-aligned middle will only use AIO completion if there is no
misaligned end segment. Otherwise, all 3 segments of a misaligned DIO
will be issued without AIO completion to ensure file offset increases
properly for all partial READ or WRITE situations.
Factoring out nfs_local_iter_setup() helps standardize repetitive
nfs_local_iters_setup_dio() code and is inspired by cleanup work that
Chuck Lever did on the NFSD Direct code.
Fixes: c817248fc8 ("nfs/localio: add proper O_DIRECT support for READ and WRITE")
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
The WMI driver core only supports GUID strings containing only
uppercase characters, however the GUID string used by the
msi-wmi-platform driver contains a single lowercase character.
This prevents the WMI driver core from matching said driver to
its WMI device.
Fix this by turning the lowercase character into a uppercase
character. Also update the WMI driver development guide to warn
about this.
Reported-by: Antheas Kapenekakis <lkml@antheas.dev>
Fixes: 9c0beb6b29 ("platform/x86: wmi: Add MSI WMI Platform driver")
Tested-by: Antheas Kapenekakis <lkml@antheas.dev>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20251110111253.16204-3-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
It turns out that the GUID used by the msi-wmi-platform driver
(ABBC0F60-8EA1-11D1-00A0-C90629100000) is not unique, but was instead
copied from the WIndows Driver Samples. This means that this driver
could load on devices from other manufacturers that also copied this
GUID, potentially causing hardware errors.
Prevent this by only loading on devices whitelisted via DMI. The DMI
matches where taken from the msi-ec driver.
Reported-by: Antheas Kapenekakis <lkml@antheas.dev>
Fixes: 9c0beb6b29 ("platform/x86: wmi: Add MSI WMI Platform driver")
Tested-by: Antheas Kapenekakis <lkml@antheas.dev>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20251110111253.16204-2-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Pull kvm fixes from Paolo Bonzini:
"Arm:
- Fix trapping regression when no in-kernel irqchip is present
- Check host-provided, untrusted ranges and offsets in pKVM
- Fix regression restoring the ID_PFR1_EL1 register
- Fix vgic ITS locking issues when LPIs are not directly injected
Arm selftests:
- Correct target CPU programming in vgic_lpi_stress selftest
- Fix exposure of SCTLR2_EL2 and ZCR_EL2 in get-reg-list selftest
RISC-V:
- Fix check for local interrupts on riscv32
- Read HGEIP CSR on the correct cpu when checking for IMSIC
interrupts
- Remove automatic I/O mapping from kvm_arch_prepare_memory_region()
x86:
- Inject #UD if the guest attempts to execute SEAMCALL or TDCALL as
KVM doesn't support virtualization the instructions, but the
instructions are gated only by VMXON. That is, they will VM-Exit
instead of taking a #UD and until now this resulted in KVM exiting
to userspace with an emulation error.
- Unload the "FPU" when emulating INIT of XSTATE features if and only
if the FPU is actually loaded, instead of trying to predict when
KVM will emulate an INIT (CET support missed the MP_STATE path).
Add sanity checks to detect and harden against similar bugs in the
future.
- Unregister KVM's GALog notifier (for AVIC) when kvm-amd.ko is
unloaded.
- Use a raw spinlock for svm->ir_list_lock as the lock is taken
during schedule(), and "normal" spinlocks are sleepable locks when
PREEMPT_RT=y.
- Remove guest_memfd bindings on memslot deletion when a gmem file is
dying to fix a use-after-free race found by syzkaller.
- Fix a goof in the EPT Violation handler where KVM checks the wrong
variable when determining if the reported GVA is valid.
- Fix and simplify the handling of LBR virtualization on AMD, which
was made buggy and unnecessarily complicated by nested VM support
Misc:
- Update Oliver's email address"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
KVM: nSVM: Fix and simplify LBR virtualization handling with nested
KVM: nSVM: Always recalculate LBR MSR intercepts in svm_update_lbrv()
KVM: SVM: Mark VMCB_LBR dirty when MSR_IA32_DEBUGCTLMSR is updated
MAINTAINERS: Switch myself to using kernel.org address
KVM: arm64: vgic-v3: Release reserved slot outside of lpi_xa's lock
KVM: arm64: vgic-v3: Reinstate IRQ lock ordering for LPI xarray
KVM: arm64: Limit clearing of ID_{AA64PFR0,PFR1}_EL1.GIC to userspace irqchip
KVM: arm64: Set ID_{AA64PFR0,PFR1}_EL1.GIC when GICv3 is configured
KVM: arm64: Make all 32bit ID registers fully writable
KVM: VMX: Fix check for valid GVA on an EPT violation
KVM: guest_memfd: Remove bindings on memslot deletion when gmem is dying
KVM: SVM: switch to raw spinlock for svm->ir_list_lock
KVM: SVM: Make avic_ga_log_notifier() local to avic.c
KVM: SVM: Unregister KVM's GALog notifier on kvm-amd.ko exit
KVM: SVM: Initialize per-CPU svm_data at the end of hardware setup
KVM: x86: Call out MSR_IA32_S_CET is not handled by XSAVES
KVM: x86: Harden KVM against imbalanced load/put of guest FPU state
KVM: x86: Unload "FPU" state on INIT if and only if its currently in-use
KVM: arm64: Check the untrusted offset in FF-A memory share
KVM: arm64: Check range args for pKVM mem transitions
...
LOCALIO's misaligned DIO WRITE support requires synchronous IO for any
misaligned head and/or tail that are issued using buffered IO. In
addition, it is important that the O_DIRECT middle be on stable
storage upon its completion via AIO.
Otherwise, a misaligned DIO WRITE could mix buffered IO for the
head/tail and direct IO for the DIO-aligned middle -- which could lead
to problems associated with deferred writes to stable storage (such as
out of order partial completions causing incorrect advancement of the
file's offset, etc).
Fixes: c817248fc8 ("nfs/localio: add proper O_DIRECT support for READ and WRITE")
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
Misaligned DIO read can be split into 3 IOs, must handle potential for
short read from each component IO (follows same pattern used for
handling partial writes, except upper layer read code handles advancing
offset before retry).
Fixes: c817248fc8 ("nfs/localio: add proper O_DIRECT support for READ and WRITE")
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
Improve completion handling of as many as 3 IOs associated with each
misaligned DIO by using a atomic_t to track completion of each IO.
Update nfs_local_pgio_done() to use precise atomic_t accounting for
remaining iov_iter (up to 3) associated with each iocb, so that each
NFS LOCALIO pgio header is only released after all IOs have completed.
But also allow early return if/when a short read or write occurs.
Fixes reported BUG: KASAN: slab-use-after-free in nfs_local_call_read:
https://lore.kernel.org/linux-nfs/aPSvi5Yr2lGOh5Jh@dell-per750-06-vm-07.rhts.eng.pek2.redhat.com/
Reported-by: Yongcheng Yang <yoyang@redhat.com>
Fixes: c817248fc8 ("nfs/localio: add proper O_DIRECT support for READ and WRITE")
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
Each filesystem is meant to fallback to retrying DIO in terms buffered
IO when it might encounter -ENOTBLK when issuing DIO (which can happen
if the VFS cannot invalidate the page cache).
So NFS doesn't need special handling for -ENOTBLK.
Also, explicitly initialize a couple DIO related iocb members rather
than simply rely on data structure zeroing.
Fixes: c817248fc8 ("nfs/localio: add proper O_DIRECT support for READ and WRITE")
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
If the TLS security policy is of type RPC_XPRTSEC_TLS_X509, then the
cert_serial and privkey_serial fields need to match as well since they
define the client's identity, as presented to the server.
Fixes: 90c9550a8d ("NFS: support the kernel keyring for TLS")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
The default setting for the transport security policy must be
RPC_XPRTSEC_NONE, when using a TCP or RDMA connection without TLS.
Conversely, when using TLS, the security policy needs to be set.
Fixes: 6c0a8c5fcf ("NFS: Have struct nfs_client carry a TLS policy field")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
Don't try to add an RDMA transport to a client that is already marked as
being a TCP/TLS transport.
Fixes: a35518cae4 ("NFSv4.1/pnfs: fix NFS with TLS in pnfs")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
Don't try to add an RDMA transport to a client that is already marked as
being a TCP/TLS transport.
Fixes: 04a1526366 ("pnfs/flexfiles: connect to NFSv3 DS using TLS if MDS connection uses TLS")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
First, we can't assume pipe == crtc index. If a pipe is fused off in
between, it no longer holds. intel_crtc_for_pipe() is the only proper
way to get from a pipe to the corresponding crtc.
Second, drivers aren't supposed to access or index drm->vblank[]
directly. There's drm_crtc_vblank_crtc() for this.
Use both functions to fix the pipe to vblank conversion.
Fixes: f02658c46c ("drm/i915/psr: Add mechanism to notify PSR of pipe enable/disable")
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: stable@vger.kernel.org # v6.16+
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patch.msgid.link/20251106200000.1455164-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 2750f6765d6974f7e163c5d540a96c8703f6d8dd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
nfsd4_enc_sequence_replay() uses nfsd4_encode_operation() to encode a
new SEQUENCE reply when replaying a request from the slot cache - only
ops after the SEQUENCE are replayed from the cache in ->sl_data.
However it does this in nfsd4_replay_cache_entry() which is called
*before* nfsd4_sequence() has filled in reply fields.
This means that in the replayed SEQUENCE reply:
maxslots will be whatever the client sent
target_maxslots will be -1 (assuming init to zero, and
nfsd4_encode_sequence() subtracts 1)
status_flags will be zero
The incorrect maxslots value, in particular, can cause the client to
think the slot table has been reduced in size so it can discard its
knowledge of current sequence number of the later slots, though the
server has not discarded those slots. When the client later wants to
use a later slot, it can get NFS4ERR_SEQ_MISORDERED from the server.
This patch moves the setup of the reply into a new helper function and
call it *before* nfsd4_replay_cache_entry() is called. Only one of the
updated fields was used after this point - maxslots. So the
nfsd4_sequence struct has been extended to have separate maxslots for
the request and the response.
Reported-by: Olga Kornievskaia <okorniev@redhat.com>
Closes: https://lore.kernel.org/linux-nfs/20251010194449.10281-1-okorniev@redhat.com/
Tested-by: Olga Kornievskaia <okorniev@redhat.com>
Signed-off-by: NeilBrown <neil@brown.name>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
The PCM stream data in USB-audio driver is transferred over USB URB
packet buffers, and each packet size is determined dynamically. The
packet sizes are limited by some factors such as wMaxPacketSize USB
descriptor. OTOH, in the current code, the actually used packet sizes
are determined only by the rate and the PPS, which may be bigger than
the size limit above. This results in a buffer overflow, as reported
by syzbot.
Basically when the limit is smaller than the calculated packet size,
it implies that something is wrong, most likely a weird USB
descriptor. So the best option would be just to return an error at
the parameter setup time before doing any further operations.
This patch introduces such a sanity check, and returns -EINVAL when
the packet size is greater than maxpacksize. The comparison with
ep->packsize[1] alone should suffice since it's always equal or
greater than ep->packsize[0].
Reported-by: syzbot+bfd77469c8966de076f7@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=bfd77469c8966de076f7
Link: https://lore.kernel.org/690b6b46.050a0220.3d0d33.0054.GAE@google.com
Cc: Lizhi Xu <lizhi.xu@windriver.com>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20251109091211.12739-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix kernel-doc warnings so that there no other kernel-doc issues
in <uapi/linux/tee.h>:
- add ending ':' to some struct members as needed for kernel-doc
- change struct name in kernel-doc to match the actual struct name (2x)
- add a @params: kernel-doc entry multiple times
Warning: tee.h:265 struct member 'ret_origin' not described
in 'tee_ioctl_open_session_arg'
Warning: tee.h:265 struct member 'num_params' not described
in 'tee_ioctl_open_session_arg'
Warning: tee.h:265 struct member 'params' not described
in 'tee_ioctl_open_session_arg'
Warning: tee.h:351 struct member 'num_params' not described
in 'tee_iocl_supp_recv_arg'
Warning: tee.h:351 struct member 'params' not described
in 'tee_iocl_supp_recv_arg'
Warning: tee.h:372 struct member 'num_params' not described
in 'tee_iocl_supp_send_arg'
Warning: tee.h:372 struct member 'params' not described
in 'tee_iocl_supp_send_arg'
Warning: tee.h:298: expecting prototype for struct
tee_ioctl_invoke_func_arg. Prototype was for
struct tee_ioctl_invoke_arg instead
Warning: tee.h:473: expecting prototype for struct
tee_ioctl_invoke_func_arg. Prototype was for struct
tee_ioctl_object_invoke_arg instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
kho_vmalloc_unpreserve_chunk() calls __kho_unpreserve() with end_pfn as
pfn + 1. This happens to work for 0-order pages, but leaks higher order
pages.
For example, say order 2 pages back the allocation. During preservation,
they get preserved in the order 2 bitmaps, but
kho_vmalloc_unpreserve_chunk() would try to unpreserve them from the order
0 bitmaps, which should not have these bits set anyway, leaving the order
2 bitmaps untouched. This results in the pages being carried over to the
next kernel. Nothing will free those pages in the next boot, leaking
them.
Fix this by taking the order into account when calculating the end PFN for
__kho_unpreserve().
Link: https://lkml.kernel.org/r/20251103180235.71409-2-pratyush@kernel.org
Fixes: a667300bd5 ("kho: add support for preserving vmalloc allocations")
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Cc: Alexander Graf <graf@amazon.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Pasha Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The list of pages in a vmalloc chunk is NULL-terminated. So when looping
through the pages in a vmalloc chunk, both kho_restore_vmalloc() and
kho_vmalloc_unpreserve_chunk() rightly make sure to stop when encountering
a NULL page. But when the chunk is full, the loops do not stop and go
past the bounds of chunk->phys, resulting in out-of-bounds memory access,
and possibly the restoration or unpreservation of an invalid page.
Fix this by making sure the processing of chunk stops at the end of the
array.
Link: https://lkml.kernel.org/r/20251103110159.8399-1-pratyush@kernel.org
Fixes: a667300bd5 ("kho: add support for preserving vmalloc allocations")
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Cc: Alexander Graf <graf@amazon.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Pasha Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When a page fault occurs in a secret memory file created with
`memfd_secret(2)`, the kernel will allocate a new folio for it, mark the
underlying page as not-present in the direct map, and add it to the file
mapping.
If two tasks cause a fault in the same page concurrently, both could end
up allocating a folio and removing the page from the direct map, but only
one would succeed in adding the folio to the file mapping. The task that
failed undoes the effects of its attempt by (a) freeing the folio again
and (b) putting the page back into the direct map. However, by doing
these two operations in this order, the page becomes available to the
allocator again before it is placed back in the direct mapping.
If another task attempts to allocate the page between (a) and (b), and the
kernel tries to access it via the direct map, it would result in a
supervisor not-present page fault.
Fix the ordering to restore the direct map before the folio is freed.
Link: https://lkml.kernel.org/r/20251031120955.92116-1-lance.yang@linux.dev
Fixes: 1507f51255 ("mm: introduce memfd_secret system call to create "secret" memory areas")
Signed-off-by: Lance Yang <lance.yang@linux.dev>
Reported-by: Google Big Sleep <big-sleep-vuln-reports@google.com>
Closes: https://lore.kernel.org/linux-mm/CAEXGt5QeDpiHTu3K9tvjUTPqo+d-=wuCNYPa+6sWKrdQJ-ATdg@mail.gmail.com/
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
On arm64 with MTE enabled, a page mapped as Normal Tagged (PROT_MTE) in
user space will need to have its allocation tags initialised. This is
normally done in the arm64 set_pte_at() after checking the memory
attributes. Such page is also marked with the PG_mte_tagged flag to avoid
subsequent clearing. Since this relies on having a struct page,
pte_special() mappings are ignored.
Commit d82d09e482 ("mm/huge_memory: mark PMD mappings of the huge zero
folio special") maps the huge zero folio special and the arm64
set_pmd_at() will no longer zero the tags. There is no guarantee that the
tags are zero, especially if parts of this huge page have been previously
tagged.
It's fairly easy to detect this by regularly dropping the caches to
force the reallocation of the huge zero folio.
Allocate the huge zero folio with the __GFP_ZEROTAGS flag. In addition,
do not warn in the arm64 __access_remote_tags() when reading tags from the
huge zero page.
I bundled the arm64 change in here as well since they are both related to
the commit mapping the huge zero folio as special.
[catalin.marinas@arm.com: handle arch mte_zero_clear_page_tags() code issuing MTE instructions]
Link: https://lkml.kernel.org/r/aQi8dA_QpXM8XqrE@arm.com
Link: https://lkml.kernel.org/r/20251031170133.280742-1-catalin.marinas@arm.com
Fixes: d82d09e482 ("mm/huge_memory: mark PMD mappings of the huge zero folio special")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Lance Yang <lance.yang@linux.dev>
Tested-by: Beleswar Padhi <b-padhi@ti.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Aishwarya TCV <aishwarya.tcv@arm.com>
Cc: David Hildenbrand (Red Hat) <david@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Because kthread_stop did not stop sc_task properly and returned -EINTR,
the sc_timer was not properly closed, ultimately causing the problem [1]
reported by syzbot when freeing sci due to the sc_timer not being closed.
Because the thread sc_task main function nilfs_segctor_thread() returns 0
when it succeeds, when the return value of kthread_stop() is not 0 in
nilfs_segctor_destroy(), we believe that it has not properly closed
sc_timer.
We use timer_shutdown_sync() to sync wait for sc_timer to shutdown, and
set the value of sc_task to NULL under the protection of lock
sc_state_lock, so as to avoid the issue caused by sc_timer not being
properly shutdowned.
[1]
ODEBUG: free active (active state 0) object: 00000000dacb411a object type: timer_list hint: nilfs_construction_timeout
Call trace:
nilfs_segctor_destroy fs/nilfs2/segment.c:2811 [inline]
nilfs_detach_log_writer+0x668/0x8cc fs/nilfs2/segment.c:2877
nilfs_put_super+0x4c/0x12c fs/nilfs2/super.c:509
Link: https://lkml.kernel.org/r/20251029225226.16044-1-konishi.ryusuke@gmail.com
Fixes: 3f66cc261c ("nilfs2: use kthread_create and kthread_stop for the log writer thread")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+24d8b70f039151f65590@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=24d8b70f039151f65590
Tested-by: syzbot+24d8b70f039151f65590@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Cc: <stable@vger.kernel.org> [6.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Support for parsing PC source info in stacktraces (e.g. '(P)') was added
in commit 2bff77c665 ("scripts/decode_stacktrace.sh: fix decoding of
lines with an additional info"). However, this logic was placed after the
build ID processing. This incorrect order fails to parse lines containing
both elements, e.g.:
drm_gem_mmap_obj+0x114/0x200 [drm 03d0564e0529947d67bb2008c3548be77279fd27] (P)
This patch fixes the problem by extracting the PC source info first and
then processing the module build ID. With this change, the line above is
now properly parsed as such:
drm_gem_mmap_obj (./include/linux/mmap_lock.h:212 ./include/linux/mm.h:811 drivers/gpu/drm/drm_gem.c:1177) drm (P)
While here, also add a brief explanation the build ID section.
Link: https://lkml.kernel.org/r/20251030010347.2731925-1-cmllamas@google.com
Fixes: 2bff77c665 ("scripts/decode_stacktrace.sh: fix decoding of lines with an additional info")
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Cc: Breno Leitao <leitao@debian.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Rutland <mark.rutland@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Matthieu Baerts <matttbe@kernel.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Puranjay Mohan <puranjay@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In DAMON's damon_sysfs_repeat_call_fn(), time_before() is used to compare
the current jiffies with next_update_jiffies to determine whether to
update the sysfs files at this moment.
On 32-bit systems, the kernel initializes jiffies to "-5 minutes" to make
jiffies wrap bugs appear earlier. However, this causes time_before() in
damon_sysfs_repeat_call_fn() to unexpectedly return true during the first
5 minutes after boot on 32-bit systems (see [1] for more explanation,
which fixes another jiffies-related issue before). As a result, DAMON
does not update sysfs files during that period.
There is also an issue unrelated to the system's word size[2]: if the
user stops DAMON just after next_update_jiffies is updated and restarts
it after 'refresh_ms' or a longer delay, next_update_jiffies will retain
an older value, causing time_before() to return false and the update to
happen earlier than expected.
Fix these issues by making next_update_jiffies a global variable and
initializing it each time DAMON is started.
Link: https://lkml.kernel.org/r/20251030020746.967174-3-yanquanmin1@huawei.com
Link: https://lkml.kernel.org/r/20250822025057.1740854-1-ekffu200098@gmail.com [1]
Link: https://lore.kernel.org/all/20251029013038.66625-1-sj@kernel.org/ [2]
Fixes: d809a7c64b ("mm/damon/sysfs: implement refresh_ms file internal work")
Suggested-by: SeongJae Park <sj@kernel.org>
Reviewed-by: SeongJae Park <sj@kernel.org>
Signed-off-by: Quanmin Yan <yanquanmin1@huawei.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: ze zuo <zuoze1@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "mm/damon: fixes for the jiffies-related issues", v2.
On 32-bit systems, the kernel initializes jiffies to "-5 minutes" to make
jiffies wrap bugs appear earlier. However, this may cause the
time_before() series of functions to return unexpected values, resulting
in DAMON not functioning as intended. Meanwhile, similar issues exist in
some specific user operation scenarios.
This patchset addresses these issues. The first patch is about the
DAMON_STAT module, and the second patch is about the core layer's sysfs.
This patch (of 2):
In DAMON_STAT's damon_stat_damon_call_fn(), time_before_eq() is used to
avoid unnecessarily frequent stat update.
On 32-bit systems, the kernel initializes jiffies to "-5 minutes" to make
jiffies wrap bugs appear earlier. However, this causes time_before_eq()
in DAMON_STAT to unexpectedly return true during the first 5 minutes after
boot on 32-bit systems (see [1] for more explanation, which fixes another
jiffies-related issue before). As a result, DAMON_STAT does not update
any monitoring results during that period, which becomes more confusing
when DAMON_STAT_ENABLED_DEFAULT is enabled.
There is also an issue unrelated to the system's word size[2]: if the user
stops DAMON_STAT just after last_refresh_jiffies is updated and restarts
it after 5 seconds or a longer delay, last_refresh_jiffies will retain an
older value, causing time_before_eq() to return false and the update to
happen earlier than expected.
Fix these issues by making last_refresh_jiffies a global variable and
initializing it each time DAMON_STAT is started.
Link: https://lkml.kernel.org/r/20251030020746.967174-2-yanquanmin1@huawei.com
Link: https://lkml.kernel.org/r/20250822025057.1740854-1-ekffu200098@gmail.com [1]
Link: https://lore.kernel.org/all/20251028143250.50144-1-sj@kernel.org/ [2]
Fixes: fabdd1e911 ("mm/damon/stat: calculate and expose estimated memory bandwidth")
Signed-off-by: Quanmin Yan <yanquanmin1@huawei.com>
Suggested-by: SeongJae Park <sj@kernel.org>
Reviewed-by: SeongJae Park <sj@kernel.org>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: ze zuo <zuoze1@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
maple_tree tracepoints contain pointers to function names. Such a pointer
is saved when a tracepoint logs an event. There's no guarantee that it's
still valid when the event is parsed later and the pointer is dereferenced.
The kernel warns about these unsafe pointers.
event 'ma_read' has unsafe pointer field 'fn'
WARNING: kernel/trace/trace.c:3779 at ignore_event+0x1da/0x1e4
Mark the function names as tracepoint_string() to fix the events.
One case that doesn't work without my patch would be trace-cmd record
to save the binary ringbuffer and trace-cmd report to parse it in
userspace. The address of __func__ can't be dereferenced from
userspace but tracepoint_string will add an entry to
/sys/kernel/tracing/printk_formats
Link: https://lkml.kernel.org/r/20251030155537.87972-1-martin@kaiser.cx
Fixes: 54a611b605 ("Maple Tree: add new data structure")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When emitting the order of the allocation for a hash table,
alloc_large_system_hash() unconditionally subtracts PAGE_SHIFT from log
base 2 of the allocation size. This is not correct if the allocation size
is smaller than a page, and yields a negative value for the order as seen
below:
TCP established hash table entries: 32 (order: -4, 256 bytes, linear) TCP
bind hash table entries: 32 (order: -2, 1024 bytes, linear)
Use get_order() to compute the order when emitting the hash table
information to correctly handle cases where the allocation size is smaller
than a page:
TCP established hash table entries: 32 (order: 0, 256 bytes, linear) TCP
bind hash table entries: 32 (order: 0, 1024 bytes, linear)
Link: https://lkml.kernel.org/r/20251028191020.413002-1-isaacmanjarres@google.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Isaac J. Manjarres <isaacmanjarres@google.com>
Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "Fix SIGBUS semantics with large folios", v3.
Accessing memory within a VMA, but beyond i_size rounded up to the next
page size, is supposed to generate SIGBUS.
Darrick reported[1] an xfstests regression in v6.18-rc1. generic/749
failed due to missing SIGBUS. This was caused by my recent changes that
try to fault in the whole folio where possible:
19773df031 ("mm/fault: try to map the entire file folio in finish_fault()")
357b92761d ("mm/filemap: map entire large folio faultaround")
These changes did not consider i_size when setting up PTEs, leading to
xfstest breakage.
However, the problem has been present in the kernel for a long time -
since huge tmpfs was introduced in 2016. The kernel happily maps
PMD-sized folios as PMD without checking i_size. And huge=always tmpfs
allocates PMD-size folios on any writes.
I considered this corner case when I implemented a large tmpfs, and my
conclusion was that no one in their right mind should rely on receiving a
SIGBUS signal when accessing beyond i_size. I cannot imagine how it could
be useful for the workload.
But apparently filesystem folks care a lot about preserving strict SIGBUS
semantics.
Generic/749 was introduced last year with reference to POSIX, but no real
workloads were mentioned. It also acknowledged the tmpfs deviation from
the test case.
POSIX indeed says[3]:
References within the address range starting at pa and
continuing for len bytes to whole pages following the end of an
object shall result in delivery of a SIGBUS signal.
The patchset fixes the regression introduced by recent changes as well as
more subtle SIGBUS breakage due to split failure on truncation.
This patch (of 2):
Accesses within VMA, but beyond i_size rounded up to PAGE_SIZE are
supposed to generate SIGBUS.
Recent changes attempted to fault in full folio where possible. They did
not respect i_size, which led to populating PTEs beyond i_size and
breaking SIGBUS semantics.
Darrick reported generic/749 breakage because of this.
However, the problem existed before the recent changes. With huge=always
tmpfs, any write to a file leads to PMD-size allocation. Following the
fault-in of the folio will install PMD mapping regardless of i_size.
Fix filemap_map_pages() and finish_fault() to not install:
- PTEs beyond i_size;
- PMD mappings across i_size;
Make an exception for shmem/tmpfs that for long time intentionally
mapped with PMDs across i_size.
Link: https://lkml.kernel.org/r/20251027115636.82382-1-kirill@shutemov.name
Link: https://lkml.kernel.org/r/20251027115636.82382-2-kirill@shutemov.name
Signed-off-by: Kiryl Shutsemau <kas@kernel.org>
Fixes: 6795801366 ("xfs: Support large folios")
Reported-by: "Darrick J. Wong" <djwong@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Shakeel Butt <shakeel.butt@linux.dev>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Pde is erased from subdir rbtree through rb_erase(), but not set the node
to EMPTY, which may result in uaf access. We should use RB_CLEAR_NODE()
set the erased node to EMPTY, then pde_subdir_next() will return NULL to
avoid uaf access.
We found an uaf issue while using stress-ng testing, need to run testcase
getdent and tun in the same time. The steps of the issue is as follows:
1) use getdent to traverse dir /proc/pid/net/dev_snmp6/, and current
pde is tun3;
2) in the [time windows] unregister netdevice tun3 and tun2, and erase
them from rbtree. erase tun3 first, and then erase tun2. the
pde(tun2) will be released to slab;
3) continue to getdent process, then pde_subdir_next() will return
pde(tun2) which is released, it will case uaf access.
CPU 0 | CPU 1
-------------------------------------------------------------------------
traverse dir /proc/pid/net/dev_snmp6/ | unregister_netdevice(tun->dev) //tun3 tun2
sys_getdents64() |
iterate_dir() |
proc_readdir() |
proc_readdir_de() | snmp6_unregister_dev()
pde_get(de); | proc_remove()
read_unlock(&proc_subdir_lock); | remove_proc_subtree()
| write_lock(&proc_subdir_lock);
[time window] | rb_erase(&root->subdir_node, &parent->subdir);
| write_unlock(&proc_subdir_lock);
read_lock(&proc_subdir_lock); |
next = pde_subdir_next(de); |
pde_put(de); |
de = next; //UAF |
rbtree of dev_snmp6
|
pde(tun3)
/ \
NULL pde(tun2)
Link: https://lkml.kernel.org/r/20251025024233.158363-1-albin_yang@163.com
Signed-off-by: Wei Yang <albinwyang@tencent.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: wangzijie <wangzijie1@honor.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Currently, scan_get_next_rmap_item() walks every page address in a VMA to
locate mergeable pages. This becomes highly inefficient when scanning
large virtual memory areas that contain mostly unmapped regions, causing
ksmd to use large amount of cpu without deduplicating much pages.
This patch replaces the per-address lookup with a range walk using
walk_page_range(). The range walker allows KSM to skip over entire
unmapped holes in a VMA, avoiding unnecessary lookups. This problem was
previously discussed in [1].
Consider the following test program which creates a 32 TiB mapping in the
virtual address space but only populates a single page:
#include <unistd.h>
#include <stdio.h>
#include <sys/mman.h>
/* 32 TiB */
const size_t size = 32ul * 1024 * 1024 * 1024 * 1024;
int main() {
char *area = mmap(NULL, size, PROT_READ | PROT_WRITE,
MAP_NORESERVE | MAP_PRIVATE | MAP_ANON, -1, 0);
if (area == MAP_FAILED) {
perror("mmap() failed\n");
return -1;
}
/* Populate a single page such that we get an anon_vma. */
*area = 0;
/* Enable KSM. */
madvise(area, size, MADV_MERGEABLE);
pause();
return 0;
}
$ ./ksm-sparse &
$ echo 1 > /sys/kernel/mm/ksm/run
Without this patch ksmd uses 100% of the cpu for a long time (more then 1
hour in my test machine) scanning all the 32 TiB virtual address space
that contain only one mapped page. This makes ksmd essentially deadlocked
not able to deduplicate anything of value. With this patch ksmd walks
only the one mapped page and skips the rest of the 32 TiB virtual address
space, making the scan fast using little cpu.
Link: https://lkml.kernel.org/r/20251023035841.41406-1-pedrodemargomes@gmail.com
Link: https://lkml.kernel.org/r/20251022153059.22763-1-pedrodemargomes@gmail.com
Link: https://lore.kernel.org/linux-mm/423de7a3-1c62-4e72-8e79-19a6413e420c@redhat.com/ [1]
Fixes: 31dbd01f31 ("ksm: Kernel SamePage Merging")
Signed-off-by: Pedro Demarchi Gomes <pedrodemargomes@gmail.com>
Co-developed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: craftfever <craftfever@airmail.cc>
Closes: https://lkml.kernel.org/r/020cf8de6e773bb78ba7614ef250129f11a63781@murena.io
Suggested-by: David Hildenbrand <david@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Chengming Zhou <chengming.zhou@linux.dev>
Cc: xu xin <xu.xin16@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
KHO allocates metadata for its preserved memory map using the slab
allocator via kzalloc(). This metadata is temporary and is used by the
next kernel during early boot to find preserved memory.
A problem arises when KFENCE is enabled. kzalloc() calls can be randomly
intercepted by kfence_alloc(), which services the allocation from a
dedicated KFENCE memory pool. This pool is allocated early in boot via
memblock.
When booting via KHO, the memblock allocator is restricted to a "scratch
area", forcing the KFENCE pool to be allocated within it. This creates a
conflict, as the scratch area is expected to be ephemeral and
overwriteable by a subsequent kexec. If KHO metadata is placed in this
KFENCE pool, it leads to memory corruption when the next kernel is loaded.
To fix this, modify KHO to allocate its metadata directly from the buddy
allocator instead of slab.
Link: https://lkml.kernel.org/r/20251021000852.2924827-4-pasha.tatashin@soleen.com
Fixes: fc33e4b44b ("kexec: enable KHO support for memory preservation")
Signed-off-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Reviewed-by: David Matlack <dmatlack@google.com>
Cc: Alexander Graf <graf@amazon.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Miguel Ojeda <ojeda@kernel.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Samiullah Khawaja <skhawaja@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
KHO memory preservation metadata is preserved in 512 byte chunks which
requires their allocation from slab allocator. Slabs are not safe to be
used with KHO because of kfence, and because partial slabs may lead leaks
to the next kernel. Change the size to be PAGE_SIZE.
The kfence specifically may cause memory corruption, where it randomly
provides slab objects that can be within the scratch area. The reason for
that is that kfence allocates its objects prior to KHO scratch is marked
as CMA region.
While this change could potentially increase metadata overhead on systems
with sparsely preserved memory, this is being mitigated by ongoing work to
reduce sparseness during preservation via 1G guest pages. Furthermore,
this change aligns with future work on a stateless KHO, which will also
use page-sized bitmaps for its radix tree metadata.
Link: https://lkml.kernel.org/r/20251021000852.2924827-3-pasha.tatashin@soleen.com
Fixes: fc33e4b44b ("kexec: enable KHO support for memory preservation")
Signed-off-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Cc: Alexander Graf <graf@amazon.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: David Matlack <dmatlack@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Miguel Ojeda <ojeda@kernel.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Samiullah Khawaja <skhawaja@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "KHO: kfence + KHO memory corruption fix", v3.
This series fixes a memory corruption bug in KHO that occurs when KFENCE
is enabled.
The root cause is that KHO metadata, allocated via kzalloc(), can be
randomly serviced by kfence_alloc(). When a kernel boots via KHO, the
early memblock allocator is restricted to a "scratch area". This forces
the KFENCE pool to be allocated within this scratch area, creating a
conflict. If KHO metadata is subsequently placed in this pool, it gets
corrupted during the next kexec operation.
Google is using KHO and have had obscure crashes due to this memory
corruption, with stacks all over the place. I would prefer this fix to be
properly backported to stable so we can also automatically consume it once
we switch to the upstream KHO.
Patch 1/3 introduces a debug-only feature (CONFIG_KEXEC_HANDOVER_DEBUG)
that adds checks to detect and fail any operation that attempts to place
KHO metadata or preserved memory within the scratch area. This serves as
a validation and diagnostic tool to confirm the problem without affecting
production builds.
Patch 2/3 Increases bitmap to PAGE_SIZE, so buddy allocator can be used.
Patch 3/3 Provides the fix by modifying KHO to allocate its metadata
directly from the buddy allocator instead of slab. This bypasses the
KFENCE interception entirely.
This patch (of 3):
It is invalid for KHO metadata or preserved memory regions to be located
within the KHO scratch area, as this area is overwritten when the next
kernel is loaded, and used early in boot by the next kernel. This can
lead to memory corruption.
Add checks to kho_preserve_* and KHO's internal metadata allocators
(xa_load_or_alloc, new_chunk) to verify that the physical address of the
memory does not overlap with any defined scratch region. If an overlap is
detected, the operation will fail and a WARN_ON is triggered. To avoid
performance overhead in production kernels, these checks are enabled only
when CONFIG_KEXEC_HANDOVER_DEBUG is selected.
[rppt@kernel.org: fix KEXEC_HANDOVER_DEBUG Kconfig dependency]
Link: https://lkml.kernel.org/r/aQHUyyFtiNZhx8jo@kernel.org
[pasha.tatashin@soleen.com: build fix]
Link: https://lkml.kernel.org/r/CA+CK2bBnorfsTymKtv4rKvqGBHs=y=MjEMMRg_tE-RME6n-zUw@mail.gmail.com
Link: https://lkml.kernel.org/r/20251021000852.2924827-1-pasha.tatashin@soleen.com
Link: https://lkml.kernel.org/r/20251021000852.2924827-2-pasha.tatashin@soleen.com
Fixes: fc33e4b44b ("kexec: enable KHO support for memory preservation")
Signed-off-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Mike Rapoport <rppt@kernel.org>
Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Cc: Alexander Graf <graf@amazon.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: David Matlack <dmatlack@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Miguel Ojeda <ojeda@kernel.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Samiullah Khawaja <skhawaja@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
VM fails to boot with 256 vCPUs, the detailed command is
qemu-system-loongarch64 -smp 256
and there is an error reported as follows:
KVM_LOONGARCH_EXTIOI_INIT_NUM_CPU failed: Invalid argument
There is typo issue in function kvm_eiointc_ctrl_access() when set
max supported vCPUs.
Cc: stable@vger.kernel.org
Fixes: 47256c4c8b ("LoongArch: KVM: Avoid copy_*_user() with lock hold in kvm_eiointc_ctrl_access()")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
PMU hardware about VM is switched on VM exit to host rather than vCPU
context sched off, PMU is checked and restored on return to VM. It is
not necessary to check PMU on vCPU context sched on callback, since the
request is made on the VM exit entry or VM PMU CSR access abort routine
already.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
On LoongArch system, guest PMU hardware is shared by guest and host but
PMU interrupt is separated. PMU is pass-through to VM, and there is PMU
context switch when exit to host and return to guest.
There is optimiation to check whether PMU is enabled by guest. If not,
it is not necessary to return to guest. However, if it is enabled, PMU
context for guest need switch on. Now KVM_REQ_PMU notification is set
on vCPU context switch, but it is missing if there is no vCPU context
switch while PMU is used by guest VM, so fix it.
Cc: <stable@vger.kernel.org>
Fixes: f4e40ea9f7 ("LoongArch: KVM: Add PMU support for guest")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
When timer is fired in oneshot mode, CSR.TVAL will stop with value -1
rather than 0. However when the register CSR.TVAL is restored, it will
continue to count down rather than stop there.
Now the method is to write 0 to CSR.TVAL, wait to count down for 1 cycle
at least, which is 10ns with a timer freq 100MHz, and then retore timer
interrupt status. Here add 2 cycles delay to assure that timer interrupt
is injected.
With this patch, timer selftest case passes to run always.
Cc: stable@vger.kernel.org
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
With secondary MMU page table, if there is a read page fault, the page's
write attribute will not set even if it is writable from master MMU page
table. This logic only works if dirty tracking is enabled, so page table
should be set with _PAGE_WRITE if dirty tracking is disabled.
It reduces extra page fault on secondary MMU page table if a VM finishes
migration, when the master MMU page table is ready and the secondary MMU
page is fresh.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
When specifying '-d' for kexec_file_load interface, loaded locations of
kernel/initrd/cmdline etc can be printed out to help debug.
Commit eb7622d908 ("kexec_file, riscv: print out debugging message if
required") fixes the same issue on RISC-V.
So, remove kexec_image_info() because the content has been printed out
in generic code.
And on Loongson-3A5000, the printed messages look like below:
kexec_file: kernel: 00000000d9aad283 kernel_size: 0x2e77f30
kexec_file(EFI): No LoongArch PE image header.
kexec_file: Loaded initrd at 0x80000000 bufsz=0x1637cd0 memsz=0x1638000
kexec_file(ELF): Loaded kernel at 0x9c20000 bufsz=0x27f1800 memsz=0x2950000
kexec_file: nr_segments = 2
kexec_file: segment[0]: buf=0x00000000cc3e6c33 bufsz=0x27f1800 mem=0x9c20000 memsz=0x2950000
kexec_file: segment[1]: buf=0x00000000bb75a541 bufsz=0x1637cd0 mem=0x80000000 memsz=0x1638000
kexec_file: kexec_file_load: type:0, start:0xb15d000 head:0x18db60002 flags:0x8
Signed-off-by: Qiang Ma <maqianga@uniontech.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The kexec_buf structure was previously declared without initialization.
commit bf454ec31a ("kexec_file: allow to place kexec_buf randomly")
added a field that is always read but not consistently populated by all
architectures. This un-initialized field will contain garbage.
This is also triggering a UBSAN warning when the uninitialized data is
accessed:
------------[ cut here ]------------
UBSAN: invalid-load in ./include/linux/kexec.h:210:10
load of value 252 is not a valid value for type '_Bool'
Zero-initializing kexec_buf at declaration ensures all fields are
cleanly set, preventing future instances of uninitialized memory being
used.
Fixes: bf454ec31a ("kexec_file: allow to place kexec_buf randomly")
Link: https://lore.kernel.org/r/20250827-kbuf_all-v1-2-1df9882bb01a@debian.org
Signed-off-by: Youling Tang <tangyouling@kylinos.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
CSR.FWPC and CSR.MWPC are 32bit registers, so use csr_read32() rather
than csr_read64() to read the values of FWPC/MWPC.
Cc: stable@vger.kernel.org
Fixes: edffa33c7b ("LoongArch: Add hardware breakpoints/watchpoints support")
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Remove the unnecessary __GFP_HIGHMEM masking in pud_alloc_one(), which
was introduced with commit 382739797f ("loongarch: convert various
functions to use ptdescs"). GFP_KERNEL doesn't contain __GFP_HIGHMEM.
Signed-off-by: Vishal Moola (Oracle) <vishal.moola@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Now if the PTE/PMD is dirty with _PAGE_DIRTY but without _PAGE_MODIFIED,
after {pte,pmd}_modify() we lose _PAGE_DIRTY, then {pte,pmd}_dirty()
return false and lead to data loss. This can happen in certain scenarios
such as HW PTW doesn't set _PAGE_MODIFIED automatically, so here we need
_PAGE_MODIFIED to record the dirty status (_PAGE_DIRTY).
The new modification involves checking whether the original PTE/PMD has
the _PAGE_DIRTY flag. If it exists, the _PAGE_MODIFIED bit is also set,
ensuring that the {pte,pmd}_dirty() interface can always return accurate
information.
Cc: stable@vger.kernel.org
Co-developed-by: Liupu Wang <wangliupu@loongson.cn>
Signed-off-by: Liupu Wang <wangliupu@loongson.cn>
Signed-off-by: Tianyang Zhang <zhangtianyang@loongson.cn>
Now there 5 places which calculate max_pfn & max_low_pfn:
1. in fdt_setup() for FDT systems;
2. in memblock_init() for ACPI systems;
3. in init_numa_memory() for NUMA systems;
4. in arch_mem_init() to recalculate for "mem=" cmdline;
5. in paging_init() to recalculate for NUMA systems.
Since memblock_init() is called both for ACPI and FDT systems, move the
calculation out of the for_each_efi_memory_desc() loop can eliminate the
first case. The last case is very questionable (may be derived from the
MIPS/Loongson code) and breaks the "mem=" cmdline, so should be removed.
And then the NUMA version of paging_init() can be also eliminated.
After consolidation there are 3 places of calculation:
1. in memblock_init() for both ACPI and FDT systems;
2. in init_numa_memory() to recalculate for NUMA systems;
3. in arch_mem_init() to recalculate for the "mem=" cmdline.
For all cases the calculation is:
max_pfn = PFN_DOWN(memblock_end_of_DRAM());
max_low_pfn = min(PFN_DOWN(HIGHMEM_START), max_pfn);
Cc: stable@vger.kernel.org
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
1. Use phys_addr_t instead of u64, which can work for both 32/64 bits.
2. Check whether the input physical address is above TO_PHYS_MASK (and
return NULL if yes) for the DMW version.
Note: In theory early_ioremap() also need the TO_PHYS_MASK checking, but
the UEFI BIOS pass some DMW virtual addresses.
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Now we use virtual addresses to fill CSR_MERRENTRY/CSR_TLBRENTRY, but
hardware hope physical addresses. Now it works well because the high
bits are ignored above PA_BITS (48 bits), but explicitly use physical
addresses can avoid potential bugs. So fix it.
Cc: stable@vger.kernel.org
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
LoongArch's MSG interrupt features are used across multiple subsystems.
Clarify these features to avoid misuse, existing users will be adjusted
if necessary.
MSGINT: Infrastructure, means the CPU core supports message interupts.
Indicated by CPUCFG1.MSGINT.
AVECINT: AVEC interrupt controller based on MSGINT, means the CPU chip
supports direct message interrupts. Indicated by IOCSR.FEATURES.DMSI.
REDIRECTINT: REDIRECT interrupt controller based on MSGINT and AVECINT,
means the CPU chip supports redirect message interrupts. Indicated by
IOCSR.FEATURES.RMSI.
For example:
Loongson-3A5000/3C5000 doesn't support MSGINT/AVECINT/REDIRECTINT;
Loongson-3A6000 supports MSGINT but doesn't support AVECINT/REDIRECTINT;
Loongson-3C6000 supports MSGINT/AVECINT/REDIRECTINT.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
It's used to work around an objtool issue since commit abb2a55722
("LoongArch: Add cflag -fno-isolate-erroneous-paths-dereference"), but
it's then passed to bindgen and cause an error because Clang does not
have this option.
Fixes: abb2a55722 ("LoongArch: Add cflag -fno-isolate-erroneous-paths-dereference")
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Tested-by: Mingcong Bai <jeffbai@aosc.io>
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
When the per-IP connection limit is exceeded in ksmbd_kthread_fn(),
the code sets ret = -EAGAIN and continues the accept loop without
closing the just-accepted socket. That leaks one socket per rejected
attempt from a single IP and enables a trivial remote DoS.
Release client_sk before continuing.
This bug was found with ZeroPath.
Cc: stable@vger.kernel.org
Signed-off-by: Joshua Rogers <linux@joshua.hu>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
smb_direct_prepare_negotiation() posts a recv and then, if
smb_direct_accept_client() fails, calls put_recvmsg() on the same
buffer. That unmaps and recycles a buffer that is still posted on
the QP., which can lead to device DMA into unmapped or reused memory.
Track whether the recv was posted and only return it if it was never
posted. If accept fails after a post, leave it for teardown to drain
and complete safely.
Signed-off-by: Joshua Rogers <linux@joshua.hu>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
The user calls fsconfig twice, but when the program exits, free() only
frees ctx->source for the second fsconfig, not the first.
Regarding fc->source, there is no code in the fs context related to its
memory reclamation.
To fix this memory leak, release the source memory corresponding to ctx
or fc before each parsing.
syzbot reported:
BUG: memory leak
unreferenced object 0xffff888128afa360 (size 96):
backtrace (crc 79c9c7ba):
kstrdup+0x3c/0x80 mm/util.c:84
smb3_fs_context_parse_param+0x229b/0x36c0 fs/smb/client/fs_context.c:1444
BUG: memory leak
unreferenced object 0xffff888112c7d900 (size 96):
backtrace (crc 79c9c7ba):
smb3_fs_context_fullpath+0x70/0x1b0 fs/smb/client/fs_context.c:629
smb3_fs_context_parse_param+0x2266/0x36c0 fs/smb/client/fs_context.c:1438
Reported-by: syzbot+72afd4c236e6bc3f4bac@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=72afd4c236e6bc3f4bac
Cc: stable@vger.kernel.org
Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
cifs_pick_channel iterates candidate channels using cur. The
reconnect-state test mistakenly used a different variable.
This checked the wrong slot and would cause us to skip a healthy channel
and to dispatch on one that needs reconnect, occasionally failing
operations when a channel was down.
Fix by replacing for the correct variable.
Fixes: fc43a8ac39 ("cifs: cifs_pick_channel should try selecting active channels")
Cc: stable@vger.kernel.org
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Henrique Carvalho <henrique.carvalho@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The driver calls fwnode_get_named_child_node() which takes a reference
on the child node, but never releases it, which causes a reference leak.
Fix by using devm_add_action_or_reset() to automatically release the
reference when the device is removed.
Fixes: d5282a5392 ("pinctrl: cs42l43: Add support for the cs42l43")
Suggested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current scheme for handling LBRV when nested is used is very
complicated, especially when L1 does not enable LBRV (i.e. does not set
LBR_CTL_ENABLE_MASK).
To avoid copying LBRs between VMCB01 and VMCB02 on every nested
transition, the current implementation switches between using VMCB01 or
VMCB02 as the source of truth for the LBRs while L2 is running. If L2
enables LBR, VMCB02 is used as the source of truth. When L2 disables
LBR, the LBRs are copied to VMCB01 and VMCB01 is used as the source of
truth. This introduces significant complexity, and incorrect behavior in
some cases.
For example, on a nested #VMEXIT, the LBRs are only copied from VMCB02
to VMCB01 if LBRV is enabled in VMCB01. This is because L2's writes to
MSR_IA32_DEBUGCTLMSR to enable LBR are intercepted and propagated to
VMCB01 instead of VMCB02. However, LBRV is only enabled in VMCB02 when
L2 is running.
This means that if L2 enables LBR and exits to L1, the LBRs will not be
propagated from VMCB02 to VMCB01, because LBRV is disabled in VMCB01.
There is no meaningful difference in CPUID rate in L2 when copying LBRs
on every nested transition vs. the current approach, so do the simple
and correct thing and always copy LBRs between VMCB01 and VMCB02 on
nested transitions (when LBRV is disabled by L1). Drop the conditional
LBRs copying in __svm_{enable/disable}_lbrv() as it is now unnecessary.
VMCB02 becomes the only source of truth for LBRs when L2 is running,
regardless of LBRV being enabled by L1, drop svm_get_lbr_vmcb() and use
svm->vmcb directly in its place.
Fixes: 1d5a1b5860 ("KVM: x86: nSVM: correctly virtualize LBR msrs when L2 is running")
Cc: stable@vger.kernel.org
Signed-off-by: Yosry Ahmed <yosry.ahmed@linux.dev>
Link: https://patch.msgid.link/20251108004524.1600006-4-yosry.ahmed@linux.dev
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
svm_update_lbrv() is called when MSR_IA32_DEBUGCTLMSR is updated, and on
nested transitions where LBRV is used. It checks whether LBRV enablement
needs to be changed in the current VMCB, and if it does, it also
recalculate intercepts to LBR MSRs.
However, there are cases where intercepts need to be updated even when
LBRV enablement doesn't. Example scenario:
- L1 has MSR_IA32_DEBUGCTLMSR cleared.
- L1 runs L2 without LBR_CTL_ENABLE (no LBRV).
- L2 sets DEBUGCTLMSR_LBR in MSR_IA32_DEBUGCTLMSR, svm_update_lbrv()
sets LBR_CTL_ENABLE in VMCB02 and disables intercepts to LBR MSRs.
- L2 exits to L1, svm_update_lbrv() is not called on this transition.
- L1 clears MSR_IA32_DEBUGCTLMSR, svm_update_lbrv() finds that
LBR_CTL_ENABLE is already cleared in VMCB01 and does nothing.
- Intercepts remain disabled, L1 reads to LBR MSRs read the host MSRs.
Fix it by always recalculating intercepts in svm_update_lbrv().
Fixes: 1d5a1b5860 ("KVM: x86: nSVM: correctly virtualize LBR msrs when L2 is running")
Cc: stable@vger.kernel.org
Signed-off-by: Yosry Ahmed <yosry.ahmed@linux.dev>
Link: https://patch.msgid.link/20251108004524.1600006-3-yosry.ahmed@linux.dev
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The APM lists the DbgCtlMsr field as being tracked by the VMCB_LBR clean
bit. Always clear the bit when MSR_IA32_DEBUGCTLMSR is updated.
The history is complicated, it was correctly cleared for L1 before
commit 1d5a1b5860 ("KVM: x86: nSVM: correctly virtualize LBR msrs when
L2 is running"). At that point svm_set_msr() started to rely on
svm_update_lbrv() to clear the bit, but when nested virtualization
is enabled the latter does not always clear it even if MSR_IA32_DEBUGCTLMSR
changed. Go back to clearing it directly in svm_set_msr().
Fixes: 1d5a1b5860 ("KVM: x86: nSVM: correctly virtualize LBR msrs when L2 is running")
Reported-by: Matteo Rizzo <matteorizzo@google.com>
Reported-by: evn@google.com
Co-developed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Yosry Ahmed <yosry.ahmed@linux.dev>
Link: https://patch.msgid.link/20251108004524.1600006-2-yosry.ahmed@linux.dev
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM x86 fixes for 6.18:
- Inject #UD if the guest attempts to execute SEAMCALL or TDCALL as KVM
doesn't support virtualization the instructions, but the instructions
are gated only by VMXON, i.e. will VM-Exit instead of taking a #UD and
thus result in KVM exiting to userspace with an emulation error.
- Unload the "FPU" when emulating INIT of XSTATE features if and only if
the FPU is actually loaded, instead of trying to predict when KVM will
emulate an INIT (CET support missed the MP_STATE path). Add sanity
checks to detect and harden against similar bugs in the future.
- Unregister KVM's GALog notifier (for AVIC) when kvm-amd.ko is unloaded.
- Use a raw spinlock for svm->ir_list_lock as the lock is taken during
schedule(), and "normal" spinlocks are sleepable locks when PREEMPT_RT=y.
- Remove guest_memfd bindings on memslot deletion when a gmem file is dying
to fix a use-after-free race found by syzkaller.
- Fix a goof in the EPT Violation handler where KVM checks the wrong
variable when determining if the reported GVA is valid.
KVM/riscv fixes for 6.18, take #2
- Fix check for local interrupts on riscv32
- Read HGEIP CSR on the correct cpu when checking for IMSIC interrupts
- Remove automatic I/O mapping from kvm_arch_prepare_memory_region()
If the allocation of tl_hba->sh fails in tcm_loop_driver_probe() and we
attempt to dereference it in tcm_loop_tpg_address_show() we will get a
segfault, see below for an example. So, check tl_hba->sh before
dereferencing it.
Unable to allocate struct scsi_host
BUG: kernel NULL pointer dereference, address: 0000000000000194
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 1 PID: 8356 Comm: tokio-runtime-w Not tainted 6.6.104.2-4.azl3 #1
Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.1 09/28/2024
RIP: 0010:tcm_loop_tpg_address_show+0x2e/0x50 [tcm_loop]
...
Call Trace:
<TASK>
configfs_read_iter+0x12d/0x1d0 [configfs]
vfs_read+0x1b5/0x300
ksys_read+0x6f/0xf0
...
Cc: stable@vger.kernel.org
Fixes: 2628b352c3 ("tcm_loop: Show address of tpg in configfs")
Signed-off-by: Hamza Mahfooz <hamzamahfooz@linux.microsoft.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Allen Pais <apais@linux.microsoft.com>
Link: https://patch.msgid.link/1762370746-6304-1-git-send-email-hamzamahfooz@linux.microsoft.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Zenghui reports that running a KVM guest with an assigned device and
lockdep enabled produces an unfriendly splat due to an inconsistent irq
context when taking the lpi_xa's spinlock.
This is no good as in rare cases the last reference to an LPI can get
dropped after injection of a cached LPI translation. In this case,
vgic_put_irq() will release the IRQ struct and take the lpi_xa's
spinlock to erase it from the xarray.
Reinstate the IRQ ordering and update the lockdep hint accordingly. Note
that there is no irqsave equivalent of might_lock(), so just explictly
grab and release the spinlock on lockdep kernels.
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Closes: https://lore.kernel.org/kvmarm/b4d7cb0f-f007-0b81-46d1-998b15cc14bc@huawei.com/
Fixes: 982f31bbb5 ("KVM: arm64: vgic-v3: Don't require IRQs be disabled for LPI xarray lock")
Signed-off-by: Oliver Upton <oupton@kernel.org>
Link: https://patch.msgid.link/20251107184847.1784820-2-oupton@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Now that the idreg's GIC field is in sync with the irqchip, limit
the runtime clearing of these fields to the pathological case where
we do not have an in-kernel GIC.
While we're at it, use the existing API instead of open-coded
accessors to access the ID regs.
Fixes: 5cb57a1aff ("KVM: arm64: Zero ID_AA64PFR0_EL1.GIC when no GICv3 is presented to the guest")
Reviewed-by: Oliver Upton <oupton@kernel.org>
Link: https://patch.msgid.link/20251030122707.2033690-4-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
32bit ID registers aren't getting much love these days, and are
often missed in updates. One of these updates broke restoring
a GICv2 guest on a GICv3 machine.
Instead of performing a piecemeal fix, just bite the bullet
and make all 32bit ID regs fully writable. KVM itself never
relies on them for anything, and if the VMM wants to mess up
the guest, so be it.
Fixes: 5cb57a1aff ("KVM: arm64: Zero ID_AA64PFR0_EL1.GIC when no GICv3 is presented to the guest")
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Cc: stable@vger.kernel.org
Reviewed-by: Oliver Upton <oupton@kernel.org>
Link: https://patch.msgid.link/20251030122707.2033690-2-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
It seems that most of the tests prepare the interfaces once before the test
run (setup_prepare()), rely on setup_wait() to wait for link and only then
run the test(s).
local_termination brings the physical interfaces down and up during test
run but never wait for them to come up. If the auto-negotiation takes
some seconds, first test packets are being lost, which leads to
false-negative test results.
Use setup_wait() in run_test() to make sure auto-negotiation has been
completed after all simple_if_init() calls on physical interfaces and test
packets will not be lost because of the race against link establishment.
Fixes: 90b9566aa5 ("selftests: forwarding: add a test for local_termination.sh")
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://patch.msgid.link/20251106161213.459501-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The `len` member of the sk_buff is an unsigned int. This is cast to
`ssize_t` (a signed type) for the first sk_buff in the comparison,
but not the second sk_buff. On 32-bit systems, this can result in
an integer underflow for certain values because unsigned arithmetic
is being used.
This appears to be an oversight: if the intention was to use unsigned
arithmetic, then the first cast would have been omitted. The change
ensures both len values are cast to `ssize_t`.
The underflow causes an issue with ktls when multiple TLS PDUs are
included in a single TCP segment. The mainline kernel does not use
strparser for ktls anymore, but this is still useful for other
features that still use strparser, and for backporting.
Signed-off-by: Nate Karstens <nate.karstens@garmin.com>
Cc: stable@vger.kernel.org
Fixes: 43a0c6751a ("strparser: Stream parser for messages")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20251106222835.1871628-1-nate.karstens@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 44aa25c000 ("riscv: asm: use .insn for making custom
instructions"), builds using LLVM older that 19 or binutils older than
2.38 fail with:
arch/riscv/include/asm/vdso/processor.h: Assembler messages:
arch/riscv/include/asm/vdso/processor.h:27: Error: unrecognized opcode `0x100000f'
arch/riscv/include/asm/vdso/processor.h:27: Error: unrecognized opcode `0x100000f'
arch/riscv/include/asm/vdso/processor.h:27: Error: unrecognized opcode `0x100000f'
arch/riscv/include/asm/vdso/processor.h:27: Error: unrecognized opcode `0x100000f'
make[4]: *** [scripts/Makefile.build:287: arch/riscv/kernel/vdso/vgettimeofday.o] Error 1
In file included from <built-in>:4:
In file included from lib/vdso/gettimeofday.c:6:
In file included from include/vdso/datapage.h:21:
In file included from include/vdso/processor.h:10:
arch/riscv/include/asm/vdso/processor.h:23:2: error: expected instruction format
23 | ALT_RISCV_PAUSE();
| ^
arch/riscv/include/asm/errata_list.h:47:3: note: expanded from macro 'ALT_RISCV_PAUSE'
47 | RISCV_PAUSE, /* Original RISC‑V pause insn */ \
| ^
arch/riscv/include/asm/insn-def.h:259:21: note: expanded from macro 'RISCV_PAUSE'
259 | #define RISCV_PAUSE ASM_INSN_I("0x100000f")
| ^
arch/riscv/include/asm/asm.h:16:26: note: expanded from macro 'ASM_INSN_I'
16 | #define ASM_INSN_I(__x) ".insn " __x
| ^
<inline asm>:5:7: note: instantiated into assembly here
5 | .insn 0x100000f
| ^
binutils gained support for '.insn <value>' in 2.38 [1] and LLVM gained
support in 19 [2]. Adjust the test for CONFIG_AS_HAS_INSN to ensure that
all versions of .insn are supported before being used.
Fixes: 44aa25c000 ("riscv: asm: use .insn for making custom instructions")
Link: https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=a262b82fdbf4cda3b0648b1adc32245ca3f78b7a [1]
Link: 2a086dce69 [2]
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://patch.msgid.link/20251107-riscv-fix-new-insn-usage-v1-1-9a186c5928a0@kernel.org
Signed-off-by: Paul Walmsley <pjw@kernel.org>
Add proper error handling and resource cleanup to prevent memory leaks
in add_boot_memory_ranges(). The function now checks for NULL return
from kobject_create_and_add(), uses local buffer for range names to
avoid dynamic allocation, and implements a cleanup path that removes
previously created sysfs groups and kobjects on failure.
This prevents resource leaks when kobject creation or sysfs group
creation fails during boot memory range initialization.
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://patch.msgid.link/20251030023228.3956296-1-kaushlendra.kumar@intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
per_cpu(cpc_desc_ptr, cpu) object is initialized for only the online
CPU via acpi_soft_cpu_online() --> __acpi_processor_start() -->
acpi_cppc_processor_probe().
However the function cppc_perf_ctrs_in_pcc() checks if the CPPC
perf-ctrs are in a PCC region for all the present CPUs, which breaks
when the kernel is booted with "nosmt=force".
Hence, limit the check only to the online CPUs.
Fixes: ae2df912d1 ("ACPI: CPPC: Disable FIE if registers in PCC regions")
Reviewed-by: "Mario Limonciello (AMD) (kernel.org)" <superm1@kernel.org>
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://patch.msgid.link/20251107074145.2340-5-gautham.shenoy@amd.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
per_cpu(cpc_desc_ptr, cpu) object is initialized for only the online
CPUs via acpi_soft_cpu_online() --> __acpi_processor_start() -->
acpi_cppc_processor_probe().
However the function cppc_allow_fast_switch() checks for the validity
of the _CPC object for all the present CPUs. This breaks when the
kernel is booted with "nosmt=force".
Check fast_switch capability only on online CPUs
Fixes: 15eece6c5b ("ACPI: CPPC: Fix NULL pointer dereference when nosmp is used")
Reviewed-by: "Mario Limonciello (AMD) (kernel.org)" <superm1@kernel.org>
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://patch.msgid.link/20251107074145.2340-4-gautham.shenoy@amd.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The HPA to DPA translation for poison injection assumes that the
base address starts from where the CXL region begins. When the
extended linear cache is active, the offset can be within the DRAM
region. Adjust the offset so that it correctly reflects the offset
within the CXL region.
[ dj: Add fixes tag from Alison ]
Fixes: c3dd67681c ("cxl/region: Add inject and clear poison by region offset")
Link: https://patch.msgid.link/20251031173224.3537030-5-dave.jiang@intel.com
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Disallow a module to load if SCS dynamic patching fails for its code. For
module loading, instead of running a dry-run to check for patching errors,
try to run patching in the first run and propagate any errors so module
loading will fail.
Signed-off-by: Adrian Barnaś <abarnas@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Following the pattern established with other Spectre mitigations,
do not print a message when the CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
Kconfig option is disabled.
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: shechenglong <shechenglong@xfusion.com>
Signed-off-by: Will Deacon <will@kernel.org>
Tidy up the implementation of force_pte_mapping() to make it easier to
read and introduce the split_leaf_mapping_possible() helper to reduce
code duplication in split_kernel_leaf_mapping() and
arch_kfence_init_pool().
Suggested-by: David Hildenbrand (Red Hat) <david@kernel.org>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: David Hildenbrand (Red Hat) <david@kernel.org>
Reviewed-by: Yang Shi <yang@os.amperecomputing.com>
Signed-off-by: Will Deacon <will@kernel.org>
Enter lazy_mmu mode while splitting a range of memory to pte mappings.
This causes barriers, which would otherwise be emitted after every pte
(and pmd/pud) write, to be deferred until exiting lazy_mmu mode.
For large systems, this is expected to significantly speed up fallback
to pte-mapping the linear map for the case where the boot CPU has
BBML2_NOABORT, but secondary CPUs do not. I haven't directly measured
it, but this is equivalent to commit 1fcb7cea8a ("arm64: mm: Batch dsb
and isb when populating pgtables").
Note that for the path from arch_kfence_init_pool(), we may sleep while
allocating memory inside the lazy_mmu mode. Sleeping is not allowed by
generic code inside lazy_mmu, but we know that the arm64 implementation
is sleep-safe. So this is ok and follows the same pattern already used
by split_kernel_leaf_mapping().
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Yang Shi <yang@os.amperecomputing.com>
Signed-off-by: Will Deacon <will@kernel.org>
It has been reported that split_kernel_leaf_mapping() is trying to sleep
in non-sleepable context. It does this when acquiring the
pgtable_split_lock mutex, when either CONFIG_DEBUG_PAGEALLOC or
CONFIG_KFENCE are enabled, which change linear map permissions within
softirq context during memory allocation and/or freeing. All other paths
into this function are called from sleepable context and so are safe.
But it turns out that the memory for which these 2 features may attempt
to modify the permissions is always mapped by pte, so there is no need
to attempt to split the mapping. So let's exit early in these cases and
avoid attempting to take the mutex.
There is one wrinkle to this approach; late-initialized kfence allocates
it's pool from the buddy which may be block mapped. So we must hook that
allocation and convert it to pte-mappings up front. Previously this was
done as a side-effect of kfence protecting all the individual pages in
its pool at init-time, but this no longer works due to the added early
exit path in split_kernel_leaf_mapping().
So instead, do this via the existing arch_kfence_init_pool() arch hook,
and reuse the existing linear_map_split_to_ptes() infrastructure.
Closes: https://lore.kernel.org/all/f24b9032-0ec9-47b1-8b95-c0eeac7a31c5@roeck-us.net/
Fixes: a166563e7e ("arm64: mm: support large block mapping when rodata=full")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <groeck@google.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: David Hildenbrand (Red Hat) <david@kernel.org>
Reviewed-by: Yang Shi <yang@os.amperecomputing.com>
Signed-off-by: Will Deacon <will@kernel.org>
Since commit a166563e7e ("arm64: mm: support large block mapping when
rodata=full"), __change_memory_common has more chance to fail due to
memory allocation failure when splitting page table. So check the return
value of set_memory_rox(), then bail out if it fails otherwise we may have
RW memory mapping for kprobes insn page.
Fixes: 195a1b7d83 ("arm64: kprobes: call set_memory_rox() for kprobe page")
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Dev Jain <dev.jain@arm.com>
Signed-off-by: Yang Shi <yang@os.amperecomputing.com>
Signed-off-by: Will Deacon <will@kernel.org>
Commit f5a4af3c75 ("ACPI: Add acpi=nospcr to disable ACPI SPCR as
default console on ARM64") introduced a command line parameter to
prevent using SPCR provided console as default. It also introduced a
message to log this choice.
Drop the message as it is not particularly useful and can be incorrect
in situations where no SPCR is provided by the firmware.
Link: https://lore.kernel.org/all/aQN0YWUYaPYWpgJM@willie-the-truck/
Signed-off-by: Punit Agrawal <punit.agrawal@oss.qualcomm.com>
Signed-off-by: Will Deacon <will@kernel.org>
This reverts commit bad3fa2fb9.
Commit bad3fa2fb9 ("ACPI: Suppress misleading SPCR console message
when SPCR table is absent") mistakenly assumes acpi_parse_spcr()
returning 0 to indicate a failure to parse SPCR. While addressing the
resultant incorrect logging it was deemed that dropping the message is
a better approach as it is not particularly useful.
Roll back the commit introducing the bug as a step towards dropping
the log message.
Link: https://lore.kernel.org/all/aQN0YWUYaPYWpgJM@willie-the-truck/
Signed-off-by: Punit Agrawal <punit.agrawal@oss.qualcomm.com>
Signed-off-by: Will Deacon <will@kernel.org>
The non-return per-CPU this_cpu_*() atomic operations are implemented as
STADD/STCLR/STSET when FEAT_LSE is available. On many microarchitecture
implementations, these instructions tend to be executed "far" in the
interconnect or memory subsystem (unless the data is already in the L1
cache). This is in general more efficient when there is contention as it
avoids bouncing cache lines between CPUs. The load atomics (e.g. LDADD
without XZR as destination), OTOH, tend to be executed "near" with the
data loaded into the L1 cache.
STADD executed back to back as in srcu_read_{lock,unlock}*() incur an
additional overhead due to the default posting behaviour on several CPU
implementations. Since the per-CPU atomics are unlikely to be used
concurrently on the same memory location, encourage the hardware to to
execute them "near" by issuing load atomics - LDADD/LDCLR/LDSET - with
the destination register unused (but not XZR).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/e7d539ed-ced0-4b96-8ecd-048a5b803b85@paulmck-laptop
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Palmer Dabbelt <palmer@dabbelt.com>
[will: Add comment and link to the discussion thread]
Signed-off-by: Will Deacon <will@kernel.org>
SPI devices using a (relative) slow frequency need a larger time.
For instance, microblaze running at 83.25MHz and performing a
3 bytes transaction using a 10MHz/16 = 625kHz needed this stall
value increased to at least 20. The SPI device is quite slow, but
also is the microblaze, so set this value to 32 to give it even
more margin.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://patch.msgid.link/20251106134545.31942-1-alvaro.gamez@hazent.com
Signed-off-by: Mark Brown <broonie@kernel.org>
While connecting, the MAC address can already no longer be
changed. The change is already rejected if netif_carrier_ok(),
but of course that's not true yet while connecting. Check for
auth_data or assoc_data, so the MAC address cannot be changed.
Also more comprehensively check that there are no stations on
the interface being changed - if any peer station is added it
will know about our address already, so we cannot change it.
Cc: stable@vger.kernel.org
Fixes: 3c06e91b40 ("wifi: mac80211: Support POWERED_ADDR_CHANGE feature")
Link: https://patch.msgid.link/20251105154119.f9f6c1df81bb.I9bb3760ede650fb96588be0d09a5a7bdec21b217@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the commit referenced by the Fixes tag, clk_hw_get_clk()
was added in va_macro_probe() to get the fsgen clock,
but forgot to add the corresponding clk_put() in va_macro_remove().
This leads to a clock reference leak when the driver is unloaded.
Switch to devm_clk_hw_get_clk() to automatically manage the
clock resource.
Fixes: 30097967e0 ("ASoC: codecs: va-macro: use fsgen as clock")
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20251106143114.729-1-vulab@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
When reporting tx completion using ieee80211_tx_status_xxx() family of
functions, the status part of the struct ieee80211_tx_info nested in the
skb is used to report things like transmit rates & retry count to mac80211
On the TX data path, this is correctly memset to 0 before calling
ieee80211_tx_status_ext(), but on the tx mgmt path this was not done.
This leads to mac80211 treating garbage values as valid transmit counters
(like tx retries for example) and accounting them as real statistics that
makes their way to userland via station dump.
The same issue was resolved in ath12k by commit 9903c0986f ("wifi:
ath12k: Add memset and update default rate value in wmi tx completion")
Tested-on: QCN9074 PCI WLAN.HK.2.9.0.1-01977-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251104083957.717825-1-nico.escande@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Since sdma hardware configure postpone to transfer phase, have to disable
dma request before dma transfer setup because there is a hardware
limitation on sdma event enable(ENBLn) as below:
"It is thus essential for the Arm platform to program them before any DMA
request is triggered to the SDMA, otherwise an unpredictable combination
of channels may be started."
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://patch.msgid.link/20251024055320.408482-1-carlos.song@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The bus_find_device_by_name() function returns a device pointer with an
incremented reference count, but the original code was missing put_device()
calls in some return paths, leading to reference count leaks.
Fix this by ensuring put_device() is called before function exit after
bus_find_device_by_name() succeeds
This follows the same pattern used elsewhere in the kernel where
bus_find_device_by_name() is properly paired with put_device().
Found via static analysis and code review.
Fixes: 4f8ef33dd4 ("ASoC: soc_sdw_utils: skip the endpoint that doesn't present")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://patch.msgid.link/20251029071804.8425-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function enables regulators at the beginning
but fails to disable them in its error handling path.
If any operation after enabling the regulators fails,
the probe will exit with an error, leaving the regulators
permanently enabled, which could lead to a resource leak.
Add a proper error handling path to call regulator_bulk_disable()
before returning an error.
Fixes: 9a397f4736 ("ASoC: cs4271: add regulator consumer support")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20251105062246.1955-1-vulab@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix all kernel-doc warnings in <uapi/linux/isst_if.h>:
- don't use "[]" in the variable name in kernel-doc
- add a few missing entries
- change "power_domain" to "power_domain_id" in kernel-doc to match
the struct member name
- add a leading '@' on a few existing kernel-doc lines
- use '_' instead of '-' in struct member names
Examples (but not all 27 warnings):
Warning: include/uapi/linux/isst_if.h:63 struct member 'cpu_map'
not described in 'isst_if_cpu_maps'
Warning: ../include/uapi/linux/isst_if.h:95 struct member 'req_count'
not described in 'isst_if_io_regs'
Warning: include/uapi/linux/isst_if.h:132 struct member 'mbox_cmd'
not described in 'isst_if_mbox_cmds'
Warning: ../include/uapi/linux/isst_if.h:183 struct member 'supported'
not described in 'isst_core_power'
Warning: ../include/uapi/linux/isst_if.h:206 struct member
'power_domain_id' not described in 'isst_clos_param'
Warning: ../include/uapi/linux/isst_if.h:239 struct member 'assoc_info'
not described in 'isst_if_clos_assoc_cmds'
Warning: ../include/uapi/linux/isst_if.h:286 struct member 'sst_tf_support'
not described in 'isst_perf_level_info'
Warning: ../include/uapi/linux/isst_if.h:375 struct member 'trl_freq_mhz'
not described in 'isst_perf_level_data_info'
Warning: ../include/uapi/linux/isst_if.h:475 struct member 'max_buckets'
not described in 'isst_turbo_freq_info'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20251023194615.180824-1-rdunlap@infradead.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The newer HP Omen laptops, such as Omen 16-wf1xxx, use the same
WMI-based thermal profile interface as Victus 16-r1000 and 16-s1000
models.
Add the DMI board name "8C78" to the victus_s_thermal_profile_boards
list to enable proper fan and thermal mode control.
Tested on: HP Omen 16-wf1xxx (board 8C78)
Result:
* Fan RPMs are readable
* echo 0 | sudo tee /sys/devices/platform/hp-wmi/hwmon/*/pwm1_enable
allows the fans to run on max RPM.
Signed-off-by: Krishna Chomal <krishna.chomal108@gmail.com>
Link: https://patch.msgid.link/20251018111001.56625-1-krishna.chomal108@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
After restructuring and splitting the HDMI codec driver code, each
HDMI codec driver contains the own build_controls and build_pcms ops.
A copy-n-paste error put the wrong entries for nvhdmi-mcp driver; both
build_controls and build_pcms are swapped. Unfortunately both
callbacks have the very same form, and the compiler didn't complain
it, either. This resulted in a NULL dereference because the PCM
instance hasn't been initialized at calling the build_controls
callback.
Fix it by passing the proper entries.
Fixes: ad781b550f ("ALSA: hda/hdmi: Rewrite to new probe method")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220743
Link: https://patch.msgid.link/20251106104647.25805-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The qm_get_qos_value() function calls bus_find_device_by_name() which
increases the device reference count, but fails to call put_device()
to balance the reference count and lead to a device reference leak.
Add put_device() calls in both the error path and success path to
properly balance the reference count.
Found via static analysis.
Fixes: 22d7a6c39c ("crypto: hisilicon/qm - add pci bdf number check")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Adding test that attaches kprobe/kretprobe multi and verifies the
ORC stacktrace matches expected functions.
Adding bpf_testmod_stacktrace_test function to bpf_testmod kernel
module which is called through several functions so we get reliable
call path for stacktrace.
The test is only for ORC unwinder to keep it simple.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20251104215405.168643-4-jolsa@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Currently we don't get stack trace via ORC unwinder on top of fgraph exit
handler. We can see that when generating stacktrace from kretprobe_multi
bpf program which is based on fprobe/fgraph.
The reason is that the ORC unwind code won't get pass the return_to_handler
callback installed by fgraph return probe machinery.
Solving this by creating stack frame in return_to_handler expected by
ftrace_graph_ret_addr function to recover original return address and
continue with the unwind.
Also updating the pt_regs data with cs/flags/rsp which are needed for
successful stack retrieval from ebpf bpf_get_stackid helper.
- in get_perf_callchain we check user_mode(regs) so CS has to be set
- in perf_callchain_kernel we call perf_hw_regs(regs), so EFLAGS/FIXED
has to be unset
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20251104215405.168643-3-jolsa@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
This reverts commit 83f44ae0f8.
Currently we store initial stacktrace entry twice for non-HW ot_regs, which
means callers that fail perf_hw_regs(regs) condition in perf_callchain_kernel.
It's easy to reproduce this bpftrace:
# bpftrace -e 'tracepoint:sched:sched_process_exec { print(kstack()); }'
Attaching 1 probe...
bprm_execve+1767
bprm_execve+1767
do_execveat_common.isra.0+425
__x64_sys_execve+56
do_syscall_64+133
entry_SYSCALL_64_after_hwframe+118
When perf_callchain_kernel calls unwind_start with first_frame, AFAICS
we do not skip regs->ip, but it's added as part of the unwind process.
Hence reverting the extra perf_callchain_store for non-hw regs leg.
I was not able to bisect this, so I'm not really sure why this was needed
in v5.2 and why it's not working anymore, but I could see double entries
as far as v5.10.
I did the test for both ORC and framepointer unwind with and without the
this fix and except for the initial entry the stacktraces are the same.
Acked-by: Song Liu <song@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20251104215405.168643-2-jolsa@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
data_reloc_print_warning_inode() calls btrfs_get_fs_root() to obtain
local_root, but fails to release its reference when paths_from_inode()
returns an error. This causes a potential memory leak.
Add a missing btrfs_put_root() call in the error path to properly
decrease the reference count of local_root.
Fixes: b9a9a85059 ("btrfs: output affected files when relocation fails")
CC: stable@vger.kernel.org # 6.6+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
scrub_raid56_parity_stripe() allocates a bio with bio_alloc(), but
fails to release it on some error paths, leading to a potential
memory leak.
Add the missing bio_put() calls to properly drop the bio reference
in those error cases.
Fixes: 1009254bf2 ("btrfs: scrub: use scrub_stripe to implement RAID56 P/Q scrub")
CC: stable@vger.kernel.org # 6.6+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When logging that a new name exists, we skip updating the inode's
last_log_commit field to prevent a later explicit fsync against the inode
from doing nothing (as updating last_log_commit makes btrfs_inode_in_log()
return true). We are detecting, at btrfs_log_inode(), that logging a new
name is happening by checking the logging mode is not LOG_INODE_EXISTS,
but that is not enough because we may log parent directories when logging
a new name of a file in LOG_INODE_ALL mode - we need to check that the
logging_new_name field of the log context too.
An example scenario where this results in an explicit fsync against a
directory not persisting changes to the directory is the following:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ touch /mnt/foo
$ sync
$ mkdir /mnt/dir
# Write some data to our file and fsync it.
$ xfs_io -c "pwrite -S 0xab 0 64K" -c "fsync" /mnt/foo
# Add a new link to our file. Since the file was logged before, we
# update it in the log tree by calling btrfs_log_new_name().
$ ln /mnt/foo /mnt/dir/bar
# fsync the root directory - we expect it to persist the dentry for
# the new directory "dir".
$ xfs_io -c "fsync" /mnt
<power fail>
After mounting the fs the entry for directory "dir" does not exists,
despite the explicit fsync on the root directory.
Here's why this happens:
1) When we fsync the file we log the inode, so that it's present in the
log tree;
2) When adding the new link we enter btrfs_log_new_name(), and since the
inode is in the log tree we proceed to updating the inode in the log
tree;
3) We first set the inode's last_unlink_trans to the current transaction
(early in btrfs_log_new_name());
4) We then eventually enter btrfs_log_inode_parent(), and after logging
the file's inode, we call btrfs_log_all_parents() because the inode's
last_unlink_trans matches the current transaction's ID (updated in the
previous step);
5) So btrfs_log_all_parents() logs the root directory by calling
btrfs_log_inode() for the root's inode with a log mode of LOG_INODE_ALL
so that new dentries are logged;
6) At btrfs_log_inode(), because the log mode is LOG_INODE_ALL, we
update root inode's last_log_commit to the last transaction that
changed the inode (->last_sub_trans field of the inode), which
corresponds to the current transaction's ID;
7) Then later when user space explicitly calls fsync against the root
directory, we enter btrfs_sync_file(), which calls skip_inode_logging()
and that returns true, since its call to btrfs_inode_in_log() returns
true and there are no ordered extents (it's a directory, never has
ordered extents). This results in btrfs_sync_file() returning without
syncing the log or committing the current transaction, so all the
updates we did when logging the new name, including logging the root
directory, are not persisted.
So fix this by but updating the inode's last_log_commit if we are sure
we are not logging a new name (if ctx->logging_new_name is false).
A test case for fstests will follow soon.
Reported-by: Vyacheslav Kovalevsky <slava.kovalevskiy.2014@gmail.com>
Link: https://lore.kernel.org/linux-btrfs/03c5d7ec-5b3d-49d1-95bc-8970a7f82d87@gmail.com/
Fixes: 130341be7f ("btrfs: always update the logged transaction when logging new names")
CC: stable@vger.kernel.org # 6.1+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The stripe offset calculation in the zoned code for raid0 and raid10
wrongly uses map->stripe_size to calculate it. In fact, map->stripe_size is
the size of the device extent composing the block group, which always is
the zone_size on the zoned setup.
Fix it by using BTRFS_STRIPE_LEN and BTRFS_STRIPE_LEN_SHIFT. Also, optimize
the calculation a bit by doing the common calculation only once.
Fixes: c0d90a79e8 ("btrfs: zoned: fix alloc_offset calculation for partly conventional block groups")
CC: stable@vger.kernel.org # 6.17+
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When a block group contains both conventional zone and sequential zone, the
capacity of the block group is wrongly set to the block group's full
length. The capacity should be calculated in btrfs_load_block_group_* using
the last allocation offset.
Fixes: 568220fa96 ("btrfs: zoned: support RAID0/1/10 on top of raid stripe tree")
CC: stable@vger.kernel.org # v6.12+
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In Raspberry Pi 5 DTS, the Ethernet clock rates must be assigned
as the default clock register values are not valid for the
Ethernet interface to function.
This can be done either in rp1_clocks node or in rp1_eth node.
Define the rates in rp1_eth node, as those clocks are 'leaf' clocks
used specifically by the Ethernet device only.
Fixes: 43456fdfc0 ("arm64: dts: broadcom: Enable RP1 ethernet for Raspberry Pi 5")
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Link: https://lore.kernel.org/r/20251021135533.5517-1-andrea.porta@suse.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
As per the i.MX8MP TRM, section 14.2 "AUDIO_BLK_CTRL", table 14.2.3.1.1
"memory map", the definition of the EARC control register shows that the
EARC controller software reset is controlled via bit 0, while the EARC PHY
software reset is controlled via bit 1.
This means that the current definitions of IMX8MP_AUDIOMIX_EARC_RESET_MASK
and IMX8MP_AUDIOMIX_EARC_PHY_RESET_MASK are wrong since their values would
imply that the EARC controller software reset is controlled via bit 1 and
the EARC PHY software reset is controlled via bit 2. Fix them.
Fixes: a83bc87cd3 ("reset: imx8mp-audiomix: Prepare the code for more reset bits")
Cc: stable@vger.kernel.org
Reviewed-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Since commit d24cfee7f6 ("spi: Fix acpi deferred irq probe"), the
acpi_dev_gpio_irq_get() call gets delayed till spi_probe() is called
on the SPI device.
If there is no driver for the SPI device then the move to spi_probe()
results in acpi_dev_gpio_irq_get() never getting called. This may
cause problems by leaving the GPIO pin floating because this call is
responsible for setting up the GPIO pin direction and/or bias according
to the values from the ACPI tables.
Re-add the removed acpi_dev_gpio_irq_get() in acpi_register_spi_device()
to ensure the GPIO pin is always correctly setup, while keeping the
acpi_dev_gpio_irq_get() call added to spi_probe() to deal with
-EPROBE_DEFER returns caused by the GPIO controller not having a driver
yet.
Link: https://bbs.archlinux.org/viewtopic.php?id=302348
Fixes: d24cfee7f6 ("spi: Fix acpi deferred irq probe")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hansg@kernel.org>
Link: https://patch.msgid.link/20251102190921.30068-1-hansg@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
bm_register_write() opens an executable file using open_exec(), which
internally calls do_open_execat() and denies write access on the file to
avoid modification while it is being executed.
However, when an error occurs, bm_register_write() closes the file using
filp_close() directly. This does not restore the write permission, which
may cause subsequent write operations on the same file to fail.
Fix this by calling exe_file_allow_write_access() before filp_close() to
restore the write permission properly.
Fixes: e7850f4d84 ("binfmt_misc: fix possible deadlock in bm_register_write")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Link: https://patch.msgid.link/20251105022923.1813587-1-zilin@seu.edu.cn
Signed-off-by: Christian Brauner <brauner@kernel.org>
When sb_min_blocksize() returns 0 and the return value is not checked,
it may lead to a situation where sb->s_blocksize is 0 when
accessing the filesystem super block. After commit a64e5a5960
("bdev: add back PAGE_SIZE block size validation for
sb_set_blocksize()"), this becomes more likely to happen when the
block device’s logical_block_size is larger than PAGE_SIZE and the
filesystem is unformatted. Add the __must_check attribute to ensure
callers always check the return value.
Cc: stable@vger.kernel.org # v6.15
Suggested-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Yongpeng Yang <yangyongpeng@xiaomi.com>
Link: https://patch.msgid.link/20251104125009.2111925-6-yangyongpeng.storage@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
In the commit referenced by the Fixes tag,
devm_gpiod_get_optional() was replaced by manual
GPIO management, relying on the regulator core to release the
GPIO descriptor. However, this approach does not account for the
error path: when regulator registration fails, the core never
takes over the GPIO, resulting in a resource leak.
Add gpiod_put() before returning on regulator registration failure.
Fixes: 5e6f3ae5c1 ("regulator: fixed: Let core handle GPIO descriptor")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20251028172828.625-1-vulab@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Mykyta Yatsenko says:
====================
bpf: Add _impl suffix for kfuncs with implicit args
We have established a pattern of function naming win "_impl" suffix;
those functions accept verifier-provided bpf_prog_aux argument.
Following uniform convention will allow for transparent backwards
compatibility with the upcoming KF_IMPLICIT_ARGS feature. This patch
set aims to fix current deviation from the convention to eliminate
unnecessary backwards incompatibility in the future.
Three kfuncs added in 6.18 don’t follow this *_impl convention and
therefore won’t participate in the new KF_IMPLICIT_ARGS mechanism:
* bpf_task_work_schedule_resume()
* bpf_task_work_schedule_signal()
* bpf_stream_vprintk()
Rename them to align with the implicit-arg flow:
bpf_task_work_schedule_resume() -> bpf_task_work_schedule_resume_impl()
bpf_task_work_schedule_signal() -> bpf_task_work_schedule_signal_impl()
bpf_stream_vprintk() -> bpf_stream_vprintk_impl()
The KF_IMPLICIT_ARGS mechanism is not in tree yet, so callers must
switch to the *_impl names for now. Once the new mechanism lands, the
plain names (without _impl) will be reintroduced.
Signed-off-by: Mykyta Yatsenko <yatsenko@meta.com>
Acked-by: Ihor Solodrai <ihor.solodrai@linux.dev>
---
Changes in v3:
- Fix commit messages
- Link to v2: https://lore.kernel.org/r/20251104-implv2-v2-0-6dbc35f39f28@meta.com
Changes in v1:
- Split commit into 2
- Rebase on the correct branch
- Link to v1: https://lore.kernel.org/all/20251103232319.122965-1-mykyta.yatsenko5@gmail.com/
====================
Link: https://patch.msgid.link/20251104-implv2-v3-0-4772b9ae0e06@meta.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Rename bpf_stream_vprintk() to bpf_stream_vprintk_impl().
This makes bpf_stream_vprintk() follow the already established "_impl"
suffix-based naming convention for kfuncs with the bpf_prog_aux
argument provided by the verifier implicitly. This convention will be
taken advantage of with the upcoming KF_IMPLICIT_ARGS feature to
preserve backwards compatibility to BPF programs.
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Mykyta Yatsenko <yatsenko@meta.com>
Link: https://lore.kernel.org/r/20251104-implv2-v3-2-4772b9ae0e06@meta.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Rename:
bpf_task_work_schedule_resume()->bpf_task_work_schedule_resume_impl()
bpf_task_work_schedule_signal()->bpf_task_work_schedule_signal_impl()
This aligns task work scheduling kfuncs with the established naming
scheme for kfuncs with the bpf_prog_aux argument provided by the
verifier implicitly. This convention will be taken advantage of with the
upcoming KF_IMPLICIT_ARGS feature to preserve backwards compatibility to
BPF programs.
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Mykyta Yatsenko <yatsenko@meta.com>
Link: https://lore.kernel.org/r/20251104-implv2-v3-1-4772b9ae0e06@meta.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Ihor Solodrai <ihor.solodrai@linux.dev>
If cros_ec_keyb_register_matrix() isn't called (due to
`buttons_switches_only`) in cros_ec_keyb_probe(), `ckdev->idev` remains
NULL. An invalid memory access is observed in cros_ec_keyb_process()
when receiving an EC_MKBP_EVENT_KEY_MATRIX event in cros_ec_keyb_work()
in such case.
Unable to handle kernel read from unreadable memory at virtual address 0000000000000028
...
x3 : 0000000000000000 x2 : 0000000000000000
x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
input_event
cros_ec_keyb_work
blocking_notifier_call_chain
ec_irq_thread
It's still unknown about why the kernel receives such malformed event,
in any cases, the kernel shouldn't access `ckdev->idev` and friends if
the driver doesn't intend to initialize them.
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://patch.msgid.link/20251104070310.3212712-1-tzungbi@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The commit 4adc20ba95 ("ARM: dts: broadcom: rpi: Switch to V3D firmware
clock") causes a regression in arm64 developer setups, which stores the
kernel modules via NFS. Before this change the involved V3D clock provider
was builtin, but after this DT change the clk-raspberrypi is responsible
for V3D and for arm64/defconfig this driver is build as a kernel module.
In case these kernel modules are provided via NFS this takes too long and
the PM domain core give up before the clock driver could be loaded:
v3d fec00000.gpu: deferred probe timeout, ignoring dependency
So resolve this issue by making this critical driver builtin.
Reported-by: Mark Brown <broonie@kernel.org>
Closes: https://lore.kernel.org/linux-arm-kernel/9ebda74e-e700-4fbe-bca5-382f92417a9c@sirena.org.uk/
Fixes: 4adc20ba95 ("ARM: dts: broadcom: rpi: Switch to V3D firmware clock")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20251104174518.11783-1-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
When unbinding a memslot from a guest_memfd instance, remove the bindings
even if the guest_memfd file is dying, i.e. even if its file refcount has
gone to zero. If the memslot is freed before the file is fully released,
nullifying the memslot side of the binding in kvm_gmem_release() will
write to freed memory, as detected by syzbot+KASAN:
==================================================================
BUG: KASAN: slab-use-after-free in kvm_gmem_release+0x176/0x440 virt/kvm/guest_memfd.c:353
Write of size 8 at addr ffff88807befa508 by task syz.0.17/6022
CPU: 0 UID: 0 PID: 6022 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/02/2025
Call Trace:
<TASK>
dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xca/0x240 mm/kasan/report.c:482
kasan_report+0x118/0x150 mm/kasan/report.c:595
kvm_gmem_release+0x176/0x440 virt/kvm/guest_memfd.c:353
__fput+0x44c/0xa70 fs/file_table.c:468
task_work_run+0x1d4/0x260 kernel/task_work.c:227
resume_user_mode_work include/linux/resume_user_mode.h:50 [inline]
exit_to_user_mode_loop+0xe9/0x130 kernel/entry/common.c:43
exit_to_user_mode_prepare include/linux/irq-entry-common.h:225 [inline]
syscall_exit_to_user_mode_work include/linux/entry-common.h:175 [inline]
syscall_exit_to_user_mode include/linux/entry-common.h:210 [inline]
do_syscall_64+0x2bd/0xfa0 arch/x86/entry/syscall_64.c:100
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fbeeff8efc9
</TASK>
Allocated by task 6023:
kasan_save_stack mm/kasan/common.c:56 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:77
poison_kmalloc_redzone mm/kasan/common.c:397 [inline]
__kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:414
kasan_kmalloc include/linux/kasan.h:262 [inline]
__kmalloc_cache_noprof+0x3e2/0x700 mm/slub.c:5758
kmalloc_noprof include/linux/slab.h:957 [inline]
kzalloc_noprof include/linux/slab.h:1094 [inline]
kvm_set_memory_region+0x747/0xb90 virt/kvm/kvm_main.c:2104
kvm_vm_ioctl_set_memory_region+0x6f/0xd0 virt/kvm/kvm_main.c:2154
kvm_vm_ioctl+0x957/0xc60 virt/kvm/kvm_main.c:5201
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:583
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0xfa0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 6023:
kasan_save_stack mm/kasan/common.c:56 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:77
kasan_save_free_info+0x46/0x50 mm/kasan/generic.c:584
poison_slab_object mm/kasan/common.c:252 [inline]
__kasan_slab_free+0x5c/0x80 mm/kasan/common.c:284
kasan_slab_free include/linux/kasan.h:234 [inline]
slab_free_hook mm/slub.c:2533 [inline]
slab_free mm/slub.c:6622 [inline]
kfree+0x19a/0x6d0 mm/slub.c:6829
kvm_set_memory_region+0x9c4/0xb90 virt/kvm/kvm_main.c:2130
kvm_vm_ioctl_set_memory_region+0x6f/0xd0 virt/kvm/kvm_main.c:2154
kvm_vm_ioctl+0x957/0xc60 virt/kvm/kvm_main.c:5201
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:583
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0xfa0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Deliberately don't acquire filemap invalid lock when the file is dying as
the lifecycle of f_mapping is outside the purview of KVM. Dereferencing
the mapping is *probably* fine, but there's no need to invalidate anything
as memslot deletion is responsible for zapping SPTEs, and the only code
that can access the dying file is kvm_gmem_release(), whose core code is
mutually exclusive with unbinding.
Note, the mutual exclusivity is also what makes it safe to access the
bindings on a dying gmem instance. Unbinding either runs with slots_lock
held, or after the last reference to the owning "struct kvm" is put, and
kvm_gmem_release() nullifies the slot pointer under slots_lock, and puts
its reference to the VM after that is done.
Reported-by: syzbot+2479e53d0db9b32ae2aa@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/68fa7a22.a70a0220.3bf6c6.008b.GAE@google.com
Tested-by: syzbot+2479e53d0db9b32ae2aa@syzkaller.appspotmail.com
Fixes: a7800aa80e ("KVM: Add KVM_CREATE_GUEST_MEMFD ioctl() for guest-specific backing memory")
Cc: stable@vger.kernel.org
Cc: Hillf Danton <hdanton@sina.com>
Reviewed-By: Vishal Annapurve <vannapurve@google.com>
Link: https://patch.msgid.link/20251104011205.3853541-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Use a raw spinlock for vcpu_svm.ir_list_lock as the lock can be taken
during schedule() via kvm_sched_out() => __avic_vcpu_put(), and "normal"
spinlocks are sleepable locks when PREEMPT_RT=y.
This fixes the following lockdep warning:
=============================
[ BUG: Invalid wait context ]
6.12.0-146.1640_2124176644.el10.x86_64+debug #1 Not tainted
-----------------------------
qemu-kvm/38299 is trying to lock:
ff11000239725600 (&svm->ir_list_lock){....}-{3:3}, at: __avic_vcpu_put+0xfd/0x300 [kvm_amd]
other info that might help us debug this:
context-{5:5}
2 locks held by qemu-kvm/38299:
#0: ff11000239723ba8 (&vcpu->mutex){+.+.}-{4:4}, at: kvm_vcpu_ioctl+0x240/0xe00 [kvm]
#1: ff11000b906056d8 (&rq->__lock){-.-.}-{2:2}, at: raw_spin_rq_lock_nested+0x2e/0x130
stack backtrace:
CPU: 1 UID: 0 PID: 38299 Comm: qemu-kvm Kdump: loaded Not tainted 6.12.0-146.1640_2124176644.el10.x86_64+debug #1 PREEMPT(voluntary)
Hardware name: AMD Corporation QUARTZ/QUARTZ, BIOS RQZ100AB 09/14/2023
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xb0
__lock_acquire+0x921/0xb80
lock_acquire.part.0+0xbe/0x270
_raw_spin_lock_irqsave+0x46/0x90
__avic_vcpu_put+0xfd/0x300 [kvm_amd]
svm_vcpu_put+0xfa/0x130 [kvm_amd]
kvm_arch_vcpu_put+0x48c/0x790 [kvm]
kvm_sched_out+0x161/0x1c0 [kvm]
prepare_task_switch+0x36b/0xf60
__schedule+0x4f7/0x1890
schedule+0xd4/0x260
xfer_to_guest_mode_handle_work+0x54/0xc0
vcpu_run+0x69a/0xa70 [kvm]
kvm_arch_vcpu_ioctl_run+0xdc0/0x17e0 [kvm]
kvm_vcpu_ioctl+0x39f/0xe00 [kvm]
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://patch.msgid.link/20251030194130.307900-1-mlevitsk@redhat.com
[sean: massage changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Setup the per-CPU SVM data structures at the very end of hardware setup so
that svm_hardware_unsetup() can be used in svm_hardware_setup() to unwind
AVIC setup (for the GALog notifier). Alternatively, the error path could
do an explicit, manual unwind, e.g. by adding a helper to free the per-CPU
structures. But the per-CPU allocations have no interactions or
dependencies, i.e. can comfortably live at the end, and so converting to
a manual unwind would introduce churn and code without providing any
immediate advantage.
Link: https://patch.msgid.link/20251016190643.80529-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Update the comment above is_xstate_managed_msr() to note that
MSR_IA32_S_CET isn't saved/restored by XSAVES/XRSTORS.
MSR_IA32_S_CET isn't part of CET_U/S state as the SDM states:
The register state used by Control-Flow Enforcement Technology (CET)
comprises the two 64-bit MSRs (IA32_U_CET and IA32_PL3_SSP) that manage
CET when CPL = 3 (CET_U state); and the three 64-bit MSRs
(IA32_PL0_SSP–IA32_PL2_SSP) that manage CET when CPL < 3 (CET_S state).
Opportunistically shift the snippet about the safety of loading certain
MSRs to the function comment for kvm_access_xstate_msr(), which is where
the MSRs are actually loaded into hardware.
Fixes: e44eb58334 ("KVM: x86: Load guest FPU state when access XSAVE-managed MSRs")
Signed-off-by: Chao Gao <chao.gao@intel.com>
Link: https://patch.msgid.link/20251028060142.29830-1-chao.gao@intel.com
[sean: shift snippet about safety to kvm_access_xstate_msr()]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Assert, via KVM_BUG_ON(), that guest FPU state isn't/is in use when
loading/putting the FPU to help detect KVM bugs without needing an assist
from KASAN. If an imbalanced load/put is detected, skip the redundant
load/put to avoid clobbering guest state and/or crashing the host.
Note, kvm_access_xstate_msr() already provides a similar assertion.
Reviewed-by: Yao Yuan <yaoyuan@linux.alibaba.com>
Reviewed-by: Chao Gao <chao.gao@intel.com>
Link: https://patch.msgid.link/20251030185802.3375059-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Replace the hack added by commit f958bd2314 ("KVM: x86: Fix potential
put_fpu() w/o load_fpu() on MPX platform") with a more robust approach of
unloading+reloading guest FPU state based on whether or not the vCPU's FPU
is currently in-use, i.e. currently loaded. This fixes a bug on hosts
that support CET but not MPX, where kvm_arch_vcpu_ioctl_get_mpstate()
neglects to load FPU state (it only checks for MPX support) and leads to
KVM attempting to put FPU state due to kvm_apic_accept_events() triggering
INIT emulation. E.g. on a host with CET but not MPX, syzkaller+KASAN
generates:
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000004: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000020-0x0000000000000027]
CPU: 211 UID: 0 PID: 20451 Comm: syz.9.26 Tainted: G S 6.18.0-smp-DEV #7 NONE
Tainted: [S]=CPU_OUT_OF_SPEC
Hardware name: Google Izumi/izumi, BIOS 0.20250729.1-0 07/29/2025
RIP: 0010:fpu_swap_kvm_fpstate+0x3ce/0x610 ../arch/x86/kernel/fpu/core.c:377
RSP: 0018:ff1100410c167cc0 EFLAGS: 00010202
RAX: 0000000000000004 RBX: 0000000000000020 RCX: 00000000000001aa
RDX: 00000000000001ab RSI: ffffffff817bb960 RDI: 0000000022600000
RBP: dffffc0000000000 R08: ff110040d23c8007 R09: 1fe220081a479000
R10: dffffc0000000000 R11: ffe21c081a479001 R12: ff110040d23c8d98
R13: 00000000fffdc578 R14: 0000000000000000 R15: ff110040d23c8d90
FS: 00007f86dd1876c0(0000) GS:ff11007fc969b000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f86dd186fa8 CR3: 00000040d1dfa003 CR4: 0000000000f73ef0
PKRU: 80000000
Call Trace:
<TASK>
kvm_vcpu_reset+0x80d/0x12c0 ../arch/x86/kvm/x86.c:11818
kvm_apic_accept_events+0x1cb/0x500 ../arch/x86/kvm/lapic.c:3489
kvm_arch_vcpu_ioctl_get_mpstate+0xd0/0x4e0 ../arch/x86/kvm/x86.c:12145
kvm_vcpu_ioctl+0x5e2/0xed0 ../virt/kvm/kvm_main.c:4539
__se_sys_ioctl+0x11d/0x1b0 ../fs/ioctl.c:51
do_syscall_x64 ../arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x6e/0x940 ../arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f86de71d9c9
</TASK>
with a very simple reproducer:
r0 = openat$kvm(0xffffffffffffff9c, &(0x7f0000000000), 0x80b00, 0x0)
r1 = ioctl$KVM_CREATE_VM(r0, 0xae01, 0x0)
ioctl$KVM_CREATE_IRQCHIP(r1, 0xae60)
r2 = ioctl$KVM_CREATE_VCPU(r1, 0xae41, 0x0)
ioctl$KVM_SET_IRQCHIP(r1, 0x8208ae63, ...)
ioctl$KVM_GET_MP_STATE(r2, 0x8004ae98, &(0x7f00000000c0))
Alternatively, the MPX hack in GET_MP_STATE could be extended to cover CET,
but from a "don't break existing functionality" perspective, that isn't any
less risky than peeking at the state of in_use, and it's far less robust
for a long term solution (as evidenced by this bug).
Reported-by: Alexander Potapenko <glider@google.com>
Fixes: 69cc3e8865 ("KVM: x86: Add XSS support for CET_KERNEL and CET_USER")
Reviewed-by: Yao Yuan <yaoyuan@linux.alibaba.com>
Reviewed-by: Chao Gao <chao.gao@intel.com>
Link: https://patch.msgid.link/20251030185802.3375059-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
of_get_child_by_name() returns a node pointer with refcount incremented, we
should use of_node_put() on it when not needed anymore. Add the missing
of_node_put() to avoid refcount leak.
Fixes: 721cabf6c6 ("soc: imx: move PGC handling to a new GPC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Limit the workaround for the lack of the proper splash-screen handover
handling to the legacy ARM 32bit systems and replace forcing a sync_state
by explicite power domain shutdown. This approach lets compiler to
optimize it out on newer ARM 64bit systems.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 0745658aeb ("pmdomain: samsung: Fix splash-screen handover by enforcing a sync_state")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
nfsd exports a "pseudo root filesystem" which is used by NFSv4 to find
the various exported filesystems using LOOKUP requests from a known root
filehandle. NFSv3 uses the MOUNT protocol to find those exported
filesystems and so is not given access to the pseudo root filesystem.
If a v3 (or v2) client uses a filehandle from that filesystem,
nfsd_set_fh_dentry() will report an error, but still stores the export
in "struct svc_fh" even though it also drops the reference (exp_put()).
This means that when fh_put() is called an extra reference will be dropped
which can lead to use-after-free and possible denial of service.
Normal NFS usage will not provide a pseudo-root filehandle to a v3
client. This bug can only be triggered by the client synthesising an
incorrect filehandle.
To fix this we move the assignments to the svc_fh later, after all
possible error cases have been detected.
Reported-and-tested-by: tianshuo han <hantianshuo233@gmail.com>
Fixes: ef7f6c4904 ("nfsd: move V4ROOT version check to nfsd_set_fh_dentry()")
Signed-off-by: NeilBrown <neil@brown.name>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Since snd_soc_suspend() is invoked through snd_soc_pm_ops->suspend(),
and snd_soc_pm_ops is associated with the soc_driver (defined in
sound/soc/soc-core.c), and there is no parent-child relationship between
the soc_driver and the DA7213 codec driver, the power management subsystem
does not enforce a specific suspend/resume order between the DA7213 driver
and the soc_driver.
Because of this, the different codec component functionalities, called from
snd_soc_resume() to reconfigure various functions, can race with the
DA7213 struct dev_pm_ops::resume function, leading to misapplied
configuration. This occasionally results in clipped sound.
Fix this by dropping the struct dev_pm_ops::{suspend, resume} and use
instead struct snd_soc_component_driver::{suspend, resume}. This ensures
the proper configuration sequence is handled by the ASoC subsystem.
Cc: stable@vger.kernel.org
Fixes: 431e040065 ("ASoC: da7213: Add suspend to RAM support")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20251104114914.2060603-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Song Liu says:
====================
Fix ftrace for livepatch + BPF fexit programs
livepatch and BPF trampoline are two special users of ftrace. livepatch
uses ftrace with IPMODIFY flag and BPF trampoline uses ftrace direct
functions. When livepatch and BPF trampoline with fexit programs attach to
the same kernel function, BPF trampoline needs to call into the patched
version of the kernel function.
1/3 and 2/3 of this patchset fix two issues with livepatch + fexit cases,
one in the register_ftrace_direct path, the other in the
modify_ftrace_direct path.
3/3 adds selftests for both cases.
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
---
v4: https://patch.msgid.link/20251027175023.1521602-1-song@kernel.org
Changes v3 => v4:
1. Add helper reset_direct. (Steven)
2. Add Reviewed-by from Jiri.
3. Fix minor typo in comments.
v3: https://lore.kernel.org/bpf/20251026205445.1639632-1-song@kernel.org/
Changes v2 => v3:
1. Incorporate feedback by AI, which also fixes build error reported by
Steven and kernel test robot.
v2: https://lore.kernel.org/bpf/20251024182901.3247573-1-song@kernel.org/
Changes v1 => v2:
1. Target bpf tree. (Alexei)
2. Bring back the FTRACE_WARN_ON in __ftrace_hash_update_ipmodify
for valid code paths. (Steven)
3. Update selftests with cleaner way to find livepatch-sample.ko.
(offlline discussion with Ihor)
v1: https://lore.kernel.org/bpf/20251024071257.3956031-1-song@kernel.org/
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Both livepatch and BPF trampoline use ftrace. Special attention is needed
when livepatch and fexit program touch the same function at the same
time, because livepatch updates a kernel function and the BPF trampoline
need to call into the right version of the kernel function.
Use samples/livepatch/livepatch-sample.ko for the test.
The test covers two cases:
1) When a fentry program is loaded first. This exercises the
modify_ftrace_direct code path.
2) When a fentry program is loaded first. This exercises the
register_ftrace_direct code path.
Signed-off-by: Song Liu <song@kernel.org>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20251027175023.1521602-4-song@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
ftrace_hash_ipmodify_enable() checks IPMODIFY and DIRECT ftrace_ops on
the same kernel function. When needed, ftrace_hash_ipmodify_enable()
calls ops->ops_func() to prepare the direct ftrace (BPF trampoline) to
share the same function as the IPMODIFY ftrace (livepatch).
ftrace_hash_ipmodify_enable() is called in register_ftrace_direct() path,
but not called in modify_ftrace_direct() path. As a result, the following
operations will break livepatch:
1. Load livepatch to a kernel function;
2. Attach fentry program to the kernel function;
3. Attach fexit program to the kernel function.
After 3, the kernel function being used will not be the livepatched
version, but the original version.
Fix this by adding __ftrace_hash_update_ipmodify() to
__modify_ftrace_direct() and adjust some logic around the call.
Signed-off-by: Song Liu <song@kernel.org>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20251027175023.1521602-3-song@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
When livepatch is attached to the same function as bpf trampoline with
a fexit program, bpf trampoline code calls register_ftrace_direct()
twice. The first time will fail with -EAGAIN, and the second time it
will succeed. This requires register_ftrace_direct() to unregister
the address on the first attempt. Otherwise, the bpf trampoline cannot
attach. Here is an easy way to reproduce this issue:
insmod samples/livepatch/livepatch-sample.ko
bpftrace -e 'fexit:cmdline_proc_show {}'
ERROR: Unable to attach probe: fexit:vmlinux:cmdline_proc_show...
Fix this by cleaning up the hash when register_ftrace_function_nolock hits
errors.
Also, move the code that resets ops->func and ops->trampoline to the error
path of register_ftrace_direct(); and add a helper function reset_direct()
in register_ftrace_direct() and unregister_ftrace_direct().
Fixes: d05cb47066 ("ftrace: Fix modification of direct_function hash while in use")
Cc: stable@vger.kernel.org # v6.6+
Reported-by: Andrey Grodzovsky <andrey.grodzovsky@crowdstrike.com>
Closes: https://lore.kernel.org/live-patching/c5058315a39d4615b333e485893345be@crowdstrike.com/
Cc: Steven Rostedt (Google) <rostedt@goodmis.org>
Cc: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-and-tested-by: Andrey Grodzovsky <andrey.grodzovsky@crowdstrike.com>
Signed-off-by: Song Liu <song@kernel.org>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20251027175023.1521602-2-song@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
As part of a recent move go exclusively listing git.kernel.org trees
for the block and io_uring development, the "BLOCK LAYER" entry wasn't
updated as it already used git.kernel.org. However, outside of just
moving from git.kernel.dk to git.kernel.org, the "block" part of the
trees was also dropped, as the tree serves both block and io_uring
development trees.
Fix up the "BLOCK LAYER" entry so they all use the same tree.
Reported-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Update the text for firmware file naming to show that the l?u? suffix is
supported on CS35L56 B0 silicon and ampN was only used on early firmware.
The previous version of this text only said that B0 silicon used the ampN
suffix. Since kernel 6.16 the driver supports both the old ampN and
new l?u? suffix for B0 silicon. New firmwares will use the l?u? suffix.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20251103115809.33953-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This was supposed to pass "onenand" instead of "&onenand" with the
ampersand. Passing a random stack address which will be gone when the
function ends makes no sense. However the good thing is that the pointer
is never used, so this doesn't cause a problem at run time.
Fixes: e23abf4b77 ("mtd: OneNAND: S5PC110: Implement DMA interrupt method")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In the past two years, I have focused on EROFS and contributed features
including the reserved buffer pool, configurable global buffer pool, and
the ongoing direct I/O support for compressed data.
I would like to continue contributing to EROFS and help with code
reviews. Please CC me on EROFS-related changes.
Signed-off-by: Chunhai Guo <guochunhai@vivo.com>
Acked-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Acked-by: Chao Yu <chao@kernel.org>
Acked-by: Hongbo Li <lihongbo22@huawei.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
In commit 296602b8e5 ("arm64: dts: rockchip: Move RK3399 OPPs to dtsi
files for SoC variants"), everything shared between variants of RK3399
was put into rk3399-base.dtsi and the rest in variant-specific DTSI,
such as rk3399-t, rk3399-op1, rk3399, etc.
Therefore, the variant-specific DTSI should include rk3399-base.dtsi and
not another variant's DTSI.
rk3399-op1 wrongly includes rk3399 (a variant) DTSI instead of
rk3399-base DTSI, let's fix this oversight by including the intended
DTSI.
Fortunately, this had no impact on the resulting DTB since all nodes
were named the same and all node properties were overridden in
rk3399-op1.dtsi. This was checked by doing a checksum of rk3399-op1 DTBs
before and after this commit.
No intended change in behavior.
Fixes: 296602b8e5 ("arm64: dts: rockchip: Move RK3399 OPPs to dtsi files for SoC variants")
Cc: stable@vger.kernel.org
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://patch.msgid.link/20251029-rk3399-op1-include-v1-1-2472ee60e7f8@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Use a scope-based cleanup helper for the buffer allocated with kmalloc()
in ntrig_report_version() to simplify the cleanup logic and prevent
memory leaks (specifically the !hid_is_usb()-case one).
[jkosina@suse.com: elaborate on the actual existing leak]
Fixes: 185c926283 ("HID: hid-ntrig: fix unable to handle page fault in ntrig_report_version()")
Signed-off-by: Masami Ichikawa <masami256@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
There's currently no verification for host issued ranges in most of the
pKVM memory transitions. The end boundary might therefore be subject to
overflow and later checks could be evaded.
Close this loophole with an additional pfn_range_is_valid() check on a
per public function basis. Once this check has passed, it is safe to
convert pfn and nr_pages into a phys_addr_t and a size.
host_unshare_guest transition is already protected via
__check_host_shared_guest(), while assert_host_shared_guest() callers
are already ignoring host checks.
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Link: https://patch.msgid.link/20251016164541.3771235-1-vdonnefort@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
get-reg-list includes ZCR_EL2 in the list of EL2 registers that it looks
for when NV is enabled but does not have any feature gate for this register,
meaning that testing any combination of features that includes EL2 but does
not include SVE will result in a test failure due to a missing register
being reported:
| The following lines are missing registers:
|
| ARM64_SYS_REG(3, 4, 1, 2, 0),
Add ZCR_EL2 to feat_id_regs so that the test knows not to expect to see it
without SVE being enabled.
Fixes: 3a90b6f279 ("KVM: arm64: selftests: get-reg-list: Add base EL2 registers")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20251024-kvm-arm64-get-reg-list-zcr-el2-v1-1-0cd0ff75e22f@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Since GITS_TYPER.PTA == 0, the ITS MAPC command demands a CPU ID,
rather than a physical redistributor address, for its RDbase
command argument.
As such, when MAPC-ing guest ITS collections, vgic_lpi_stress iterates
over CPU IDs in the range [0, nr_cpus), passing them as the RDbase
vcpu_id argument to its_send_mapc_cmd().
However, its_encode_target() in the its_send_mapc_cmd() selftest
handler expects RDbase arguments to be formatted with a 16 bit
offset, as shown by the 16-bit target_addr right shift its implementation:
its_mask_encode(&cmd->raw_cmd[2], target_addr >> 16, 51, 16)
At the moment, all CPU IDs passed into its_send_mapc_cmd() have no
offset, therefore becoming 0x0 after the bit shift. Thus, when
vgic_its_cmd_handle_mapc() receives the ITS command in vgic-its.c,
it always interprets the RDbase target CPU as CPU 0. All interrupts
sent to collections will be processed by vCPU 0, which defeats the
purpose of this multi-vCPU test.
Fix by creating procnum_to_rdbase() helper function, which left-shifts
the vCPU parameter received by its_send_mapc_cmd 16 bits before passing
it to its_encode_target for encoding.
Signed-off-by: Maximilian Dittgen <mdittgen@amazon.de>
Link: https://patch.msgid.link/20251020145946.48288-1-mdittgen@amazon.de
Signed-off-by: Marc Zyngier <maz@kernel.org>
SONiX AK870 PRO keyboard pretends to be an apple keyboard by VID:PID,
rendering function keys not treated properly. Despite being a
SONiX USB DEVICE, it uses a different name, so adding it to the list.
Signed-off-by: April Grimoire <april@aprilg.moe>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Add a check to ensure locally generated packets (skb->sk != NULL) do
not use direct output in tunnel mode, as these packets require proper
L2 header setup that is handled by the normal XFRM processing path.
Fixes: 5eddd76ec2 ("xfrm: fix tunnel mode TX datapath in packet offload mode")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The GSO segmentation functions for ESP tunnel mode
(xfrm4_tunnel_gso_segment and xfrm6_tunnel_gso_segment) were
determining the inner packet's L2 protocol type by checking the static
x->inner_mode.family field from the xfrm state.
This is unreliable. In tunnel mode, the state's actual inner family
could be defined by x->inner_mode.family or by
x->inner_mode_iaf.family. Checking only the former can lead to a
mismatch with the actual packet being processed, causing GSO to create
segments with the wrong L2 header type.
This patch fixes the bug by deriving the inner mode directly from the
packet's inner protocol stored in XFRM_MODE_SKB_CB(skb)->protocol.
Instead of replicating the code, this patch modifies the
xfrm_ip2inner_mode helper function. It now correctly returns
&x->inner_mode if the selector family (x->sel.family) is already
specified, thereby handling both specific and AF_UNSPEC cases
appropriately.
With this change, ESP GSO can use xfrm_ip2inner_mode to get the
correct inner mode. It doesn't affect existing callers, as the updated
logic now mirrors the checks they were already performing externally.
Fixes: 26dbd66eab ("esp: choose the correct inner protocol for GSO on inter address family tunnels")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In the output path, xfrm_dev_offload_ok and xfrm_get_inner_ipproto
need to determine the protocol family of the inner packet (skb) before
it gets encapsulated.
In xfrm_dev_offload_ok, the code checked x->inner_mode.family. This is
unreliable because, for states handling both IPv4 and IPv6, the
relevant inner family could be either x->inner_mode.family or
x->inner_mode_iaf.family. Checking only the former can lead to a
mismatch with the actual packet being processed.
In xfrm_get_inner_ipproto, the code checked x->outer_mode.family. This
is also incorrect for tunnel mode, as the inner packet's family can be
different from the outer header's family.
At both of these call sites, the skb variable holds the original inner
packet. The most direct and reliable source of truth for its protocol
family is its destination entry. This patch fixes the issue by using
skb_dst(skb)->ops->family to ensure protocol-specific headers are only
accessed for the correct packet type.
Fixes: 91d8a53db2 ("xfrm: fix offloading of cross-family tunnels")
Fixes: 45a98ef492 ("net/xfrm: IPsec tunnel mode fix inner_ipproto setting in sec_path")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The keyboard of this device has the following in its report description
for Usage (Keyboard) in Collection (Application):
# 0x15, 0x00, // Logical Minimum (0) 52
# 0x25, 0x65, // Logical Maximum (101) 54
# 0x05, 0x07, // Usage Page (Keyboard) 56
# 0x19, 0x00, // Usage Minimum (0) 58
# 0x29, 0xdd, // Usage Maximum (221) 60
# 0x81, 0x00, // Input (Data,Arr,Abs) 62
Since the Usage Min/Max range exceeds the Logical Min/Max range,
keypresses outside the Logical range are not recognized. This includes,
for example, the Japanese language keyboard variant's keys for |, _ and
\.
Fixup the report description to make the Logical range match the Usage
range, fixing the interpretation of keypresses above 101 on this device.
Signed-off-by: Lauri Tirkkonen <lauri@hacktheplanet.fi>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Based on available evidence, the USB ID 4c4a:4155 used by multiple
devices has been attributed to Jieli. The commit 1a8953f4f7
("HID: Add IGNORE quirk for SMARTLINKTECHNOLOGY") affected touchscreen
functionality. Added checks for manufacturer and serial number to
maintain microphone compatibility, enabling both devices to function
properly.
[jkosina@suse.com: edit shortlog]
Fixes: 1a8953f4f7 ("HID: Add IGNORE quirk for SMARTLINKTECHNOLOGY")
Cc: stable@vger.kernel.org
Tested-by: staffan.melin@oscillator.se
Reviewed-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Signed-off-by: Zhang Heng <zhangheng@kylinos.cn>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
scx_bpf_cpuperf_set() has a typo where it dereferences the local
variable @sch, instead of the global @scx_root pointer. Fix by
dereferencing the correct variable.
Fixes: 956f2b11a8 ("sched_ext: Drop kf_cpu_valid()")
Signed-off-by: Andrea Righi <arighi@nvidia.com>
Reviewed-by: Christian Loehle <christian.loehle@arm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When a process tries to access an entry in /afs, normally what happens is
that an automount dentry is created by ->lookup() and then triggered, which
jumps through the ->d_automount() op. Currently, afs_dynroot_lookup() does
not do cell DNS lookup, leaving that to afs_d_automount() to perform -
however, it is possible to use access() or stat() on the automount point,
which will always return successfully, have briefly created an afs_cell
record if one did not already exist.
This means that something like:
test -d "/afs/.west" && echo Directory exists
will print "Directory exists" even though no such cell is configured. This
breaks the "west" python module available on PIP as it expects this access
to fail.
Now, it could be possible to make afs_dynroot_lookup() perform the DNS[*]
lookup, but that would make "ls --color /afs" do this for each cell in /afs
that is listed but not yet probed. kafs-client, probably wrongly, preloads
the entire cell database and all the known cells are then listed in /afs -
and doing ls /afs would be very, very slow, especially if any cell supplied
addresses but was wholly inaccessible.
[*] When I say "DNS", actually read getaddrinfo(), which could use any one
of a host of mechanisms. Could also use static configuration.
To fix this, make the following changes:
(1) Create an enum to specify the origination point of a call to
afs_lookup_cell() and pass this value into that function in place of
the "excl" parameter (which can be derived from it). There are six
points of origination:
- Cell preload through /proc/net/afs/cells
- Root cell config through /proc/net/afs/rootcell
- Lookup in dynamic root
- Automount trigger
- Direct mount with mount() syscall
- Alias check where YFS tells us the cell name is different
(2) Add an extra state into the afs_cell state machine to indicate a cell
that's been initialised, but not yet looked up. This is separate from
one that can be considered active and has been looked up at least
once.
(3) Make afs_lookup_cell() vary its behaviour more, depending on where it
was called from:
If called from preload or root cell config, DNS lookup will not happen
until we definitely want to use the cell (dynroot mount, automount,
direct mount or alias check). The cell will appear in /afs but stat()
won't trigger DNS lookup.
If the cell already exists, dynroot will not wait for the DNS lookup
to complete. If the cell did not already exist, dynroot will wait.
If called from automount, direct mount or alias check, it will wait
for the DNS lookup to complete.
(4) Make afs_lookup_cell() return an error if lookup failed in one way or
another. We try to return -ENOENT if the DNS says the cell does not
exist and -EDESTADDRREQ if we couldn't access the DNS.
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220685
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://patch.msgid.link/1784747.1761158912@warthog.procyon.org.uk
Fixes: 1d0b929fc0 ("afs: Change dynroot to create contents on demand")
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
The VBUS supply regulator is currently assigned to the PHY node.
This causes the VBUS to be always on, even when the controller
needs to be switched to peripheral mode.
Fix the OTG role switching by adding a connector node and moving
the VBUS supply regulator to that node. This way the VBUS gets
correctly switched according to the current role.
Fixes: 946ab10e3f ("arm64: dts: Add support for Kontron OSM-S i.MX8MP SoM and BL carrier board")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The msi-map property was incorrectly applied to pcie0-ep instead of
pcie1-ep. Correct the msi-map for both pcie0-ep and pcie1-ep nodes.
Fixes: bbe4b2f7d6 ("arm64: dts: imx95: Add msi-map for pci-ep device")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The gpio0_mipi_csi DT nodes are enabled by default, but they are
dependent on the irqsteer_csi nodes, which are not enabled. This causes
the gpio0_mipi_csi GPIOs to be probe deferred. Since these GPIOs can be
used independently of the CSI controller, enable irqsteer_csi by default
too to prevent them from being deferred and to ensure they work out of
the box.
Fixes: 2217f82437 ("arm64: dts: imx8: add capture controller for i.MX8's img subsystem")
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In former times, ext4 was enabled implicitely by enabling ext3 but with
the ext3 fs gone, it does not get enabled, which lets devices fail to
mount root on non-initrd based boots with an ext4 root.
Fixes: d6ace46c82 ("ext4: remove obsolete EXT3 config options")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "groups" property can hold multiple entries (e.g.
toshiba/tmpv7708-rm-mbrc.dts file), so allow that by dropping incorrect
type (pinmux-node.yaml schema already defines that as string-array) and
adding constraints for items. This fixes dtbs_check warnings like:
toshiba/tmpv7708-rm-mbrc.dtb: pinctrl@24190000 (toshiba,tmpv7708-pinctrl):
pwm-pins:groups: ['pwm0_gpio16_grp', 'pwm1_gpio17_grp', 'pwm2_gpio18_grp', 'pwm3_gpio19_grp'] is too long
Fixes: 1825c1fe00 ("pinctrl: Add DT bindings for Toshiba Visconti TMPV7700 SoC")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl-rtd driver uses 'devm_regmap_init_mmio', which requires
'REGMAP_MMIO' to be enabled.
Without this selection, the build fails with an undefined reference:
aarch64-none-linux-gnu-ld: drivers/pinctrl/realtek/pinctrl-rtd.o: in
function rtd_pinctrl_probe': pinctrl-rtd.c:(.text+0x5a0): undefined
reference to __devm_regmap_init_mmio_clk'
Fix this by selecting 'REGMAP_MMIO' in the Kconfig.
Fixes: e99ce78030 ("pinctrl: realtek: Add common pinctrl driver for Realtek DHC RTD SoCs")
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DMA device pointer `dma_dev` was being dereferenced before ensuring
that `cdns_ctrl->dmac` is properly initialized.
Move the assignment of `dma_dev` after successfully acquiring the DMA
channel to ensure the pointer is valid before use.
Fixes: d76d22b509 ("mtd: rawnand: cadence: use dma_map_resource for sdma address")
Cc: stable@vger.kernel.org
Signed-off-by: Niravkumar L Rabara <niravkumarlaxmidas.rabara@altera.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
While the user manual states that the PLL's rate should be between 180
MHz and 3 GHz in the register defninition section, it also says the
actual operating frequency is 22.5792*4 MHz in the PLL features table.
22.5792*4 MHz is one of the actual clock rates that we want and is
is available in the SDM table. Lower the minimum clock rate to 90 MHz
so that both rates in the SDM table can be used.
Fixes: 7cae1e2b55 ("clk: sunxi-ng: Add support for the A523/T527 CCU PLLs")
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20251020171059.2786070-7-wens@kernel.org
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
The "bus-r-dma" clock in the A523's PRCM clock controller is also
referred to as "DMA_CLKEN_SW" or "DMA ADB400 gating". It is unclear how
this ties into the DMA controller MBUS clock gate; however if the clock
is not enabled, the DMA controller in the MCU block will fail to access
DRAM, even failing to retrieve the DMA descriptors.
Mark this clock as critical. This sort of mirrors what is done for the
main DMA controller's MBUS clock, which has a separate toggle that is
currently left out of the main clock controller driver.
Fixes: 8cea339cfb ("clk: sunxi-ng: add support for the A523/T527 PRCM CCU")
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20251020171059.2786070-6-wens@kernel.org
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
If of_genpd_add_provider_onecell() fails during probe, the previously
created generic power domains are not removed, leading to a memory leak
and potential kernel crash later in genpd_debug_add().
Add proper error handling to unwind the initialized domains before
returning from probe to ensure all resources are correctly released on
failure.
Example crash trace observed without this fix:
| Unable to handle kernel paging request at virtual address fffffffffffffc70
| CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.18.0-rc1 #405 PREEMPT
| Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform
| pstate: 00000005 (nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : genpd_debug_add+0x2c/0x160
| lr : genpd_debug_init+0x74/0x98
| Call trace:
| genpd_debug_add+0x2c/0x160 (P)
| genpd_debug_init+0x74/0x98
| do_one_initcall+0xd0/0x2d8
| do_initcall_level+0xa0/0x140
| do_initcalls+0x60/0xa8
| do_basic_setup+0x28/0x40
| kernel_init_freeable+0xe8/0x170
| kernel_init+0x2c/0x140
| ret_from_fork+0x10/0x20
Fixes: 898216c97e ("firmware: arm_scmi: add device power domain support using genpd")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The rtl_ecc_engine_ops structure is only used to provide a set of
callback functions and is never modified after initialization.
Mark it as const so it can be placed in the read-only section, which
improves safety and allows better compiler optimization.
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The "req.start" and "req.len" variables are u64 values that come from the
user at the start of the function. We mask away the high 32 bits of
"req.len" so that's capped at U32_MAX but the "req.start" variable can go
up to U64_MAX which means that the addition can still integer overflow.
Use check_add_overflow() to fix this bug.
Fixes: 095bb6e44e ("mtdchar: add MEMREAD ioctl")
Fixes: 6420ac0af9 ("mtdchar: prevent unbounded allocation in MEMWRITE ioctl")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In statmount_string(), most flags assign an output offset pointer (offp)
which is later updated with the string offset. However, the
STATMOUNT_MNT_UIDMAP and STATMOUNT_MNT_GIDMAP cases directly set the
struct fields instead of using offp. This leaves offp uninitialized,
leading to a possible uninitialized dereference when *offp is updated.
Fix it by assigning offp for UIDMAP and GIDMAP as well, keeping the code
path consistent.
Fixes: 37c4a9590e ("statmount: allow to retrieve idmappings")
Fixes: e52e97f09f ("statmount: let unset strings be empty")
Cc: stable@vger.kernel.org
Signed-off-by: Zhen Ni <zhen.ni@easystack.cn>
Link: https://patch.msgid.link/20251013114151.664341-1-zhen.ni@easystack.cn
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Enabling compile testing should not enable every individual driver (we
have "allyesconfig" for that).
Fixes: 7cd8db0fb0 ("mmc: add COMPILE_TEST to multiple drivers")
Cc: Mikko Rapeli <mikko.rapeli@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current hlist_empty checks only test the first bucket of each
hashtable, ignoring any other bucket. They should be caught by the
WARN_ON for state_all, but better to make all the checks accurate.
Fixes: 73d189dce4 ("netns xfrm: per-netns xfrm_state_bydst hash")
Fixes: d320bbb306 ("netns xfrm: per-netns xfrm_state_bysrc hash")
Fixes: b754a4fd8f ("netns xfrm: per-netns xfrm_state_byspi hash")
Fixes: fe9f1d8779 ("xfrm: add state hashtable keyed by seq")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
xfrm_state_construct can fail without setting an error if the
requested pcpu_num value is too big. Set err and add an extack message
to avoid confusing userspace.
Fixes: 1ddf9916ac ("xfrm: Add support for per cpu xfrm state handling.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In case xfrm_state_migrate fails after calling xfrm_dev_state_add, we
directly release the last reference and destroy the new state, without
calling xfrm_dev_state_delete (this only happens in
__xfrm_state_delete, which we're not calling on this path, since the
state was never added).
Call xfrm_dev_state_delete on error when an offload configuration was
provided.
Fixes: ab244a394c ("xfrm: Migrate offload configuration")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In commit b441cf3f8c ("xfrm: delete x->tunnel as we delete x"), I
missed the case where state creation fails between full
initialization (->init_state has been called) and being inserted on
the lists.
In this situation, ->init_state has been called, so for IPcomp
tunnels, the fallback tunnel has been created and added onto the
lists, but the user state never gets added, because we fail before
that. The user state doesn't go through __xfrm_state_delete, so we
don't call xfrm_state_delete_tunnel for those states, and we end up
leaking the FB tunnel.
There are several codepaths affected by this: the add/update paths, in
both net/key and xfrm, and the migrate code (xfrm_migrate,
xfrm_state_migrate). A "proper" rollback of the init_state work would
probably be doable in the add/update code, but for migrate it gets
more complicated as multiple states may be involved.
At some point, the new (not-inserted) state will be destroyed, so call
xfrm_state_delete_tunnel during xfrm_state_gc_destroy. Most states
will have their fallback tunnel cleaned up during __xfrm_state_delete,
which solves the issue that b441cf3f8c (and other patches before it)
aimed at. All states (including FB tunnels) will be removed from the
lists once xfrm_state_fini has called flush_work(&xfrm_state_gc_work).
Reported-by: syzbot+999eb23467f83f9bf9bf@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=999eb23467f83f9bf9bf
Fixes: b441cf3f8c ("xfrm: delete x->tunnel as we delete x")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We're not updating x1, but we still need to put() it.
Fixes: a4a87fa4e9 ("xfrm: Add Direction to the SA in or out")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Add VMX exit handlers for SEAMCALL and TDCALL to inject a #UD if a non-TD
guest attempts to execute SEAMCALL or TDCALL. Neither SEAMCALL nor TDCALL
is gated by any software enablement other than VMXON, and so will generate
a VM-Exit instead of e.g. a native #UD when executed from the guest kernel.
Note! No unprivileged DoS of the L1 kernel is possible as TDCALL and
SEAMCALL #GP at CPL > 0, and the CPL check is performed prior to the VMX
non-root (VM-Exit) check, i.e. userspace can't crash the VM. And for a
nested guest, KVM forwards unknown exits to L1, i.e. an L2 kernel can
crash itself, but not L1.
Note #2! The Intel® Trust Domain CPU Architectural Extensions spec's
pseudocode shows the CPL > 0 check for SEAMCALL coming _after_ the VM-Exit,
but that appears to be a documentation bug (likely because the CPL > 0
check was incorrectly bundled with other lower-priority #GP checks).
Testing on SPR and EMR shows that the CPL > 0 check is performed before
the VMX non-root check, i.e. SEAMCALL #GPs when executed in usermode.
Note #3! The aforementioned Trust Domain spec uses confusing pseudocode
that says that SEAMCALL will #UD if executed "inSEAM", but "inSEAM"
specifically means in SEAM Root Mode, i.e. in the TDX-Module. The long-
form description explicitly states that SEAMCALL generates an exit when
executed in "SEAM VMX non-root operation". But that's a moot point as the
TDX-Module injects #UD if the guest attempts to execute SEAMCALL, as
documented in the "Unconditionally Blocked Instructions" section of the
TDX-Module base specification.
Cc: stable@vger.kernel.org
Cc: Kai Huang <kai.huang@intel.com>
Cc: Xiaoyao Li <xiaoyao.li@intel.com>
Cc: Rick Edgecombe <rick.p.edgecombe@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Binbin Wu <binbin.wu@linux.intel.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Reviewed-by: Binbin Wu <binbin.wu@linux.intel.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20251016182148.69085-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Rename the 'ssi2' and 'aud3' nodes to 'mux-ssi2' and 'mux-aud3' in the
audmux configuration of imx51-zii-rdu1.dts to comply with the naming
convention in imx-audmux.yaml.
This fixes the following dt-schema warning:
imx51-zii-rdu1.dtb: audmux@83fd0000 (fsl,imx51-audmux): 'aud3', 'ssi2'
do not match any of the regexes: '^mux-[0-9a-z]*$', '^pinctrl-[0-9]+$'
Fixes: ceef0396f3 ("ARM: dts: imx: add ZII RDU1 board")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'report-rate-hz' property for the edt-ft5x06 driver was added and
handled in the Linux kernel by me with patches [1] and [2] for this
specific board.
The v1 upstream version, which was the one applied to the customer's
kernel, used the 'report-rate' property, which was written directly to
the controller register. During review, the 'hz' suffix was added,
changing its handling so that writing the value directly to the register
was no longer possible for the M06 controller.
Once the patches were accepted in mainline, I did not reapply them to
the customer's kernel, and when upstreaming the DTS for this board, I
forgot to correct the 'report-rate-hz' property value.
The property must be set to 60 because this board uses the M06 controller,
which expects the report rate in units of 10 Hz, meaning the actual value
written to the register is 6.
[1] 625f829586 ("dt-bindings: input: touchscreen: edt-ft5x06: add report-rate-hz")
[2] 5bcee83a40 ("Input: edt-ft5x06 - set report rate by dts property")
Fixes: ffea3cac94 ("ARM: dts: imx6ul: support Engicam MicroGEA RMM board")
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In the pegasus_notetaker driver, the pegasus_probe() function allocates
the URB transfer buffer using the wMaxPacketSize value from
the endpoint descriptor. An attacker can use a malicious USB descriptor
to force the allocation of a very small buffer.
Subsequently, if the device sends an interrupt packet with a specific
pattern (e.g., where the first byte is 0x80 or 0x42),
the pegasus_parse_packet() function parses the packet without checking
the allocated buffer size. This leads to an out-of-bounds memory access.
Fixes: 1afca2b66a ("Input: add Pegasus Notetaker tablet driver")
Signed-off-by: Seungjin Bae <eeodqql09@gmail.com>
Link: https://lore.kernel.org/r/20251007214131.3737115-2-eeodqql09@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When executing kvm_riscv_vcpu_aia_has_interrupts, the vCPU may have
migrated and the IMSIC VS-file have not been updated yet, currently
the HGEIP CSR should be read from the imsic->vsfile_cpu ( the pCPU
before migration ) via on_each_cpu_mask, but this will trigger an
IPI call and repeated IPI within a period of time is expensive in
a many-core systems.
Just let the vCPU execute and update the correct IMSIC VS-file via
kvm_riscv_vcpu_aia_imsic_update may be a simple solution.
Fixes: 4cec89db80 ("RISC-V: KVM: Move HGEI[E|P] CSR access to IMSIC virtualization")
Signed-off-by: Fangyu Yu <fangyu.yu@linux.alibaba.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20251016012659.82998-1-fangyu.yu@linux.alibaba.com
Signed-off-by: Anup Patel <anup@brainfault.org>
"mac3" controller was removed from the initial version of fuji-data64
dts because the rgmii setting is incorrect, but dropping mac3 leads to
regression in the existing fuji platform, because fuji.dts simply
includes fuji-data64.dts.
This patch adds mac3 back to fuji-data64.dts to fix the fuji regression[1],
and rgmii settings need to be fixed later.
Fixes: b0f294fdfc ("ARM: dts: aspeed: facebook-fuji: Include facebook-fuji-data64.dts")
Link: https://lore.kernel.org/all/79ddc7b9-ef26-4959-9a16-aa4e006eb145@roeck-us.net/ [1]
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Mark the RTL8211F PHY as a wakeup source for the Jetson Xavier NX.
This allows the reworked RTL8211F driver to know that the PHY is
wired to wakeup capable hardware, and thus to expose WoL capabilities.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Unify the naming of the existing GPU OPP table nodes found in the RK3588
and RK3588J SoC dtsi files with the other SoC's GPU OPP nodes, following
the more "modern" node naming scheme.
Fixes: a7b2070505 ("arm64: dts: rockchip: Split GPU OPPs of RK3588 and RK3588j")
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
[opp-table also is way too generic on systems with like 4-5 opp-tables]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The 'rockchip,grf' property for tsadc in rk3328 wasn't actually used in
the driver and is no longer allowed in the DT since commit
e881662aa0 ("dt-bindings: thermal: rockchip: Tighten grf requirements")
So remove that property which fixes the following DT validation issue
tsadc@ff250000 (rockchip,rk3328-tsadc): rockchip,grf: False schema does not allow [[58]]
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable proper pin multiplexing for the I2S1 8-channel transmit interface by
adding the default pinctrl configuration which esures correct signal routing
and avoids pinmux conflicts during audio playback.
Changes fix the error
[ 116.856643] [ T782] rockchip-pinctrl pinctrl: pin gpio1-10 already requested by affinity_hint; cannot claim for fe410000.i2s
[ 116.857567] [ T782] rockchip-pinctrl pinctrl: error -EINVAL: pin-42 (fe410000.i2s)
[ 116.857618] [ T782] rockchip-pinctrl pinctrl: error -EINVAL: could not request pin 42 (gpio1-10) from group i2s1m0-sdi1 on device rockchip-pinctrl
[ 116.857659] [ T782] rockchip-i2s-tdm fe410000.i2s: Error applying setting, reverse things back
I2S1 on the M1 to the codec in the RK809 only uses the SCLK, LRCK, SDI0
and SDO0 signals, so limit the claimed pins to those.
With this change audio output works as expected:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: HDMI [HDMI], device 0: fe400000.i2s-i2s-hifi i2s-hifi-0 [fe400000.i2s-i2s-hifi i2s-hifi-0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: RK817 [Analog RK817], device 0: fe410000.i2s-rk817-hifi rk817-hifi-0 [fe410000.i2s-rk817-hifi rk817-hifi-0]
Subdevices: 1/1
Subdevice #0: subdevice #0
Fixes: 78f858447c ("arm64: dts: rockchip: Add analog audio on ODROID-M1")
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
[adapted the commit message a bit]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The reset line is being set to input on non-ACPI devices apparently to
save power. This isn't being done on ACPI devices as it's been found
that some ACPI devices don't have a pull-up resistor fitted. This can
also be the case for non-ACPI devices, resulting in:
[ 941.672207] Goodix-TS 1-0014: Error reading 10 bytes from 0x814e: -110
[ 942.696168] Goodix-TS 1-0014: Error reading 10 bytes from 0x814e: -110
[ 945.832208] Goodix-TS 1-0014: Error reading 10 bytes from 0x814e: -110
This behaviour appears to have been initialing introduced in
ec6e1b4082. This doesn't seem to be based on information in either the
GT911 or GT9271 datasheets cited as sources of information for this
change. Thus it seems likely that it is based on functionality in the
Android driver which it also lists. This behaviour may be viable in very
specific instances where the hardware is well known, but seems unwise in
the upstream kernel where such hardware requirements can't be
guaranteed.
Remove this over optimisation to improve reliability on non-ACPI
devices.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20251009134138.686215-1-martyn.welch@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The mt8189-pinctrl driver requires to probe that a device tree uses
in the device node the same names than mt8189_pinctrl_register_base_names
array. But they are not matching the required ones in the
"mediatek,mt8189-pinctrl" dt-bindings, leading to possible dtbs check
issues. The mt8189_pinctrl_register_base_names entry order is also
different.
So, align all mt8189_pinctrl_register_base_names entry names and order
on dt-bindings.
Fixes: a3fe1324c3 ("pinctrl: mediatek: Add pinctrl driver for mt8189")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mt8196-pinctrl driver requires to probe that a device tree uses
in the device node the same names than mt8196_pinctrl_register_base_names
array. But they are not matching the required ones in the
"mediatek,mt8196-pinctrl" dt-bindings, leading to possible dtbs check
issues.
So, align all mt8196_pinctrl_register_base_names entries on dt-bindings
ones.
Fixes: f7a29377c2 ("pinctrl: mediatek: Add pinctrl driver on mt8196")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2025-10-13 13:07:36 +02:00
1735 changed files with 243923 additions and 7832 deletions
description:Create a report to help us fix your issue
body:
- type:markdown
attributes:
value:|
**Is this the right place for my bug report?**
This repository contains the Linux kernel used on the Raspberry Pi.
If you believe that the issue you are seeing is kernel-related, this is the right place.
If not, we have other repositories for the GPU firmware at [github.com/raspberrypi/firmware](https://github.com/raspberrypi/firmware) and Raspberry Pi userland applications at [github.com/raspberrypi/userland](https://github.com/raspberrypi/userland).
If you have problems with the Raspbian distribution packages, report them in the [github.com/RPi-Distro/repo](https://github.com/RPi-Distro/repo).
If you simply have a question, then [the Raspberry Pi forums](https://www.raspberrypi.org/forums) are the best place to ask it.
- type:textarea
id:description
attributes:
label:Describe the bug
description:|
Add a clear and concise description of what you think the bug is.
validations:
required:true
- type:textarea
id:reproduce
attributes:
label:Steps to reproduce the behaviour
description:|
List the steps required to reproduce the issue.
validations:
required:true
- type:dropdown
id:model
attributes:
label:Device (s)
description:Onwhich device you are facing the bug?
multiple:true
options:
- Raspberry Pi Zero
- Raspberry Pi Zero W/WH
- Raspberry Pi Zero 2 W
- Raspberry Pi 1 Mod. A
- Raspberry Pi 1 Mod. A+
- Raspberry Pi 1 Mod. B
- Raspberry Pi 1 Mod. B+
- Raspberry Pi 2 Mod. B
- Raspberry Pi 2 Mod. B v1.2
- Raspberry Pi 3 Mod. A+
- Raspberry Pi 3 Mod. B
- Raspberry Pi 3 Mod. B+
- Raspberry Pi 4 Mod. B
- Raspberry Pi 400
- Raspberry Pi 5
- Raspberry Pi 500
- Raspberry Pi 500+
- Raspberry Pi CM0
- Raspberry Pi CM1
- Raspberry Pi CM3
- Raspberry Pi CM3 Lite
- Raspberry Pi CM3+
- Raspberry Pi CM3+ Lite
- Raspberry Pi CM4
- Raspberry Pi CM4 Lite
- Raspberry Pi CM5
- Raspberry Pi CM5 Lite
- Other
validations:
required:true
- type:textarea
id:system
attributes:
label:System
description:|
Copy and paste the URL returned from `raspinfo | pastebinit` into this section.
Alternatively, add answers to the following questions:
* Which OS and version (`cat /etc/rpi-issue`)?
* Which firmware version (`vcgencmd version`)?
* Which kernel version (`uname -a`)?
validations:
required:true
- type:textarea
id:logs
attributes:
label:Logs
description:|
If applicable, add the relevant output from `dmesg` or similar.
about:"Please do not use GitHub for asking questions. If you simply have a question, then the Raspberry Pi forums are the best place to ask it. Thanks in advance for helping us keep the issue tracker clean!"
- name:"⛔ Problems with Raspberry Pi OS packages"
url:https://github.com/RPi-Distro/repo
about:"If you have problems with a Raspberry Pi OS package, please report them at https://github.com/RPi-Distro/repo."
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
